Abstract: With the growth of modern civilization and
industrialization in worldwide, the demand for energy is increasing
day by day. Majority of the world-s energy needs are met through
fossil fuels and natural gas. As a result the amount of fossil fuels is
on diminishing from year to year. Since the fossil fuel is nonrenewable,
so fuel price is gouging as a consequence of spiraling
demand and diminishing supply. At present the power generation of
our country is mainly depends on imported fossil fuels. To reduce the
dependency on imported fuel, the use of renewable sources has
become more popular. In Bangladesh coconut is widely growing tree.
Especially in the southern part of the country a large area will be
found where coconut tree is considered as natural asset. So, our
endeavor was to use the coconut oil as a renewable and alternative
fuel. This article shows the prospect of coconut oil as a renewable
and alternative fuel of diesel fuel. Since diesel engine has a versatile
uses including small electricity generation, an experimental set up is
then made to study the performance of a small diesel engine using
different blends of bio diesel converted from coconut oil. It is found
that bio diesel has slightly different properties than diesel. With
biodiesel the engine is capable of running without difficulty.
Different blends of bio diesel (i.e. B80, B60, and B 50 etc.) have
been used to avoid complicated modification of the engine or the fuel
supply system. Finally, a comparison of engine performance for
different blends of biodiesel has been carried out to determine the
optimum blend for different operating conditions.
Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: With the growth of electricity generation from gas
energy gas pipeline reliability can substantially impact the electric
generation. A physical disruption to pipeline or to a compressor
station can interrupt the flow of gas or reduce the pressure and lead
to loss of multiple gas-fired electric generators, which could
dramatically reduce the supplied power and threaten the power
system security. Gas pressure drops during peak loading time on
pipeline system, is a common problem in network with no enough
transportation capacity which limits gas transportation and causes
many problem for thermal domain power systems in supplying their
demand. For a feasible generation scheduling planning in networks
with no sufficient gas transportation capacity, it is required to
consider gas pipeline constraints in solving the optimization problem
and evaluate the impacts of gas consumption in power plants on gas
pipelines operating condition. This paper studies about operating of
gas fired power plants in critical conditions when the demand of gas
and electricity peak together. An integrated model of gas and electric
model is used to consider the gas pipeline constraints in the economic
dispatch problem of gas-fueled thermal generator units.
Abstract: Self-propelled forage harvesters in the 850
horsepower range were tested over three years for fuel consumption,
throughput and quality of chop for corn silage. Cut length had a
significant effect on fuel consumption, throughput and some aspects
of chop quality. Measure cut length was often different than
theoretical length of cut. Where cut length was equivalent fuel
consumption and throughput were equivalent across brands.
Shortening cut length from 17 to 11mm increases fuel consumption
53 percent measured as Mg of silage harvested per gallon of fuel used
and a 42 percent decrease in capacity as tons of fresh material per
hour run time.
Abstract: While the form of crises may change, their essence
remains the same (such as a cycle of abundant liquidity, rapid credit
growth, and a low-inflation environment followed by an asset-price
bubble). The current market turbulence began in mid-2000s when the
US economy shifted to imbalanced both internal and external
macroeconomic positions. We see two key causes of these problems
– loose US monetary policy in early 2000s and US government
guarantees issued on the securities by government-sponsored
enterprises what was further fueled by financial innovations such as
structured credit products. We have discovered both negative and
positive lessons deriving from this crisis and divided the negative
lessons into three groups: financial products and valuation, processes
and business models, and strategic issues. Moreover, we address key
risk management lessons and exit strategies derived from the current
crisis and recommend policies that should help diminish the negative
impact of future potential crises.
Abstract: A simple mobile engine-driven pneumatic paddy
collector made of locally available materials using local
manufacturing technology was designed, fabricated, and tested for
collecting and bagging of paddy dried on concrete pavement. The
pneumatic paddy collector had the following major components:
radial flat bladed type centrifugal fan, power transmission system,
bagging area, frame and the conveyance system. Results showed
significant differences on the collecting capacity, noise level, and fuel
consumption when rotational speed of the air mover shaft was varied.
Other parameters such as collecting efficiency, air velocity,
augmented cracked grain percentage, and germination rate were not
significantly affected by varying rotational speed of the air mover
shaft. The pneumatic paddy collector had a collecting efficiency of
99.33 % with a collecting capacity of 2685.00 kg/h at maximum
rotational speed of centrifugal fan shaft of about 4200 rpm. The
machine entailed an investment cost of P 62,829.25. The break-even
weight of paddy was 510,606.75 kg/yr at a collecting cost of 0.11
P/kg of paddy. Utilizing the machine for 400 hours per year
generated an income of P 23,887.73. The projected time needed to
recover cost of the machine based on 2685 kg/h collecting capacity
was 2.63 year.
Abstract: The presented article deals with the description of a
numerical model of a corridor at a Central Interim Spent Fuel Storage
Facility (hereinafter CISFSF). The model takes into account the
effect of air flows on the temperature of stored waste. The
computational model was implemented in the ANSYS/CFX
programming environment in the form of a CFD task solution, which
was compared with an approximate analytical calculation. The article
includes a categorization of the individual alternatives for the
ventilation of such underground systems. The aim was to evaluate a
ventilation system for a CISFSF with regard to its stability and
capacity to provide sufficient ventilation for the removal of heat
produced by stored casks with spent nuclear fuel.
Abstract: Component handling system is one of the important sub systems of Prototype Fast Breeder Reactor (PFBR) used for fuel handling. Core handling system is again a sub system of component handling system. Core handling system consists of in-vessel and ex-vessel subassembly handling. In-vessel core handling involves transfer arm, large rotatable plug and small rotatable plug operations. Modeling and simulation of in-vessel core handling is a part of development of Prototype Fast Breeder Reactor Operator Training Simulator. This paper deals with simulation and modeling of operations of transfer arm, large rotatable plug and small rotatable plug needed for in-vessel core handling. Process modeling was developed in house using platform independent Cµ code with OpenGL (Open Graphics Library). The control logic models and virtual panel were modeled using simulation tool.
Abstract: A phorbol-12-myristate-13-acetate (TPA) is a synthetic analogue of phorbol ester (PE), a natural toxic compound of Euphorbiaceae plant. The oil extracted from plants of this family is useful source for primarily biofuel. However this oil might also be used as a foodstuff due to its significant nutrition content. The limitations for utilizing the oil as a foodstuff are mainly due to a toxicity of PE. Currently, a majority of PE detoxification processes are expensive as include multi steps alcohol extraction sequence.
Ozone is considered as a strong oxidative agent. It reacts with PE by attacking the carbon-carbon double bond of PE. This modification of PE molecular structure yields a non toxic ester with high lipid content.
This report presents data on development of simple and cheap PE detoxification process with water application as a buffer and ozone as reactive component. The core of this new technique is an application for a new microscale plasma unit to ozone production and the technology permits ozone injection to the water-TPA mixture in form of microbubbles.
The efficacy of a heterogeneous process depends on the diffusion coefficient which can be controlled by contact time and interfacial area. The low velocity of rising microbubbles and high surface to volume ratio allow efficient mass transfer to be achieved during the process. Direct injection of ozone is the most efficient way to process with such highly reactive and short lived chemical.
Data on the plasma unit behavior are presented and the influence of gas oscillation technology on the microbubble production mechanism has been discussed. Data on overall process efficacy for TPA degradation is shown.
Abstract: This paper considers the influence of promotion
instruments for renewable energy sources (RES) on a multi-energy
modeling framework. In Europe, so called Feed-in Tariffs are
successfully used as incentive structures to increase the amount of
energy produced by RES. Because of the stochastic nature of large
scale integration of distributed generation, many problems have
occurred regarding the quality and stability of supply. Hence, a
macroscopic model was developed in order to optimize the power
supply of the local energy infrastructure, which includes electricity,
natural gas, fuel oil and district heating as energy carriers. Unique
features of the model are the integration of RES and the adoption of
Feed-in Tariffs into one optimization stage. Sensitivity studies are
carried out to examine the system behavior under changing profits
for the feed-in of RES. With a setup of three energy exchanging
regions and a multi-period optimization, the impact of costs and
profits are determined.
Abstract: Electric vehicles are considered as technology which
can significantly reduce the problems related to road transport such
as increasing GHG emissions, air pollutions and energy import
dependency.
The core objective of this paper is to analyze the current energetic,
ecological and economic characteristics of different types of electric
vehicles.
The major conclusions of this analysis are: The high investments
cost are the major barrier for broad market breakthrough of battery
electric vehicles and fuel cell vehicles. For battery electric vehicles
also the limited driving range states a key obstacle. The analyzed
hybrids could in principle serve as a bridging technology. However,
due to their tank-to-wheel emissions they cannot state a proper
solution for urban areas.
Finally, the most important perception is that also battery electric
vehicles and fuel cell vehicles are environmentally benign solution if
the primary fuel source is renewable.
Abstract: This paper presents the applications of computational intelligence techniques to economic load dispatch problems. The fuel cost equation of a thermal plant is generally expressed as continuous quadratic equation. In real situations the fuel cost equations can be discontinuous. In view of the above, both continuous and discontinuous fuel cost equations are considered in the present paper. First, genetic algorithm optimization technique is applied to a 6- generator 26-bus test system having continuous fuel cost equations. Results are compared to conventional quadratic programming method to show the superiority of the proposed computational intelligence technique. Further, a 10-generator system each with three fuel options distributed in three areas is considered and particle swarm optimization algorithm is employed to minimize the cost of generation. To show the superiority of the proposed approach, the results are compared with other published methods.
Abstract: The composition, vapour pressure, and heat capacity
of nine biodiesel fuels from different sources were measured. The
vapour pressure of the biodiesel fuels is modeled assuming an ideal
liquid phase of the fatty acid methyl esters constituting the fuel. New
methodologies to calculate the vapour pressure and ideal gas and
liquid heat capacities of the biodiesel fuel constituents are proposed.
Two alternative optimization scenarios are evaluated: 1) vapour
pressure only; 2) vapour pressure constrained with liquid heat
capacity. Without physical constraints, significant errors in liquid
heat capacity predictions were found whereas the constrained
correlation accurately fit both vapour pressure and liquid heat
capacity.
Abstract: Eco-driving allows the driver to optimize his/her behaviour in order to achieve several types of benefits: reducing pollution emissions, increasing road safety, and fuel saving. One of the main rules for adopting eco-driving is to anticipate the traffic events by avoiding strong acceleration or braking and maintaining a steady speed when possible. Therefore, drivers have to comply with speed limits and time headway. The present study explored the role of three types of motivation and social norms in predicting French drivers- intentions to comply with speed limits and time headway as eco-driving practices as well as examine the variations according to gender and age. 1234 drivers with ages between 18 and 75 years old filled in a questionnaire which was presented as part of an online survey aiming to better understand the drivers- road habits. It included items assessing: a) behavioural intentions to comply with speed limits and time headway according to three types of motivation: reducing pollution emissions, increasing road safety, and fuel saving, b) subjective and descriptive social norms regarding the intention to comply with speed limits and time headway, and c) sociodemographical variables. Drivers expressed their intention to frequently comply with speed limits and time headway in the following 6 months; however, they showed more intention to comply with speed limits as compared to time headway regardless of the type of motivation. The subjective injunctive norms were significantly more important in predicting drivers- intentions to comply with speed limits and time headway as compared to the descriptive norms. In addition, the most frequently reported type of motivation for complying with speed limits and time headway was increasing road safety followed by fuel saving and reducing pollution emissions, hence underlining a low motivation to practice eco-driving. Practical implications of the results are discussed.
Abstract: A co-generation system in automobile can improve
thermal efficiency of vehicle in some degree. The waste heat from the
engine exhaust and coolant is still attractive energy source that reaches
around 60% of the total energy converted from fuel. To maximize the
effectiveness of heat exchangers for recovering the waste heat, it is
vital to select the most suitable working fluid for the system, not to
mention that it is important to find the optimum design for the heat
exchangers. The design of heat exchanger is out of scoop of this study;
rather, the main focus has been on the right selection of working fluid
for the co-generation system. Simulation study was carried out to find
the most suitable working fluid that can allow the system to achieve
the optimum efficiency in terms of the heat recovery rate and thermal
efficiency.
Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: Regenerative Thermal Oxidizer (RTO) is one of the
best solutions for removal of Volatile Organic Compounds (VOC)
from industrial processes. In the RTO, VOC in a raw gas are usually
decomposed at 950-1300 K and the combustion heat of VOC is
recovered by regenerative heat exchangers charged with ceramic
honeycombs. The optimization of the treatment of VOC leads to the
reduction of fuel addition to VOC decomposition, the minimization of
CO2 emission and operating cost as well.
In the present work, the thermal efficiency of the RTO was
investigated experimentally in a pilot-scale RTO unit using toluene as
a typical representative of VOC. As a result, it was recognized that the
radiative heat transfer was dominant in the preheating process of a raw
gas when the gas flow rate was relatively low. Further, it was found
that a minimum heat exchanger volume to achieve self combustion of
toluene without additional heating of the RTO by fuel combustion was
dependent on both the flow rate of a raw gas and the concentration of
toluene. The thermal efficiency calculated from fuel consumption and
the decomposed toluene ratio, was found to have a maximum value of
0.95 at a raw gas mass flow rate of 1810 kg·h-1 and honeycombs height
of 1.5m.
Abstract: Losses reduction initiatives in distribution systems
have been activated due to the increasing cost of supplying
electricity, the shortage in fuel with ever-increasing cost to produce
more power, and the global warming concerns. These initiatives have
been introduced to the utilities in shape of incentives and penalties.
Recently, the electricity distribution companies in Oman have been
incentivized to reduce the distribution technical and non-technical
losses with an equal annual reduction rate for 6 years. In this paper,
different techniques for losses reduction in Mazoon Electricity
Company (MZEC) are addressed. In this company, high numbers of
substation and feeders were found to be non-compliant with the
Distribution System Security Standard (DSSS). Therefore, 33
projects have been suggested to bring non-complying 29 substations
and 28 feeders to meet the planed criteria and to comply with the
DSSS. The largest part of MZEC-s network (South Batinah region)
was modeled by ETAP software package. The model has been
extended to implement the proposed projects and to examine their
effects on losses reduction. Simulation results have shown that the
implementation of these projects leads to a significant improvement
in voltage profile, and reduction in the active and the reactive power
losses. Finally, the economical analysis has revealed that the
implementation of the proposed projects in MZEC leads to an annual
saving of about US$ 5 million.
Abstract: Salinity level may affect early development of
biofuel feedstock crops. The biofuel feedstock crops canola
(Brassica napus L.), sorghum [Sorghum bicolor (L.) Moench], and
sunflower (Helianthus annuus L.); and the potential feedstock crop
sweet corn (Zea mays L.) were planted in media in pots and treated
with aqueous solutions of 0, 0.1, 0.5 and 1.0 M NaCl once at: 1)
planting; 2) 7-10 days after planting or 3) first true leaf expansion.
An additional treatment (4) comprised of one-half strength of the 0.1,
0.5 and 1.0 M (concentrations 0.05, 0.25, 0.5 M at each application)
was applied at first true leaf expansion and four days later. Survival
of most crops decreased below 90% above 0.5 M; survival of canola
decreased above 0.1 M. Application timing had little effect on crop
survival. For canola root fresh and dry weights improved when
application was at plant emergence; for sorghum top and root fresh
weights improved when the split application was used. When
application was at planting root dry weight was improved over most
other applications. Sunflower top fresh weight was among the
highest when saline solutions were split and top dry weight was
among the highest when application was at plant emergence. Sweet
corn root fresh weight was improved when the split application was
used or application was at planting. Sweet corn root dry weight was
highest when application was at planting or plant emergence. Even at
high salinity rates survival rates greater than what might be expected
occurred. Plants that survived appear to be able to adjust to saline
during the early stages of development.
Abstract: An aqueous methanol sensor for use in direct
methanol fuel cells (DMFCs) applications is demonstrated; the
methanol sensor is built using dispersed single-walled carbon
nanotubes (SWCNTs) with Nafion117 solution to detect the methanol
concentration in water. The study is aimed at the potential use of the
carbon nanotubes array as a methanol sensor for direct methanol fuel
cells (DMFCs). The concentration of methanol in the fuel circulation
loop of a DMFC system is an important operating parameter, because
it determines the electrical performance and efficiency of the fuel cell
system. The sensor is also operative even at ambient temperatures
and responds quickly to changes in the concentration levels of the
methanol. Such a sensor can be easily incorporated into the methanol
fuel solution flow loop in the DMFC system.