Abstract: The application of the synchronous dynamic random
access memory (SDRAM) has gone beyond the scope of personal
computers for quite a long time. It comes into hand whenever a big
amount of low price and still high speed memory is needed. Most of
the newly developed stand alone embedded devices in the field of
image, video and sound processing take more and more use of it. The
big amount of low price memory has its trade off – the speed. In
order to take use of the full potential of the memory, an efficient
controller is needed. Efficient stands for maximum random accesses
to the memory both for reading and writing and less area after
implementation. This paper proposes a target device independent
DDR SDRAM pipelined controller and provides performance
comparison with available solutions.
Abstract: A Novel fuzzy neural network combining with support vector learning mechanism called support-vector-based fuzzy neural networks (SVBFNN) is proposed. The SVBFNN combine the capability of minimizing the empirical risk (training error) and expected risk (testing error) of support vector learning in high dimensional data spaces and the efficient human-like reasoning of FNN.
Abstract: The textural parameters, together with appearance and
flavor, are sensory attributes of great importance for the product to be
accepted by the consumer. The objective of the present study was the
evaluation of the textural attributes of Packhams pears in the fresh
state, after drying in a chamber with forced convection at 50ºC,
lyophilized and re-hydrated. In texture analysis it was used the
method of Texture Profile Analysis (TPA). The parameters analyzed
were hardness, cohesiveness, adhesiveness, elasticity and chewiness.
From the results obtained is possible to see that the drying operation
greatly affected some textural properties of the pears, so that the
hardness diminished very much with drying, for both drying
methods.
Abstract: Manufacturing tolerancing is intended to determine
the intermediate geometrical and dimensional states of the part
during its manufacturing process. These manufacturing dimensions
also serve to satisfy not only the functional requirements given in
the definition drawing, but also the manufacturing constraints, for
example geometrical defects of the machine, vibration and the
wear of the cutting tool. In this paper, an experimental study on the
influence of the wear of the cutting tool (systematic dispersions) is
explored. This study was carried out on three stages .The first stage
allows machining without elimination of dispersions (random,
systematic) so the tolerances of manufacture according to total
dispersions. In the second stage, the results of the first stage are
filtered in such way to obtain the tolerances according to random
dispersions. Finally, from the two previous stages, the systematic
dispersions are generated. The objective of this study is to model
by the least squares method the error of manufacture based on
systematic dispersion. Finally, an approach of optimization of the
manufacturing tolerances was developed for machining on a CNC
machine tool
Abstract: This paper describes the development of a numerical finite element algorithm used for the analysis of reinforced concrete structure equipped with shakes energy absorbing device subjected to earthquake excitation. For this purpose a finite element program code for analysis of reinforced concrete frame buildings is developed. The performance of developed program code is evaluated by analyzing of a reinforced concrete frame buildings model. The results are show that using damper device as seismic energy dissipation system effectively can reduce the structural response of framed structure during earthquake occurrence.
Abstract: This paper presents design and characterization of a
microaccelerometer designated for integration into cataract surgical
probe to detect hardness of different eye tissues during cataract
surgery. Soft posterior lens capsule of eye can be easily damaged in
comparison with hard opaque lens since the surgeon can not see
directly behind cutting needle during the surgery. Presence of
microsensor helps the surgeon to avoid rupturing posterior lens
capsule which if occurs leads to severe complications such as
glaucoma, infection, or even blindness. The microsensor having
overall dimensions of 480 μm x 395 μm is able to deliver significant
capacitance variations during encountered vibration situations which
makes it capable to distinguish between different types of tissue.
Integration of electronic components on chip ensures high level of
reliability and noise immunity while minimizes space and power
requirements. Physical characteristics and results on performance
testing, proves integration of microsensor as an effective tool to aid
the surgeon during this procedure.
Abstract: Energy consumption rate during the cooling process
of industrial glass tempering process is considerably high. In this
experimental study the effect of dimensionless jet to jet distance
(S/D) and jet to plate distance (H/D) on the cooling time have been
investigated. In the experiments 4 mm thick glass samples have been
used. Cooling unit consists of 16 mutually placed seamless aluminum
nozzles of 8 mm in diameter and 80 mm in length. Nozzles were in
staggered arrangement. Experiments were conducted with circular
jets for H/D values between 1 and 10, and for S/D values between 2
and 10. During the experiments Reynolds number has been kept
constant at 30000. Experimental results showed that the longest
cooling time with 87 seconds has been observed in the experiments
for S/D=10 and H/D=10 values, while the shortest cooling time with
42.5 seconds has been measured in the experiments for S/D=2 and
H/D=4 values.
Abstract: Most of the well known methods for generating
Gaussian variables require at least one standard uniform distributed
value, for each Gaussian variable generated. The length of the
random number generator therefore, limits the number of
independent Gaussian distributed variables that can be generated
meanwhile the statistical solution of complex systems requires a
large number of random numbers for their statistical analysis. We
propose an alternative simple method of generating almost infinite
number of Gaussian distributed variables using a limited number of
standard uniform distributed random numbers.
Abstract: The seismic feedback experiences in Algeria have
shown higher percentage of damages for non-code conforming
reinforced concrete (RC) buildings. Furthermore, the vulnerability of
these buildings was further aggravated due to presence of many
factors (e.g. weak the seismic capacity of these buildings, shorts
columns, Pounding effect, etc.).
Consequently Seismic risk assessments were carried out on
populations of buildings to identify the buildings most likely to
undergo losses during an earthquake. The results of such studies are
important in the mitigation of losses under future seismic events as
they allow strengthening intervention and disaster management plans
to be drawn up.
Within this paper, the state of the existing structures is assessed using
"the vulnerability index" method. This method allows the
classification of RC constructions taking into account both, structural
and non structural parameters, considered to be ones of the main
parameters governing the vulnerability of the structure. Based on
seismic feedback from past earthquakes DPM (damage probability
matrices) were developed too.
Abstract: The aim of this paper is to present the kinematic
analysis and mechanism design of an assistive robotic leg for
hemiplegic and hemiparetic patients. In this work, the priority is to
design and develop the lightweight, effective and single driver
mechanism on the basis of experimental hip and knee angles- data for
walking speed of 1 km/h. A mechanism of cam-follower with three
links is suggested for this purpose. The kinematic analysis is carried
out and analysed using commercialized MATLAB software based on
the prototype-s links sizes and kinematic relationships. In order to
verify the kinematic analysis of the prototype, kinematic analysis data
are compared with the experimental data. A good agreement between
them proves that the anthropomorphic design of the lower extremity
exoskeleton follows the human walking gait.
Abstract: The problem of controlling a two link robotic manipulator, consisting of a rotating and a prismatic links, is addressed. The actuations of both links are assumed to have unknown dead zone nonlinearities and friction torques modeled by LuGre friction model. Because of the existence of the unknown dead zone and friction torque at the actuations, unknown parameters and unmeasured states would appear to be part of the overall system dynamics that need for estimation. Unmeasured states observer, unknown parameters estimators, and robust adaptive control laws have been derived such that closed loop global stability is achieved. Simulation results have been performed to show the efficacy of the suggested approach.
Abstract: We address the problem of joint beamforming and multipath channel parameters estimation in Wideband Code Division Multiple Access (WCDMA) communication systems that employ Multiple-Access Interference (MAI) suppression techniques in the uplink (from mobile to base station). Most of the existing schemes rely on time multiplex a training sequence with the user data. In WCDMA, the channel parameters can also be estimated from a code multiplexed common pilot channel (CPICH) that could be corrupted by strong interference resulting in a bad estimate. In this paper, we present new methods to combine interference suppression together with channel estimation when using multiple receiving antennas by using adaptive signal processing techniques. Computer simulation is used to compare between the proposed methods and the existing conventional estimation techniques.
Abstract: An important goal of parboiling is a decrease of rice broken percentage and at the beginning Selected paddy of variety of rice Tarom and soaked at three different temperatures 45 Cº, 65 Cº and 80 Cº orderly for 5 hours, 4 hours and 1.5 hours to moisture of 40 % and then in steaming stage to operate these action two steaming methods are selected steaming under pressure condition and steaming in atmosphere pressure and In the first method after exerting air, the steam pressure is increase to 1 Kg/Cm2 which is done in two different duration times of 2.5 and 5 minutes and in second method used of three times of 5,10 and 15 minutes and dry to 8% moisture and decreases of rice broken percentage at best condition in variety of Tarom of 37.2 % to 7.3 % and increases yield percentage at best condition in variety of Tarom of 69.4 % to 75.93 % and bran percentage decreased in variety of Tarom of 9.53 % to 2.2-3.2 % and this issue cause increases yield percentage in rice and use of This method is very significant for our country because broken percentage of rice in our country is 23-33 %.
Abstract: Vertical Double Gate (DG) Metal Oxide Semiconductor Field Effect Transistor (MOSFET) is believed to suppress various short channel effect problems. The gate to channel coupling in vertical DG-MOSFET are doubled, thus resulting in higher current density. By having two gates, both gates are able to control the channel from both sides and possess better electrostatic control over the channel. In order to ensure that the transistor possess a superb turn-off characteristic, the subs-threshold swing (SS) must be kept at minimum value (60-90mV/dec). By utilizing SILVACO TCAD software, an n-channel vertical DG-MOSFET was successfully designed while keeping the sub-threshold swing (SS) value as minimum as possible. From the observation made, the value of sub-threshold swing (SS) was able to be varied by adjusting the height of the silicon pillar. The minimum value of sub-threshold swing (SS) was found to be 64.7mV/dec with threshold voltage (VTH) of 0.895V. The ideal height of the vertical DG-MOSFET pillar was found to be at 0.265 µm.
Abstract: This study investigated the use of modified
atmosphere packaging (MAP) and different packaging to extend the
shelf life of Barbari flat bread. Three atmospheres including 70%CO2
and 30%N2, 50% CO2 and 50%N2 and a normal air as control were
used. The bread samples were packaged in three type pouches. The
shelf life was determined by appearance of mold and yeast (M +Y) in
Barbari bread samples stored at 25 ± 1°C and 38 ± 2% relative
humidity. The results showed that it is possible to prolong the shelf
life of Barbari bread from four days to about 21 days by using
modified atmosphere packaging with high carbon dioxide
concentration and high-barrier laminated and vacuum bags packages.
However, the hardness of samples kept in MAP increase significantly
by increase of carbon dioxide concentration. The correlation
coefficient (r) between headspace CO2 concentration and hardness
was 0.997, 0.997 and 0.599 for A, B and C packaging respectively.
High negative correlation coefficients were found between the crumb
moisture and the hardness values in various packaging. There were
significant negative correlation coefficients between sensory
parameters and hardness of texture.
Abstract: In order to give high expertise the computer aided
design of mechanical systems involves specific activities focused on
processing two type of information: knowledge and data. Expert rule
based knowledge is generally processing qualitative information and
involves searching for proper solutions and their combination into
synthetic variant. Data processing is based on computational models
and it is supposed to be inter-related with reasoning in the knowledge
processing. In this paper an Intelligent Integrated System is proposed,
for the objective of choosing the adequate material. The software is
developed in Prolog – Flex software and takes into account various
constraints that appear in the accurate operation of gears.
Abstract: Insider abuse has recently been reported as one of
the more frequently occurring security incidents, suggesting that
more security is required for detecting and preventing unauthorised
financial transactions entered by authorised users. To address the
problem, and based on the observation that all authorised interbanking
financial transactions trigger or are triggered by other
transactions in a workflow, we have developed a security solution
based on a redefined understanding of an audit workflow. One audit
workflow where there is a log file containing the complete workflow
activity of financial transactions directly related to one financial
transaction (an electronic deal recorded at an e-trading system). The
new security solution contemplates any two parties interacting on
the basis of financial transactions recorded by their users in related
but distinct automated financial systems. In the new definition interorganizational
and intra-organization interactions can be described
in one unique audit trail. This concept expands the current ideas of
audit trails by adapting them to actual e-trading workflow activity, i.e.
intra-organizational and inter-organizational activity. With the above,
a security auditing service is designed to detect integrity drifts with
and between organizations in order to detect unauthorised financial
transactions entered by authorised users.
Abstract: During last decades, worldwide researchers dedicated
efforts to develop machine-based seismic Early Warning systems,
aiming at reducing the huge human losses and economic damages.
The elaboration time of seismic waveforms is to be reduced in order
to increase the time interval available for the activation of safety
measures. This paper suggests a Data Mining model able to correctly
and quickly estimate dangerousness of the running seismic event.
Several thousand seismic recordings of Japanese and Italian
earthquakes were analyzed and a model was obtained by means of a
Bayesian Network (BN), which was tested just over the first
recordings of seismic events in order to reduce the decision time and
the test results were very satisfactory.
The model was integrated within an Early Warning System
prototype able to collect and elaborate data from a seismic sensor
network, estimate the dangerousness of the running earthquake and
take the decision of activating the warning promptly.
Abstract: This paper aims to fabricated high quality anodic
aluminum oxide (AAO) film by anodization method. AAO pore size,
pore density, and film thickness can be controlled in 10~500 nm,
108~1011 pore．cm-2, and 1~100 μm. AAO volume and surface area can
be computed based on structural parameters such as thickness, pore
size, pore density, and sample size. Base on the thetorical calculation,
AAO has 100 μm thickness with 15 nm, 60 nm, and 500 nm pore
diameters AAO surface areas are 1225.2 cm2, 3204.4 cm2, and 549.7
cm2, respectively. The large unit surface area which is useful for
adsorption application. When AAO adsorbed pH indictor of
bromphenol blue presented a sensitive pH detection of solution
change. This testing method can further be used for the precise
measurement of biotechnology, convenience measurement of
industrial engineering.
Abstract: The implementation of single-electron tunneling
(SET) simulators based on the master-equation (ME) formalism
requires the efficient and accurate identification of an exhaustive list
of active states and related tunnel events. Dynamic simulations also
require the control of the emerging states and guarantee the safe
elimination of decaying states. This paper describes algorithms for
use in the stationary and dynamic control of the lists of active states
and events. The paper presents results obtained using these
algorithms with different SET structures.