Abstract: The oil and gas industry has moved towards Load and
Resistance Factor Design through API RP2A - LRFD and the
recently published international standard, ISO-19902, for design of
fixed steel offshore structures. The ISO 19902 is intended to provide
a harmonized design practice that offers a balanced structural fitness
for the purpose, economy and safety. As part of an ongoing work, the
reliability analysis of tubular joints of the jacket structure has been
carried out to calibrate the load and resistance factors for the design
of offshore platforms in Malaysia, as proposed in the ISO.
Probabilistic models have been established for the load effects (wave,
wind and current) and the tubular joints strengths. In this study the
First Order Reliability Method (FORM), coded in MATLAB
Software has been employed to evaluate the reliability index of the
typical joints, designed using API RP2A - WSD and ISO 19902.
Abstract: In this study, a software has been developed to predict
the optimum conditions for drying of cotton based yarn bobbins in a
hot air dryer. For this purpose, firstly, a suitable drying model has
been specified using experimental drying behavior for different
values of drying parameters. Drying parameters in the experiments
were drying temperature, drying pressure, and volumetric flow rate of
drying air. After obtaining a suitable drying model, additional curve
fittings have been performed to obtain equations for drying time and
energy consumption taking into account the effects of drying
parameters. Then, a software has been developed using Visual Basic
programming language to predict the optimum drying conditions for
drying time and energy consumption.
Abstract: In gas lifted oil fields, the lift gas should be distributed optimally among the wells which share gas from a common source to maximize total oil production. One of the objectives of the paper is to show that a linear MPC consisting of a control objective and an economic objective can be used both as an optimizer and a controller for gas lifted systems. The MPC is based on linearized model of the oil field developed from first principles modeling. Simulation results show that the total oil production is increased by 3.4%. Difficulties in accurately measuring the bottom hole pressure using sensors in harsh operating conditions can be resolved by using an Unscented Kalman Filter (UKF) for estimation. In oil fields where input disturbance (total supply of gas) is not measured, UKF can also be used for disturbance estimation. Increased total oil production due to optimization leads to increased profit.
Abstract: In this paper, a modified CCCII is presented. We have used a current mirror with low supply voltage. This circuit is operated at low supply voltage of ±1V. Tspice simulations for TSMC 0.18μm CMOS Technology has shown that the current and voltage bandwidth are respectively 3.34GHz and 4.37GHz, and parasitic resistance at port X has a value of 169.320 for a control current of 120μA. In order to realize this circuit, we have implemented in this first step a universal current mode filter where the frequency can reach the 134.58MHz. In the second step, we have implemented two simulated inductors: one floating and the other grounded. These two inductors are operated in high frequency and variable depending on bias current I0. Finally, we have used the two last inductors respectively to implement two sinusoidal oscillators domains of frequencies respectively: [470MHz, 692MHz], and [358MHz, 572MHz] for bias currents I0 [80μA, 350μA].
Abstract: In this paper we present a generic approach for the problem of the blind estimation of the parameters of linear and convolutional error correcting codes. In a non-cooperative context, an adversary has only access to the noised transmission he has intercepted. The intercepter has no knowledge about the parameters used by the legal users. So, before having acess to the information he has first to blindly estimate the parameters of the error correcting code of the communication. The presented approach has the main advantage that the problem of reconstruction of such codes can be expressed in a very simple way. This allows us to evaluate theorical bounds on the complexity of the reconstruction process but also bounds on the estimation rate. We show that some classical reconstruction techniques are optimal and also explain why some of them have theorical complexities greater than these experimentally observed.
Abstract: In the last few years, three multivariate spectral
analysis techniques namely, Principal Component Analysis (PCA),
Independent Component Analysis (ICA) and Non-negative Matrix
Factorization (NMF) have emerged as effective tools for oscillation
detection and isolation. While the first method is used in determining
the number of oscillatory sources, the latter two methods
are used to identify source signatures by formulating the detection
problem as a source identification problem in the spectral domain.
In this paper, we present a critical drawback of the underlying linear
(mixing) model which strongly limits the ability of the associated
source separation methods to determine the number of sources
and/or identify the physical source signatures. It is shown that the
assumed mixing model is only valid if each unit of the process gives
equal weighting (all-pass filter) to all oscillatory components in its
inputs. This is in contrast to the fact that each unit, in general, acts
as a filter with non-uniform frequency response. Thus, the model
can only facilitate correct identification of a source with a single
frequency component, which is again unrealistic. To overcome
this deficiency, an iterative post-processing algorithm that correctly
identifies the physical source(s) is developed. An additional issue
with the existing methods is that they lack a procedure to pre-screen
non-oscillatory/noisy measurements which obscure the identification
of oscillatory sources. In this regard, a pre-screening procedure
is prescribed based on the notion of sparseness index to eliminate
the noisy and non-oscillatory measurements from the data set used
for analysis.
Abstract: Knowledge of patterns of genetic diversity enhances
the efficiency of germplasm conservation and improvement. In this
study 96 Iranian landraces of Triticum turgidum originating from
different geographical areas of Iran, along with 18 durum cultivars
from ten countries were evaluated for variation in morphological and
high molecular weight glutenin subunit (HMW-GS) composition.
The first two principal components clearly separated the Iranian
landraces from cultivars. Three alleles were present at the Glu-A1
locus and 11 alleles at Glu-B1. In both cultivars and landraces of
durum wheat, the null allele (Glu-A1c) was observed more
frequently than the Glu-A1a and Glu-A1b alleles. Two alleles,
namely Glu-B1a (subunit 7) and Glu-B1e (subunit 20) represented
the more frequent alleles at Glu-B1 locus. The results showed that
the evaluated Iranian landraces formed an interesting source of
favourable glutenin subunits that might be very desirable in breeding
activities for improving pasta-making quality.
Abstract: Selection of a project among a set of possible
alternatives is a difficult task that the decision maker (DM) has to
face. In this paper, by using a fuzzy TOPSIS technique we propose a
new method for a project selection problem. After reviewing four
common methods of comparing investment alternatives (net present
value, rate of return, benefit cost analysis and payback period) we
use them as criteria in a TOPSIS technique. First we calculate the
weight of each criterion by a pairwise comparison and then we utilize
the improved TOPSIS assessment for the project selection.
Abstract: Fast delay estimation methods, as opposed to
simulation techniques, are needed for incremental performance
driven layout synthesis. On-chip inductive effects are becoming
predominant in deep submicron interconnects due to increasing clock
speed and circuit complexity. Inductance causes noise in signal
waveforms, which can adversely affect the performance of the circuit
and signal integrity. Several approaches have been put forward which
consider the inductance for on-chip interconnect modelling. But for
even much higher frequency, of the order of few GHz, the shunt
dielectric lossy component has become comparable to that of other
electrical parameters for high speed VLSI design. In order to cope up
with this effect, on-chip interconnect has to be modelled as
distributed RLCG line. Elmore delay based methods, although
efficient, cannot accurately estimate the delay for RLCG interconnect
line. In this paper, an accurate analytical delay model has been
derived, based on first and second moments of RLCG
interconnection lines. The proposed model considers both the effect
of inductance and conductance matrices. We have performed the
simulation in 0.18μm technology node and an error of as low as less
as 5% has been achieved with the proposed model when compared to
SPICE. The importance of the conductance matrices in interconnect
modelling has also been discussed and it is shown that if G is
neglected for interconnect line modelling, then it will result an delay
error of as high as 6% when compared to SPICE.