Abstract: In the modern construction practices, industrial wastes
or by-products are largely used as raw materials in cement and
concrete. These impart many benefits to the environment and bringabout
an economic impact because the cost of waste disposal is
constantly increasing due to strict environmental regulations. It was
reported in literature that the leakage of oil onto concrete element in
older cement grinding unit resulted in concrete with greater resistance
to freezing and thawing. This effect was thought to be similar to
adding an air-entraining chemical admixture to concrete. This paper
presents an investigation on the load deflection behaviour and crack
patterns of reinforced concrete (RC) beams subjected to four point
loading. Ten 120x260x1900 mm beams were cast with 100%
ordinary Portland cement (OPC) concrete, 20% fly ash (FA) and 20%
rice husk ash (RHA) blended cement concrete. 0.15% dosage of
admixtures (used engine oil, new engine oil, and superplasticizer)
was used throughout the experiment. Results show that OPC and
OPC/RHA RC beams containing used engine oil and superplasticizer
exhibit higher capacity, 18-26% than their corresponding control
mix.
Abstract: The contact width is important design parameter for
optimizing the design of new metal gasket for asbestos substitution
gasket. The contact width is found have relationship with the helium
leak quantity. In the increasing of axial load value, the helium leak
quantity is decreasing and the contact width is increasing. This study
provides validity method using simulation analysis and the result is
compared to experimental using pressure sensitive paper. The results
denote similar trend data between simulation and experimental result.
Final evaluation is determined by helium leak quantity to check
leakage performance of gasket design. Considering the phenomena of
position change on the convex contact, it can be developed the
optimization of gasket design by increasing contact width.
Abstract: Skip cycle is a working strategy for spark ignition
engines, which allows changing the effective stroke of an engine
through skipping some of the four stroke cycles. This study proposes
a new mechanism to achieve the desired skip-cycle strategy for
internal combustion engines. The air and fuel leakage, which occurs
through the gas exchange, negatively affects the efficiency of the
engine at high speeds and loads. An absolute sealing is assured by
direct use of poppet valves, which are kept in fully closed position
during the skipped mode. All the components of the mechanism were
designed according to the real dimensions of the Anadolu Motor's
gasoline engine and modeled in 3D by means of CAD software. As
the mechanism operates in two modes, two dynamically equivalent
models are established to obtain the force and strength analysis for
critical components.
Abstract: This paper presents the simulation the results of
electric field and potential distributions along surface of silicone
rubber polymer insulators. Near the same leakage distance subjected
to 15 kV in 50 cycle salt fog ageing test, alternate sheds silicone
rubber polymer insulator showed better contamination performance
than straight sheds silicone rubber polymer insulator. Severe surface
ageing was observed on the straight sheds insulator. The objective of
this work is to elucidate that electric field distribution along straight
sheds insulator higher than alternate shed insulator in salt fog ageing
test. Finite element method (FEM) is adopted for this work. The
simulation results confirmed the experimental data, as well.
Abstract: Management is required to understand all information security risks within an organization, and to make decisions on which information security risks should be treated in what level by allocating how much amount of cost. However, such decision-making is not usually easy, because various measures for risk treatment must be selected with the suitable application levels. In addition, some measures may have objectives conflicting with each other. It also makes the selection difficult. Therefore, this paper provides a model which supports the selection of measures by applying multi-objective analysis to find an optimal solution. Additionally, a list of measures is also provided to make the selection easier and more effective without any leakage of measures.
Abstract: Two-interconnected fluidized bed systems are widely used in various processes such as Fisher-Tropsch, hot gas desulfurization, CO2 capture-regeneration with dry sorbent, chemical-looping combustion, sorption enhanced steam methane reforming, chemical-looping hydrogen generation system, and so on. However, most of two-interconnected fluidized beds systems require riser and/or pneumatic transport line for solid conveying and loopseals or seal-pots for gas sealing, recirculation of solids to the riser, and maintaining of pressure balance. The riser (transport bed) is operated at the high velocity fluidization condition and residence times of gas and solid in the riser are very short. If the reaction rate of catalyst or sorbent is slow, the riser can not ensure sufficient contact time between gas and solid and we have to use two bubbling beds for each reaction to ensure sufficient contact time. In this case, additional riser must be installed for solid circulation. Consequently, conventional two-interconnected fluidized bed systems are very complex, large, and difficult to operate. To solve these problems, a novel two-interconnected fluidized bed system has been developed. This system has two bubbling beds, solid injection nozzles, solid conveying lines, and downcomers. In this study, effects of operating variables on solid circulation rate, gas leakage between two beds have been investigated in a cold mode two-interconnected fluidized bed system. Moreover, long-term operation of continuous solid circulation up to 60 hours has been performed to check feasibility of stable operation.
Abstract: The clinical usefulness of heart rate variability is
limited to the range of Holter monitoring software available. These
software algorithms require a normal sinus rhythm to accurately
acquire heart rate variability (HRV) measures in the frequency
domain. Premature ventricular contractions (PVC) or more
commonly referred to as ectopic beats, frequent in heart failure,
hinder this analysis and introduce ambiguity. This investigation
demonstrates an algorithm to automatically detect ectopic beats by
analyzing discrete wavelet transform coefficients. Two techniques
for filtering and replacing the ectopic beats from the RR signal are
compared. One technique applies wavelet hard thresholding
techniques and another applies linear interpolation to replace ectopic
cycles. The results demonstrate through simulation, and signals
acquired from a 24hr ambulatory recorder, that these techniques can
accurately detect PVC-s and remove the noise and leakage effects
produced by ectopic cycles retaining smooth spectra with the
minimum of error.
Abstract: Bond graph models of an electrical transformer
including the nonlinear saturation are presented. These models
determine the relation between self and mutual inductances, and
the leakage and magnetizing inductances of power transformers
with two and three windings using the properties of a bond
graph. The modelling and analysis using this methodology to
three phase power transformers or transformers with internal
incipient faults can be extended.
Abstract: This paper propose a new circuit design which
monitor total leakage current during standby mode and generates the
optimal reverse body bias voltage, by using the adaptive body bias
(ABB) technique to compensate die-to-die parameter variations.
Design details of power monitor are examined using simulation
framework in 65nm and 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 10 μW for 32nm technology and
about 12 μW for 65nm technology at the same power supply voltage
as the core power supply. Moreover the results show that our
proposed circuit design is not far sensitive to the temperature
variations and also process variations. Besides, uses the simple
blocks which offer good sensitivity, high speed, the continuously
feedback loop.
Abstract: At the previous study of new metal gasket, contact
width and contact stress were important design parameter for
optimizing metal gasket performance. However, the range of contact
stress had not been investigated thoroughly. In this study, we
conducted a gasket design optimization based on an elastic and plastic
contact stress analysis considering forming effect using FEM. The
gasket model was simulated by using two simulation stages which is
forming and tightening simulation. The optimum design based on an
elastic and plastic contact stress was founded. Final evaluation was
determined by helium leak quantity to check leakage performance of
both type of gaskets. The helium leak test shows that a gasket based
on the plastic contact stress design better than based on elastic stress
design.
Abstract: The effect of the blade tip geometry of a high pressure
gas turbine is studied experimentally and computationally for high
speed leakage flows. For this purpose two simplified models are
constructed, one models a flat tip of the blade and the second models
a cavity tip of the blade. Experimental results are obtained from a
transonic wind tunnel to show the static pressure distribution along
the tip wall and provide flow visualization. RANS computations
were carried to provide further insight into the mean flow behavior
and to calculate the discharge coefficient which is a measure of the
flow leaking over the tip. It is shown that in both geometries of tip
the flow separates over the tip to form a separation bubble. The
bubble is higher for the cavity tip while a complete shock wave
system of oblique waves ending with a normal wave can be seen for
the flat tip. The discharge coefficient for the flat tip shows less
dependence on the pressure ratio over the blade tip than the cavity
tip. However, the discharge coefficient for the cavity tip is lower than
that of the flat tip, showing a better ability to reduce the leakage flow
and thus increase the turbine efficiency.
Abstract: This paper analyzes different techniques of the fine grained security of relational databases for the two variables-data accessibility and inference. Data accessibility measures the amount of data available to the users after applying a security technique on a table. Inference is the proportion of information leakage after suppressing a cell containing secret data. A row containing a secret cell which is suppressed can become a security threat if an intruder generates useful information from the related visible information of the same row. This paper measures data accessibility and inference associated with row, cell, and column level security techniques. Cell level security offers greatest data accessibility as it suppresses secret data only. But on the other hand, there is a high probability of inference in cell level security. Row and column level security techniques have least data accessibility and inference. This paper introduces cell plus innocent security technique that utilizes the cell level security method but suppresses some innocent data to dodge an intruder that a suppressed cell may not necessarily contain secret data. Four variations of the technique namely cell plus innocent 1/4, cell plus innocent 2/4, cell plus innocent 3/4, and cell plus innocent 4/4 respectively have been introduced to suppress innocent data equal to 1/4, 2/4, 3/4, and 4/4 percent of the true secret data inside the database. Results show that the new technique offers better control over data accessibility and inference as compared to the state-of-theart security techniques. This paper further discusses the combination of techniques together to be used. The paper shows that cell plus innocent 1/4, 2/4, and 3/4 techniques can be used as a replacement for the cell level security.
Abstract: Factoring Boolean functions is one of the basic operations in algorithmic logic synthesis. A novel algebraic factorization heuristic for single-output combinatorial logic functions is presented in this paper and is developed based on the set theory paradigm. The impact of factoring is analyzed mainly from a low power design perspective for standard cell based digital designs in this paper. The physical implementation of a number of MCNC/IWLS combinational benchmark functions and sub-functions are compared before and after factoring, based on a simple technology mapping procedure utilizing only standard gate primitives (readily available as standard cells in a technology library) and not cells corresponding to optimized complex logic. The power results were obtained at the gate-level by means of an industry-standard power analysis tool from Synopsys, targeting a 130nm (0.13μm) UMC CMOS library, for the typical case. The wire-loads were inserted automatically and the simulations were performed with maximum input activity. The gate-level simulations demonstrate the advantage of the proposed factoring technique in comparison with other existing methods from a low power perspective, for arbitrary examples. Though the benchmarks experimentation reports mixed results, the mean savings in total power and dynamic power for the factored solution over a non-factored solution were 6.11% and 5.85% respectively. In terms of leakage power, the average savings for the factored forms was significant to the tune of 23.48%. The factored solution is expected to better its non-factored counterpart in terms of the power-delay product as it is well-known that factoring, in general, yields a delay-efficient multi-level solution.
Abstract: Water leakage is a serious problem in the maintenance of a waterworks facility. Monitoring the water flow rate is one way to locate leakage. However, conventional flowmeters such as the wet-type flowmeter and the clamp-on type ultrasonic flowmeter require additional construction for their installation and are therefore quite expensive. This paper proposes a novel estimation system for the flow rate in a water pipeline, which employs a vibration sensor. This assembly can be attached to any water pipeline without the need for additional high-cost construction. The vibration sensor is designed based on a condenser microphone. This sensor detects vibration caused by water flowing through a pipeline. It is possible to estimate the water flow rate by measuring the amplitude of the output signal from the vibration sensor. We confirmed the validity of the proposed sensing system experimentally.
Abstract: Recently, as the scale of construction projects has
increases, more ground excavation for foundations is carried out than ever before. Consequently, damage to underground ducts (gas, water/sewage or oil pipelines, communication cables or power cable ducts) or superannuated pipelines frequently cause serious accidents
resulting in damage to life and property. (In Korea, the total length of city water pipelines was approximately 2,000 km as of the end of 2009.) In addition, large amounts of damage caused by fractures, water
and gas leakage caused by superannuation or damage to underground
ducts in construction has been reported. Therefore, a system is required to precisely detect defects and deterioration in underground
pipelines and the locations of such defects, for timely and accurate
maintenance or replacement of the ducts. In this study, a system was
developed which can locate underground structures (gas and water
pipelines, power cable ducts, etc.) in 3D-coordinates and monitor the
degree and position of defects using an Inertial Measurement Unit
(IMU) sensing technique. The system can prevent damage to underground ducts and superannuated pipelines during construction,
and provide reliable data for maintenance. The utility of the IMU sensing technique used in aircraft and ships in civil applications was
verified.
Abstract: This paper presents a novel CMOS four-transistor
SRAM cell for very high density and low power embedded SRAM
applications as well as for stand-alone SRAM applications. This cell
retains its data with leakage current and positive feedback without
refresh cycle. The new cell size is 20% smaller than a conventional
six-transistor cell using same design rules. Also proposed cell uses
two word-lines and one pair bit-line. Read operation perform from
one side of cell, and write operation perform from another side of
cell, and swing voltage reduced on word-lines thus dynamic power
during read/write operation reduced. The fabrication process is fully
compatible with high-performance CMOS logic technologies,
because there is no need to integrate a poly-Si resistor or a TFT load.
HSPICE simulation in standard 0.25μm CMOS technology confirms
all results obtained from this paper.
Abstract: A person-to-person information sharing is easily realized
by P2P networks in which servers are not essential. Leakage
of information, which are caused by malicious accesses for P2P
networks, has become a new social issues. To prevent information
leakage, it is necessary to detect and block traffics of P2P software.
Since some P2P softwares can spoof port numbers, it is difficult to
detect the traffics sent from P2P softwares by using port numbers.
It is more difficult to devise effective countermeasures for detecting
the software because their protocol are not public.
In this paper, a discriminating method of network applications
based on communication characteristics of application messages
without port numbers is proposed. The proposed method is based
on an assumption that there can be some rules about time intervals
to transmit messages in application layer and the number of necessary
packets to send one message. By extracting the rule from network
traffic, the proposed method can discriminate applications without
port numbers.
Abstract: With rapid technology scaling, the proportion of the
static power consumption catches up with dynamic power
consumption gradually. To decrease leakage consumption is
becoming more and more important in low-power design. This paper
presents a power-gating scheme for P-DTGAL (p-type dual
transmission gate adiabatic logic) circuits to reduce leakage power
dissipations under deep submicron process. The energy dissipations of
P-DTGAL circuits with power-gating scheme are investigated in
different processes, frequencies and active ratios. BSIM4 model is
adopted to reflect the characteristics of the leakage currents. HSPICE
simulations show that the leakage loss is greatly reduced by using the
P-DTGAL with power-gating techniques.
Abstract: In this study, the Taguchi method was used to optimize the effect of HALO structure or halo implant variations on threshold voltage (VTH) and leakage current (ILeak) in 45nm p-type Metal Oxide Semiconductor Field Effect Transistors (MOSFETs) device. Besides halo implant dose, the other process parameters which used were Source/Drain (S/D) implant dose, oxide growth temperature and silicide anneal temperature. This work was done using TCAD simulator, consisting of a process simulator, ATHENA and device simulator, ATLAS. These two simulators were combined with Taguchi method to aid in design and optimize the process parameters. In this research, the most effective process parameters with respect to VTH and ILeak are halo implant dose (40%) and S/D implant dose (52%) respectively. Whereas the second ranking factor affecting VTH and ILeak are oxide growth temperature (32%) and halo implant dose (34%) respectively. The results show that after optimizations approaches is -0.157V at ILeak=0.195mA/μm.
Abstract: The previous study of new metal gasket that contact
width and contact stress an important design parameter for optimizing
metal gasket performance. The optimum design based on an elastic
and plastic contact stress was founded. However, the influence of
flange surface roughness had not been investigated thoroughly. The
flange has many kinds of surface roughness. In this study, we
conducted a gasket model include a flange surface roughness effect. A
finite element method was employed to develop simulation solution. A
uniform quadratic mesh used for meshing the gasket material and a
gradually quadrilateral mesh used for meshing the flange. The gasket
model was simulated by using two simulation stages which is forming
and tightening simulation. A simulation result shows that a smoother
of surface roughness has higher slope for force per unit length. This
mean a squeezed against between flange and gasket will be strong. The
slope of force per unit length for gasket 400-MPa mode was higher
than the gasket 0-MPa mode.