Abstract: Homogeneous composites of alumina and zirconia
with a small amount of MgO (99%) were obtained for ZTA ceramic containing 0.05 wt% MgO in
1500 °C.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: The objective of this work is to explicit knowledge on the interactions between the chlorophyll-a and nine meroplankton larvae of epibenthonic fauna. The studied case is the Arraial do Cabo upwelling system, Southeastern of Brazil, which provides different environmental conditions. To assess this information a network approach based in probability estimative was used. Comparisons among the generated graphs are made in the light of different water masses, application of Shannon biodiversity index, and the closeness and betweenness centralities measurements. Our results show the main pattern among different water masses and how the core organisms belonging to the network skeleton are correlated to the main environmental variable. We conclude that the approach of complex networks is a promising tool for environmental diagnostic.
Abstract: Switched-mode converters play now a significant role in
modern society. Their operation are often crucial in various electrical
applications affecting the every day life. Therefore, the quality of
the converters needs to be reliably verified. Recent studies have
shown that the converters can be fully characterized by a set of
frequency responses which can be efficiently used to validate the
proper operation of the converters. Consequently, several methods
have been proposed to measure the frequency responses fast and
accurately. Most often correlation-based techniques have been applied.
The presented measurement methods are highly sensitive to
external errors and system nonlinearities. This fact has been often
forgotten and the necessary uncertainty analysis of the measured
responses has been neglected. This paper presents a simple approach
to analyze the noise and nonlinearities in the frequency-response
measurements of switched-mode converters. Coherence analysis is
applied to form a confidence interval characterizing the noise and
nonlinearities involved in the measurements. The presented method is
verified by practical measurements from a high-frequency switchedmode
converter.
Abstract: In this work, a characterization and modeling of
packet loss of a Voice over Internet Protocol (VoIP) communication
is developed. The distributions of the number of consecutive received
and lost packets (namely gap and burst) are modeled from the
transition probabilities of two-state and four-state model.
Measurements show that both models describe adequately the burst
distribution, but the decay of gap distribution for non-homogeneous
losses is better fit by the four-state model. The respective
probabilities of transition between states for each model were
estimated with a proposed algorithm from a set of monitored VoIP
calls in order to obtain representative minimum, maximum and
average values for both models.
Abstract: Dynamic shear test on simulated phantom can be used
to validate magnetic resonance elastography (MRE) measurements.
Phantom gel has been usually utilized for the cell culture of cartilage
and soft tissue and also been used for mechanical property
characterization using imaging systems. The viscoelastic property of
the phantom would be important for dynamic experiments and
analyses. In this study, An axisymmetric FE model is presented for
determining the dynamic shear behaviour of brain simulated phantom
using ABAQUS. The main objective of this study was to investigate
the effect of excitation frequencies and boundary conditions on shear
modulus and shear viscosity in viscoelastic media.
Abstract: Laser interferometric methods have been utilized for the measurement of natural convection heat transfer from a heated vertical flat plate, in the investigation presented here. The study mainly aims at comparing two different fringe orientations in the wedge fringe setting of Mach-Zehnder interferometer (MZI), used for the measurements. The interference fringes are set in horizontal and vertical orientations with respect to the heated surface, and two different fringe analysis methods, namely the stepping method and the method proposed by Naylor and Duarte, are used to obtain the heat transfer coefficients. The experimental system is benchmarked with theoretical results, thus validating its reliability in heat transfer measurements. The interference fringe patterns are analyzed digitally using MATLAB 7 and MOTIC Plus softwares, which ensure improved efficiency in fringe analysis, hence reducing the errors associated with conventional fringe tracing. The work also discuss the relative merits and limitations of the two methods used.
Abstract: This paper is concerned with the production of an Arabic word semantic similarity benchmark dataset. It is the first of its kind for Arabic which was particularly developed to assess the accuracy of word semantic similarity measurements. Semantic similarity is an essential component to numerous applications in fields such as natural language processing, artificial intelligence, linguistics, and psychology. Most of the reported work has been done for English. To the best of our knowledge, there is no word similarity measure developed specifically for Arabic. In this paper, an Arabic benchmark dataset of 70 word pairs is presented. New methods and best possible available techniques have been used in this study to produce the Arabic dataset. This includes selecting and creating materials, collecting human ratings from a representative sample of participants, and calculating the overall ratings. This dataset will make a substantial contribution to future work in the field of Arabic WSS and hopefully it will be considered as a reference basis from which to evaluate and compare different methodologies in the field.
Abstract: For evaluating the severity of Chronic Obstructive Pulmonary Disease (COPD), one is interested in inspecting the airway wall thickening due to inflammation. Although airway segmentations have being well developed to reconstruct in high order, airway wall segmentation remains a challenge task. While tackling such problem as a multi-surface segmentation, the interrelation within surfaces needs to be considered. We propose a new method for three-dimensional airway wall segmentation using spring structural active contour model. The method incorporates the gravitational field of the image and repelling force field of the inner lumen as the soft constraint and the geometric spring structure of active contour as the hard constraint to approximate a three-dimensional coupled surface readily for thickness measurements. The results show the preservation of topology constraints of coupled surfaces. In conclusion, our springy, soft-tissue-like structure ensures the globally optimal solution and waives the shortness following by the inevitable improper inner surface constraint.
Abstract: In this article, we propose a methodology for the
characterization of the suspended matter along Algiers-s bay. An
approach by multi layers perceptron (MLP) with training by back
propagation of the gradient optimized by the algorithm of Levenberg
Marquardt (LM) is used. The accent was put on the choice of the
components of the base of training where a comparative study made
for four methods: Random and three alternatives of classification by
K-Means. The samples are taken from suspended matter image,
obtained by analytical model based on polynomial regression by
taking account of in situ measurements. The mask which selects the
zone of interest (water in our case) was carried out by using a multi
spectral classification by ISODATA algorithm. To improve the
result of classification, a cleaning of this mask was carried out using
the tools of mathematical morphology. The results of this study
presented in the forms of curves, tables and of images show the
founded good of our methodology.
Abstract: After the terrorist attack on September 11, 2001 in
U.S., the container security issue got high attention, especially by U.S.
government, which deployed a lot of measures to promote or improve
security systems. U.S. government not only enhances its national
security system, but allies with other countries against the potential
terrorist attacks in the future. For example CSI (Container Security
Initiative), it encourages foreign ports outside U.S. to become CSI
ports as a part of U.S. anti-terrorism network. Although promotion of
the security could partly reach the goal of anti-terrorism, that will
influence the efficiency of container supply chain, which is the main
concern when implementing the inspection measurements. This paper
proposes a quick estimation methodology for an inspection service
rate by a berth allocation heuristic such that the inspection activities
will not affect the original container supply chain. Theoretical and
simulation results show this approach is effective.
Abstract: This paper presents the prediction of kidney
dysfunction using different neural network (NN) approaches. Self
organization Maps (SOM), Probabilistic Neural Network (PNN) and
Multi Layer Perceptron Neural Network (MLPNN) trained with Back
Propagation Algorithm (BPA) are used in this study. Six hundred and
sixty three sets of analytical laboratory tests have been collected from
one of the private clinical laboratories in Baghdad. For each subject,
Serum urea and Serum creatinin levels have been analyzed and tested
by using clinical laboratory measurements. The collected urea and
cretinine levels are then used as inputs to the three NN models in
which the training process is done by different neural approaches.
SOM which is a class of unsupervised network whereas PNN and
BPNN are considered as class of supervised networks. These
networks are used as a classifier to predict whether kidney is normal
or it will have a dysfunction. The accuracy of prediction, sensitivity
and specificity were found for each type of the proposed networks
.We conclude that PNN gives faster and more accurate prediction of
kidney dysfunction and it works as promising tool for predicting of
routine kidney dysfunction from the clinical laboratory data.
Abstract: In a competitive production environment, critical
decision making are based on data resulted by random sampling of
product units. Efficiency of these decisions depends on data quality
and also their reliability scale. This point leads to the necessity of a
reliable measurement system. Therefore, the conjecture process and
analysing the errors contributes to a measurement system known as
Measurement System Analysis (MSA). The aim of this research is on
determining the necessity and assurance of extensive development in
analysing measurement systems, particularly with the use of
Repeatability and Reproducibility Gages (GR&R) to improve
physical measurements. Nowadays in productive industries,
repeatability and reproducibility gages released so well but they are
not applicable as well as other measurement system analysis
methods. To get familiar with this method and gain a feedback in
improving measurement systems, this survey would be on
“ANOVA" method as the most widespread way of calculating
Repeatability and Reproducibility (R&R).
Abstract: The acidity of different raw Jordanian clays
containing zeolite, bentonite, red and white kaolinite and diatomite
was characterized by means of temperature programmed desorption
(TPD) of ammonia, conversion of 2-methyl-3-butyn-2-ol (MBOH),
FTIR and BET-measurements. FTIR spectra proved presence of
silanol and bridged hydroxyls on the clay surface. The number of
acidic sites was calculated from experimental TPD-profiles. We
observed the decrease of surface acidity correlates with the decrease
of Si/Al ratio except for diatomite. On the TPD-plot for zeolite two
maxima were registered due to different strength of surface acidic
sites. Values of MBOH conversion, product yields and selectivity
were calculated for the catalysis on Jordanian clays. We obtained that
all clay samples are able to convert MBOH into a major product
which is 3-methyl-3-buten-1-yne (MBYNE) catalyzed by acid
surface sites with the selectivity close to 70%. There was found a
correlation between MBOH conversion and acidity of clays
determined by TPD-NH3, i.e. the higher the acidity the higher the
conversion of MBOH. However, diatomite provided the lowest
conversion of MBOH as result of poor polarization of silanol groups.
Comparison of surface areas and conversions revealed the highest
density of active sites for red kaolinite and the lowest for zeolite and
diatomite.
Abstract: The common practice of operating S-rotor is in an
open environment; however there are times when the rotor is
installed in a bounded environment and there might be changes in the
performance of the rotor. This paper presents the changes in the
performance of S-rotor when operated in bounded flows. The
investigation was conducted experimentally to compare the
performance of the rotors in bounded environment against open
environment. Three different rotors models were designed, fabricated
and subjected to experimental measurements. All of the three models
were having 600 mm height and 300 mm Diameter. They were tested
in three different flow environments; namely: partially bounded
environment, fully bounded environment and open environment.
Rotors were found to have better starting up capabilities when
operated in bounded environment. Apart from that, all rotors manage
to achieve higher Power and Torque Coefficients at a higher Tip
Speed Ratio as compared to the open environment.
Abstract: In order to provide accurate heart rate variability
indices of sympathetic and parasympathetic activity, the low
frequency and high frequency components of an RR heart rate signal
must be adequately separated. This is not always possible by just
applying spectral analysis, as power from the high and low frequency
components often leak into their adjacent bands. Furthermore,
without the respiratory spectra it is not obvious that the low
frequency component is not another respiratory component, which
can appear in the lower band. This paper describes an adaptive filter,
which aids the separation of the low frequency sympathetic and high
frequency parasympathetic components from an ECG R-R interval
signal, enabling the attainment of more accurate heart rate variability
measures. The algorithm is applied to simulated signals and heart rate
and respiratory signals acquired from an ambulatory monitor
incorporating single lead ECG and inductive plethysmography
sensors embedded in a garment. The results show an improvement
over standard heart rate variability spectral measurements.
Abstract: The aim of this study was to develop a dynamic cardiac phantom for quality control in myocardial scintigraphy. The dynamic heart phantom constructed only contained the left ventricle, made of elastic material (latex), comprising two cavities: one internal and one external. The data showed a non-significant variation in the values of left ventricular ejection fraction (LVEF) obtained by varying the heart rate. It was also possible to evaluate the ejection fraction (LVEF) through different arrays of image acquisition and to perform an intercomparison of LVEF by two different scintillation cameras. The results of the quality control tests were satisfactory, showing that they can be used as parameters in future assessments. The new dynamic heart phantom was demonstrated to be effective for use in LVEF measurements. Therefore, the new heart simulator is useful for the quality control of scintigraphic cameras.
Abstract: This paper presents an approach for the determination of the optimal cutting parameters (spindle speed, feed rate, depth of cut and engagement) leading to minimum surface roughness in face milling of high silicon stainless steel by coupling neural network (NN) and Electromagnetism-like Algorithm (EM). In this regard, the advantages of statistical experimental design technique, experimental measurements, artificial neural network, and Electromagnetism-like optimization method are exploited in an integrated manner. To this end, numerous experiments on this stainless steel were conducted to obtain surface roughness values. A predictive model for surface roughness is created by using a back propogation neural network, then the optimization problem was solved by using EM optimization. Additional experiments were performed to validate optimum surface roughness value predicted by EM algorithm. It is clearly seen that a good agreement is observed between the predicted values by EM coupled with feed forward neural network and experimental measurements. The obtained results show that the EM algorithm coupled with back propogation neural network is an efficient and accurate method in approaching the global minimum of surface roughness in face milling.
Abstract: Electromagnetic flowmeters with DC excitation are used for a wide range of fluid measurement tasks, but are rarely found in dosing applications with short measurement cycles due to the achievable accuracy. This paper will identify a number of factors that influence the accuracy of this sensor type when used for short-term measurements. Based on these results a new signal-processing algorithm will be described that overcomes the identified problems to some extend. This new method allows principally a higher accuracy of electromagnetic flowmeters with DC excitation than traditional methods.
Abstract: In automotive systems almost all steps concerning the
calibration of several control systems, e.g., low idle governor or
boost pressure governor, are made with the vehicle because the timeto-
production and cost requirements on the projects do not allow for
the vehicle analysis necessary to build reliable models. Here is
presented a procedure using parametric and NN (neural network)
models that enables the generation of vehicle system models based
on normal ECU engine control unit) vehicle measurements. These
models are locally valid and permit pre and follow-up calibrations so
that, only the final calibrations have to be done with the vehicle.