Abstract: According to the Auckland climate, building passive
design more focus on improving winter indoor thermal and health
conditions. Based on field study data of indoor air temperature and
relative humidity close to ceiling and floor of an insulated Auckland
townhouse with and without a whole home mechanical ventilation
system, this study is to analysis variation of indoor microclimate data
of an Auckland townhouse using or not using the mechanical
ventilation system to evaluate winter indoor thermal and health
conditions for the future house design with a mechanical ventilation
system.
Abstract: The building sector is the largest energy consumer and
CO2 emitter in the European Union (EU) and therefore the active
reduction of energy consumption and elimination of energy wastage
are among the main goals in it. Healthy housing and energy
efficiency are affected by many factors which set challenges to
monitoring, control and research of indoor air quality (IAQ) and
energy consumption, especially in old buildings. These challenges
include measurement and equipment costs, for example.
Additionally, the measurement results are difficult to interpret and
their usage in the ventilation control is also limited when taking into
account the energy efficiency of housing at the same time. The main
goal of this study is to develop a cost-effective building monitoring
and control system especially for old buildings. The starting point or
keyword of the development process is a wireless system; otherwise
the installation costs become too high. As the main result, this paper
describes an idea of a wireless building monitoring and control
system. The first prototype of the system has been installed in 10
residential buildings and in 10 school buildings located in the City of
Kuopio, Finland.
Abstract: The work presented in this study is related to an
energy system analysis based on passive cooling system for
dwellings. It consists to solar chimney energy performances
determination versus geometrical and environmental considerations
as the size and inlet width conditions of the chimney. Adrar site
located in the southern region of Algeria is chosen for this study
according to ambient temperature and solar irradiance technical data
availability. Obtained results are related to the glazing temperature
distributions, the chimney air flow and internal wall temperatures.
The air room change per hour (ACH) parameter, the outlet air
velocity and mass air flow rate are also determined. It is shown that
the chimney width has a significant effect on energy performances
compared to its entry size. A good agreement is observed between
these results and those obtained by others from the literature.
Abstract: Appropriate ventilation in a classroom is helpful for
enhancing air exchange rate and student concentration. This study
focuses on the effects of fenestration in a four-story school building by
performing numerical simulation of a building when considering
indoor and outdoor environments simultaneously. The wind profile
function embedded in PHOENICS code was set as the inlet boundary
condition in a suburban environment. Sixteen fenestration
combinations were compared in a classroom containing thirty seats.
This study evaluates mean age of air (AGE) and airflow pattern of a
classroom on different floors. Considering both wind profile and
fenestration effects, the airflow on higher floors is channeled toward
the area near ceiling in a room and causes older mean age of air in the
breathing zone. The results in this study serve as a useful guide for
enhancing natural ventilation in a typical school building.
Abstract: Growing world population has fundamental impacts
and often catastrophic on natural habitat. The immethodical
consumption of energy, destruction of the forests and extinction of
plant and animal species are the consequence of this experience.
Urban sustainability and sustainable urban development, that is so
spoken these days, should be considered as a strategy, goal and
policy, beyond just considering environmental issues and protection.
The desert-s climate has made a bunch of problems for its residents.
Very hot and dry climate in summers of the Iranian desert areas,
when there was no access to modern energy source and mechanical
cooling systems in the past, made Iranian architects to design a
natural ventilation system in their buildings. The structure, like a
tower going upward the roof, besides its ornamental application and
giving a beautiful view to the building, was used as a spontaneous
ventilation system. In this paper, it has been tried to name the
problems of the area and it-s inconvenience, then some answers has
pointed out in order to solve the problems and as an alternative
solution BADGIR (wind-catcher) has been introduced as a solution
knowing that it has been playing a major role in dealing with the
problems.
Abstract: The quality of Ribbed Smoked Sheets
(RSS) primarily based on color, dryness, and the presence or
absence of fungus and bubbles. This quality is strongly
influenced by the drying and fumigation process namely
smoking process. Smoking that is held in high temperature
long time will result scorched dark brown sheets, whereas if
the temperature is too low or slow drying rate would resulted
in less mature sheets and growth of fungus. Therefore need to
find the time and temperature for optimum quality of sheets.
Enhance, unmonitored heat and mass transfer during smoking
process lead to high losses of energy balance. This research
aims to generate simple empirical mathematical model
describing the effect of smoking time and temperature to RSS
quality of color, water content, fungus and bubbles. The
second goal of study was to analyze energy balance during
smoking process. Experimental study was conducted by
measuring temperature, residence time and quality parameters
of 16 sheets sample in smoking rooms. Data for energy
consumption balance such as mass of fuel wood, mass of
sheets being smoked, construction temperature, ambient
temperature and relative humidity were taken directly along
the smoking process. It was found that mathematical model
correlating smoking temperature and time with color is Color
= -169 - 0.184 T4 - 0.193 T3 - 0.160 0.405 T1 + T2 + 0.388 t1
+3.11 t2 + 3.92t3 + 0.215 t4 with R square 50.8% and with
moisture is Moisture = -1.40-0.00123 T4 + 0.00032 T3 +
0.00260 T2 - 0.00292 T1 - 0.0105 t1 + 0.0290 t2 + 0.0452 t3
+ 0.00061 t4 with R square of 49.9%. Smoking room energy
analysis found useful energy was 27.8%. The energy stored in
the material construction 7.3%. Lost of energy in conversion
of wood combustion, ventilation and others were 16.6%. The
energy flowed out through the contact of material construction
with the ambient air was found to be the highest contribution
to energy losses, it reached 48.3%.
Abstract: The present paper was concerned primarily with the
analysis, simulation of the air flow and thermal patterns in a lecture
room. The paper is devoted to numerically investigate the influence
of location and number of ventilation and air conditioning supply and
extracts openings on air flow properties in a lecture room. The work
focuses on air flow patterns, thermal behaviour in lecture room where
large number of students. The effectiveness of an air flow system is
commonly assessed by the successful removal of sensible and latent
loads from occupants with additional of attaining air pollutant at a
prescribed level to attain the human thermal comfort conditions and
to improve the indoor air quality; this is the main target during the
present paper. The study is carried out using computational fluid
dynamics (CFD) simulation techniques as embedded in the
commercially available CFD code (FLUENT 6.2). The CFD
modelling techniques solved the continuity, momentum and energy
conservation equations in addition to standard k – ε model equations
for turbulence closure.
Throughout the investigations, numerical validation is carried out by
way of comparisons of numerical and experimental results. Good
agreement is found among both predictions.
Abstract: The objective of this paper was to designing a
ventilation system to enhance the performance of roof solar collector
(RSC) for reducing heat accumulation inside the house. The RSC has
1.8 m2 surface area made of CPAC monier roof tiles on the upper part
and gypsum board on the lower part. The space between CPAC
monier and gypsum board was fixed at 14 cm.
Ventilation system of modified roof solar collector (modified
RSC) consists of 9 tubes of 0.15m diameter and installed in the
lower part of RSC. Experimental result showed that the temperature
of the room, and attic temperature. The average temperature
reduction of room of house used modified RSC is about 2oC. and the
percentage of room temperature reduction varied between 0 to 10%.
Therefore, modified RSC is an interesting option in the sense that it
promotes solar energy and conserve energy.
Abstract: The paper presents the results of simple measurements
conducted on a model of a wind-driven venturi-type room ventilator.
The ventilator design is new and was developed employing
mathematical modeling. However, the computational model was not
validated experimentally for the particular application considered.
The paper presents the performance of the ventilator model under
laboratory conditions, for five different wind tunnel speeds. The
results are used to both demonstrate the effectiveness of the new
design and to validate the computational model employed to develop
it.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: The sanitary sewerage connection rate becomes an
important indicator of advanced cities. Following the construction of
sanitary sewerages, the maintenance and management systems are
required for keeping pipelines and facilities functioning well. These
maintenance tasks often require sewer workers to enter the manholes
and the pipelines, which are confined spaces short of natural
ventilation and full of hazardous substances. Working in sewers could
be easily exposed to a risk of adverse health effects. This paper
proposes the use of Bayesian belief networks (BBN) as a higher level
of noncarcinogenic health risk assessment of sewer workers. On the
basis of the epidemiological studies, the actual hospital attendance
records and expert experiences, the BBN is capable of capturing the
probabilistic relationships between the hazardous substances in sewers
and their adverse health effects, and accordingly inferring the
morbidity and mortality of the adverse health effects. The provision of
the morbidity and mortality rates of the related diseases is more
informative and can alleviate the drawbacks of conventional methods.
Abstract: Natural ventilation is an important means to improve indoor thermal comfort and reduce the energy consumption. A solar chimney system is an enhancing natural draft device, which uses solar radiation to heat the air inside the chimney, thereby converting the thermal energy into kinetic energy. The present study considered some parameters such as chimney width and solar intensity, which were believed to have a significant effect on space ventilation. Fluent CFD software was used to predict buoyant air flow and flow rates in the cavities. The results were compared with available published experimental and theoretical data from the literature. There was an acceptable trend match between the present results and the published data for the room air change per hour, ACH. Further, it was noticed that the solar intensity has a more significant effect on ACH.
Abstract: Passive systems were born with the purpose of the
greatest exploitation of solar energy in cold climates and high
altitudes. They spread themselves until the 80-s all over the world
without any attention to the specific climate and the summer
behavior; this caused the deactivation of the systems due to a series
of problems connected to the summer overheating, the complex
management and the rising of the dust.
Until today the European regulation limits only the winter
consumptions without any attention to the summer behavior but, the
recent European EN 15251 underlines the relevance of the indoor
comfort, and the necessity of the analytic studies validation by
monitoring case studies.
In the porpose paper we demonstrate that the solar wall is an
efficient system both from thermal comfort and energy saving point
of view and it is the most suitable for our temperate climates because
it can be used as a passive cooling sistem too. In particular the paper
present an experimental and numerical analisys carried out on a case
study with nine different solar passive systems in Ancona, Italy.
We carried out a detailed study of the lodging provided by the
solar wall by the monitoring and the evaluation of the indoor
conditions.
Analyzing the monitored data, on the base of recognized models
of comfort (ISO, ASHRAE, Givoni-s BBCC), is emerged that the
solar wall has an optimal behavior in the middle seasons. In winter
phase this passive system gives more advantages in terms of energy
consumptions than the other systems, because it gives greater heat
gain and therefore smaller consumptions. In summer, when outside
air temperature return in the mean seasonal value, the indoor comfort
is optimal thanks to an efficient transversal ventilation activated from
the same wall.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: The study deals with the modelling of the gas flow during heliox therapy. A special model has been developed to study the effect of the helium upon the gas flow in the airways during the spontaneous breathing. Lower density of helium compared with air decreases the Reynolds number and it allows improving the flow during the spontaneous breathing. In the cases, where the flow becomes turbulent while the patient inspires air the flow is still laminar when the patient inspires heliox. The use of heliox decreases the work of breathing and improves ventilation. It allows in some cases to prevent the intubation of the patients.
Abstract: This paper investigates experimental and numerical study of the airflow characteristics for vortex, round and square ceiling diffusers and its effect on the thermal comfort in a ventilated room. Three different thermal comfort criteria namely; Mean Age of the Air (MAA), ventilation effectiveness (E), and Effective Draft Temperature (EDT) have been used to predict the thermal comfort zone inside the room. In experimental work, a sub-scale room is set-up to measure the temperature field in the room. In numerical analysis, unstructured grids have been used to discretize the numerical domain. Conservation equations are solved using FLUENT commercial flow solver. The code is validated by comparing the numerical results obtained from three different turbulence models with the available experimental data. The comparison between the various numerical models shows that the standard k-ε turbulence model can be used to simulate these cases successfully. After validation of the code, effect of supply air velocity on the flow and thermal field could be investigated and hence the thermal comfort. The results show that the pressure coefficient created by the square diffuser is 1.5 times greater than that created by the vortex diffuser. The velocity decay coefficient is nearly the same for square and round diffusers and is 2.6 times greater than that for the vortex diffuser.
Abstract: The objective of this study is to investigate fire
behaviors, experimentally and numerically, in a scaled version of an
underground station. The effect of ventilation velocity on the fire is
examined. Fire experiments are simulated by burning 10 ml
isopropyl alcohol fuel in a fire pool with dimensions 5cm x 10cm x 4
mm at the center of 1/100 scaled underground station model. A
commercial CFD program FLUENT was used in numerical
simulations. For air flow simulations, k-ω SST turbulence model and
for combustion simulation, non-premixed combustion model are
used. This study showed that, the ventilation velocity is increased
from 1 m/s to 3 m/s the maximum temperature in the station is found
to be less for ventilation velocity of 1 m/s. The reason for these
experimental result lies on the relative dominance of oxygen supply
effect on cooling effect. Without piston effect, maximum temperature
occurs above the fuel pool. However, when the ventilation velocity
increased the flame was tilted in the direction of ventilation and the
location of maximum temperature moves along the flow direction.
The velocities measured experimentally in the station at different
locations are well matched by the CFD simulation results. The
prediction of general flow pattern is satisfactory with the smoke
visualization tests. The backlayering in velocity is well predicted by
CFD simulation. However, all over the station, the CFD simulations
predicted higher temperatures compared to experimental
measurements.
Abstract: There is a great deal of interest in constructing Double Skin Facade (DSF) structures which are considered as modern movement in field of Energy Conservation, renewable energies, and Architecture design. This trend provides many conclusive alternatives which are frequently associated with sustainable building. In this paper a building with Double Skin Facade is considered in the semiarid climate of Tehran, Iran, in order to consider the DSF-s performance during hot seasons. Mathematical formulations calculate solar heat gain by the external skin. Moreover, Computational Fluid Dynamics (CFD) simulations were performed on the case study building to enhance effectiveness of the facade. The conclusion divulged difference of gained energy by the cavity and room with and without blind and louvers. Some solutions were introduced to surge the performance of natural ventilation by plunging the cooling loads in summer.
Abstract: Public awareness towards green energy are on the rise and this can be prove by many product being manufactured or prerequired to be made as energy saving devices mainly to save consumer from spending more on utility billing. These schemes are popular nowadays and many homemade appliances are turned into energy saving gadget which attracts the attention of consumers. Knowing the public demands and pattern towards purchasing home appliances thus the idea of “energy saving suction hood (ESSH)" is proposed. The ESSH can be used in many places that require smoke ventilation or even to reduce the room temperature as many conventional suction hoods (CSH) do, but this device works automatically by the usage of sensors that detects the smoke/temperature and automatically spins the exhaust fan. As it turns, the mechanical rotation rotates the AC generator which is coupled together with the fan and then charges the battery. The innovation of this product is, it does not rely on the utility supply as it is also hook up with a solar panel which also charges the battery, Secondly, it generates energy as the exhaust fan mechanically rotates. Thirdly, an energy loop back feature is introduced to this system which will supply for the ventilator fan. Another major innovation is towards interfacing this device with an in house production of generator. This generator is produced by proper design on stator as well as rotor to reduce the losses. A comparison is made between the ESSH and the CSH and result shows that the ESSH saves 172.8kWh/year of utility supply which is used by CSH. This amount of energy can save RM 3.14 from monthly utility bill and a total of RM 37.67 per year. In fact this product can generate 175 Watt of power from generator(75W) and solar panel(100W) that can be used either to supply other household appliances and/or to loop back to supply the fans motor. The innovation of this system is essential for future production of other equipment by using the loopback power method and turning most equipment into a standalone system.
Abstract: Clean air in subway station is important to passengers. The Platform Screen Doors (PSDs) can improve indoor air quality in the subway station; however the air quality in the subway tunnel is degraded. The subway tunnel has high CO2 concentration and indoor particulate matter (PM) value. The Indoor Air Quality (IAQ) level in subway environment degrades by increasing the frequency of the train operation and the number of the train. The ventilation systems of the subway tunnel need improvements to have better air-quality. Numerical analyses might be effective tools to analyze the performance of subway twin-track tunnel ventilation systems. An existing subway twin-track tunnel in the metropolitan Seoul subway system is chosen for the numerical simulations. The ANSYS CFX software is used for unsteady computations of the airflow inside the twin-track tunnel when the train moves. The airflow inside the tunnel is simulated when one train runs and two trains run at the same time in the tunnel. The piston-effect inside the tunnel is analyzed when all shafts function as the natural ventilation shaft. The supplied air through the shafts is mixed with the pollutant air in the tunnel. The pollutant air is exhausted by the mechanical ventilation shafts. The supplied and discharged airs are balanced when only one train runs in the twin-track tunnel. The pollutant air in the tunnel is high when two trains run simultaneously in opposite direction and all shafts functioned as the natural shaft cases when there are no electrical power supplies in the shafts. The remained pollutant air inside the tunnel enters into the station platform when the doors are opened.