Abstract: This study focuses on the problem of collapsed buildings within the city of Douala over the past ten years, and more precisely within the period from 2011 to 2020. It was carried out in a bid to ascertain the real causes of this phenomenon, which has become recurrent in the leading economic city of Cameroon. To achieve this, it was first necessary to review some works dealing with construction materials and technology as well as some case histories of structural collapse within the city. Thereafter, a statistical study was carried out on the results obtained. It was found that the causes of building collapses in the city of Douala are: Neglect of administrative procedures, use of poor quality materials, poor composition and confectioning of concrete, lack of Geotechnical study, lack of structural analysis and design, corrosion of the reinforcement bars, poor maintenance in buildings, and other causes. Out of the 46 cases of failure and collapse of buildings within the city of Douala, 7 of these were identified to have had no geotechnical study carried out, giving a percentage of 15.22%. It was also observed that out of the 46 cases of structural failure, 6 were as a result of lack of proper structural analysis and design giving a percentage of 13.04%. Subsequently, recommendations and suggestions are made in a bid to placing particular emphasis on the choice of materials, the manufacture and casting of concrete as well as the placement of the required reinforcements. All this guarantees the stability of a building.
Abstract: The floor beams of steel buildings, cold-formed steel
floor joists in particular, often require large web openings, which may
affect their shear capacities. A cost effective way to mitigate the
detrimental effects of such openings is to weld/fasten reinforcements.
A difficulty associated with an experimental investigation to establish
suitable reinforcement schemes for openings in shear zone is that
moment always coexists with the shear, and thus, it is impossible to
create pure shear state in experiments, resulting in moment
influenced results. However, Finite Element Method (FEM) based
analysis can be conveniently used to investigate the pure shear
behaviour of webs including webs with reinforced openings. This
paper presents the details associated with the finite element analysis
of thick/thin-plates (representing the web of hot-rolled steel beam,
and the web of a cold-formed steel member) having a large
reinforced opening. The study considered simply-supported
rectangular plates subjected to in-plane shear loadings until failure
(including post-buckling behaviour). The plate was modelled using
geometrically non-linear quadrilateral shell elements, and non-linear
stress-strain relationship based on experiments. Total Langrangian
with large displacement/small strain formulation was used for such
analyses. The model also considered the initial geometric
imperfections. This study considered three reinforcement schemes,
namely, flat, lip, and angle reinforcements. This paper discusses the
modelling considerations and presents the results associated with the
various reinforcement schemes under consideration.
Abstract: Geopolymer concretes are new class of construction
materials that have emerged as an alternative to Ordinary Portland
cement concrete. Considerable researches have been carried out on
material development of geopolymer concrete; however, a few studies
have been reported on the structural use of them. This paper presents
the bond behaviors of reinforcement embedded in fly ash based
geopolymer concrete. The development lengths of reinforcement for
various compressive strengths of concrete, 20, 30 and 40 MPa, and
reinforcement diameters, 10, 16 and 25 mm, are investigated. Total 27
specimens were manufactured and pull-out test according to EN 10080
was applied to measure bond strength and slips between concrete and
reinforcements. The average bond strengths decreased from 23.06MPa
to 17.26 MPa, as the diameters of reinforcements increased from
10mm to 25mm. The compressive strength levels of geopolymer
concrete showed no significant influence on bond strengths in this
study. Also, the bond-slip relations between geopolymer concrete and
reinforcement are derived using non-linear regression analysis for
various experimental conditions.
Abstract: Aluminum hybrid reinforcement technology is a
response to the dynamic ever increasing service requirements of such
industries as transportation, aerospace, automobile, marine, etc. It is
unique in that it offers a platform of almost unending combinations of
materials to produce various hybrid composites. This article reviews
the studies carried out on various combinations of aluminum hybrid
composite and the effects on mechanical, physical and chemical
properties. It is observed that the extent of enhancement of these
properties of hybrid composites is strongly dependent on the nature
of the reinforcement, its hardness, particle size, volume fraction,
uniformity of dispersion within the matrix and the method of hybrid
production.
Abstract: Metal matrix composites (MMCs) have gained a
considerable interest in the last three decades. Conventional powder
metallurgy production route often involves the addition of reinforcing
phases into the metal matrix directly, which leads to poor wetting
behavior between ceramic phase and metal matrix and the
segregation of reinforcements. The commonly used elements for
ceramic phase formation in iron based MMCs are Ti, Nb, Mo, W, V
and C, B. The aim of the present paper is to investigate the effect of
sintering temperature and V-B addition on densification, phase
development, microstructure, and hardness of Fe–V-B composites
(Fe-(5-10) wt. %B – 25 wt. %V alloys) prepared by powder
metallurgy process. Metal powder mixes were pressed uniaxial and
sintered at different temperatures (ranging from 1300 to 1400ºC) for
1h. The microstructure of the (V, B) Fe composites was studied with
the help of high magnification optical microscope and XRD.
Experimental results show that (V, B) Fe composites can be produced
by conventional powder metallurgy route.
Abstract: This paper presents a comparative study of static analysis procedure for seismic performance based on UBC-1997 and SBC-301-2007(Saudi Arabia). These building codes define different ductility classes and corresponding response reduction factors based on material, configuration and detailing of reinforcements. Codes differ significantly in specifying the procedures to estimate base shear, drift and effective stiffness of structural members. One of the major improvements made in new SBC (based on IBC-2003) is ground motion parameters used for seismic design. In old SBC (based on UBC) maps have been based on seismic zones. However new SBC provide contour maps giving spectral response quantities. In this approach, a case study of RC frame building located in two different cities and with different ductility classes has been performed. Moreover, equivalent static method based on SBC-301 and UBC-1997 is used to explore the variation in results based on two codes, particularly design base shear, lateral loads and story drifts.