Abstract: This paper presents an analytical study of Small Unmanned Aerial Vehicle (SUAV) dynamic stability derivatives. Simulating SUAV dynamics and analyzing its behavior at the earliest design stages is too important and more efficient design aspect. The approach suggested in this paper is using the wind tunnel experiment to collect the aerodynamic data and get the dynamic stability derivatives. AutoCAD Software was used to draw the case study (wildlife surveillance SUAV). The SUAV is scaled down to be 0.25% of the real SUAV dimensions and converted to a wind tunnel model. The model was tested in three different speeds for three different attitudes which are; pitch, roll and yaw. The wind tunnel results were then used to determine the case study stability derivative values, and hence it used to calculate the roots of the characteristic equation for both longitudinal and lateral motions. Finally, the characteristic equation roots were found and discussed in all possible cases.
Abstract: Quad Flat No-Lead (QFN) packages have become very popular for turners, converters and audio amplifiers, among others applications, needing efficient power dissipation in small footprints. Since semiconductor junction temperature (TJ) is a critical parameter in the product quality. And to ensure that die temperature does not exceed the maximum allowable TJ, a thermal analysis conducted in an earlier development phase is essential to avoid repeated re-designs process with huge losses in cost and time. A simulation tool capable to estimate die temperature of components with QFN package was developed. Allow establish a non-empirical way to define an acceptance criterion for amount of voids in solder interface between its exposed pad and Printed Circuit Board (PCB) to be applied during industrialization process, and evaluate the impact of PCB designs parameters. Targeting PCB layout designer as an end user for the application, a user-friendly interface (GUI) was implemented allowing user to introduce design parameters in a convenient and secure way and hiding all the complexity of finite element simulation process. This cost effective tool turns transparent a simulating process and provides useful outputs after acceptable time, which can be adopted by PCB designers, preventing potential risks during the design stage and make product economically efficient by not oversizing it. This article gathers relevant information related to the design and implementation of the developed tool, presenting a parametric study conducted with it. The simulation tool was experimentally validated using a Thermal-Test-Chip (TTC) in a QFN open-cavity, in order to measure junction temperature (TJ) directly on the die under controlled and knowing conditions. Providing a short overview about standard thermal solutions and impacts in exposed pad packages (i.e. QFN), accurately describe the methods and techniques that the system designer should use to achieve optimum thermal performance, and demonstrate the effect of system-level constraints on the thermal performance of the design.
Abstract: Compressor fans in modern aircraft engines are of considerate importance, as they provide majority of thrust required by the aircraft. Their challenging environment is frequently subjected to non-uniform inflow conditions. These conditions could be either due to the flight operating requirements such as take-off and landing, wake interference from aircraft fuselage or cross-flow wind conditions. So, in highly maneuverable flights regimes of fighter aircrafts affects the overall performance of an engine. Since the flow in compressor of an aircraft application is highly sensitive because of adverse pressure gradient due to different flow orientations of the aircraft. Therefore, it is prone to unstable operations. This paper presents the study that focuses on axial compressor response to inlet flow orientations for the range of angles as 0 to 15 degrees. For this purpose, NASA Rotor-37 was taken and CFD mesh was developed. The compressor characteristics map was generated for the design conditions of pressure ratio of 2.106 with the rotor operating at rotational velocity of 17188.7 rpm using CFD simulating environment of ANSYS-CFX®. The grid study was done to see the effects of mesh upon computational solution. Then, the mesh giving the best results, (when validated with the available experimental NASA’s results); was used for further distortion analysis. The flow in the inlet nozzle was given angle orientations ranging from 0 to 15 degrees. The CFD results are analyzed and discussed with respect to stall margin and flow separations due to induced distortions.
Abstract: Wireless Body Area Network (WBAN) is a short-range
wireless communication around human body for various applications
such as wearable devices, entertainment, military, and especially
medical devices. WBAN attracts the attention of continuous health
monitoring system including diagnostic procedure, early detection of
abnormal conditions, and prevention of emergency situations.
Compared to cellular network, WBAN system is more difficult to
control inter- and inner-cell interference due to the limited power,
limited calculation capability, mobility of patient, and
non-cooperation among WBANs.
In this paper, we compare the performance of resource allocation
scheme based on several Pseudo Orthogonal Codewords (POCs) to
mitigate inter-WBAN interference. Previously, the POCs are widely
exploited for a protocol sequence and optical orthogonal code. Each
POCs have different properties of auto- and cross-correlation and
spectral efficiency according to its construction of POCs. To identify
different WBANs, several different pseudo orthogonal patterns based
on POCs exploits for resource allocation of WBANs. By simulating
these pseudo orthogonal resource allocations of WBANs on
MATLAB, we obtain the performance of WBANs according to
different POCs and can analyze and evaluate the suitability of POCs
for the resource allocation in the WBANs system.
Abstract: This paper details the progress made in the development of the different state-of-the-art aerodynamic tools for the analysis of vertical axis wind turbines including the flow simulation around the blade, viscous flow, stochastic wind, and dynamic stall effects. The paper highlights the capabilities of the developed wind turbine aerodynamic codes over the last thirty years which are currently being used in North America and Europe by Sandia Laboratories, FloWind, IMST Marseilles, and Hydro-Quebec among others. The aerodynamic codes developed at Ecole Polytechnique de Montreal, Canada, represent valuable tools for simulating the flow around wind turbines including secondary effects. Comparison of theoretical results with experimental data have shown good agreement. The strength of the aerodynamic codes based on Double-Multiple Stream tube model (DMS) lies in its simplicity, accuracy, and ability to analyze secondary effects that interfere with wind turbine aerodynamic calculations.
Abstract: Makishima and Mackenzie model was used to
simulation of acoustic properties (longitudinal and shear ultrasonic
wave velocities, elastic moduli theoretically for many tellurite and
borate glasses. The model was proposed mainly depending on the
values of the experimentally measured density, which are obtained
before. In this search work, we are trying to obtain the values of
densities of amorphous glasses (as the density depends on the
geometry of the network structure of these glasses). In addition, the
problem of simulating the slope of linear regression between the
experimentally determined bulk modulus and the product of packing
density and experimental Young's modulus, were solved in this
search work. The results showed good agreement between the
experimentally measured values of densities and both ultrasonic wave
velocities, and those theoretically determined.
Abstract: Hydrologic models are increasingly used as tools to
predict stormwater quantity and quality from urban catchments.
However, due to a range of practical issues, most models produce
gross errors in simulating complex hydraulic and hydrologic systems.
Difficulty in finding a robust approach for model calibration is one of
the main issues. Though automatic calibration techniques are
available, they are rarely used in common commercial hydraulic and
hydrologic modelling software e.g. MIKE URBAN. This is partly
due to the need for a large number of parameters and large datasets in
the calibration process. To overcome this practical issue, a
framework for automatic calibration of a hydrologic model was
developed in R platform and presented in this paper. The model was
developed based on the time-area conceptualization. Four calibration
parameters, including initial loss, reduction factor, time of
concentration and time-lag were considered as the primary set of
parameters. Using these parameters, automatic calibration was
performed using Approximate Bayesian Computation (ABC). ABC is
a simulation-based technique for performing Bayesian inference
when the likelihood is intractable or computationally expensive to
compute. To test the performance and usefulness, the technique was
used to simulate three small catchments in Gold Coast. For
comparison, simulation outcomes from the same three catchments
using commercial modelling software, MIKE URBAN were used.
The graphical comparison shows strong agreement of MIKE URBAN
result within the upper and lower 95% credible intervals of posterior
predictions as obtained via ABC. Statistical validation for posterior
predictions of runoff result using coefficient of determination (CD),
root mean square error (RMSE) and maximum error (ME) was found
reasonable for three study catchments. The main benefit of using
ABC over MIKE URBAN is that ABC provides a posterior
distribution for runoff flow prediction, and therefore associated
uncertainty in predictions can be obtained. In contrast, MIKE
URBAN just provides a point estimate. Based on the results of the
analysis, it appears as though ABC the developed framework
performs well for automatic calibration.
Abstract: This paper discusses the applicability of the numerical model for a damage prediction method of the accidental hydrogen explosion occurring in a hydrogen facility. The numerical model was based on an unstructured finite volume method (FVM) code “NuFD/FrontFlowRed”. For simulating unsteady turbulent combustion of leaked hydrogen gas, a combination of Large Eddy Simulation (LES) and a combustion model were used. The combustion model was based on a two scalar flamelet approach, where a G-equation model and a conserved scalar model expressed a propagation of premixed flame surface and a diffusion combustion process, respectively. For validation of this numerical model, we have simulated the previous two types of hydrogen explosion tests. One is open-space explosion test, and the source was a prismatic 5.27 m3 volume with 30% of hydrogen-air mixture. A reinforced concrete wall was set 4 m away from the front surface of the source. The source was ignited at the bottom center by a spark. The other is vented enclosure explosion test, and the chamber was 4.6 m × 4.6 m × 3.0 m with a vent opening on one side. Vent area of 5.4 m2 was used. Test was performed with ignition at the center of the wall opposite the vent. Hydrogen-air mixtures with hydrogen concentrations close to 18% vol. were used in the tests. The results from the numerical simulations are compared with the previous experimental data for the accuracy of the numerical model, and we have verified that the simulated overpressures and flame time-of-arrival data were in good agreement with the results of the previous two explosion tests.
Abstract: Cochlear Implantation (CI) which became a routine
procedure for the last decades is an electronic device that provides a
sense of sound for patients who are severely and profoundly deaf.
The optimal success of this implantation depends on the electrode
technology and deep insertion techniques. However, this manual
insertion procedure may cause mechanical trauma which can lead to
severe destruction of the delicate intracochlear structure.
Accordingly, future improvement of the cochlear electrode implant
insertion needs reduction of the excessive force application during
the cochlear implantation which causes tissue damage and trauma.
This study is examined tool-tissue interaction of large prototype scale
digit embedded with distributive tactile sensor based upon cochlear
electrode and large prototype scale cochlea phantom for simulating
the human cochlear which could lead to small scale digit
requirements. The digit, distributive tactile sensors embedded with
silicon-substrate was inserted into the cochlea phantom to measure
any digit/phantom interaction and position of the digit in order to
minimize tissue and trauma damage during the electrode cochlear
insertion. The digit have provided tactile information from the digitphantom
insertion interaction such as contact status, tip penetration,
obstacles, relative shape and location, contact orientation and
multiple contacts. The tests demonstrated that even devices of such a
relative simple design with low cost have potential to improve
cochlear implant surgery and other lumen mapping applications by
providing tactile sensory feedback information and thus controlling
the insertion through sensing and control of the tip of the implant
during the insertion. In that approach, the surgeon could minimize the
tissue damage and potential damage to the delicate structures within
the cochlear caused by current manual electrode insertion of the
cochlear implantation. This approach also can be applied to other
minimally invasive surgery applications as well as diagnosis and path
navigation procedures.
Abstract: This paper presents the results of a study on the
influence of varying percentages of rock bridges along a basal surface
defining a biplanar failure mode. A pseudo-coupled-hydromechanical
brittle fracture analysis is adopted using the state-of-the-art code
Slope Model. Model results show that rock bridge failure is strongly
influenced by the incorporation of groundwater pressures. The
models show that groundwater pressure can promote total failure of a
5% rock bridge along the basal surface. Once the percentage of the
rock bridges increases to 10 and 15%, although, the rock bridges are
broken, full interconnection of the surface defining the basal surface
of the biplanar mode does not occur. Increased damage is caused
when the rock bridge is located at the daylighting end of the basal
surface in proximity to the blast damage zone. As expected, some
cracking damage is experienced in the blast damage zone, where
properties representing a good quality controlled damage blast
technique were assumed. Model results indicate the potential increase
of permeability towards the blast damage zone.
Abstract: The Petri nets are the first standard for business
process modeling. Most probably, it is one of the core reasons why
all new standards created afterwards have to be so reformed as to
reach the stage of mapping the new standard onto Petri nets. The paper presents a business process repository based on a
universal database. The repository provides the possibility the data
about a given process to be stored in three different ways. Business
process repository is developed with regard to the reformation of a
given model to a Petri net in order to be easily simulated. Two different techniques for business process simulation based on
Petri nets - Yasper and Woflan are discussed. Their advantages and
drawbacks are outlined. The way of simulating business process
models, stored in the Business process repository is shown.
Abstract: Lateral Geniculate Nucleus (LGN) is the relay center
in the visual pathway as it receives most of the input information
from retinal ganglion cells (RGC) and sends to visual cortex. Low
threshold calcium currents (IT) at the membrane are the unique
indicator to characterize this firing functionality of the LGN neurons
gained by the RGC input. According to the LGN functional
requirements such as functional mapping of RGC to LGN, the
morphologies of the LGN neurons were developed. During the
neurological disorders like glaucoma, the mapping between RGC and
LGN is disconnected and hence stimulating LGN electrically using
deep brain electrodes can restore the functionalities of LGN. A
computational model was developed for simulating the LGN neurons
with three predominant morphologies each representing different
functional mapping of RGC to LGN. The firings of action potentials
at LGN neuron due to IT were characterized by varying the
stimulation parameters, morphological parameters and orientation. A
wide range of stimulation parameters (stimulus amplitude, duration
and frequency) represents the various strengths of the electrical
stimulation with different morphological parameters (soma size,
dendrites size and structure). The orientation (0-1800) of LGN
neuron with respect to the stimulating electrode represents the angle
at which the extracellular deep brain stimulation towards LGN
neuron is performed. A reduced dendrite structure was used in the
model using Bush–Sejnowski algorithm to decrease the
computational time while conserving its input resistance and total
surface area. The major finding is that an input potential of 0.4 V is
required to produce the action potential in the LGN neuron which is
placed at 100 μm distance from the electrode. From this study, it can
be concluded that the neuroprostheses under design would need to
consider the capability of inducing at least 0.4V to produce action
potentials in LGN.
Abstract: Introduction: The process to build a better safety
culture, methods of error analysis, and preventive measures, starts
with an understanding of the effects when human factors engineering
refer to remote microscopic diagnosis in surgery and specially in
organ transplantation for the remote evaluation of the grafts. It has
been estimated that even in well-organized transplant systems an
average of 8% to 14% of the grafts (G) that arrive at the recipient
hospitals may be considered as diseased, injured, damaged or
improper for transplantation. Digital microscopy adds information on
a microscopic level about the grafts in Organ Transplant (OT), and
may lead to a change in their management. Such a method will
reduce the possibility that a diseased G, will arrive at the recipient
hospital for implantation. Aim: Ergonomics of Digital Microscopy
(DM) based on virtual slides, on Telemedicine Systems (TS) for
Tele-Pathological (TPE) evaluation of the grafts (G) in organ
transplantation (OT). Material and Methods: By experimental
simulation, the ergonomics of DM for microscopic TPE of Renal
Graft (RG), Liver Graft (LG) and Pancreatic Graft (PG) tissues is
analyzed. In fact, this corresponded to the ergonomics of digital
microscopy for TPE in OT by applying Virtual Slide (VS) system for
graft tissue image capture, for remote diagnoses of possible
microscopic inflammatory and/or neoplastic lesions. Experimentation
included: a. Development of an OTE-TS similar Experimental
Telemedicine System (Exp.-TS), b. Simulation of the integration of
TS with the VS based microscopic TPE of RG, LG and PG applying
DM. Simulation of the DM based TPE was performed by 2
specialists on a total of 238 human Renal Graft (RG), 172 Liver Graft
(LG) and 108 Pancreatic Graft (PG) tissues digital microscopic
images for inflammatory and neoplastic lesions on four electronic
spaces of the four used TS. Results: Statistical analysis of specialist‘s
answers about the ability to diagnose accurately the diseased RG, LG
and PG tissues on the electronic space among four TS (A,B,C,D)
showed that DM on TS for TPE in OT is elaborated perfectly on the
ES of a Desktop, followed by the ES of the applied Exp.-TS. Tablet
and Mobile-Phone ES seem significantly risky for the application of
DM in OT (p
Abstract: In this study, the commercial finite element software
ABAQUS was used to develop a three-dimensional nonlinear finite
element model capable of simulating the pull-out test of reinforcing
bars from underwater concrete. The results of thirty-two pull-out tests
that have different parameters were implemented in the software to
study the effect of the concrete cover, the bar size, the use of stirrups,
and the compressive strength of concrete. The interaction properties used in the model provided accurate
results in comparison with the experimental bond-slip results, thus
the model has successfully simulated the pull-out test. The results of
the finite element model are used to better understand and visualize
the distribution of stresses in each component of the model, and to
study the effect of the various parameters used in this study including
the role of the stirrups in preventing the stress from reaching to the
sides of the specimens.
Abstract: Since the last decade, there has been a rapid growth in
digital multimedia, such as high-resolution media files and threedimentional
movies. Hence, there is a need for large digital storage
such as Hard Disk Drive (HDD). As such, users expect to have a
quieter HDD in their laptop. In this paper, a jury test has been
conducted on a group of 34 people where 17 of them are students
who are the potential consumer, and the remaining are engineers who
know the HDD. A total 13 HDD sound samples have been selected
from over hundred HDD noise recordings. These samples are
selected based on an agreed subjective feeling. The samples are
played to the participants using head acoustic playback system, which
enabled them to experience as similar as possible the same
environment as have been recorded. Analysis has been conducted and
the obtained results have indicated different group has different
perception over the noises. Two neural network-based acoustic
annoyance models are established based on back propagation neural
network. Four psychoacoustic metrics, loudness, sharpness,
roughness and fluctuation strength, are used as the input of the
model, and the subjective evaluation results are taken as the output.
The developed models are reasonably accurate in simulating both
training and test samples.
Abstract: This paper describes how to dimension the electric
components of a 48V hybrid system considering real customer use.
Furthermore, it provides information about savings in energy and
CO2 emissions by a customer-tailored 48V hybrid. Based on measured customer profiles, the electric units such as the
electric motor and the energy storage are dimensioned. Furthermore,
the CO2 reduction potential in real customer use is determined
compared to conventional vehicles. Finally, investigations are carried
out to specify the topology design and preliminary considerations in
order to hybridize a conventional vehicle with a 48V hybrid system.
The emission model results from an empiric approach also taking into
account the effects of engine dynamics on emissions. We analyzed
transient engine emissions during representative customer driving
profiles and created emission meta models. The investigation showed
a significant difference in emissions when simulating realistic
customer driving profiles using the created verified meta models
compared to static approaches which are commonly used for vehicle
simulation.
Abstract: The localization information is crucial for the
operation of WSN. There are principally two types of localization
algorithms. The Range-based localization algorithm has strict
requirements on hardware, thus is expensive to be implemented in
practice. The Range-free localization algorithm reduces the hardware
cost. However, it can only achieve high accuracy in ideal scenarios.
In this paper, we locate unknown nodes by incorporating the
advantages of these two types of methods. The proposed algorithm
makes the unknown nodes select the nearest anchor using the
Received Signal Strength Indicator (RSSI) and choose two other
anchors which are the most accurate to achieve the estimated
location. Our algorithm improves the localization accuracy compared
with previous algorithms, which has been demonstrated by the
simulating results.
Abstract: The LSTF experiment simulating the SGTR accident at
the Mihama Unit-2 reactor is analyzed using the RELAP5/MOD3.3
code. In the accident, and thus in the experiment, the ECC water was
injected not only into the cold legs but into the upper plenum. Overall
transients during the experiment such as pressures and fluid
temperatures are simulated well by the code. The cold-leg fluid
temperatures are shown to decrease if the upper plenum injection
system is connected to the cold leg. It is found that the cold-leg fluid
temperatures also decrease if the upper-plenum injection is not used
and the cold-leg injection alone is actuated.
Abstract: The Northeast China (NEC) was the most important
agriculture areas and known as the Golden-Maize-Belt. Based on
observed crop data and crop model, we design four simulating
experiments and separate relative impacts and contribution under
climate change, planting date shift, and varieties change as well
change of varieties and planting date. Without planting date and
varieties change, maize yields had no significant change trend at
Hailun station located in the north of NEC, and presented significant
decrease by 0.2 - 0.4 t/10a at two stations, which located in the middle
and the south of NEC. With planting date change, yields showed a
significant increase by 0.09 - 0.47 t/10a. With varieties change, maize
yields had significant increase by 1.8~ 1.9 t/10a at Hailun and Huadian
stations, but a non-significant and low increase by 0.2t /10a at Benxi
located in the south of NEC. With change of varieties and planting
date, yields presented a significant increasing by 0.53- 2.0 t/10a. Their
contribution to yields was -25% ~ -55% for climate change, 15% ~
35% for planting date change, and 20% ~110% for varieties change as
well 30% ~135% for varieties with planting date shift. It found that
change in varieties and planting date were highest yields and were
responsible for significant increases in maize yields, varieties was
secondly, and planting date was thirdly. It found that adaptation in
varieties and planting date greatly improved maize yields, and
increased yields annual variability. The increase of contribution with
planting date and varieties change in 2000s was lower than in 1990s.
Yields with the varieties change and yields with planting date and
varieties change all showed a decreasing trend at Huadian and Benxi
since 2002 or so. It indicated that maize yields increasing trend
stagnated in the middle and south of NEC, and continued in the north
of NEC.
Abstract: In this paper, we explore the macroeconomic effects
of the European Single Market on Austria by simulating the
McKibbin-Sachs Global Model. Global interdependences and the
impact of long-run effects on short-run adjustments are taken into
account. We study the sensitivity of the results with respect to
different assumptions concerning monetary and fiscal policies for the
countries and regions of the world economy. The consequences of
different assumptions about budgetary policies in Austria are also
investigated. The simulation results are contrasted with ex-post
evaluations of the actual impact of Austria’s membership in the
Single Market. As a result, it can be concluded that the Austrian
participation in the European Single Market entails considerable
long-run gains for the Austrian economy with nearly no adverse sideeffects
on any macroeconomic target variable.