Abstract: This work is to study a roll of the fluctuating density
gradient in the compressible flows for the computational fluid dynamics
(CFD). A new anisotropy tensor with the fluctuating density
gradient is introduced, and is used for an invariant modeling technique
to model the turbulent density gradient correlation equation derived
from the continuity equation. The modeling equation is decomposed
into three groups: group proportional to the mean velocity, and that
proportional to the mean strain rate, and that proportional to the mean
density. The characteristics of the correlation in a wake are extracted
from the results by the two dimensional direct simulation, and shows
the strong correlation with the vorticity in the wake near the body.
Thus, it can be concluded that the correlation of the density gradient
is a significant parameter to describe the quick generation of the
turbulent property in the compressible flows.
Abstract: Bubble columns have a variety of applications in
absorption, bio-reactions, catalytic slurry reactions, and coal
liquefaction; because they are simple to operate, provide good heat
and mass transfer, having less operational cost. The use of
Computational Fluid Dynamics (CFD) for bubble column becomes
important, since it can describe the fluid hydrodynamics on both local
and global scale. Euler- Euler two-phase fluid model has been used to
simulate two-phase (air and water) transient up-flow in bubble
column (15cm diameter) using FLUENT6.3. These simulations and
experiments were operated over a range of superficial gas velocities
in the bubbly flow and churn turbulent regime (1 to16 cm/s) at
ambient conditions. Liquid velocity was varied from 0 to 16cm/s. The
turbulence in the liquid phase is described using the standard k-ε
model. The interactions between the two phases are described
through drag coefficient formulations (Schiller Neumann). The
objectives are to validate CFD simulations with experimental data,
and to obtain grid-independent numerical solutions. Quantitatively
good agreements are obtained between experimental data for hold-up
and simulation values. Axial liquid velocity profiles and gas holdup
profiles were also obtained for the simulation.
Abstract: Downward turbulent bubbly flows in pipes were
modeled using computational fluid dynamics tools. The
Hydrodynamics, phase distribution and turbulent structure of twophase
air-water flow in a 57.15 mm diameter and 3.06 m length
vertical pipe was modeled by using the 3-D Eulerian-Eulerian
multiphase flow approach. Void fraction, liquid velocity and
turbulent fluctuations profiles were calculated and compared against
experimental data. CFD results are in good agreement with
experimental data.
Abstract: This study experimentally investigates the heat transfer effects of forced convection and natural convection under different substrate openings design. A computational fluid dynamics (CFD) model was established and implemented to verify and explain the experimental results and heat transfer behavior. It is found that different opening position will destroy the growth of the boundary layer on substrates to alter the cooling ability for both forced under low Reynolds number and natural convection. Nevertheless, having too many opening may reduce heat conduction and affect the overall heat transfer performance. This study provides future researchers with a guideline on designing and electronic package manufacturing.
Abstract: In this work, axisymetric CFD simulation of fixed bed
GTL reactor has been conducted, using computational fluid dynamics
(CFD). In fixed bed CFD modeling, when N (tube-to-particle
diameter ratio) has a large value, it is common to consider the packed
bed as a porous media. Synthesis gas (a mixture of predominantly
carbon monoxide and hydrogen) was fed to the reactor. The reactor
length was 20 cm, divided to three sections. The porous zone was in
the middle section of the reactor. The model equations were solved
employing finite volume method. The effects of particle diameter,
bed voidage, fluid velocity and bed length on pressure drop have
been investigated. Simulation results showed these parameters could
have remarkable impacts on the reactor pressure drop.
Abstract: We consider here the subsonic impinging jet
representing the flow field of a vertical take-off aircraft or the initial
stage of rocket launching. Implicit Large-Eddy Simulation (ILES) is
used to calculate the time-dependent flow field and the radiate sound
pressure associated with jet impinging. With proper boundary
treatments and high-order numerical scheme, the near field sound
pressure is successfully obtained. Results are presented for both a
rectangular as well a circular jet.
Abstract: Spray chilling using air-mist nozzles has received
much attention in the food processing industry because of the
benefits it has shown over forced air convection. These benefits
include an increase in the heat transfer coefficient and a reduction in
the water loss by the product during cooling. However, few studies
have simulated the heat transfer and aerodynamics phenomena of the
air-mist chilling process for optimal operating conditions. The study
provides insight into the optimal conditions for spray impaction, heat
transfer efficiency and control of surface flooding. A computational
fluid dynamics model using a two-phase flow composed of water
droplets injected with air is developed to simulate the air-mist
chilling of food products. The model takes into consideration
droplet-to-surface interaction, water-film accumulation and surface
runoff. The results of this study lead to a better understanding of the
heat transfer enhancement, water conservation, and to a clear
direction for the optimal design of air-mist chilling systems that can
be used in commercial applications in the food and meat processing
industries.
Abstract: Aircraft propulsion systems often use Y-shaped
subsonic diffusing ducts as twin air-intakes to supply the ambient air
into the engine compressor for thrust generation. Due to space
constraint, the diffusers need to be curved, which causes severe flow
non-uniformity at the engine face. The present study attempt to
control flow in a mild-curved Y-duct diffuser using trapezoidalshaped
vortex generators (VG) attached on either both the sidewalls
or top and bottom walls of the diffuser at the inflexion plane. A
commercial computational fluid dynamics (CFD) code is modified
and is used to simulate the effects of SVG in flow of a Y-duct
diffuser. A few experiments are conducted for CFD code validation,
while the rest are done computationally. The best combination of Yduct
diffuser is found with VG-2 arranged in co-rotating sequence
and attached to both the sidewalls, which ensures highest static
pressure recovery, lowest total pressure loss, minimum flow
distortion and less flow separation in Y-duct diffuser. The decrease in
VG height while attached to top and bottom walls further improves
axial flow uniformity at the diffuser outlet by a great margin as
compared to the bare duct.
Abstract: Scaffolds play a key role in tissue engineering and can be produced in many different ways depending on the applications and the materials used. Most researchers used an experimental trialand- error approach into new biomaterials but computer simulation applied to tissue engineering can offer a more exhaustive approach to test and screen out biomaterials. This paper develops the model of scaffolds and Computational Fluid Dynamics that show the value of computer simulations in determining the influence of the geometrical scaffold parameter porosity, pore size and shape on the permeability of scaffolds, magnitude of velocity, drop pressure, shear stress distribution and level and the proper design of the geometry of the scaffold. This creates a need for more advanced studies that include aspects of dynamic conditions of a micro fluid passing through the scaffold were characterized for tissue engineering applications and differentiation of tissues within scaffolds.
Abstract: Understanding how airborne pathogens are
transported through hospital wards is essential for determining the
infection risk to patients and healthcare workers. This study utilizes
Computational Fluid Dynamics (CFD) simulations to explore
possible pathogen transport within a six-bed partitioned Nightingalestyle
hospital ward.
Grid independence of a ward model was addressed using the Grid
Convergence Index (GCI) from solutions obtained using three fullystructured
grids. Pathogens were simulated using source terms in
conjunction with a scalar transport equation and a RANS turbulence
model. Errors were found to be less than 4% in the calculation of air
velocities but an average of 13% was seen in the scalar field.
A parametric study of variations in the pathogen release point
illustrated that its distribution is strongly influenced by the local
velocity field and the degree of air mixing present.
Abstract: Many methods exist for either measuring or estimating
evaporation from free water surfaces. Evaporation pans provide one
of the simplest, inexpensive, and most widely used methods of
estimating evaporative losses. In this study, the rate of evaporation
starting from a water surface was calculated by modeling with
application to dams in wet, arid and semi arid areas in Algeria.
We calculate the evaporation rate from the pan using the energy
budget equation, which offers the advantage of an ease of use, but
our results do not agree completely with the measurements taken by
the National Agency of areas carried out using dams located in areas
of different climates. For that, we develop a mathematical model to
simulate evaporation. This simulation uses an energy budget on the
level of a vat of measurement and a Computational Fluid Dynamics
(Fluent). Our calculation of evaporation rate is compared then by the
two methods and with the measures of areas in situ.
Abstract: Shape optimization of the airfoil with high aspect ratio
of long endurance unmanned aerial vehicle (UAV) is performed by the
multi-objective optimization technology coupled with computational
fluid dynamics (CFD). For predicting the aerodynamic characteristics
around the airfoil the high-fidelity Navier-Stokes solver is employed
and SMOGA (Simple Multi-Objective Genetic Algorithm), which is
developed by authors, is used for solving the multi-objective
optimization problem. To obtain the optimal solutions of the design
variable (i.e., sectional airfoil profile, wing taper ratio and sweep) for
high performance of UAVs, both the lift and lift-to-drag ratio are
maximized whereas the pitching moment should be minimized,
simultaneously. It is found that the lift force and lift-to-drag ratio are
linearly dependent and a unique and dominant solution are existed.
However, a trade-off phenomenon is observed between the lift-to-drag
ratio and pitching moment. As the result of optimization, sixty-five
(65) non-dominated Pareto individuals at the cutting edge of design
spaces that is decided by airfoil shapes can be obtained.
Abstract: One promising way to achieve low temperature
combustion regime is the use of a large amount of cooled EGR. In
this paper, the effect of injection timing on low temperature
combustion process and emissions were investigated via three
dimensional computational fluid dynamics (CFD) procedures in a DI
diesel engine using high EGR rates. The results show when
increasing EGR from low levels to levels corresponding to reduced
temperature combustion, soot emission after first increasing, is
decreased beyond 40% EGR and get the lowest value at 58% EGR
rate. Soot and NOx emissions are simultaneously decreased at
advanced injection timing before 20.5 ºCA BTDC in conjunction
with 58% cooled EGR rate in compared to baseline case.
Abstract: Numerical integration of initial boundary problem for advection equation in 3 ℜ is considered. The method used is
conditionally stable semi-Lagrangian advection scheme with high order interpolation on unstructured mesh. In order to increase time step integration the BFECC method with limiter TVD correction is used. The method is adopted on parallel graphic processor unit environment using NVIDIA CUDA and applied in Navier-Stokes solver. It is shown that the calculation on NVIDIA GeForce 8800
GPU is 184 times faster than on one processor AMDX2 4800+ CPU. The method is extended to the incompressible fluid dynamics solver. Flow over a Cylinder for 3D case is compared to the experimental data.
Abstract: Supersonic open and closed cavity flows are investigated experimentally and computationally. Free stream Mach number of two is set. Schlieren imaging is used to visualise the flow behaviour showing stark differences between open and closed. Computational Fluid Dynamics (CFD) is used to simulate open cavity of flow with aspect ratio of 4. A rear wall treatment is implemented in order to pursue a simple passive control approach. Good qualitative agreement is achieved between the experimental flow visualisation and the CFD in terms of the expansion-shock waves system. The cavity oscillations are shown to be dominated by the first and third Rossister modes combining to high fluctuations of non-linear nature above the cavity rear edge. A simple rear wall treatment in terms of a hole shows mixed effect on the flow oscillations, RMS contours, and time history density fluctuations are given and analysed.
Abstract: The purpose of this paper is applied Taguchi method on the optimization for PEMFC performance, and a representative Computational Fluid Dynamics (CFD) model is selectively performed for statistical analysis. The studied factors in this paper are pressure of fuel cell, operating temperature, the relative humidity of anode and cathode, porosity of gas diffusion electrode (GDE) and conductivity of GDE. The optimal combination for maximum power density is gained by using a three-level statistical method. The results confirmed that the robustness of the optimum design parameters influencing the performance of fuel cell are founded by pressure of fuel cell, 3atm; operating temperature, 353K; the relative humidity of anode, 50%; conductivity of GDE, 1000 S/m, but the relative humidity of cathode and porosity of GDE are pooled as error due to a small sum of squares. The present simulation results give designers the ideas ratify the effectiveness of the proposed robust design methodology for the performance of fuel cell.
Abstract: The simulation of external aerodynamics is one of the most challenging and important automotive CFD applications. With the rapid developments of digital computers, CFD is used as a practical tool in modern fluid dynamics research. It integrates fluid mechanics disciplines, mathematics and computer science. In this study, two different types of simulations were made, one for the flow around a simplified high speed passenger car with a rear-spoiler and the other for the flow without a rear-spoiler. The standard k-ε model is selected to numerically simulate the external flow field of the simplified Camry model with or without a rear-spoiler. Through an analysis of the simulation results, a new rear spoiler is designed and it shows a mild reduction of the vehicle aerodynamics drag. This leads to less vehicle fuel consumption on the road.
Abstract: Cardiovascular disease mostly in the form of atherosclerosis is responsible for 30% of all world deaths amounting to 17 million people per year. Atherosclerosis is due to the formation of plaque. The fatty plaque may be at risk of rupture, leading typically to stroke and heart attack. The plaque is usually associated with a high degree of lumen reduction, called a stenosis. The initiation and progression of the disease is strongly linked to the hemodynamic environment near the vessel wall. The aim of this study is to validate the flow of blood mimic through an arterial stenosis model with computational fluid dynamics (CFD) package. In experiment, an axisymmetric model constructed consists of contraction and expansion region that follow a mathematical form of cosine function. A 30% diameter reduction was used in this study. Particle image velocimetry (PIV) was used to characterize the flow. The fluid consists of rigid spherical particles suspended in waterglycerol- NaCl mixture. The particles with 20 μm diameter were selected to follow the flow of fluid. The flow at Re=155, 270 and 390 were investigated. The experimental result is compared with FLUENT simulated flow that account for viscous laminar flow model. The results suggest that laminar flow model was sufficient to predict flow velocity at the inlet but the velocity at stenosis throat at Re =390 was overestimated. Hence, a transition to turbulent regime might have been developed at throat region as the flow rate increases.
Abstract: In this paper, the feasibility study of using a hybrid
system of ground heat exchangers (GHE) and direct evaporative
cooling system in arid weather condition has been performed. The
model is applied for Yazd and Kerman, two cities with arid weather
condition in Iran. The system composed of three sections: Ground-
Coupled-Circuit (GCC), Direct Evaporative Cooler (DEC) and
Cooling Coil Unite (CCU). The GCC provides the necessary precooling
for DEC. The GCC includes four vertical GHE which are
designed in series configuration. Simulation results show that
hybridization of GCC and DEC could provide comfort condition
whereas DEC alone did not. Based on the results the cooling
effectiveness of a hybrid system is more than unity. Thus, this novel
hybrid system could decrease the air temperature below the ambient
wet-bulb temperature. This environmentally clean and energy
efficient system can be considered as an alternative to the mechanical
vapor compression systems.
Abstract: Three dimensional simulations in tube in tube heat
exchangers are investigated numerically in this study. In these
simulations forced convective heat transfer and laminar flow of
single-phase water are considered. In order to measure heat transfer
parameters in these heat exchangers, FLUENT CFD Solver is used in
this numerical method. For the purpose of creating geometry and
exert boundary and initial conditions in the present model, finite
volume method in Computational Fluid Dynamics is used in this
study. In the present study, at each Z-location, variation of local
temperatures, heat flux and Nusselt number at the whole tube is
investigated in detail. Thereafter, averaged computational Nusselt
number in this model is calculated. In addition, conceivable pressure
drops have been obtained at each Z-location in this model. Then,
pressure drop values in the present model are explored. Finally, all
the numerical results for this kind of heat exchanger will be discussed
precisely.