Abstract: This paper presents the experimental results of
discharge current phenomena on various humidity, temperature,
pressure and pollutant conditions of epoxy resin specimen. The
leakage distance of specimen was 3 cm, that it was supplied by high
voltage. The polluted condition was given with NaCl artificial
pollutant. The conducted measurements were discharge current and
applied voltage. The specimen was put in a hermetically sealed
chamber, and the current waveforms were analyzed with FFT.
The result indicated that on discharge condition, the fifth
harmonics still had dominant, rather than third one. The third
harmonics tent to be appeared on low pressure heavily polluted
condition, and followed by high humidity heavily polluted condition.
On the heavily polluted specimen, the peaks discharge current points
would be high and more frequent. Nevertheless, the specimen still
had capacitive property. Besides that, usually discharge current
points were more frequent. The influence of low pressure was still
dominant to be easier to discharge. The non-linear property would be
appear explicitly on low pressure and heavily polluted condition.
Abstract: The major part of light weight timber constructions
consists of insulation. Mineral wool is the most commonly used
insulation due to its cost efficiency and easy handling. The fiber
orientation and porosity of this insulation material enables flowthrough.
The air flow resistance is low. If leakage occurs in the
insulated bay section, the convective flow may cause energy losses
and infiltration of the exterior wall with moisture and particles. In
particular the infiltrated moisture may lead to thermal bridges and
growth of health endangering mould and mildew. In order to prevent
this problem, different numerical calculation models have been
developed. All models developed so far have a potential for
completion. The implementation of the flow-through properties of
mineral wool insulation may help to improve the existing models.
Assuming that the real pressure difference between interior and
exterior surface is larger than the prescribed pressure difference in the
standard test procedure for mineral wool ISO 9053 / EN 29053,
measurements were performed using the measurement setup for
research on convective moisture transfer “MSRCMT".
These measurements show, that structural inhomogeneities of
mineral wool effect the permeability only at higher pressure
differences, as applied in MSRCMT. Additional microscopic
investigations show, that the location of a leak within the
construction has a crucial influence on the air flow-through and the
infiltration rate. The results clearly indicate that the empirical values
for the acoustic resistance of mineral wool should not be used for the
calculation of convective transfer mechanisms.
Abstract: Reducing the risk of information leaks is one of
the most important functions of identity management systems. To
achieve this purpose, Dey et al. have already proposed an account
management method for a federated login system using a blind
signature scheme. In order to ensure account anonymity for the
authentication provider, referred to as an IDP (identity provider),
a blind signature scheme is utilized to generate an authentication
token on an authentication service and the token is sent to an IDP.
However, there is a problem with the proposed system. Malicious
users can establish multiple accounts on an IDP by requesting such
accounts. As a measure to solve this problem, in this paper, the
authors propose an account checking method that is performed before
account generation.
Abstract: In this work, the physical based device model of
AlGaN/GaN high electron mobility transistors (HEMTs) has been
established and the corresponding device operation behavior has
been investigated also by using Sentaurus TCAD from Synopsys.
Advanced AlGaN/GaN hetero-structures with GaN cap layer and AlN
spacer have been considered and the GaN cap layer and AlN spacer
are found taking important roles on the gate leakage blocking and
off-state breakdown voltage enhancement.
Abstract: A Comparison and evaluation of the different
condition monitoring (CM) techniques was applied experimentally
on RC e.g. Dynamic cylinder pressure and crankshaft Instantaneous
Angular Speed (IAS), for the detection and diagnosis of valve faults
in a two - stage reciprocating compressor for a programme of
condition monitoring which can successfully detect and diagnose a
fault in machine. Leakage in the valve plate was introduced
experimentally into a two-stage reciprocating compressor. The effect
of the faults on compressor performance was monitored and the
differences with the normal, healthy performance noted as a fault
signature been used for the detection and diagnosis of faults.
The paper concludes with what is considered to be a unique
approach to condition monitoring. First, each of the two most useful
techniques is used to produce a Truth Table which details the
circumstances in which each method can be used to detect and
diagnose a fault. The two Truth Tables are then combined into a
single Decision Table to provide a unique and reliable method of
detection and diagnosis of each of the individual faults introduced
into the compressor. This gives accurate diagnosis of compressor
faults.
Abstract: The hydraulic actuated excavator, being a non-linear
mobile machine, encounters many uncertainties. There are
uncertainties in the hydraulic system in addition to the uncertain
nature of the load. The simulation results obtained in this study show
that there is a need for intelligent control of such machines and in
particular interval type-2 fuzzy controller is most suitable for
minimizing the position error of a typical excavator-s bucket under
load variations. We consider the model parameter uncertainties such
as hydraulic fluid leakage and friction. These are uncertainties which
also depend up on the temperature and alter bulk modulus and
viscosity of the hydraulic fluid. Such uncertainties together with the
load variations cause chattering of the bucket position. The interval
type-2 fuzzy controller effectively eliminates the chattering and
manages to control the end-effecter (bucket) position with positional
error in the order of few millimeters.
Abstract: Modern applications realized onto FPGAs exhibit high connectivity demands. Throughout this paper we study the routing constraints of Virtex devices and we propose a systematic methodology for designing a novel general-purpose interconnection network targeting to reconfigurable architectures. This network consists of multiple segment wires and SB patterns, appropriately selected and assigned across the device. The goal of our proposed methodology is to maximize the hardware utilization of fabricated routing resources. The derived interconnection scheme is integrated on a Virtex style FPGA. This device is characterized both for its high-performance, as well as for its low-energy requirements. Due to this, the design criterion that guides our architecture selections was the minimal Energy×Delay Product (EDP). The methodology is fully-supported by three new software tools, which belong to MEANDER Design Framework. Using a typical set of MCNC benchmarks, extensive comparison study in terms of several critical parameters proves the effectiveness of the derived interconnection network. More specifically, we achieve average Energy×Delay Product reduction by 63%, performance increase by 26%, reduction in leakage power by 21%, reduction in total energy consumption by 11%, at the expense of increase of channel width by 20%.
Abstract: The development of shape and size of a crack in a
pressure vessel under uniaxial and biaxial loadings is important in
fitness-for-service evaluations such as leak-before-break. In this
work finite element modelling was used to evaluate the mean stress
and the J-integral around a front of a surface-breaking crack. A
procedure on the basis of ductile tearing resistance curves of high and
low constrained fracture mechanics geometries was developed to
estimate the amount of ductile crack extension for surface-breaking
cracks and to show the evolution of the initial crack shape. The
results showed non-uniform constraint levels and crack driving forces
around the crack front at large deformation levels. It was also shown
that initially semi-elliptical surface cracks under biaxial load
developed higher constraint levels around the crack front than in
uniaxial tension. However similar crack shapes were observed with
more extensions associated with cracks under biaxial loading.
Abstract: This paper describes an automated event detection and location system for water distribution pipelines which is based upon low-cost sensor technology and signature analysis by an Artificial
Neural Network (ANN). The development of a low cost failure sensor which measures the opacity or cloudiness of the local water
flow has been designed, developed and validated, and an ANN based system is then described which uses time series data produced by
sensors to construct an empirical model for time series prediction and
classification of events. These two components have been installed,
tested and verified in an experimental site in a UK water distribution
system. Verification of the system has been achieved from a series of
simulated burst trials which have provided real data sets. It is concluded that the system has potential in water distribution network
management.
Abstract: In this paper, a multi-agent robot system is presented. The system consists of four robots. The developed robots are able to automatically enter and patrol a harmful environment, such as the building infected with virus or the factory with leaking hazardous gas. Further, every robot is able to perform obstacle avoidance and search for the victims. Several operation modes are designed: remote control, obstacle avoidance, automatic searching, and so on.
Abstract: High performance Resistive Random Access Memory
(RRAM) based on HfOx has been prepared and its temperature
instability has been investigated in this work. With increasing
temperature, it is found that: leakage current at high resistance state
increases, which can be explained by the higher density of traps
inside dielectrics (related to trap-assistant tunneling), leading to a
smaller On/Off ratio; set and reset voltages decrease, which may be
attributed to the higher oxygen ion mobility, in addition to the
reduced potential barrier to create / recover oxygen ions (or oxygen
vacancies); temperature impact on the RRAM retention degradation
is more serious than electrical bias.
Abstract: The blood ducts must be occluded to avoid loss of
blood from vessels in laparoscopic surgeries. This paper presents a
locking mechanism to be used in a ligation laparoscopic procedure
(LigLAP I), as an alternative solution for a stapling procedure.
Currently, stapling devices are being used to occlude vessels. Using
these devices may result in some problems, including injury of bile
duct, taking up a great deal of space behind the vessel, and bile leak.
In this new procedure, a two-layer suture occludes a vessel. A
locking mechanism is also required to hold the suture. Since there is
a limited space at the device tip, a Shape Memory Alloy (SMA)
actuator is used in this mechanism. Suitability for cleanroom
applications, small size, and silent performance are among the
advantages of SMA actuators in biomedical applications. An
experimental study is conducted to examine the function of the
locking mechanism. To set up the experiment, a prototype of a
locking mechanism is built using nitinol, which is a nickel-titanium
shape memory alloy. The locking mechanism successfully locks a
polymer suture for all runs of the experiment. In addition, the effects
of various surface materials on the applied pulling forces are studied.
Various materials are mounted at the mechanism tip to compare the
maximum pulling forces applied to the suture for each material. The
results show that the various surface materials on the device tip
provide large differences in the applied pulling forces.
Abstract: This paper proposes a low power SRAM based on
five transistor SRAM cell. Proposed SRAM uses novel word-line
decoding such that, during read/write operation, only selected cell
connected to bit-line whereas, in conventional SRAM (CV-SRAM),
all cells in selected row connected to their bit-lines, which in turn
develops differential voltages across all bit-lines, and this makes
energy consumption on unselected bit-lines. In proposed SRAM
memory array divided into two halves and this causes data-line
capacitance to reduce. Also proposed SRAM uses one bit-line and
thus has lower bit-line leakage compared to CV-SRAM.
Furthermore, the proposed SRAM incurs no area overhead, and has
comparable read/write performance versus the CV-SRAM.
Simulation results in standard 0.25μm CMOS technology shows in
worst case proposed SRAM has 80% smaller dynamic energy
consumption in each cycle compared to CV-SRAM. Besides, energy
consumption in each cycle of proposed SRAM and CV-SRAM
investigated analytically, the results of which are in good agreement
with the simulation results.
Abstract: The interaction of the blade tip with the casing
boundary layer and the leakage flow may lead to a kind of cavitation
namely tip vortex cavitation. In this study, the onset of tip vortex
cavitation was experimentally investigated in an axial flow pump.
For a constant speed and a fixed angle of attack and by changing the
flow rate, the pump head, input power, output power and efficiency
were calculated and the pump characteristic curves were obtained.
The cavitation phenomenon was observed with a camera and a
stroboscope. Finally, the critical flow region, which tip vortex
cavitation might have occurred, was identified. The results show that
just by adjusting the flow rate, out of the specified region, the
possibility of occurring tip vortex cavitation, decreases to a great
extent.
Abstract: The resident registration number was adopted for the purposes of enhanced services for resident convenience and effective performance of governmental administrative affairs. However, it has been used for identification purposes customarily and irrationally in line with the development and spread of the Internet. In response to the growing concern about the leakage of collected RRNs and possible abuses of stolen RRNs, e.g. identity theft, for crimes, the Korean Communications Commission began to take legal/regulatory actions in 2011 to minimize the online collection and use of resident registration numbers. As the use of the RRN was limited after the revision of the Act on Promotion of Information and Communications Network Utilization and Information Protection, etc., online business providers were required to have alternatives to the RRN for the purpose of identifying the user's identity and age, in compliance with the law, and settling disputes with customers. This paper presents means of verifying the personal identity by taking advantage of the commonly used infrastructure and simply replacing personal information entered and stored, without requiring users to enter their RRNs.