Abstract: This paper presents the experimental results of silicone rubber polymer insulators for 22 kV systems under salt water dip wheel test based on IEC 62217. Straight shed silicone rubber polymer insulators having leakage distance 685 mm were tested continuously 30,000 cycles. One test cycle includes 4 positions, energized, de-energized, salt water dip and deenergized, respectively. For one test cycle, each test specimen remains stationary for about 40 second in each position and takes 8 second for rotate to next position. By visual observation, sever surface erosion was observed on the trunk near the energized end of tested specimen. Puncture was observed on the upper shed near the energized end. In addition, decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Furthermore, chemical analysis by ATR-FTIR was conducted in order to elucidate the chemical change of tested specimens comparing with new specimen.
Abstract: The purposes of this paper are to (1) promote excellence in computer science by suggesting a cohesive innovative approach to fill well documented deficiencies in current computer science education, (2) justify (using the authors' and others anecdotal evidence from both the classroom and the real world) why this approach holds great potential to successfully eliminate the deficiencies, (3) invite other professionals to join the authors in proof of concept research. The authors' experiences, though anecdotal, strongly suggest that a new approach involving visual modeling technologies should allow computer science programs to retain a greater percentage of prospective and declared majors as students become more engaged learners, more successful problem-solvers, and better prepared as programmers. In addition, the graduates of such computer science programs will make greater contributions to the profession as skilled problem-solvers. Instead of wearily rememorizing code as they move to the next course, students will have the problem-solving skills to think and work in more sophisticated and creative ways.
Abstract: The inphase/quadrature (I/Q) amplitude and phase
imbalance effects are studied in coherent optical orthogonal
frequency division multiplexing (CO-OFDM) systems. An analytical
model for the I/Q imbalance is developed and supported by
simulation results. The results indicate that the I/Q imbalance degrades the BER performance considerably.
Abstract: With Power system movement toward restructuring along with factors such as life environment pollution, problems of transmission expansion and with advancement in construction technology of small generation units, it is expected that small units like wind turbines, fuel cells, photovoltaic, ... that most of the time connect to the distribution networks play a very essential role in electric power industry. With increase in developing usage of small generation units, management of distribution networks should be reviewed. The target of this paper is to present a new method for optimal management of active and reactive power in distribution networks with regard to costs pertaining to various types of dispersed generations, capacitors and cost of electric energy achieved from network. In other words, in this method it-s endeavored to select optimal sources of active and reactive power generation and controlling equipments such as dispersed generations, capacitors, under load tapchanger transformers and substations in a way that firstly costs in relation to them are minimized and secondly technical and physical constraints are regarded. Because the optimal management of distribution networks is an optimization problem with continuous and discrete variables, the new evolutionary method based on Ant Colony Algorithm has been applied. The simulation results of the method tested on two cases containing 23 and 34 buses exist and will be shown at later sections.
Abstract: PT XYZ is a bottled drinking water company. To preserve production resources owned by the company so that the resources could be utilized well, it has implemented maintenance management system, which has important role in company's profitability, and is one of the factors influenced overall company's performance. Yet, up to now the company has never measured maintenance activities' contribution to company's performance. Performance evaluation is done according to adapted Balanced Scorecard model fitted to maintenance function context. This model includes six perspectives: innovation and growth, production, maintenance, environment, costumer, and finance. Actual performance measurement is done through Analytic Hierarchy Process and Objective Matrix. From the research done, we can conclude that the company's maintenance function is categorized in moderate performance. But, there are some indicators which has high priority but low performance, which are: costumers' complain rate, work lateness rate, and Return on Investment.
Abstract: The hydrolysis kinetics of polycrystalline lithium hydride (LiH) in argon at various low humidities was measured by gravimetry and Raman spectroscopy with ambient water concentration ranging from 200 to 1200 ppm. The results showed that LiH hydrolysis curve revealed a paralinear shape, which was attributed to two different reaction stages that forming different products as explained by the 'Layer Diffusion Control' model. Based on the model, a novel two-stage rate equation for LiH hydrolysis reactions was developed and used to fit the experimental data for determination of Li2O steady thickness Hs and the ultimate hydrolysis rate vs. The fitted data presented a rise of Hs as ambient water concentration cw increased. However, in spite of the negative effect imposed by Hs increasing, the upward trend of vs remained, which implied that water concentration, rather than Li2O thickness, played a predominant role in LiH hydrolysis kinetics. In addition, the proportional relationship between vsHs and cw predicted by rate equation and confirmed by gravimetric data validated the model in such conditions.
Abstract: Bagging and boosting are among the most popular resampling ensemble methods that generate and combine a diversity of classifiers using the same learning algorithm for the base-classifiers. Boosting algorithms are considered stronger than bagging on noisefree data. However, there are strong empirical indications that bagging is much more robust than boosting in noisy settings. For this reason, in this work we built an ensemble using a voting methodology of bagging and boosting ensembles with 10 subclassifiers in each one. We performed a comparison with simple bagging and boosting ensembles with 25 sub-classifiers, as well as other well known combining methods, on standard benchmark datasets and the proposed technique was the most accurate.
Abstract: The study and development of an innovative material
for building insulation is really important for a sustainable society in order to improve comfort and reducing energy consumption. The aim of this work is the development of insulating panels for
sustainable buildings based on an innovative material made by
cardboard and Phase Change Materials (PCMs).
The research has consisted in laboratory tests whose purpose has been the obtaining of the required properties for insulation panels: lightweight, porous structures and mechanical resistance. PCMs have been used for many years in the building industry as
smart insulation technology because of their properties of storage and release high quantity of latent heat at useful specific temperatures [1]- [2].
The integration of PCMs into cellulose matrix during the waste paper recycling process has been developed in order to obtain a
composite material.
Experiments on the productive process for the realization of insulating panels were done in order to make the new material
suitable for building application. The addition of rising agents
demonstrated the possibility to obtain a lighter structure with better
insulation properties.
Several tests were conducted to verify the new panel properties. The results obtained have shown the possibility to realize an
innovative and sustainable material suitable to replace insulating panels currently used.
Abstract: Iron ore and coal are the two major important raw
materials being used in Iron making industries. Usually ore fines
containing around 5% Alumina are rejected due to higher proportion
of alumina. Therefore, a technology or process which may reduce
the alumina content by 2% by beneficiation process will be highly
attractive . In addition fine coals with ash content is used nearly 12%
is directly injected in blast furnace. Fast fluidization is a technology
by using dry beneficiation of coal and iron ore can be done. During
the fluidization process the iron ore band coal is fluidized at high
velocity in the riser of a fast fluidized bed, the heavier and coarse
particles is generally settled at the bottom in a dense zone of the riser
while the finer and lighter particle are entrained to the top dilute zone
and then via a cyclone is fed back to the bottom of the riser column.
Most of the alumina and low ash fine size coals being lighter are
expected to move up to the riser and by a natural beneficiation of
ores is expected to take place in the riser. Therefore in this study an
attempt has been made for dry beneficiation of iron ore and coal in a
fluidized bed and its hydrodynamic characterization.
Abstract: Over the past years, the EMCCD has had a profound
influence on photon starved imaging applications relying on its unique
multiplication register based on the impact ionization effect in the
silicon. High signal-to-noise ratio (SNR) means high image quality.
Thus, SNR improvement is important for the EMCCD. This work
analyzes the SNR performance of an EMCCD with gain off and on. In
each mode, simplified SNR models are established for different
integration times. The SNR curves are divided into readout noise (or
CIC) region and shot noise region by integration time. Theoretical
SNR values comparing long frame integration and frame adding in
each region are presented and discussed to figure out which method is
more effective. In order to further improve the SNR performance,
pixel binning is introduced into the EMCCD. The results show that
pixel binning does obviously improve the SNR performance, but at the
expensive of the spatial resolution.
Abstract: In the present study, the pressure drop and laminar convection heat transfer characteristics of nanofluids in microchannel heat sink with square duct are numerically investigated. The water based nanofluids created with Al2O3 and CuO particles in four different volume fractions of 0%, 0.5%, 1%, 1.5% and 2% are used to analyze their effects on heat transfer and the pressure drop. Under the laminar, steady-state flow conditions, the finite volume method is used to solve the governing equations of heat transfer. Mixture Model is considered to simulate the nanofluid flow. For verification of used numerical method, the results obtained from numerical calculations were compared with the results in literature for both pure water and the nanofluids in different volume fractions. The distributions of the particles in base fluid are assumed to be uniform. The results are evaluated in terms of Nusselt number, the pressure drop and heat transfer enhancement. Analysis shows that the nanofluids enhance heat transfer while the Reynolds number and the volume fractions are increasing. The best overall enhancement was obtained at φ=%2 and Re=100 for CuO-water nanofluid.
Abstract: The authors present a mixed method for reducing the order of the large-scale dynamic systems. In this method, the denominator polynomial of the reduced order model is obtained by using the modified pole clustering technique while the coefficients of the numerator are obtained by Pade approximations. This method is conceptually simple and always generates stable reduced models if the original high-order system is stable. The proposed method is illustrated with the help of the numerical examples taken from the literature.
Abstract: Proteins levels produced by bacteria may be increased
in stressful surroundings, such as in the presence of antibiotics. It
appears that many antimicrobial agents or antibiotics, when used at
low concentrations, have in common the ability to activate or repress
gene transcription, which is distinct from their inhibitory effect.
There have been comparatively few studies on the potential of
antibiotics or natural compounds in nature as a specific chemical
signal that can trigger a variety of biological functions. Therefore,
this study was focusing on the effect of essential oils from
Cymbopogon flexuosus and C. nardus in regulating proteins
production by Bacillus subtilis ATCC 21332. The Minimum
Inhibition Concentrations (MICs) of both essential oils on B. subtilis
were determined by using microdilution assay, resulting 0.2% and
1.56% for each C. flexuosus and C. nardus subsequently. The
bacteria were further exposed to each essential oils at concentration
of 0.01XMIC for 2 days. The proteins were then isolated and
analyzed by sodium dodecyl sulfate polyacrylamide gel
electrophoresis (SDS-PAGE). Protein profile showed that a band
with approximate size of 250 kD was appeared for the treated
bacteria with essential oils. Thus, Bacillus subtilis ATCC 21332 in
stressful condition with the presence of essential oils at low
concentration could induce the protein production.
Abstract: In this paper, a double balanced radio frequency multiplier
is presented which is customized for transmitted reference
ultra wideband (UWB) receivers. The multiplier uses 90nm model
parameters and exploits compensating transistors to provide controllable
gain for a Gilbert core. After performing periodic and quasiperiodic
non linear analyses the RF mixer (multiplier) achieves a
voltage conversion gain of 16 dB and a DSB noise figure of 8.253
dB with very low power consumption. A high degree of LO to RF
isolation (in the range of -94dB), RF to IF isolation (in the range of
-95dB) and LO to IF isolation (in the range of -143dB) is expected
for this design with an input-referred IP3 point of -1.93 dBm and an
input referred 1 dB compression point of -10.67dBm. The amount of
noise at the output is 7.7 nV/√Hz when the LO input is driven by
a 10dBm signal. The mixer manifests better results when compared
with other reported multiplier circuits and its Zero-IF performance
ensures its applicability as TR-UWB multipliers.
Abstract: The Elliptic Curve Digital Signature Algorithm
(ECDSA) is the elliptic curve analogue of DSA, where it is a digital
signature scheme designed to provide a digital signature based on a
secret number known only to the signer and also on the actual
message being signed. These digital signatures are considered the
digital counterparts to handwritten signatures, and are the basis for
validating the authenticity of a connection. The security of these
schemes results from the infeasibility to compute the signature
without the private key. In this paper we introduce a proposed to
development the original ECDSA with more complexity.
Abstract: Arthrobacter viscosus biomass was used for Cr(VI)
biosorption. The effect of pH on Cr(VI) reduction and removal from
aqueous solution was studied in the range of 1-4. The Cr(VI) removal
involves both redox reaction and adsorption of metal ions on biomass
surface. The removal rate of Cr(VI) was enhanced by very acid
conditions, while higher solution pH values favored the removal of
total chromium. The best removal efficiency and uptake were
reached at pH 4, 72.5 % and 12.6 mgCr/gbiomass, respectively.
Abstract: In the paper we submit the non-local modification of
kinetic Smoluchowski equation for binary aggregation applying to
dispersed media having memory. Our supposition consists in that that
intensity of evolution of clusters is supposed to be a function of the
product of concentrations of the lowest orders clusters at different
moments. The new form of kinetic equation for aggregation is
derived on the base of the transfer kernels approach. This approach
allows considering the influence of relaxation times hierarchy on
kinetics of aggregation process in media with memory.
Abstract: Transportation is of great importance in the current
life of human beings. The transportation system plays many roles,
from economical development to after-catastrophe aids such as
rescue operation in the first hours and days after an earthquake. In
after earthquakes response phase, transportation system acts as a
basis for ground operations including rescue and relief operation,
food providing for victims and etc. It is obvious that partial or
complete obstruction of this system results in the stop of these
operations. Bridges are one of the most important elements of
transportation network. Failure of a bridge, in the most optimistic
case, cuts the relation between two regions and in more developed
countries, cuts the relation of numerous regions. In this paper, to
evaluate the vulnerability and estimate the damage level of Tehran
bridges, HAZUS method, developed by Federal Emergency
Management Agency (FEMA) with the aid of National Institute of
Building Science (NIBS), is used for the first time in Iran. In this
method, to evaluate the collapse probability, fragility curves are
used. Iran is located on seismic belt and thus, it is vulnerable to
earthquakes. Thus, the study of the probability of bridge collapses, as
an important part of transportation system, during earthquakes is of
great importance. The purpose of this study is to provide fragility
curves for Gisha Bridge, one of the longest steel bridges in Tehran,
as an important lifeline element. Besides, the damage probability for
this bridge during a specific earthquake, introduced as scenario
earthquakes, is calculated. The fragility curves show that for the
considered scenario, the probability of occurrence of complete
collapse for the bridge is 8.6%.
Abstract: As chip manufacturing technology is suddenly on the
threshold of major evaluation, which shrinks chip in size and
performance, LFSR (Linear Feedback Shift Register) is implemented
in layout level which develops the low power consumption chip,
using recent CMOS, sub-micrometer layout tools. Thus LFSR
counter can be a new trend setter in cryptography and is also
beneficial as compared to GRAY & BINARY counter and variety of
other applications.
This paper compares 3 architectures in terms of the hardware
implementation, CMOS layout and power consumption, using
Microwind CMOS layout tool. Thus it provides solution to a low
power architecture implementation of LFSR in CMOS VLSI.
Abstract: It is known that the heart interacts with and adapts to its venous and arterial loading conditions. Various experimental studies and modeling approaches have been developed to investigate the underlying mechanisms. This paper presents a model of the left ventricle derived based on nonlinear stress-length myocardial characteristics integrated over truncated ellipsoidal geometry, and second-order dynamic mechanism for the excitation-contraction coupling system. The results of the model presented here describe the effects of the viscoelastic damping element of the electromechanical coupling system on the hemodynamic response. Different heart rates are considered to study the pacing effects on the performance of the left-ventricle against constant preload and afterload conditions under various damping conditions. The results indicate that the pacing process of the left ventricle has to take into account, among other things, the viscoelastic damping conditions of the myofilament excitation-contraction process. The effects of left ventricular dimensions on the hemdynamic response have been examined. These effects are found to be different at different viscoelastic and pacing conditions.