Abstract: In this work, we used the single Langmuir probe to
measure the plasma density distribution in an geometrically
asymmetric capacitive coupled plasma discharge system. Because of
the frame structure of powered electrode, the plasma density was not
homogeneous in the discharge volume. It was higher under the frame,
but lower in the centre. Finite element simulation results showed a
good agreement with the experiment results. To increase the electron
density in the central volume and improve the homogeneity of the
plasma, we added an auxiliary electrode, powered by DC voltage, in
the simulation geometry. The simulation results showed that the
auxiliary electrode could alter the potential distribution and improve
the density homogeneity effectively.
Abstract: In order to realize long-lived electric propulsion
systems, we have been investigating an electrodeless plasma thruster.
In our concept, a helicon plasma is accelerated by the magnetic nozzle
for the thrusts production. In addition, the electromagnetic thrust can
be enhanced by the additional radio-frequency rotating electric field
(REF) power in the magnetic nozzle. In this study, a direct
measurement of the electromagnetic thrust and a probe measurement
have been conducted using a laboratory model of the thruster under the
condition without the REF power input. Fromthrust measurement, it is
shown that the thruster produces a sub-milli-newton order
electromagnetic thrust force without the additional REF power. The
thrust force and the density jump are observed due to the discharge
mode transition from the inductive coupled plasma to the helicon wave
excited plasma. The thermal thrust is theoretically estimated, and the
total thrust force, which is a sum of the electromagnetic and the
thermal thrust force and specific impulse are calculated to be up to 650
μN (plasma production power of 400 W, Ar gas mass flow rate of 1.0
mg/s) and 210 s (plasma production power of 400 W, Ar gas mass flow
rate of 0.2 mg/s), respectively.
Abstract: Methanol-to-olefins coupled with transformation of
coal or natural gas to methanol gives an interesting and promising way
to produce ethylene and propylene. To investigate solid concentration
in gas-solid fluidized bed for methanol-to-olefins process catalyzed by
SAPO-34, a cold model experiment system is established in this paper.
The system comprises a gas distributor in a 300mm internal diameter
and 5000mm height acrylic column, the fiber optic probe system and
series of cyclones. The experiments are carried out at ambient
conditions and under different superficial gas velocity ranging from
0.3930m/s to 0.7860m/s and different initial bed height ranging from
600mm to 1200mm. The effects of radial distance, axial distance,
superficial gas velocity, initial bed height on solid concentration in the
bed are discussed. The effects of distributor shape and porosity on
solid concentration are also discussed. The time-averaged solid
concentration profiles under different conditions are obtained.
Abstract: In this study we applied thermal lens (TL) technique
to study the effect of size on thermal diffusivity of cadmium sulphide
(CdS) nanofluid prepared by using γ-radiation method containing
particles with different sizes. In TL experimental set up a diode laser
of wavelength 514 nm and intensity stabilized He-Ne laser were used
as the excitation source and the probe beam respectively,
respectively. The experimental results showed that the thermal
diffusivity value of CdS nanofluid increases when the of particle size
increased.
Abstract: The control of commutation of switched reluctance
(SR) motor has nominally depended on a physical position detector.
The physical rotor position sensor limits robustness and increases
size and inertia of the SR drive system. The paper describes a method
to overcome these limitations by using magnetization characteristics
of the motor to indicate rotor and stator teeth overlap status. The
method is using active current probing pulses of same magnitude that
is used to simulate flux linkage in the winding being probed. A
microprocessor is used for processing magnetization data to deduce
rotor-stator teeth overlap status and hence rotor position. However,
the back-of-core saturation and mutual coupling introduces overlap
detection errors, hence that of commutation control. This paper
presents the concept of the detection scheme and the effects of backof
core saturation.
Abstract: Biochemical Oxygen Demand (BOD) is a measure of
the oxygen used in bacteria mediated oxidation of organic substances
in water and wastewater. Theoretically an infinite time is required for
complete biochemical oxidation of organic matter, but the
measurement is made over 5-days at 20 0C or 3-days at 27 0C test
period with or without dilution. Researchers have worked to further
reduce the time of measurement.
The objective of this paper is to review advancement made in
BOD measurement primarily to minimize the time and negate the
measurement difficulties. Survey of literature review in four such
techniques namely BOD-BARTTM, Biosensors, Ferricyanidemediated
approach, luminous bacterial immobilized chip method.
Basic principle, method of determination, data validation and their
advantage and disadvantages have been incorporated of each of the
methods.
In the BOD-BARTTM method the time lag is calculated for the
system to change from oxidative to reductive state. BIOSENSORS
are the biological sensing element with a transducer which produces
a signal proportional to the analyte concentration. Microbial species
has its metabolic deficiencies. Co-immobilization of bacteria using
sol-gel biosensor increases the range of substrate. In ferricyanidemediated
approach, ferricyanide has been used as e-acceptor instead
of oxygen. In Luminous bacterial cells-immobilized chip method,
bacterial bioluminescence which is caused by lux genes was
observed. Physiological responses is measured and correlated to
BOD due to reduction or emission.
There is a scope to further probe into the rapid estimation of BOD.
Abstract: Dielectric sheet perturbation to the dominant TE111
mode resonant frequency of a circular cavity is studied and presented
in this paper. The dielectric sheet, placed at the middle of the airfilled
cavity, introduces discontinuities and disturbs the configuration
of electromagnetic fields in the cavity. For fixed dimensions of cavity
and fixed thickness of the loading dielectric, the dominant resonant
frequency varies quite linearly with the permittivity of the dielectric.
This quasi-linear relationship is plotted using Maple software and
verified using 3D electromagnetic simulations. Two probes are used
in the simulation for wave excitation into and from the cavity. The
best length of probe is found to be 3 mm, giving the closest resonant
frequency to the one calculated using Maple. A total of fourteen
different dielectrics of permittivity ranging from 1 to 12.9 are tested
one by one in the simulation. The works show very close agreement
between the results from Maple and the simulation. A constant
difference of 0.04 GHz is found between the resonant frequencies
collected during simulation and the ones from Maple. The success of
this project may lead to the possibility of using the middle loaded
cavity at TE111 mode as a microwave non-destructive testing of solid
materials.
Abstract: In molecular biology, microarray technology is widely and successfully utilized to efficiently measure gene activity. If working with less studied organisms, methods to design custom-made microarray probes are available. One design criterion is to select probes with minimal melting temperature variances thus ensuring similar hybridization properties. If the microarray application focuses on the investigation of metabolic pathways, it is not necessary to cover the whole genome. It is more efficient to cover each metabolic pathway with a limited number of genes. Firstly, an approach is presented which minimizes the overall melting temperature variance of selected probes for all genes of interest. Secondly, the approach is extended to include the additional constraints of covering all pathways with a limited number of genes while minimizing the overall variance. The new optimization problem is solved by a bottom-up programming approach which reduces the complexity to make it computationally feasible. The new method is exemplary applied for the selection of microarray probes in order to cover all fungal secondary metabolite gene clusters for Aspergillus terreus.
Abstract: Methanol-to-olefins (MTO) coupled with
transformation of coal or natural gas to methanol gives an interesting
and promising way to produce ethylene and propylene. To investigate
solid concentration in gas-solid fluidized bed for methanol-to-olefins
process catalyzed by SAPO-34, a cold model experiment system is
established in this paper. The system comprises a gas distributor in a
300mm internal diameter and 5000mm height acrylic column, the
fiber optic probe system and series of cyclones. The experiments are
carried out at ambient conditions and under different superficial gas
velocity ranging from 0.3930m/s to 0.7860m/s and different initial bed
height ranging from 600mm to 1200mm. The effects of radial
distance, axial distance, superficial gas velocity, initial bed height on
solid concentration in the bed are discussed. The effects of distributor
shape and porosity on solid concentration are also discussed. The
time-averaged solid concentration profiles under different conditions
are obtained.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: The crystalline quality of the AlGaN/GaN high electron mobility transistor (HEMT) structure grown on a 200 mm silicon substrate has been investigated using UV-visible micro- Raman scattering and photoluminescence (PL). The visible Raman scattering probes the whole nitride stack with the Si substrate and shows the presence of a small component of residual in-plane stress in the thick GaN buffer resulting from a wafer bowing, while the UV micro-Raman indicates a tensile interfacial stress induced at the top GaN/AlGaN/AlN layers. PL shows a good crystal quality GaN channel where the yellow band intensity is very low compared to that of the near-band-edge transition. The uniformity of this sample is shown by measurements from several points across the epiwafer.
Abstract: Deaminated lesions were produced via nitrosative oxidation of natural nucleobases; uracul (Ura, U) from cytosine (Cyt, C), hypoxanthine (Hyp, H) from adenine (Ade, A), and xanthine (Xan, X) and oxanine (Oxa, O) from guanine (Gua, G). Such damaged nucleobases may induce mutagenic problems, so that much attentions and efforts have been poured on the revealing of their mechanisms in vivo or in vitro. In this study, we employed these deaminated lesions as useful probes for analysis of DNA-binding/recognizing proteins or enzymes. Since the pyrimidine lesions such as Hyp, Oxa and Xan are employed as analogues of guanine, their comparative uses are informative for analyzing the role of Gua in DNA sequence in DNA-protein interaction. Several DNA oligomers containing such Hyp, Oxa or Xan substituted for Gua were designed to reveal the molecular interaction between DNA and protein. From this approach, we have got useful information to understand the molecular mechanisms of the DNA-recognizing enzymes, which have not ever been observed using conventional DNA oligomer composed of just natural nucleobases.
Abstract: This paper presents the theoretical investigation of a
slotted patch antenna. The main objective of proposed work is to
obtain a large bandwidth antenna with reduced size. The antenna has
a compact size of 21.1mm x 20.25mm x 8.5mm. Two designs with
minor variation are studied which provide wide impedance
bandwidths of 24.056% and 25.63% respectively with the use of
parasitic elements when excited by a probe feed. The advantages of
this configuration are its compact size and the wide range of
frequencies covered. A parametric study is also conducted to
investigate the characteristics of the antenna under different
conditions. The measured return loss and radiation pattern indicate
the suitability of this design for WLAN applications, namely, Wi-
Max, 802.11a/b/g and ISM bands.
Abstract: Gas hydrates can agglomerate and block multiphase oil and gas pipelines when water is present at hydrate forming conditions. Using "Cold Flow Technology", the aim is to condition gas hydrates so that they can be transported as a slurry mixture without a risk of agglomeration. During the pipeline shut down however, hydrate particles may settle in bends and build hydrate plugs. An experimental setup has been designed and constructed to study the flow of such plugs at start up operations. Experiments have been performed using model fluid and model hydrate particles. The propagations of initial plugs in a bend were recorded with impedance probes along the pipe. The experimental results show a dispersion of the plug front. A peak in pressure drop was also recorded when the plugs were passing the bend. The evolutions of the plugs have been simulated by numerical integration of the incompressible mass balance equations, with an imposed mixture velocity. The slip between particles and carrier fluid has been calculated using a drag relation together with a particle-fluid force balance.
Abstract: In this paper, we probe into the traffic assignment problem by the chromosome-learning-based path finding method in simulation, which is to model the driver' behavior in the with-in-a-day process. By simply making a combination and a change of the traffic route chromosomes, the driver at the intersection chooses his next route. The various crossover and mutation rules are proposed with extensive examples.
Abstract: In this paper we study a system composed by carbon
nanotube (CNT) and bundle of carbon nanotube (BuCNT) interacting
with a specific fatty acid as molecular probe. Full system is
represented by open nanotube (or nanotubes) and the linoleic acid
(LA) relaxing due the interaction with CNT and BuCNT. The LA has
in his form an asymmetric shape with COOH termination provoking
a close BuCNT interaction mainly by van der Waals force field. The
simulations were performed by classical molecular dynamics with
standard parameterizations.
Our results show that these BuCNT and CNT are dynamically
stable and it shows a preferential interaction position with LA
resulting in three features: (i) when the LA is interacting with CNT
and BuCNT (including both termination, CH2 or COOH), the LA is
repelled; (ii) when the LA terminated with CH2 is closer to open
extremity of BuCNT, the LA is also repelled by the interaction
between them; and (iii) when the LA terminated with COOH is
closer to open extremity of BuCNT, the LA is encapsulated by the
BuCNT. These simulations are part of a more extensive work on
searching efficient selective molecular devices and could be useful to
reach this goal.
Abstract: Considering toxicity of heavy metals and their
accumulation in domestic wastes, immobilization of lead and
cadmium is envisaged inside glass-ceramics. We particularly
focused this work on calcium-rich phases embedded in a
glassy matrix.
Glass-ceramics were synthesized from glasses doped with
12 wt% and 16 wt% of PbO or CdO. They were observed and
analyzed by Electron MicroProbe Analysis (EMPA) and
Analytical Scanning Electron Microscopy (ASEM). Structural
characterization of the samples was performed by powder XRay
Diffraction.
Diopside crystals of CaMgSi2O6 composition are shown to
incorporate significant amounts of cadmium (up to 9 wt% of
CdO). Two new crystalline phases are observed with very
high Cd or Pb contents: about 40 wt% CdO for the cadmiumrich
phase and near 60 wt% PbO for the lead-rich phase. We
present complete chemical and structural characterization of
these phases. They represent a promising way for the
immobilization of toxic elements like Cd or Pb since glass
ceramics are known to propose a “double barrier" protection
(metal-rich crystals embedded in a glass matrix) against metal
release in the environment.
Abstract: In recent years, scanning probe atomic force
microscopy SPM AFM has gained acceptance over a wide spectrum
of research and science applications. Most fields focuses on physical,
chemical, biological while less attention is devoted to manufacturing
and machining aspects. The purpose of the current study is to assess
the possible implementation of the SPM AFM features and its
NanoScope software in general machining applications with special
attention to the tribological aspects of cutting tool. The surface
morphology of coated and uncoated as-received carbide inserts is
examined, analyzed, and characterized through the determination of
the appropriate scanning setting, the suitable data type imaging
techniques and the most representative data analysis parameters
using the MultiMode SPM AFM in contact mode. The NanoScope
operating software is used to capture realtime three data types
images: “Height", “Deflection" and “Friction". Three scan sizes are
independently performed: 2, 6, and 12 μm with a 2.5 μm vertical
range (Z). Offline mode analysis includes the determination of three
functional topographical parameters: surface “Roughness", power
spectral density “PSD" and “Section". The 12 μm scan size in
association with “Height" imaging is found efficient to capture every
tiny features and tribological aspects of the examined surface. Also,
“Friction" analysis is found to produce a comprehensive explanation
about the lateral characteristics of the scanned surface. Configuration
of many surface defects and drawbacks has been precisely detected
and analyzed.
Abstract: In this work the numerical simulation of transient heat
transfer in a cylindrical probe is done. An experiment was conducted
introducing a steel cylinder in a heating chamber and registering its
surface temperature along the time during one hour. In parallel, a
mathematical model was solved for one dimension transient heat
transfer in cylindrical coordinates, considering the boundary
conditions of the test. The model was solved using finite difference
method, because the thermal conductivity in the cylindrical steel bar
and the convection heat transfer coefficient used in the model are
considered temperature dependant functions, and both conditions
prevent the use of the analytical solution. The comparison between
theoretical and experimental results showed the average deviation is
below 2%. It was concluded that numerical methods are useful in
order to solve engineering complex problems. For constant k and h,
the experimental methodology used here can be used as a tool for
teaching heat transfer in mechanical engineering, using mathematical
simplified models with analytical solutions.
Abstract: Using DNA microarrays the comparative analysis of a
gene expression profiles is carried out in a liver and kidneys of pigs.
The hypothesis of a cross hybridization of one probe with different
cDNA sites of the same gene or different genes is checked up, and it
is shown, that cross hybridization can be a source of essential errors
at revealing of a key genes in organ-specific transcriptome. It is
reveald that distinctions in profiles of a gene expression are well coordinated
with function, morphology, biochemistry and histology of
these organs.