Abstract: In the LFC problem, the interconnections among some areas are the input of disturbances, and therefore, it is important to suppress the disturbances by the coordination of governor systems. In contrast, tie-line power flow control by TCPS located between two areas makes it possible to stabilize the system frequency oscillations positively through interconnection, which is also expected to provide a new ancillary service for the further power systems. Thus, a control strategy using controlling the phase angle of TCPS is proposed for provide active control facility of system frequency in this paper. Also, the optimum adjustment of PID controller's parameters in a robust way under bilateral contracted scenario following the large step load demands and disturbances with and without TCPS are investigated by Particle Swarm Optimization (PSO), that has a strong ability to find the most optimistic results. This newly developed control strategy combines the advantage of PSO and TCPS and has simple stricture that is easy to implement and tune. To demonstrate the effectiveness of the proposed control strategy a three-area restructured power system is considered as a test system under different operating conditions and system nonlinearities. Analysis reveals that the TCPS is quite capable of suppressing the frequency and tie-line power oscillations effectively as compared to that obtained without TCPS for a wide range of plant parameter changes, area load demands and disturbances even in the presence of system nonlinearities.
Abstract: The behavior of three phase five leg transformer under voltage sag is studied in this paper. This paper proposes a simple, practical model of a three phase-five leg, saturated transformer with accurate performance. Transformer saturation is produced when the voltage sag is recovered and it causes inrush current in transformer. Effects of voltage sag depth, duration and initial point on wave have been analyzed in this paper. Initial point on wave can produce maximum inrush current in five leg transformers while comparing with three leg transformers. The magnetic circuit symmetry of five leg transformer produces the more symmetrical shape of inrush current curves versus initial point on wave and sag duration than three leg transformer. The simulations show that current peak has a periodical dependence on sag duration and linear dependence on sag depth. Inrush current that is produced in three phase five leg transformer is higher than three phase three leg transformer.
Abstract: In this paper, a tooth shape optimization method for
cogging torque reduction in Permanent Magnet (PM) motors is
developed by using the Reduced Basis Technique (RBT) coupled by
Finite Element Analysis (FEA) and Design of Experiments (DOE)
methods. The primary objective of the method is to reduce the
enormous number of design variables required to define the tooth
shape. RBT is a weighted combination of several basis shapes. The
aim of the method is to find the best combination using the weights
for each tooth shape as the design variables. A multi-level design
process is developed to find suitable basis shapes or trial shapes at
each level that can be used in the reduced basis technique. Each level
is treated as a separated optimization problem until the required
objective – minimum cogging torque – is achieved. The process is
started with geometrically simple basis shapes that are defined by
their shape co-ordinates. The experimental design of Taguchi method
is used to build the approximation model and to perform
optimization. This method is demonstrated on the tooth shape
optimization of a 8-poles/12-slots PM motor.
Abstract: Buildings are considered as significant part in the
cities, which plays main role in organization and arrangement of city
appearance, which is affects image of that building facades, as an
connective between inner and outer space, have a main role in city
image and they are classified as rich image and poor image by people
evaluation which related to visual architectural and urban elements in
building facades. the buildings in Karimi street , in Lahijan city
where, lies in north of Iran, contain the variety of building's facade
types which, have made a city image in Historical part of Lahijan
city, while reflected the Iranian cities identity. The study attempt to
identify the architectural and urban elements that impression the
image of building facades in historical area, based on public
evaluation. Quantitative method were used and the data was collected
through questionnaire survey, the result presented architectural style,
color, shape, and design evaluated by people as most important factor
which should be understate in future development. in fact, the rich
architectural style with strong design make strong city image as weak
design make poor city image.
Abstract: Drying characteristics of rough rice (variety of lenjan) with an initial moisture content of 25% dry basis (db) was studied in a hot air dryer assisted by infrared heating. Three arrival air temperatures (30, 40 and 500C) and four infrared radiation intensities (0, 0.2 , 0.4 and 0.6 W/cm2) and three arrival air speeds (0.1, 0.15 and 0.2 m.s-1) were studied. Bending strength of brown rice kernel, percentage of cracked kernels and time of drying were measured and evaluated. The results showed that increasing the drying arrival air temperature and radiation intensity of infrared resulted decrease in drying time. High bending strength and low percentage of cracked kernel was obtained when paddy was dried by hot air assisted infrared dryer. Between this factors and their interactive effect were a significant difference (p
Abstract: This research is intended to develop a raw material allocation model in timber processing industry in Perum Perhutani Unit I, Central Java, Indonesia. The model can be used to determine the quantity of allocation of timber between chain in the supply chain to select supplier considering factors that are log price and the distance. In determining the quantity of allocation of timber between chains in the supply chain, the model considers the optimal inventory in each chain. Whilst the optimal inventory is determined based on demand forecast, the capacity and safety stock. Problem solving allocation is conducted by developing linear programming model that aims to minimize the total cost of the purchase, transportation cost and storage costs at each chain. The results of numerical examples show that the proposed model can generate savings of the purchase cost of 20.84% and select suppliers with mileage closer.
Abstract: Compacted clay liners (CCLs) are the main materials
used in waste disposal landfills due to their low permeability. In this
study, the effect on the shear resistant of clays with inorganic salt
solutions as permeate fluid was experimentally investigated. For this
purpose, NaCl inorganic salt solution at concentrations of 2, 5, 10%
and deionized water were used. Laboratory direct shear and Vane
shear tests were conducted on three compacted clays with low,
medium and high plasticity. Results indicated that the solutions type
and its concentration affect the shear properties of the mixture. In the
light of this study, the influence magnitude of these inorganic salts in
varies concentrations in different clays were determined and more
suitable compacted clay with the compare of plasticity were found.
Abstract: In this study, the numerical solution of unsteady flow
between two concentric rotating spheres with suction and blowing at
their boundaries is presented. The spheres are rotating about a
common axis of rotation while their angular velocities are constant.
The Navier-Stokes equations are solved by employing the finite
difference method and implicit scheme. The resulting flow patterns
are presented for various values of the flow parameters including
rotational Reynolds number Re , and a blowing/suction Reynolds
number Rew . Viscous torques at the inner and the outer spheres are
calculated, too. It is seen that increasing the amount of suction and
blowing decrease the size of eddies generated in the annulus.
Abstract: This paper presents the modeling results of an
innovative system for the temperature control in the interior
compartment of a stationary automobile facing the solar energy from
the sun. A very thin layer of PCM inside a pouch placed in the
ceiling of the car in which the heating energy is absorbed and release
with melting and solidification of phase change materials. As a result
the temperature of the car interior is maintained in the comfort
condition. The amount of required PCM has been calculated to be
about 755 g. The PCM-temperature controlling system is simple and
has a potential to be implemented as a practical solution to prevent
undesirable heating of the automobile-s cabin.
Abstract: Different methods containing biometric algorithms are
presented for the representation of eigenfaces detection including
face recognition, are identification and verification. Our theme of this
research is to manage the critical processing stages (accuracy, speed,
security and monitoring) of face activities with the flexibility of
searching and edit the secure authorized database. In this paper we
implement different techniques such as eigenfaces vector reduction
by using texture and shape vector phenomenon for complexity
removal, while density matching score with Face Boundary Fixation
(FBF) extracted the most likelihood characteristics in this media
processing contents. We examine the development and performance
efficiency of the database by applying our creative algorithms in both
recognition and detection phenomenon. Our results show the
performance accuracy and security gain with better achievement than
a number of previous approaches in all the above processes in an
encouraging mode.
Abstract: The new idea of this research is application of a new fault detection and isolation (FDI) technique for supervision of sensor networks in transportation system. In measurement systems, it is necessary to detect all types of faults and failures, based on predefined algorithm. Last improvements in artificial neural network studies (ANN) led to using them for some FDI purposes. In this paper, application of new probabilistic neural network features for data approximation and data classification are considered for plausibility check in temperature measurement. For this purpose, two-phase FDI mechanism was considered for residual generation and evaluation.
Abstract: In this study an extensive experimental research is
carried out to develop a better understanding of the effects of Piano Key (PK) weir geometry on weir flow threshold submergence.
Experiments were conducted in a 12 m long, 0.4 m wide and 0.7 m deep rectangular glass wall flume. The main objectives were to
investigate the effect of the PK weir geometries including the weir
length, weir height, inlet-outlet key widths, upstream and
downstream apex overhangs, and slopped floors on threshold submergence and study the hydraulic flow characteristics. From the
experimental results, a practical formula is proposed to evaluate the flow threshold submergence over PK weirs.
Abstract: Imaging is defined as the process of obtaining
geometric images either two dimensional or three dimensional by scanning or digitizing the existing objects or products. In this research, it applied to retrieve 3D information of the human skin
surface in medical application. This research focuses on analyzing
and determining volume of leg ulcers using imaging devices. Volume
determination is one of the important criteria in clinical assessment of leg ulcer. The volume and size of the leg ulcer wound will give the
indication on responding to treatment whether healing or worsening.
Different imaging techniques are expected to give different result (and accuracies) in generating data and images. Midpoint projection
algorithm was used to reconstruct the cavity to solid model and compute the volume. Misinterpretation of the results can affect the
treatment efficacy. The objectives of this paper is to compare the
accuracy between two 3D data acquisition method, which is laser
triangulation and structured light methods, It was shown that using models with known volume, that structured-light-based 3D technique
produces better accuracy compared with laser triangulation data
acquisition method for leg ulcer volume determination.
Abstract: In an electric power system, spinning reserve
requirements can be determined by using deterministic and/or
probabilistic measures. Although deterministic methods are usual in
many systems, application of probabilistic methods becomes
increasingly important in the new environment of the electric power
utility industry. This is because of the increased uncertainty
associated with competition. In this paper 1) a new probabilistic
method is presented which considers the reliability of transmission
system in a simplified manner and 2) deterministic and probabilistic
methods are compared. The studied methods are applied to the Roy
Billinton Test System (RBTS).
Abstract: Biological Ammonia removal (nitrification), the
oxidation of ammonia to nitrate catalyzed by bacteria, is a key part of
global nitrogen cycling. In the first step of nitrification,
chemolithoautotrophic ammonia oxidizer transform ammonia to
nitrite, this subsequently oxidized to nitrate by nitrite oxidizing
bacteria. This process can be affected by several factors. In this study
the effect of influent COD on biological ammonia removal in a
bench-scale biological reactor was investigated. Experiments were
carried out using synthetic wastewater. The initial ammonium
concentration was 25mgNH4
+-N L-1. The effect of COD between
247.55±1.8 and 601.08±3.24mgL-1 on biological ammonia removal
was investigated by varying the COD loading supplied to reactor.
From the results obtained in this study it could be concluded in the
range of 247.55±1.8 to 351.35±2.05mgL-1, there is a direct
relationship between amount of COD and ammonia removal.
However more than 351.35±2.05 up to 601.08±3.24mgL-1 were
found an indirect relationship between them.
Abstract: This paper present a MATLAB-SIMULINK model of a single phase 2.5 KVA, 240V RMS controlled PV VSI (Photovoltaic Voltage Source Inverter) inverter using IGBTs (Insulated Gate Bipolar Transistor). The behavior of output voltage, output current, and the total harmonic distortion (THD), with the variation in input dc blocking capacitor (Cdc), for linear and non-linear load has been analyzed. The values of Cdc as suggested by the other authors in their papers are not clearly defined and it poses difficulty in selecting the proper value. As the dc power stored in Cdc, (generally placed parallel with battery) is used as input to the VSI inverter. The simulation results shows the variation in the output voltage and current with different values of Cdc for linear and non-linear load connected at the output side of PV VSI inverter and suggest the selection of suitable value of Cdc.