Abstract: The present paper examines the impact noise
transmission through some floor building assemblies. The Acoubat
software numerical simulation has been used to simulate the impact
noise transmission through different floor configurations used in
Algerian construction mode. The results are compared with the
available measurements. We have developed two experimental
methods, i) field method, and ii) laboratory method using Brüel and
Kjær equipments. The results show that the different cases of floor
configurations need some improvement to ensure the acoustic
comfort in the receiving apartment. The recommended value of the
impact sound level in the receiving room should not exceed 58 dB.
The important results obtained in this paper can be used as platform
to improve the Algerian building acoustic regulation aimed at the
construction of the multi-storey residential building.
Abstract: Mineral oil is commonly used for high voltage
transformer insulation. The insulation quality of mineral oil is
affecting the operation process of high voltage transformer. There are
many contaminations which could decrease the insulation quality of
mineral oil. One of them is water. This research talks about the effect
of water content on dielectric properties, physic properties, and
partial discharge pattern on mineral oil. Samples were varied with 10
varieties of water content value. And then all samples would be tested
to measure the dielectric properties, physic properties, and partial
discharge pattern. The result of this research showed that an
increment of water content value would decrease the insulation
quality of mineral oil.
Abstract: High frequency automotive interior noise above 500
Hz considerably affects automotive passenger comfort. To reduce this
noise, sound insulation material is often laminated on body panels or
interior trim panels. For a more effective noise reduction, the sound
reduction properties of this laminated structure need to be estimated.
We have developed a new calculate tool that can roughly calculate the
sound absorption and insulation properties of laminate structure and
handy for designers. In this report, the outline of this tool and an
analysis example applied to floor mat are introduced.
Abstract: In insulation and cooling of power transformers
various liquids are used. Mineral oils have wide availability and low
cost. However, they have a poor biodegradability potential and lower
fire point in comparison with other insulating liquids. Use of a liquid
having high biodegradability is important due to environmental
consideration. This paper investigates edible corn oil as an alternative
to mineral oil. Various properties of mineral and corn oil like
breakdown voltage, dissipation factor, relative dielectric constant,
power loss and resistivity were measured according to different
standards.
Abstract: This paper proposes a linear model for optimizing
domestic energy consumption in Romania. The particularity of the
model is that it is putting in competition both tangible technologies
and thermal insulation projects with different financing modes.
The model is optimizing the energy system by minimizing the
global discounted cost in household sector, by integrating residential
lighting, space heating, hot water, combined space heating – hot
water, as well as space cooling, in a monolithic model. Another
demand sector included is the passenger transport.
This paper focuses on space heating part, analyzing technical and
economic issues related to investment decisions to envelope and
insulate buildings, in order to minimize energy consumption.
Abstract: Potassium borates, which are widely used in welding
and metal refining industry, as a lubricating oil additive, cement
additive, fiberglass additive and insulation compound, are one of the
important groups of borate minerals. In this study the production of a
potassium borate mineral via hydrothermal method is aimed. The
potassium source of potassium nitrate (KNO3) was used along with a
sodium source of sodium hydroxide (NaOH) and boron source of
boric acid (H3BO3). The constant parameters of reaction temperature
and reaction time were determined as 80°C and 1 h, respectively. The
molar ratios of 1:1:3 (as KNO3:NaOH:H3BO3), 1:1:4, 1:1:5, 1:1:6
and 1:1:7 were used. Following the synthesis the identifications of
the produced products were conducted by X-Ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FT-IR) and Raman
Spectroscopy. The results of the experiments and analysis showed in
the ratio of 1:1:6, the Santite mineral with powder diffraction file
number (pdf no.) of 01-072-1688, which is known as potassium
pentaborate (KB5O8·4H2O) was synthesized as best.
Abstract: The performance of box-type solar cookers has been
reported by several researchers but little attention was paid to the
effect of the type of insulation material on the energy and exergy
efficiency of these cookers. This research aimed at evaluating the
energy and exergy efficiencies of the box-type cookers containing
different insulation materials. Energy and exergy efficiencies of five
box-type solar cookers insulated with maize cob, air (control), maize
husk, coconut coir and polyurethane foam respectively were obtained
over a period of three years. The cookers were evaluated using water
heating test procedures in determining the energy and exergy
analysis. The results were subjected to statistical analysis using
ANOVA. The result shows that the average energy input for the five
solar cookers were: 245.5, 252.2, 248.7, 241.5 and 245.5J
respectively while their respective average energy losses were: 201.2,
212.7, 208.4, 189.1 and 199.8J. The average exergy input for five
cookers were: 228.2, 234.4, 231.1, 224.4 and 228.2J respectively
while their respective average exergy losses were: 223.4, 230.6,
226.9, 218.9 and 223.0J. The energy and exergy efficiency was
highest in the cooker with coconut coir (37.35 and 3.90%
respectively) in the first year but was lowest for air (11 and 1.07%
respectively) in the third year. Statistical analysis showed significant
difference between the energy and exergy efficiencies over the years.
These results reiterate the importance of a good insulating material
for a box-type solar cooker.
Abstract: Problems insulation of building structures is often
closely connected with the problem of moisture remediation. In the
case of historic buildings or if only part of the redevelopment of
envelope of structures, it is not possible to apply the classical external
thermal insulation composite systems. This application is mostly
effective thermal insulation plasters with high porosity and controlled
capillary properties which assures improvement of thermal properties
construction, its diffusion openness towards the external environment
and suitable treatment capillary properties of preventing the
penetration of liquid moisture and salts thereof toward the outer
surface of the structure.
With respect to the current trend of reducing the energy
consumption of building structures and reduce the production of CO2
is necessary to develop capillary-active materials characterized by
their low density, low thermal conductivity while maintaining good
mechanical properties. The aim of researchers at the Faculty of Civil
Engineering, Brno University of Technology is the development and
study of hygrothermal behaviour of optimal materials for thermal
insulation and rehabilitation of building structures with the possible
use of alternative, less energy demanding binders in comparison with
conventional, frequently used binder, which represents cement.
The paper describes the evaluation of research activities aimed at
the development of thermal insulation and repair materials using
lightweight aggregate and alternative binders such as metakaolin and
finely ground fly ash.
Abstract: The thermal behavior of a large-scale, phase change material (PCM) enhanced building envelope system was studied in regard to the need for pre-fabricated construction in subtropical regions. The proposed large-scale envelope consists of a reinforced aluminum skin, insulation core, phase change material and reinforced gypsum board. The PCM impact on an energy efficiency of an enveloped room was resolved by validation of the EnergyPlus numerical scheme and optimization of a smart material location in the core. The PCM location was optimized by a minimization method of a cooling energy demand. It has been shown that there is good agreement between the test and simulation results. The optimal location of the PCM layer in Hong Kong summer conditions has been then recomputed for core thicknesses of 40, 60 and 80 mm. A non-dimensional value of the optimal PCM location was obtained to be same for all the studied cases and the considered external and internal conditions.
Abstract: Worldwide, most PILC MV underground cables in use
are approaching the end of their design life; hence, failures are likely
to increase. This paper studies the electric field and potential
distributions within the PILC insulted cable containing common
void-defect. The finite element model of the performance of the
belted PILC MV underground cable is presented. The variation of the
electric field stress within the cable using the Finite Element Method
(FEM) is concentrated. The effects of the void-defect within the
insulation are given. Outcomes will lead to deeper understanding of
the modeling of Paper Insulated Lead Covered (PILC) and electric
field response of belted PILC insulted cable containing void defect.
Abstract: In this research, waterglass based aerogel powder was
prepared by sol–gel process and ambient pressure drying. Inspired by
limited dust releasing, aerogel powder was introduced to the PET
electrospinning solution in an attempt to create required bulk and
surface structure for the nanofibers to improve their hydrophobic and
insulation properties. The samples evaluation was carried out by
measuring density, porosity, contact angle, heat transfer, FTIR, BET,
and SEM. According to the results, porous silica aerogel powder was
fabricated with mean pore diameter of 24 nm and contact angle of
145.9º. The results indicated the usefulness of the aerogel powder
confined into nanofibers to control surface roughness for
manipulating superhydrophobic nanowebs with water contact angle
of 147º. It can be due to a multi-scale surface roughness which was
created by nanowebs structure itself and nanofibers surface
irregularity in presence of the aerogels while a layer of fluorocarbon
created low surface energy. The wettability of a solid substrate is an
important property that is controlled by both the chemical
composition and geometry of the surface. Also, a decreasing trend in
the heat transfer was observed from 22% for the nanofibers without
any aerogel powder to 8% for the nanofibers with 4% aerogel
powder. The development of thermal insulating materials has become
increasingly more important than ever in view of the fossil energy
depletion and global warming that call for more demanding energysaving
practices.
Abstract: Aerated concrete is a load bearing construction
material, which has high heat insulation parameters. Walls can be
erected from aerated concrete masonry constructions and in perfect
circumstances additional heat insulation is not required. The most
common problem in aerated concrete heat insulation properties is the
humidity distribution throughout the cross section of the masonry
elements as well as proper and conducted drying process of the
aerated concrete construction because only dry aerated concrete
masonry constructions can reach high heat insulation parameters.
In order to monitor drying process of the masonry and detect
humidity distribution throughout the cross section of aerated concrete
masonry construction application of electrical impedance
spectrometry is applied. Further test results and methodology of this
non-destructive testing method is described in this paper.
Abstract: To practically apply vacuum insulation panels (VIPs)
to buildings or home appliances, VIPs have demanded long-term
lifespan with outstanding insulation performance. Service lives of
VIPs enveloped with Al-foil and three-layer Al-metallized envelope
are calculated. For Al-foil envelope, the service life is longer but edge
conduction is too large compared with the Al-metallized envelope. To
increase service life even more, the proposed double enveloping
method and metal-barrier-added enveloping method are further
analyzed. The service lives of the VIP to employ two enveloping
methods are calculated. Also, pressure increase and thermal insulation
performance characteristics are investigated. For the metalbarrier-
added enveloping method, effective thermal conductivity
increase with time is close to that of Al-foil envelope, especially, for
getter-inserted VIPs. For double enveloping method, if water vapor is
perfectly adsorbed, the effect of service life enhancement becomes
much greater. From these methods, the VIP can be guaranteed for
service life of more than 20 years.
Abstract: Vacuum Insulation Panel (VIP) can achieve very low
thermal conductivity by evacuating its inner space. Heat transfer in the
core materials of highly-evacuated VIP occurs by conduction through
the solid structure and radiation through the pore. The effect of various
scattering modes in combined conduction-radiation in VIP is
investigated through numerical analysis. The discrete ordinates
interpolation method (DOIM) incorporated with the commercial code
FLUENT® is employed. It is found that backward scattering is more
effective in reducing the total heat transfer while isotropic scattering is
almost identical with pure absorbing/emitting case of the same optical
thickness. For a purely scattering medium, the results agrees well with
additive solution with diffusion approximation, while a modified term
is added in the effect of optical thickness to backward scattering is
employed. For other scattering phase functions, it is also confirmed
that backwardly scattering phase function gives a lower effective
thermal conductivity. Thus the materials with backward scattering
properties, with radiation shields are desirable to lower the thermal
conductivity of VIPs.
Abstract: Vacuum insulation panel (VIP) is a promising thermal
insulator for buildings, refrigerator, LNG carrier and so on. In general,
it has the thermal conductivity of 2~4 mW/m·K. However, this thermal
conductivity is that measured at the center of VIP. The total effective
thermal conductivity of VIP is larger than this value due to the edge
conduction through the envelope. In this paper, the edge conduction of
VIP is examined theoretically, numerically and experimentally. To
confirm the existence of the edge conduction, numerical analysis is
performed for simple two-dimensional VIP model and a theoretical
model is proposed to calculate the edge conductivity. Also, the edge
conductivity is measured using the vacuum guarded hot plate and the
experiment is validated against numerical analysis. The results show
that the edge conductivity is dependent on the width of panel and
thickness of Al-foil. To reduce the edge conduction, it is recommended
that the VIP should be made as big as possible or made of thin Al film
envelope.
Abstract: The majority of contemporary insulation materials
commonly used in the building industry is made from non-renewable
raw materials; furthermore, their production often brings high energy
costs. A long-term trend as far as sustainable development is
concerned has been the reduction of energy and material demands of
building material production. One of the solutions is the possibility of
using easily renewable natural raw material sources which are
considerably more ecological and their production is mostly less
energy-consuming compared to the production of normal insulations
(mineral wool, polystyrene). The paper describes the results of
research focused on the development of thermal and acoustic
insulation materials based on natural fibres intended for floor
constructions. Given the characteristic open porosity of natural fibre
materials, the hygrothermal behaviour of the developed materials was
studied. Especially the influence of relative humidity and temperature
on thermal insulation properties was observed.
Abstract: Thermal insulation materials based on natural fibers
represent a very promising area of materials based on natural easy
renewable row sources. These materials may be in terms of the
properties of most competing synthetic insulations, but show
somewhat higher moisture sensitivity and thermal insulation
properties are strongly influenced by the density and orientation of
fibers. The paper described the problem of hygrothermal behavior of
thermal insulation materials based on natural plant and animal fibers.
This is especially the dependence of the thermal properties of these
materials on the type of fiber, bulk density, temperature, moisture and
the fiber orientation.
Abstract: When insulation and rehabilitation of structures is important to use quality building materials with high utility value. One potentially interesting and promising groups of construction materials in this area are advanced, thermally insulating plaster silicate based. With the present trend reduction of energy consumption of building structures and reducing CO2 emissions to be developed capillary-active materials that are characterized by their low density, low thermal conductivity while maintaining good mechanical properties.
The paper describes the results of research activities aimed at the development of thermal insulating and rehabilitation material ongoing at the Technical University in Brno, Faculty of Civil Engineering. The achieved results of this development will be the basis for subsequent experimental analysis of the influence of thermal and moisture loads developed on these materials.
Abstract: This paper presents the experimental results on role of
ionic solutions affect water treeing propagation in cross-linked
polyethylene insulation for high voltage cable. To study the water
treeing expansion due to the ionic solutions, discs of 4mm thickness
and 4cm diameter were taken from 115 kV XLPE insulation cable
and were used as test specimen in this study. Ionic solutions
composed of CuSO4, FeSO4, Na2SO4 and K2SO4 were used. Each
specimen was immersed in 0.1 mole ionic solutions and was tested
for 120 hrs. under a voltage stress at 7 kV AC rms, 1000 Hz. The
results show that Na2SO4 and CuSO4solutions play an important role
in the expansion of water treeing and cause degradation of the crosslinked
polyethylene (XLPE) in the presence of the applied electric
field.
Abstract: The modern energy-efficient houses are often founded on a thermal insulation (TI) layer placed under the building’s RC foundation slab.The purpose of the paper is to identify the potential problems of the buildings founded on TI layer from the seismic point of view. The two main goals of the study were to assess the seismic behavior of such buildings, and to search for the critical structural parameters affecting the response of the superstructure as well as of the extruded polystyrene (XPS) layer. As a test building a multi-storeyed RC frame structure with and without the XPS layer under the foundation slab has been investigated utilizing nonlinear dynamic (time-history) and static (pushover) analyses. The structural response has been investigated with reference to the following performance parameters: i) Building’s lateral roof displacements, ii) Edge compressive and shear strains of the XPS, iii) Horizontal accelerations of the superstructure, iv) Plastic hinge patterns of the superstructure, v) Part of the foundation in compression, and vi) Deformations of the underlying soil and vertical displacements of the foundation slab (i.e. identifying the potential uplift). The results have shown that in the case of higher and stiff structures lying on firm soil the use of XPS under the foundation slab might induce amplified structural peak responses compared to the building models without XPS under the foundation slab. The analysis has revealed that the superstructure as well as the XPS response is substantially affected by the stiffness of the foundation slab.