Abstract: A model predictive controller based on recursive learning is proposed. In this SISO adaptive controller, a model is automatically updated using simple recursive equations. The identified models are then stored in the memory to be re-used in the future. The decision for model update is taken based on a new control performance index. The new controller allows the use of simple linear model predictive controllers in the control of nonlinear time varying processes.
Abstract: In this paper, we present a vertical nanowire thin film transistor with gate-all-around architecture, fabricated using CMOS compatible processes. A novel method of fabricating polysilicon vertical nanowires of diameter as small as 30 nm using wet-etch is presented. Both n-type and p-type vertical poly-silicon nanowire transistors exhibit superior electrical characteristics as compared to planar devices. On a poly-crystalline nanowire of 30 nm diameter, high Ion/Ioff ratio of 106, low drain-induced barrier lowering (DIBL) of 50 mV/V, and low sub-threshold slope SS~100mV/dec are demonstrated for a device with channel length of 100 nm.
Abstract: The state of melt viscosity in injection process is significantly influenced by the setting parameters due to that the shear rate of injection process is higher than other processes. How to determine plastic melt viscosity during injection process is important to understand the influence of setting parameters on the melt viscosity. An apparatus named as pressure sensor bushing (PSB) module that is used to evaluate the melt viscosity during injection process is developed in this work. The formulations to coupling melt viscosity with fill time and injection pressure are derived and then the melt viscosity is determined. A test mold is prepared to evaluate the accuracy on viscosity calculations between the PSB module and the conventional approaches. The influence of melt viscosity on the tensile strength of molded part is proposed to study the consistency of injection quality.
Abstract: Optical emission based on excitonic scattering processes becomes important in dense exciton systems in which the average distance between excitons is of the order of a few Bohr radii but still below the exciton screening threshold. The phenomena due to interactions among excited states play significant role in the emission near band edge of the material. The theory of two-exciton collisions for GaAs/AlGaAs quantum well systems is a mild attempt to understand the physics associated with the optical spectra due to excitonic scattering processes in these novel systems. The four typical processes considered give different spectral shape, peak position and temperature dependence of the emission spectra. We have used the theory of scattering together with the second order perturbation theory to derive the radiative power spontaneously emitted at an energy ħω by these processes. The results arrived at are purely qualitative in nature. The intensity of emitted light in quantum well systems varies inversely to the square of temperature, whereas in case of bulk materials it simply decreases with the temperature.
Abstract: Nowadays, the demand for high product quality
focuses extensive attention to the quality of machined surface. The
(CNC) milling machine facilities provides a wide variety of
parameters set-up, making the machining process on the glass
excellent in manufacturing complicated special products compared to
other machining processes. However, the application of grinding
process on the CNC milling machine could be an ideal solution to
improve the product quality, but adopting the right machining
parameters is required. In glass milling operation, several machining
parameters are considered to be significant in affecting surface
roughness. These parameters include the lubrication pressure, spindle
speed, feed rate and depth of cut. In this research work, a fuzzy logic
model is offered to predict the surface roughness of a machined
surface in glass milling operation using CBN grinding tool. Four
membership functions are allocated to be connected with each input
of the model. The predicted results achieved via fuzzy logic model
are compared to the experimental result. The result demonstrated
settlement between the fuzzy model and experimental results with the
93.103% accuracy.
Abstract: Trust is essential for further and wider acceptance of
contemporary e-services. It was first addressed almost thirty years
ago in Trusted Computer System Evaluation Criteria standard by
the US DoD. But this and other proposed approaches of that
period were actually solving security. Roughly some ten years ago,
methodologies followed that addressed trust phenomenon at its core,
and they were based on Bayesian statistics and its derivatives, while
some approaches were based on game theory. However, trust is a
manifestation of judgment and reasoning processes. It has to be dealt
with in accordance with this fact and adequately supported in cyber
environment. On the basis of the results in the field of psychology
and our own findings, a methodology called qualitative algebra has
been developed, which deals with so far overlooked elements of trust
phenomenon. It complements existing methodologies and provides a
basis for a practical technical solution that supports management of
trust in contemporary computing environments. Such solution is also
presented at the end of this paper.
Abstract: Water is the main component of biological processes.
Water management is important to obtain higher productivity. In this
study, some of the yield components were investigated together with
different drought levels. Four chickpea genotypes (CDC Frontier,
CDC Luna, Sawyer and Sierra) were grown in pots with 3 different
irrigation levels (a dose of 17.5 ml, 35 ml and 70 ml for each pot per
day) after three weeks from sowing. In the research, flowering, pod
set, pod per plant, fertile pod, double seed/pod, stem diameter, plant
weight, seed per plant, 1000 seed weight, seed diameter, vegetation
length and weekly plant height were measured. Consequently,
significant differences were observed on all the investigated
characteristics owing to genotypes (except double seed/pod and stem
diameter), water levels (except first pod, seed weight and height on
3rd week) and genotype x water level interaction (except first pod,
double seed/pod, seed weight and height).
Abstract: Today many countries have the ambitious purposes of long-term and continuous development: constant growth of competitiveness, maintenance of a high standard of living of the population, leadership in the world market. One of the best possible ways of achievement of these purposes is a transition of the countries to innovative economy. The paper presents the analyses of problems of forming of innovative receptivity to innovations and creation of «innovative society». Creation of an innovative culture in a society and increase of the level of prestige of innovative activity are the best ways of developing of innovative processes. The base of the analysis is a comparing of Russia and different developed countries according to the level of some indictors of innovative activity.1
Abstract: In spite of the advent of new materials, clay bricks
remain, arguably, the most popular construction materials today.
Nevertheless the low cost and versatility of clay bricks cannot always
be associated with high environmental and sustainable values,
especially in terms of raw material sources and manufacturing
processes. At the same time, the worldwide agricultural footprint is
fast growing, with vast agricultural land cultivation and active
expansion of the agro-based industry. The resulting large quantities of
agricultural wastes, unfortunately, are not always well managed or
utilised. These wastes can be recycled, such as by retrieving fibres
from disposed leaves and fruit bunches, and then incorporated in
brick-making. This way the clay bricks are made a 'greener' building
material and the discarded natural wastes can be reutilised, avoiding
otherwise wasteful landfill and harmful open incineration. This study
examined the physical and mechanical properties of clay bricks made
by adding two natural fibres to a clay-water mixture, with baked and
non-baked conditions. The fibres were sourced from pineapple leaves
(PF) and oil palm fruit bunch (OF), and added within the range of
0.25-0.75 %. Cement was added as a binder to the mixture at 5-15 %.
Although the two fibres had different effects on the bricks produced,
cement appeared to dominate the compressive strength. The
non-baked bricks disintegrated when submerged in water, while the
baked ones displayed cement-dependent characteristics in
water-absorption and density changes. Interestingly, further increase
in fibre content did not cause significant density decrease in both the
baked and non-baked bricks.
Abstract: Atmospheric plasma is emerging as a promising
technology for many industrial sectors, because of its ecological and
economic advantages respect to the traditional production processes.
For textile industry, atmospheric plasma is becoming a valid
alternative to the conventional wet processes, but the plasma
machines realized so far do not allow the treatment of fibrous
mechanically weak material.
Novel atmospheric plasma machine for industrial applications,
developed by VenetoNanotech SCpA in collaboration with Italian
producer of corona equipment ME.RO SpA is presented. The main
feature of this pre-industrial scale machine is the possibility of the inline
plasma treatment of delicate fibrous substrates such as fibre
sleeves, for example wool tops, cotton fibres, polymeric tows,
mineral fibers and so on, avoiding burnings and disruption of the
faint materials.
Abstract: In the given article the creative arts is being
investigated in the modern era and from the aspect of the artistic
interrelationship, having created by the character of his personality
and as the viewer. A study in the identity formation terms, the
definition of its being unique, unity and similarity as a global issue of
the XXI century has been conducted by the analyzing the definitions
which characterize the human nature in the arts. Spiritual universality
and human existence have been considered in the art system as a
human who is a creator, as the man hero and as the character who is
the recipient as well as the analyses which have been conducted
along with the worldwide cultural and historical processes.
Abstract: Model Predictive Control (MPC) is an established control
technique in a wide range of process industries. The reason for
this success is its ability to handle multivariable systems and systems
having input, output or state constraints. Neverthless comparing to
PID controller, the implementation of the MPC in miniaturized
devices like Field Programmable Gate Arrays (FPGA) and microcontrollers
has historically been very small scale due to its complexity in
implementation and its computation time requirement. At the same
time, such embedded technologies have become an enabler for future
manufacturing enterprisers as well as a transformer of organizations
and markets. In this work, we take advantage of these recent advances
in this area in the deployment of one of the most studied and applied
control technique in the industrial engineering. In this paper, we
propose an efficient firmware for the implementation of constrained
MPC in the performed STM32 microcontroller using interior point
method. Indeed, performances study shows good execution speed
and low computational burden. These results encourage to develop
predictive control algorithms to be programmed in industrial standard
processes. The PID anti windup controller was also implemented in
the STM32 in order to make a performance comparison with the
MPC. The main features of the proposed constrained MPC framework
are illustrated through two examples.
Abstract: The increasing industrialization and motorization of the world has led to a steep rise for the demand of petroleum-based fuels. Petroleum-based fuels are obtained from limited reserves. These finite reserves are highly concentrated in certain regions of the world. Therefore, those countries not having these resources are facing energy/foreign exchange crisis, mainly due to the import of crude petroleum. Hence, it is necessary to look for alternative fuels which can be produced from resources available locally within the country such as alcohol, biodiesel, vegetable oils etc. Biodiesel is a renewable, domestically produced fuel that has been shown to reduce particulate, hydrocarbon, and carbon monoxide emissions from combustion. In the present study an experimental investigation on emission characteristic of a liquid burner system operating on several percentage of biodiesel and gas oil is carried out. Samples of exhaust gas are analysed with Testo 350 Xl. The results show that biodiesel can lower some pollutant such as CO, CO2 and particulate matter emissions while NOx emission would increase in comparison with gas oil. The results indicate there may be benefits to using biodiesel in industrial processes.
Abstract: A sequential treatment of ozonation followed by a
Fenton or photo-Fenton process, using black light lamps (365 nm) in
this latter case, has been applied to remove a mixture of
pharmaceutical compounds and the generated by-products both in
ultrapure and secondary treated wastewater. The scientifictechnological
innovation of this study stems from the in situ
generation of hydrogen peroxide from the direct ozonation of
pharmaceuticals, and can later be used in the application of Fenton
and photo-Fenton processes. The compounds selected as models
were sulfamethoxazol and acetaminophen. It should be remarked that
the use of a second process is necessary as a result of the low
mineralization yield reached by the exclusive application of ozone.
Therefore, the influence of the water matrix has been studied in terms
of hydrogen peroxide concentration, individual compound
concentration and total organic carbon removed. Moreover, the
concentration of different iron species in solution has been measured.
Abstract: The paper presents an overview of environmental
issues that may be expected with nuclear desalination. The analysis
of coupling nuclear power with desalination plants indicates that
adverse marine impacts can be mitigated with alternative intake
designs or cooling systems. The atmospheric impact of desalination
may be greatly reduced through the coupling with nuclear power,
while maximizing the socio-economic benefit for both processes. The
potential for tritium contamination of the desalinated water was
reviewed. Experience with the systems and practices related to the
radiological quality of the product water, shows no examples of
cross-contamination. Furthermore, the indicators for the public
acceptance of nuclear desalination, as one of the most important
sustainability aspects of any such large project, show a positive trend.
From the data collected, a conclusion is made that nuclear
desalination should be supported by decision-makers.
Abstract: Complex engineering design problems consist of
numerous factors of varying criticalities. Considering fundamental features of design and inferior details alike will result in an extensive
waste of time and effort. Design parameters should be introduced gradually as appropriate based on their significance relevant to the
problem context. This motivates the representation of design parameters at multiple levels of an abstraction hierarchy. However, developing abstraction hierarchies is an area that is not well
understood. Our research proposes a novel hierarchical abstraction methodology to plan effective engineering designs and processes. It
provides a theoretically sound foundation to represent, abstract and stratify engineering design parameters and tasks according to causality and criticality. The methodology creates abstraction
hierarchies in a recursive and bottom-up approach that guarantees no
backtracking across any of the abstraction levels. The methodology consists of three main phases, representation, abstraction, and layering to multiple hierarchical levels. The effectiveness of the
developed methodology is demonstrated by a design problem.
Abstract: Independent component analysis (ICA) is a computational method for finding underlying signals or components from multivariate statistical data. The ICA method has been successfully applied in many fields, e.g. in vision research, brain imaging, geological signals and telecommunications. In this paper, we apply the ICA method to an analysis of mass spectra of oligomeric species emerged from aluminium sulphate. Mass spectra are typically complex, because they are linear combinations of spectra from different types of oligomeric species. The results show that ICA can decomposite the spectral components for useful information. This information is essential in developing coagulation phases of water treatment processes.
Abstract: Mathematical justifications are given for a simulation technique of multivariate nonGaussian random processes and fields based on Rosenblatt-s transformation of Gaussian processes. Different types of convergences are given for the approaching sequence. Moreover an original numerical method is proposed in order to solve the functional equation yielding the underlying Gaussian process autocorrelation function.
Abstract: In this research, a mathematical model for integrated evaluation of green design and green manufacturing processes is presented. To design a product, there can be alternative options to design the detailed components to fulfill the same product requirement. In the design alternative cases, the components of the product can be designed with different materials and detailed specifications. If several design alternative cases are proposed, the different materials and specifications can affect the manufacturing processes. In this paper, a new concept for integrating green design and green manufacturing processes is presented. A green design can be determined based the manufacturing processes of the designed product by evaluating the green criteria including energy usage and environmental impact, in addition to the traditional criteria of manufacturing cost. With this concept, a mathematical model is developed to find the green design and the associated green manufacturing processes. In the mathematical model, the cost items include material cost, manufacturing cost, and green related cost. The green related cost items include energy cost and environmental cost. The objective is to find the decisions of green design and green manufacturing processes to achieve the minimized total cost. In practical applications, the decision-making can be made to select a good green design case and its green manufacturing processes. In this presentation, an example product is illustrated. It shows that the model is practical and useful for integrated evaluation of green design and green manufacturing processes.
Abstract: Multi-loop (De-centralized) Proportional-Integral-
Derivative (PID) controllers have been used extensively in process
industries due to their simple structure for control of multivariable
processes. The objective of this work is to design multiple-model
adaptive multi-loop PID strategy (Multiple Model Adaptive-PID)
and neural network based multi-loop PID strategy (Neural Net
Adaptive-PID) for the control of multivariable system. The first
method combines the output of multiple linear PID controllers,
each describing process dynamics at a specific level of operation.
The global output is an interpolation of the individual multi-loop
PID controller outputs weighted based on the current value of the
measured process variable. In the second method, neural network
is used to calculate the PID controller parameters based on the
scheduling variable that corresponds to major shift in the process
dynamics. The proposed control schemes are simple in structure with
less computational complexity. The effectiveness of the proposed
control schemes have been demonstrated on the CSTR process,
which exhibits dynamic non-linearity.