Abstract: Location-based services (LBS) exploit the known
location of a user to provide services dependent on their geographic
context and personalized needs [1].
The development and arrival of broadband mobile data networks
supported with mobile terminals equipped with new location
technologies like GPS have finally created opportunities for
implementation of LBS applications. But, from the other side,
collecting location information data in general raises privacy
concerns.
This paper presents results from two surveys of LBS acceptance in
Croatia. The first survey was administered on 181 students, and the
second extended survey involved pattern of 180 Croatian citizens.
We developed questionnaire which consists of descriptions of 15
different applications with scale which measures perceptions and
attitudes of users towards these applications.
We report the results to identify potential commercial applications
for LBS in B2C segment. Our findings suggest that some types of
applications like emergency&safety services and navigation have
significantly higher rate of acceptance than other types.
Abstract: In this paper, the bond strength of thermal spray
coatings in high speed shafts has been studied. The metallurgical and
mechanical studies has been made on the coated samples and shaft
using optical microscopy, scanning electron microscopy (SEM).
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: The objectives of this research are to produce
prototype coconut oil based solvent offset printing inks and to
analyze a basic quality of printing work derived from coconut oil
based solvent offset printing inks, by mean of bringing coconut oil
for producing varnish and bringing such varnish to produce black
offset printing inks. Then, analysis of qualities i.e. CIELAB value,
density value, and dot gain value of printing work from coconut oil
based solvent offset printing inks which printed on gloss-coated
woodfree paper weighs 130 grams were done. The research result of
coconut oil based solvent offset printing inks indicated that the
suitable varnish formulation is using 51% of coconut oil, 36% of
phenolic resin, and 14% of solvent oil 14%, while the result of
producing black offset ink displayed that the suitable formula of
printing ink is using varnish mixed with 20% of coconut oil, and the
analyzing printing work of coconut oil based solvent offset printing
inks which printed on paper, the results were as follows: CIELAB
value of black offset printing ink is at L* = 31.90, a* = 0.27, and b* =
1.86, density value is at 1.27 and dot gain value was high at mid tone
area of image area.
Abstract: Twelve lactating Etawah Crossedbred goats were used
in this study. Goat feed consisted of Cally andra callothyrsus,
Pennisetum purpureum, wheat bran and dried fermented cassava
peel. The cassava peels were fermented with a traditional culture
called “ragi tape" (mixed culture of Saccharomyces cerevisae,
Aspergillus sp, Candida, Hasnula and Acetobacter). The goats were
divided into 2 groups (Control and Treated) of six does. The
experimental diet of the Control group consisted of 70% of roughage
(fresh Callyandra callothyrsus and Pennisetum purpureum 60:40)
and 30% of wheat bran on dry matter (DM) base. In the Treated
group 30% of wheat bran was replaced with dried fermented cassava
peels. Data were statistically analyzed using analysis of variance
followed SPSS program. The concentration of HCN in fermented
cassava peel decreased to non toxic level. Nutrient composition of
dried fermented cassava peel consisted of 85.75% dry matter;
5.80% crude protein and 82.51% total digestible nutrien (TDN).
Substitution of 30% of wheat bran with dried fermented cassava peel
in the diet had no effect on dry matter and organic matter intake but
significantly (P< 0.05) decreased crude protein and TDN
consumption as well as milk yields and milk composition. The study
recommended to reduced the level of substitution to less than 30% of
concentrates in the diet in order to avoid low nutrient intake and milk
production of goats.
Abstract: Spherical shaped magnetite (Fe3O4) and Au@Fe3O4
nanoparticles were successfully synthesized from Fe electrodes
immersed in water with CTAB surfactant and HAuCl4 solution using
simple method-pulsed plasma in liquid, without the use of dopants or
special conditions for stabilization. Vibrating sample magnetometer
indicated ferromagnetic behavior of particles at room temperature with
coercivity and saturation magnetization of (Hc=105 Oe, Ms=6.83
emu/g) for Fe3O4 and (Hc=175, Ms=3.56emu/g) for Au@Fe3O4
nanoparticles. Structure and morphology of nanoparticles were
characterized by X-ray Diffraction analysis and HR-TEM
measurements. The cytotoxicity of nanoparticles was indicated using a
XTT assay to be very low (cell viability: 98-89% with Fe3O4 and
99-91% for Au@Fe3O4 NPs).
Abstract: The paper provides a discussion of the most relevant
aspects of yield curve modeling. Two classes of models are
considered: stochastic and parsimonious function based, through the
approaches developed by Vasicek (1977) and Nelson and Siegel
(1987). Yield curve estimates for Croatia are presented and their
dynamics analyzed and finally, a comparative analysis of models is
conducted.
Abstract: Given that entrepreneurship is a very significant factor of regional development, it is necessary to approach systematically the development with measures of regional politics. According to international classification The Nomenclature of Territorial Units for Statistics (NUTS II), there are three regions in Croatia. The indicators of entrepreneurial activities on the national level of Croatia are analyzed in the paper, taking into consideration the results of referent research. The level of regional development is shown based on the analysis of entrepreneurs- operations. The results of the analysis show a very unfavorable situation in entrepreneurial activities on the national level of Croatia. The origin of this situation is to be found in the surroundings with an expressed inequality of regional development, which is caused by the non-existence of a strategically directed regional policy. In this paper recommendations which could contribute to the reduction of regional inequality in Croatia, have been made.
Abstract: Natural gas flow contains undesirable solid particles,
liquid condensation, and/or oil droplets and requires reliable
removing equipment to perform filtration. Recent natural gas
processing applications are demanded compactness and reliability of
process equipment. Since conventional means are sophisticated in
design, poor in efficiency, and continue lacking robust, a supersonic
nozzle has been introduced as an alternative means to meet such
demands.
A 3-D Convergent-Divergent Nozzle is simulated using
commercial Code for pressure ratio (NPR) varies from 1.2 to 2. Six
different shapes of nozzle are numerically examined to illustrate the
position of shock-wave as such spot could be considered as a
benchmark of particle separation. Rectangle, triangle, circular,
elliptical, pentagon, and hexagon nozzles are simulated using Fluent
Code with all have same cross-sectional area.
The simple one-dimensional inviscid theory does not describe the
actual features of fluid flow precisely as it ignores the impact of
nozzle configuration on the flow properties. CFD Simulation results,
however, show that nozzle geometry influences the flow structures
including location of shock wave.
The CFD analysis predicts shock appearance when p01/pa>1.2 for
almost all geometry and locates at the lower area ratio (Ae/At).
Simulation results showed that shock wave in Elliptical nozzle has
the farthest distance from the throat among the others at relatively
small NPR. As NPR increases, hexagon would be the farthest. The
numerical result is compared with available experimental data and
has shown good agreement in terms of shock location and flow
structure.
Abstract: The aim of this paper is to present a comparative
study on two different methods for the evaluation of the equilibrium
point of a ship, core issue for designing an On Board Stability System
(OBSS) module that, starting from geometry information of a ship
hull, described by a discrete model in a standard format, and the
distribution of all weights onboard calculates the ship floating
conditions (in draught, heel and trim).
Abstract: This paper describes studies carried out to investigate
the viability of using wireless cameras as a tool in monitoring
changes in air quality. A camera is used to monitor the change in
colour of a chemically responsive polymer within view of the camera
as it is exposed to varying chemical species concentration levels. The
camera captures this image and the colour change is analyzed by
averaging the RGB values present. This novel chemical sensing
approach is compared with an established chemical sensing method
using the same chemically responsive polymer coated onto LEDs. In
this way, the concentration levels of acetic acid in the air can be
tracked using both approaches. These approaches to chemical plume
tracking have many applications for air quality monitoring.
Abstract: The case study was conducted to show the effect of milking method in goat called half day milking on the milk production and the growth of kids. Data were collected by interviewing farmers and investigating goat production in the communal goat housing from June 2008 to May 2009. The interview was conducted to collect data about goat management. The observations were conducted on 10 goats, which were selected based on the uniformity of age, number of kid born/goat and the milking method in practice. The samples were divided into two groups; those were full 3 months nursing and half day milked goats (in this group the kids were separated from goat during the previous night milking and then the kids were allowed to suck the goat during the day). The result showed that the communal goat housing had 138 goats and 25% of the farmers milked the goat. The implementation of half day milking increased the milk production significantly (P
Abstract: A numerical study on the heat transfer in the thermal
barrier coatings and the substrates of a parallel-plate enclosure is
carried out. Some of the thermal barrier coatings, such as ceramics, are
semitransparent and are of interest for high-temperature applications
where radiation effects are significant. The radiative transfer equations
and the energy equations are solved by using the discrete ordinates
method and the finite difference method. Illustrative results are
presented for temperature distributions in the coatings and the opaque
walls under various heating conditions. The results show that the
temperature distribution is more uniform in the interior portion of each
coating away from its boundary for the case with a larger average of
varying refractive index and a positive gradient of refractive index
enhances radiative transfer to the substrates.
Abstract: Urinary Tract Infections (UTI) account for an estimated 25-40% nosocomial infection, out of which 90% are associated with urinary catheter, called Catheter associated urinary tract infection (CAUTI). The microbial populations within CAUTI frequently develop as biofilms. In the present study, microbial contamination of indwelling urinary catheters was investigated. Biofilm forming ability of the isolates was determined by tissue culture plate method. Prevention of biofilm formation in the urinary catheter by Pseudomonas aeruginosa was also determined by coating the catheter with some enzymes, gentamycin and EDTA. It was found that 64% of the urinary catheters get contaminated during the course of catheterization. Of the total 6 isolates, biofilm formation was seen in 100% Pseudomonas aeruginosa and E. coli, 90% in Enterococci, 80% in Klebsiella and 66% in S. aureus. It was noted that the biofilm production by Pseudomonas was prolonged by 7 days in amylase, 8 days in protease, 6 days in lysozyme, 7days in gentamycin and 5 days in EDTA treated catheter.
Abstract: TiO2/MgO composite films were prepared by coating
the magnesium acetate solution in the pores of mesoporous TiO2
films using a dip coating method. Concentrations of magnesium
acetate solution were varied in a range of 1x10-4 – 1x10-1 M. The
TiO2/MgO composite films were characterized by scanning electron
microscopy (SEM), transmission electron microscropy (TEM),
electrochemical impedance spectroscopy(EIS) , transient voltage
decay and I-V test. The TiO2 films and TiO2/MgO composite films
were immersed in a 0.3 mM N719 dye solution. The Dye-sensitized
solar cells with the TiO2/MgO/N719 structure showed an optimal
concentration of magnesium acetate solution of 1x10-3 M resulting in
the MgO film estimated thickness of 0.0963 nm and giving the
maximum efficiency of 4.85%. The improved efficiency of dyesensitized
solar cell was due to the magnesium oxide film as the wide
band gap coating decays the electron back transfer to the triiodide
electrolyte and reduce charge recombination.
Abstract: n-CdO/p-Si heterojunction diode was fabricated using
sol-gel spin coating technique which is a low cost and easily scalable
method for preparing of semiconductor films. The structural and
morphological properties of CdO film were investigated. The X-ray
diffraction (XRD) spectra indicated that the film was of
polycrystalline nature. The scanning electron microscopy (SEM)
images indicate that the surface morphology CdO film consists of the
clusters formed with the coming together of the nanoparticles. The
electrical characterization of Au/n-CdO/p–Si/Al heterojunction diode
was investigated by current-voltage. The ideality factor of the diode
was found to be 3.02 for room temperature. The reverse current of
the diode strongly increased with illumination intensity of 100
mWcm-2 and the diode gave a maximum open circuit voltage Voc of
0.04 V and short-circuits current Isc of 9.92×10-9 A.
Abstract: Introduction applicability of high-speed cutting stock problem (CSP) is presented in this paper. Due to the orders continued coming in from various on-line ways for a professional cutting company, to stay competitive, such a business has to focus on sustained production at high levels. In others words, operators have to keep the machine running to stay ahead of the pack. Therefore, the continuous stock cutting problem with setup is proposed to minimize the cutting time and pattern changing time to meet the on-line given demand. In this paper, a novel method is proposed to solve the problem directly by using cutting patterns directly. A major advantage of the proposed method in series on-line production is that the system can adjust the cutting plan according to the floating orders. Examples with multiple items are demonstrated. The results show considerable efficiency and reliability in high-speed cutting of CSP.
Abstract: Fabrication and efficiency enhancement of non-mercury, high efficiency and green field emission lamps using carbon nano-materials such as carbon nanotubes as cathode field emitters was studied. Phosphor was coated on the ITO glass or metal substrates as the anode. The luminescence efficiency enhancement was carried out by upgrading the uniform of the emitters, improving electron and thermal conductivity of the phosphor and the optimization of the design of different cathode/anode configurations. After evaluation of the aforementioned parameters, the luminescence efficiency of the field emission lamps was raised.
Abstract: The paper presents an analysis of linkages and
structures of co-operation and their intensity like the potential for the
establishment of clusters in the Central and Eastern (Pannonian)
Croatian. Starting from the theoretical elaboration of the need for
entrepreneurs to organize through the cluster model and the terms of
their self-actualization, related to the importance of traditional values
in terms of benefits, social capital and assess where the company now
is, in order to prove the need to create their own identity in terms of
clustering. The institutional dimensions of social capital where the
public sector has the best role in creating the social structure of
clusters, and social dimensions of social capital in terms of trust,
cooperation and networking will be analyzed to what extent the trust
and coherency are present between companies in the Brod posavina
and Pozega slavonia County, expressed through the readiness of
inclusion in clusters in the NUTS II region - Central and Eastern
(Pannonian) Croatia, as a homogeneous economic entity, with
emphasis on limiting factors that stand in the way of greater
competitiveness.
Abstract: The photoluminescence (PL) at 1.55 μm from
semiconducting β-FeSi2 has attracted a noticeable interest for
silicon-based optoelectronic applications. Moreover, its high optical
absorption coefficient (higher than 105 cm-1 above 1.0 eV) allows this
semiconducting material to be used as photovoltanics devices.
A clear PL spectrum for β-FeSi2 was observed by Cu or Au coating
on Si(001). High-crystal-quality β-FeSi2 with a low-level nonradiative
center was formed on a Cu- or Au- reated Si layer. This method of
deposition can be applied to other materials requiring high crystal
quality.