Abstract: In this paper, strontium ferrite (SrO.6Fe2O3) was
synthesized by the sol-gel auto-combustion process. The thermal
behavior of powder obtained from self-propagating combustion of
initial gel was evaluated by simultaneous differential thermal analysis
(DTA) and thermo gravimetric (TG), from room temperature to
1200°C. The as-burnt powder was calcined at various temperatures
from 700-900°C to achieve the single-phase Sr-ferrite. Phase
composition, morphology and magnetic properties were investigated
using X-ray diffraction (XRD), transmission electron microscopy
(TEM) and vibrating sample magnetometry (VSM) techniques.
Results showed that the single-phase and nano-sized hexagonal
strontium ferrite particles were formed at calcination temperature of
800°C with crystallite size of 27 nm and coercivity of 6238 Oe.
Abstract: Strontium hexaferrite (SrFe12O19; Sr-ferrite) is one of
the well-known materials for permanent magnets. In this study, Mtype
strontium ferrite was prepared by following the conventional
ceramic method from steelmaking by-product. Initial materials;
SrCO3 and by-product, were mixed together in the composition of
SrFe12O19 in different Sr/Fe ratios. The mixtures of these raw
materials were dry-milled for 6h. The blended powder was presintered
(i.e. calcination) at 1000°C for different times periods, then
cooled down to room temperature. These pre-sintered samples were
re-milled in a dry atmosphere for 1h and then fired at different
temperatures in atmospheric conditions, and cooled down to room
temperature. The produced magnetic powder has a dense hexagonal
grain shape structure. The calculated energy product values for the
produced samples ranged from 0.3 to 2.4 MGOe.
Abstract: Single-phase, high band gap energy Zn0.5Mg0.5O films were grown under oxygen pressure, using pulse laser deposition with a Zn0.5Mg0.5O target. Structural characterization studies revealed that the crystal structures of the ZnX-1MgXO films could be controlled via changes in the oxygen pressure. TEM analysis showed that the thickness of the deposited Zn1-xMgxO thin films was 50–75 nm. As the oxygen pressure increased, we found that one axis of the crystals did not show a very significant increase in the crystallization compared with that observed at low oxygen pressure. The X-ray diffraction peak intensity for the hexagonal-ZnMgO (002) plane increased relative to that for the cubic-ZnMgO (111) plane. The corresponding c-axis of the h-ZnMgO lattice constant increased from 5.141 to 5.148 Å, and the a-axis of the c-ZnMgO lattice constant decreased from 4.255 to 4.250 Å. EDX analysis showed that the Mg content in the mixed-phase ZnMgO films decreased significantly, from 54.25 to 46.96 at.%. As the oxygen pressure was increased from 100 to 150 mTorr, the absorption edge red-shifted from 3.96 to 3.81 eV; however, a film grown at the highest oxygen pressure tested here (200 mTorr).
Abstract: Rogowski coils are increasingly used for measurement
of AC and transient electric currents. Mostly used Rogowski coils
now are with circular or rectangular cores. In order to increase the
sensitivity of the measurement of Rogowski coil and perform smooth
wire winding, this paper studies the effect of increasing the mutual
inductance in order to increase the coil sensitivity by presenting the
calculation and simulation of a Rogowski coil with equilateral
hexagonal shaped core and comparing the resulted mutual inductance
with commonly used core shapes.
Abstract: In this paper, a design of ultra wideband (UWB) printed microstrip antennas that fed by microstrip transmission line were presented and printed on a substrate Taconic TLY-5 material with relative dielectric constant of 2.2. The proposed antennas were designed to cover the frequency range of 3.5 to 12 GHz. The antennas of printed patch shapes are rectangular, triangle/rectangular, hexagonal, and circular with the same dimensions of feeder and ground plane. The proposed antennas were simulated using a package of CST microwave studio in the 2 to 12 GHz operating frequency range. Simulation results and comparison for return loss (S11), radiation patterns, and voltage standing wave ratio (VSWR) were presented and discussed over the UWB frequency.
Abstract: Shape and form of the watermelon fruits are important factors to save spaces and reducing damage during storing of the fruits. In order to save spaces and prevent fruit damage in watermelon the following experiment was carried out in the farm. The fruits were boxed when they were approximately one cm less than the box diameter. The cubic, hexagonal forms were compared in this research. To do this, different boxes were designed with different holes on the sides to holes the watermelons fruits for shaping. The shapes of the boxes were hexagonal and cubic. The boxes holes sizes were the same with 10mm diameter each. Each side of the boxes had different holes including: without holes to 75 holes. The result showed that the best shape for watermelon storing to save space and prevent fruit damage was hexagonal form. The percentages of the fruit damage were 33 to 80 respectively.
Abstract: In this paper, the periodic surveillance scheme has
been proposed for any convex region using mobile wireless sensor
nodes. A sensor network typically consists of fixed number of
sensor nodes which report the measurements of sensed data such as
temperature, pressure, humidity, etc., of its immediate proximity
(the area within its sensing range). For the purpose of sensing an
area of interest, there are adequate number of fixed sensor
nodes required to cover the entire region of interest. It implies
that the number of fixed sensor nodes required to cover a given
area will depend on the sensing range of the sensor as well as
deployment strategies employed. It is assumed that the sensors to
be mobile within the region of surveillance, can be mounted on
moving bodies like robots or vehicle. Therefore, in our
scheme, the surveillance time period determines the number of
sensor nodes required to be deployed in the region of interest.
The proposed scheme comprises of three algorithms namely:
Hexagonalization, Clustering, and Scheduling, The first algorithm
partitions the coverage area into fixed sized hexagons that
approximate the sensing range (cell) of individual sensor node.
The clustering algorithm groups the cells into clusters, each of
which will be covered by a single sensor node. The later
determines a schedule for each sensor to serve its respective cluster.
Each sensor node traverses all the cells belonging to the cluster
assigned to it by oscillating between the first and the last cell for
the duration of its life time. Simulation results show that our
scheme provides full coverage within a given period of time using
few sensors with minimum movement, less power consumption,
and relatively less infrastructure cost.
Abstract: Most HWRs currently use natural uranium fuel. Using enriched uranium fuel results in a significant improvement in fuel cycle costs and uranium utilization. On the other hand, reactivity changes of HWRs over the full range of operating conditions from cold shutdown to full power are small. This reduces the required reactivity worth of control devices and minimizes local flux distribution perturbations, minimizing potential problems due to transient local overheating of fuel. Analyzing heavy water effectiveness on neutronic parameters such as enrichment requirements, peaking factor and reactivity is important and should pay attention as primary concepts of a HWR core designing. Two nuclear nuclear reactors of CANDU-type and hexagonal-type reactor cores of 33 fuel assemblies and 19 assemblies in 1.04 P/D have been respectively simulated using MCNP-4C code. Using heavy water and light water as moderator have been compared for achieving less reactivity insertion and enrichment requirements. Two fuel matrixes of (232Th/235U)O2 and (238/235U)O2 have been compared to achieve more economical and safe design. Heavy water not only decreased enrichment needs, but it concluded in negative reactivity insertions during moderator density variations. Thorium oxide fuel assemblies of 2.3% enrichment loaded into the core of heavy water moderator resulted in 0.751 fission to absorption ratio and peaking factor of 1.7 using. Heavy water not only provides negative reactivity insertion during temperature raises which changes moderator density but concluded in 2 to 10 kg reduction of enrichment requirements, depend on geometry type.
Abstract: In this study, ZnO nano rods and ZnO ultrafine particles were synthesized by Gel-casting method. The synthesized ZnO powder has a hexagonal zincite structure. The ZnO aggregates with rod-like morphology are typically 1.4 μm in length and 120 nm in diameter, which consist of many small nanocrystals with diameters of 10 nm. Longer wires connected by many hexahedral ZnO nanocrystals were obtained after calcinations at the temperature over 600° C.The crystalline structures and morphologies of the powder have been characterized by X-ray diffraction(XRD) and Scaning electron microscopy (SEM).The result shows that the different preparation conditions such as concentration H2O, calcinations time and calcinations temperature have a lot of influences upon the properties of nano ZnO powders, an increase in the temperature of the calcinations results in an increase of the grain size and also the increase of the calcinations time in high temperature makes the size of the grains bigger. The existences of extra watter prevent nano grains from improving like rod morphology. We have obtained the smallest grain size of ZnO powder by controlling the process conditions. Finally In a suitable condition, a novel nanostructure, namely bi-rod-like ZnO nano rods was found which is different from known ZnO nanostructures.
Abstract: Honeycomb sandwich panels are increasingly used in the construction of space vehicles because of their outstanding strength, stiffness and light weight properties. However, the use of honeycomb sandwich plates comes with difficulties in the design process as a result of the large number of design variables involved, including composite material design, shape and geometry. Hence, this work deals with the presentation of an optimal design of hexagonal honeycomb sandwich structures subjected to space environment. The optimization process is performed using a set of algorithms including the gravitational search algorithm (GSA). Numerical results are obtained and presented for a set of algorithms. The results obtained by the GSA algorithm are much better compared to other algorithms used in this study.
Abstract: For about two decades scientists have been
developing techniques for enhancing the quality of medical images
using Fourier transform, DWT (Discrete wavelet transform),PDE
model etc., Gabor wavelet on hexagonal sampled grid of the images
is proposed in this work. This method has optimal approximation
theoretic performances, for a good quality image. The computational
cost is considerably low when compared to similar processing in the
rectangular domain. As X-ray images contain light scattered pixels,
instead of unique sigma, the parameter sigma of 0.5 to 3 is found to
satisfy most of the image interpolation requirements in terms of high
Peak Signal-to-Noise Ratio (PSNR) , lower Mean Squared Error
(MSE) and better image quality by adopting windowing technique.
Abstract: A simple approach is demonstrated for growing large
scale, nearly vertically aligned ZnO nanowire arrays by thermal
oxidation method. To reveal effect of temperature on growth and
physical properties of the ZnO nanowires, gold coated zinc substrates
were annealed at 300 °C and 400 °C for 4 hours duration in air. Xray
diffraction patterns of annealed samples indicated a set of well
defined diffraction peaks, indexed to the wurtzite hexagonal phase of
ZnO. The scanning electron microscopy studies show formation of
ZnO nanowires having length of several microns and average of
diameter less than 500 nm. It is found that the areal density of wires
is relatively higher, when the annealing is carried out at higher
temperature i.e. at 400°C. From the field emission studies, the values
of the turn-on and threshold field, required to draw emission current
density of 10 μA/cm2 and 100 μA/cm2 are observed to be 1.2 V/μm
and 1.7 V/μm for the samples annealed at 300 °C and 2.9 V/μm and
3.7 V/μm for that annealed at 400 °C, respectively. The field
emission current stability, investigated over duration of more than 2
hours at the preset value of 1 μA, is found to be fairly good in both
cases. The simplicity of the synthesis route coupled with the
promising field emission properties offer unprecedented advantage
for the use of ZnO field emitters for high current density
applications.
Abstract: Alumina matrix composites with addition of hexagonal boron nitride (hBN), acting as solid lubricant, were produced. Main purpose of solid lubricants is to dispose the necessity of using cooling lubricants in machining process. Hot pressing was used as a consolidating process for Al2O3-x%wt.hBN (x=1/ 2,5/ 5 /7,5 /10) composites. Properties of sinters such as relative density, hardness, Young-s modulus and fracture toughness were examined. Obtained samples characterize by high relative density. Hardness and fracture toughness values allow the use of alumina – hBN composites for machining steels even in hardened condition. However it was observed that high weight content of hBN can negatively influence the mechanical properties of composites.
Abstract: In our recent study, we have used ZnO nanoparticles assisted with UV light irradiation to investigate the photocatalytic degradation of Phenol Red (PR). The ZnO photocatalyst was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), specific surface area analysis (BET) and UVvisible spectroscopy. X-ray diffractometry result for the ZnO nanoparticles exhibit normal crystalline phase features. All observed peaks can be indexed to the pure hexagonal wurtzite crystal structures, with the space group of P63mc. There are no other impurities in the diffraction peak. In addition, TEM measurement shows that most of the nanoparticles are rod-like and spherical in shape and fairly monodispersed. A significant degradation of the PR was observed when the catalyst was added into the solution even without the UV light exposure. In addition, the photodegradation increases with the photocatalyst loading. The surface area of the ZnO nanomaterials from the BET measurement was 11.9 m2/g. Besides the photocatalyst loading, the effect of some parameters on the photodegradation efficiency such as initial PR concentration and pH were also studied.
Abstract: In the study of honeycomb crushing under quasistatic loading, two parameters are important, the mean crushing stress and the wavelength of the folding mode. The previous theoretical models did not consider the true cylindrical curvature effects and the flow stress in the folding mode of honeycomb material. The present paper introduces a modification on Wierzbicki-s model based on considering two above mentioned parameters in estimating the mean crushing stress and the wavelength through implementation of the energy method. Comparison of the results obtained by the new model and Wierzbicki-s model with existing experimental data shows better prediction by the model presented in this paper.
Abstract: The present work is motivated by the idea that the
layer deformation in anisotropic elasticity can be estimated from the
theory of interfacial dislocations. In effect, this work which is an
extension of a previous approach given by one of the authors
determines the anisotropic displacement fields and the critical
thickness due to a complex biperiodic network of MDs lying just
below the free surface in view of the arrangement of dislocations.
The elastic fields of such arrangements observed along interfaces
play a crucial part in the improvement of the physical properties of
epitaxial systems. New results are proposed in anisotropic elasticity
for hexagonal networks of MDs which contain intrinsic and extrinsic
stacking faults. We developed, using a previous approach based on
the relative interfacial displacement and a Fourier series formulation
of the displacement fields, the expressions of elastic fields when
there is a possible dissociation of MDs. The numerical investigations
in the case of the observed system Si/(111)Si with low twist angles
show clearly the effect of the anisotropy and thickness when the
misfit networks are dissociated.
Abstract: Ciprofloxacin (CIP) and Carbamazepine (CBZ), nonbiodegradable pharmaceutical residues, were become emerging pollutants in several aquatic environments. The objectives of this research were to study the possibility to recover these pharmaceuticals residues from pharmaceutical wastewater by increasing the selective adsorption on synthesized functionalized porous silicate, comparing with powdered activated carbon (PAC). Hexagonal mesoporous silicate (HMS), functionalized HMSs (3- aminopropyltriethoxy, 3- mercaptopropyltrimethoxy and noctyldimethyl) were synthesized and characterized physico-chemical characteristics. Obtained adsorption kinetics and isotherms showed that 3-mercaptopropyltrimethoxy functional groups grafted on HMS provided highest CIP and CBZ adsorption capacities; however, it was still lower than that of PAC. The kinetic results were compatible with pseudo-second order. The hydrophobicity and hydrogen bonding might play a key role on the adsorption. Furthermore, the capacities were affected by varying pH values due to the strength of hydrogen bonding between targeted compounds and adsorbents. Electrostatic interaction might not affect the adsorption capacities.
Abstract: The stab resistance performance of newly developed
fabric composites composed of hexagonal paper honeycombs, filled
with shear thickening fluid (STF), and woven Kevlar® fabric or
UHMPE was investigated in this study. The STF was prepared by
dispersing submicron SiO2 particles into polyethylene glycol (PEG).
Our results indicate that the STF-Kevlar composite possessed lower
penetration depth than that of neat Kevlar. In other words, the
STF-Kevlar composite can attain the same energy level in
stab-resistance test with fewer layers of Kevlar fabrics than that of the
neat Kevlar fabrics. It also indicates that STF can be used for the
fabrication of flexible body armors and can provide improved
protection against stab threats. We found that the stab resistance of the
STF-Kevlar composite increases with the increase of SiO2
concentration in STF. Moreover, the silica particles functionalized
with silane coupling agent can further improve the stab resistance.
Abstract: Double heterogeneity of randomly located pebbles in
the core and Coated Fuel Particles (CFPs) in the pebbles are specific
features in pebble bed reactors and usually, because of difficulty to
model with MCNP code capabilities, are neglected. In this study,
characteristics of HTR-10, Tsinghua University research reactor, are
used and not only double heterogeneous but also truncated CFPs and
Pebbles are considered.Firstly, 8335 CFPs are distributed randomly
in a pebble and then the core of reactor is filled with those pebbles
and graphite pebbles as moderator such that 57:43 ratio of fuel and
moderator pebbles is established.Finally, four different core
configurations are modeled. They are Simple Cubic (SC) structure
with truncated pebbles,SC structure without truncated pebble, and
Simple Hexagonal(SH) structure without truncated pebbles and SH
structure with truncated pebbles. Results like effective multiplication
factor (Keff), critical height,etc. are compared with available data.
Abstract: The purpose of this paper is to perform a multidisciplinary design and analysis (MDA) of honeycomb panels used in the satellites structural design. All the analysis is based on clamped-free boundary conditions. In the present work, detailed finite element models for honeycomb panels are developed and analysed. Experimental tests were carried out on a honeycomb specimen of which the goal is to compare the previous modal analysis made by the finite element method as well as the existing equivalent approaches. The obtained results show a good agreement between the finite element analysis, equivalent and tests results; the difference in the first two frequencies is less than 4% and less than 10% for the third frequency. The results of the equivalent model presented in this analysis are obtained with a good accuracy. Moreover, investigations carried out in this research relate to the honeycomb plate modal analysis under several aspects including the structural geometrical variation by studying the various influences of the dimension parameters on the modal frequency, the variation of core and skin material of the honeycomb. The various results obtained in this paper are promising and show that the geometry parameters and the type of material have an effect on the value of the honeycomb plate modal frequency.