Abstract: Cellular networks provide voice and data services to the users with mobility. To deliver services to the mobile users, the cellular network is capable of tracking the locations of the users, and allowing user movement during the conversations. These capabilities are achieved by the location management. Location management in mobile communication systems is concerned with those network functions necessary to allow the users to be reached wherever they are in the network coverage area. In a cellular network, a service coverage area is divided into smaller areas of hexagonal shape, referred to as cells. The cellular concept was introduced to reuse the radio frequency. Continued expansion of cellular networks, coupled with an increasingly restricted mobile spectrum, has established the reduction of communication overhead as a highly important issue. Much of this traffic is used in determining the precise location of individual users when relaying calls, with the field of location management aiming to reduce this overhead through prediction of user location. This paper describes and compares various location management schemes in the cellular networks.
Abstract: A new technique to quantify the differential mode
delay (DMD) in multimode fiber (MMF) is been presented. The
technique measures DMD based on angular launch and
measurements of the difference in modal delay using variable
apertures at the fiber face. The result of the angular spatial filtering
revealed less excitation of higher order modes when the laser beam is
filtered at higher angles. This result would indicate that DMD
profiles would experience a data pattern dependency.
Abstract: An analytical solution for dispersion of a solute in the
peristaltic motion of a couple stress fluid in the presence of magnetic
field with both homogeneous and heterogeneous chemical reactions is
presented. The average effective dispersion coefficient has been found
using Taylor-s limiting condition and long wavelength approximation.
The effects of various relevant parameters on the average effective
coefficient of dispersion have been studied. The average effective
dispersion coefficient tends to decrease with magnetic field parameter,
homogeneous chemical reaction rate parameter and amplitude ratio
but tends to increase with heterogeneous chemical reaction rate
parameter.
Abstract: Recent progress in calculation of the one-loop selfenergy
of the electron bound in the Coulomb field is summarized.
The relativistic multipole expansion is introduced. This expansion
is based on a single assumption: except for the part of the time
component of the electron four-momentum corresponding to the
electron rest mass, the exchange of four-momentum between the
virtual electron and photon can be treated perturbatively. For non Sstates
and normalized difference n3En −E1 of the S-states this
itself yields very accurate results after taking the method to the third
order. For the ground state the perturbation treatment of the electron
virtual states with very high three-momentum is to be avoided. For
these states one can always rearrange the pertinent expression in such
a way that free-particle approximation is allowed. Combination of
the relativistic multipole expansion and free-particle approximation
yields very accurate result after taking the method to the ninth order.
These results are in very good agreement with the previous results
obtained by the partial wave expansion and definitely exclude the
possibility that the uncertainity in determination of the proton radius
comes from the uncertainity in the calculation of the one-loop selfenergy.
Abstract: It is necessary to incorporate technological advances
achieved in the field of engineering into dentistry in order to enhance
the process of diagnosis, treatment planning and enable the doctors to
render better treatment to their patients. To achieve this ultimate goal
long distance collaborations are often necessary. This paper discusses
the various collaborative tools and their applications to solve a few
burning problems confronted by the dentists. Customization is often
the solution to most of the problems. But rapid designing,
development and cost effective manufacturing is a difficult task to
achieve. This problem can be solved using the technique of digital
manufacturing. Cases from 6 major branches of dentistry have been
discussed and possible solutions with the help of state of art
technology using rapid digital manufacturing have been proposed in
the present paper. The paper also entails the usage of existing tools in
collaborative and digital manufacturing area.
Abstract: The purpose of this paper is to describe the process of
setting up a learning community within an elementary school in
Ontario, Canada. The description is provided through reflection and
examination of field notes taken during the yearlong training and
implementation process. Specifically the impact of teachers- capacity
on the creation of a learning community was of interest. This paper is
intended to inform and add to the debate around the tensions that
exist in implementing a bottom-up professional development model
like the learning community in a top-down organizational structure.
My reflections of the process illustrate that implementation of the
learning community professional development model may be
difficult and yet transformative in the professional lives of the
teachers, students, and administration involved in the change process.
I conclude by suggesting the need for a new model of professional
development that requires a transformative shift in power dynamics
and a shift in the view of what constitutes effective professional
learning.
Abstract: This paper presents a systematic procedure for modelling and simulation of a power system installed with a power system stabilizer (PSS) and a flexible ac transmission system (FACTS)-based controller. For the design purpose, the model of example power system which is a single-machine infinite-bus power system installed with the proposed controllers is developed in MATLAB/SIMULINK. In the developed model synchronous generator is represented by model 1.1. which includes both the generator main field winding and the damper winding in q-axis so as to evaluate the impact of PSS and FACTS-based controller on power system stability. The model can be can be used for teaching the power system stability phenomena, and also for research works especially to develop generator controllers using advanced technologies. Further, to avoid adverse interactions, PSS and FACTS-based controller are simultaneously designed employing genetic algorithm (GA). The non-linear simulation results are presented for the example power system under various disturbance conditions to validate the effectiveness of the proposed modelling and simultaneous design approach.
Abstract: The amount of the information being churned out by the field of biology has jumped manifold and now requires the extensive use of computer techniques for the management of this information. The predominance of biological information such as protein sequence similarity in the biological information sea is key information for detecting protein evolutionary relationship. Protein sequence similarity typically implies homology, which in turn may imply structural and functional similarities. In this work, we propose, a learning method for detecting remote protein homology. The proposed method uses a transformation that converts protein sequence into fixed-dimensional representative feature vectors. Each feature vector records the sensitivity of a protein sequence to a set of amino acids substrings generated from the protein sequences of interest. These features are then used in conjunction with support vector machines for the detection of the protein remote homology. The proposed method is tested and evaluated on two different benchmark protein datasets and it-s able to deliver improvements over most of the existing homology detection methods.
Abstract: Empirical force fields and density functional theory
(DFT) was used to study the binding energies and structures of
methylamine on the surface of activated carbons (ACs). This is a first
step in studying the adsorption of alkyl amines on the surface of
functionalized ACs. The force fields used were Dreiding (DFF),
Universal (UFF) and Compass (CFF) models. The generalized
gradient approximation with Perdew Wang 91 (PW91) functional
was used for DFT calculations. In addition to obtaining the aminecarboxylic
acid adsorption energies, the results were used to establish
reliability of the empirical models for these systems. CFF predicted a
binding energy of -9.227 (kcal/mol) which agreed with PW91 at -
13.17 (kcal/mol), compared to DFF 0 (kcal/mol) and UFF -0.72
(kcal/mol). However, the CFF binding energies for the amine to ester
and ketone disagreed with PW91 results. The structures obtained
from all models agreed with PW91 results.
Abstract: The present work deals with the calculation of
transport properties of Hg0.8Cd0.2Te (MCT) semiconductor in
degenerate case. Due to their energy-band structure, this material
becomes degenerate at moderate doping densities, which are around
1015 cm-3, so that the usual Maxwell-Boltzmann approximation is
inaccurate in the determination of transport parameters. This problem
is faced by using Fermi-Dirac (F-D) statistics, and the non-parabolic
behavior of the bands may be approximated by the Kane model. The
Monte Carlo (MC) simulation is used here to determinate transport
parameters: drift velocity, mean energy and drift mobility versus
electric field and the doped densities. The obtained results are in
good agreement with those extracted from literature.
Abstract: The theoretical investigation is carried out to describe
the effect of increase of pressure waves amplitude in clean and bubbly liquid. The goal of the work is to capture the regime of multiple magnification of acoustic and shock waves in the liquid,
which enables to get appropriate conditions to enlarge collapses of
micro-bubbles. The influence of boundary conditions and frequency
of the governing acoustic field is studied for the case of the
cylindrical acoustic resonator. It has been observed the formation of
standing waves with large amplitude at resonant frequencies. The
interaction of the compression wave with gas and vapor bubbles is
investigated for the convergent channel. It is shown theoretically that
the chemical reactions, which occur inside gas bubbles, provide additional impulse to the wave, that affect strongly on the collapses
of the vapor bubbles
Abstract: Field experiment was conducted to investigate the combine use of animal manure and inorganic fertilizer on growth and yield performance of vegetable cowpea. The experiment was laid out in a Randomized Complete Block Design (RCBD) with seven treatments. Poultry manure, cattle manure and goat manure were evaluated with recommended level of inorganic fertilizer for vegetable cowpea. The highest crop yield was obtained by the application of poultry manure combined with the recommended level of inorganic fertilizer. The lowest yield was obtained by the application of goat manure only. In addition, the results revealed that the goat manure and cattle manure were inferior to poultry manure as a source of organic manure for vegetable cowpea cultivation. The animal manure combine with chemical fertilizer gave a higher yield when compared to the sole application of animal manure. The soil analysis showed that the nitrogen content and phosphorus content of poultry manure treated plots were higher than other treatments tested. But potassium content was higher in goat manure treated plots. The results further revealed that the poultry manure has a beneficial effect on crop growth and yield compared with other treatments. Therefore, the combined use of poultry manure with inorganic fertilizer application has been recognized as the most suitable way of ensuring high crop yield.
Abstract: The link between urban planning and design principles and the built environment of an urban renewal area is of interest to the field of urban studies. During the past decade, there has also been increasing interest in urban planning and design; this interest is motivated by the possibility that design policies associated with the built environment can be used to control, manage, and shape individual activity and behavior. However, direct assessments and design techniques of the links between how urban planning design policies influence individuals are still rare in the field. Recent research efforts in urban design have focused on the idea that land use and design policies can be used to increase the quality of design projects for an urban renewal area-s built environment. The development of appropriate design techniques for the built environment is an essential element of this research. Quality function deployment (QFD) is a powerful tool for improving alternative urban design and quality for urban renewal areas, and for procuring a citizen-driven quality system. In this research, we propose an integrated framework based on QFD and an Analytic Network Process (ANP) approach to determine the Alternative Technical Requirements (ATRs) to be considered in designing an urban renewal planning and design alternative. We also identify the research designs and methodologies that can be used to evaluate the performance of urban built environment projects. An application in an urban renewal built environment planning and design project evaluation is presented to illustrate the proposed framework.
Abstract: We report here structural, mechanical and I-V
characteristics of Zn1-xMxO ceramic samples with various x and M.
It is found that the considered dopants does not influence the wellknown
peaks related to wurtzite structure of ZnO ceramics, while the
shape and size of grains are clearly affected. Average crystalline
diameters, deduced from XRD are between 42 nm and 54 nm, which
are 70 times lower than those obtained from SEM micrographs.
Interestingly, the potential barrier could be formed by adding Cu up
to 0.20, and it is completely deformed by 0.025 Ni additions. The
breakdown field could be enhanced up to 4138 V/cm by 0.025 Cu
additions, followed by a decrease with further increase of Cu . On
the other hand a gradual decrease in VHN is reported for both
dopants and their values are higher in Ni samples as compared to Cu
samples. The electrical conductivity is generally improved by Ni,
while addition of Cu improved it only in the over doped region (≥
0.10). These results are discussed in terms of the difference of
valency and ferromagnetic ordering for both dopants as compared to
undoped sample.
Abstract: In this paper, the thermo-electro-structural coupledfield
in a cracked metal plate is studied using the finite element
analysis. From the computational results, the compressive stresses
reveal near the crack tip. This conclusion agrees with the past
reference. Furthermore, the compressive condition can retard and stop
the crack growth during the Joule heating process.
Abstract: A wireless power transfer system can attribute to the
fields in robot, aviation and space in which lightening the weight of
device and improving the movement play an important role. A
wireless power transfer system was investigated to overcome the
inconvenience of using power cable. Especially a wireless power
transfer technology is important element for mobile robots. We
proposed the wireless power transfer system of the half-bridge
resonant converter with the frequency tracking and optimized
power transfer control unit. And the possibility of the application
and development system was verified through the experiment with
LED loads.
Abstract: Hydraulic conductivity is one parameter important for predicting the movement of water and contaminants dissolved in the water through the soil. The hydraulic conductivity is measured on soil samples in the lab and sometimes tests carried out in the field. The hydraulic conductivity has been related to soil particle diameter by a number of investigators. In this study, 25 set of soil samples with sand texture. The results show approximately success in predicting hydraulic conductivity from particle diameters data. The following relationship obtained from multiple linear regressions on data (R2 = 0.52): Where d10, d50 and d60, are the soil particle diameter (mm) that 10%, 50% and 60% of all soil particles are finer (smaller) by weight and Ks, saturated hydraulic conductivity is expressed in m/day. The results of regression analysis showed that d10 play a more significant role with respect to Ks, saturated hydraulic conductivity (m/day), and has been named as the effective parameter in Ks calculation.
Abstract: Via a large scale cross-sectional study among Japanese white color workers, the authors aimed to elucidate: (1) the distributions of Sense of Coherence (SOC), which reflect stress coping abilities, (2) the distributions of Life experience; (3) and the association between SOC and Life experience. Anonymous self-administered questionnaires were sent to 15,891 in 2001 and 21,922 in 2011 employees at educational and research institutions in Tsukuba Research Park City. A total of 5,868 (36.9%) and 9,528 (43.5%) respectively workers completed and returned the questionnaire; 5,715 and 9,515 respectively workers without missing data were analyzed. SOC scale scores differed by gender, age, and other demographic features in both study years. Among the life experiences, workers who have got over parenting or management position were higher SOC scale scores adjusted by gender and age. The life experiences that workers have got over could develop their stronger SOC in their life course.
Abstract: Successful intelligence (SI) is the integrated set of the
ability needed to attain success in life, within individual-s sociocultural
context. People are successfully intelligent by recognizing
their strengths and weaknesses. They will find ways to strengthen
their weakness and maintain their strength or even improve it. SI
people can shape, select, and adapt to the environments by using
balance of higher-ordered thinking abilities including; critical,
creative, and applicative. Aims: The purposes of this study were to;
1) develop curriculum that promotes SI for nursing students, and 2)
study the effectiveness of the curriculum development. Method:
Research and Development was a method used for this study. The
design was divided into two phases; 1) the curriculum development
which composed of three steps (needs assessment, curriculum
development and curriculum field trail), and 2) the curriculum
implementation. In this phase, a pre-experimental research design
(one group pretest-posttest design) was conducted. The sample
composed of 49 sophomore nursing students of Boromarajonani
College of Nursing, Surin, Thailand who enrolled in Nursing care of
Health problem course I in 2011 academic year. Data were carefully
collected using 4 instruments; 1) Modified essay questions test
(MEQ) 2) Nursing Care Plan evaluation form 3) Group processing
observation form (α = 0.74) and 4) Satisfied evaluation form of
learning (α = 0.82). Data were analyzed using descriptive statistics
and content analysis. Results: The results revealed that the sample
had post-test average score of SI higher than pre-test average score
(mean difference was 5.03, S.D. = 2.84). Fifty seven percentages of
the sample passed the MEQ posttest at the criteria of 60 percentages.
Students demonstrated the strategies of how to develop nursing care
plan. Overall, students- satisfaction on teaching performance was at
high level (mean = 4.35, S.D. = 0.46). Conclusion: This curriculum
can promote the attribute of characteristic of SI person and was
highly required to be continued.
Abstract: Simulations of magnetic microstructure in elliptical
Permalloy elements used for controlled motion of magnetic particles
are discussed. The saturating field of the elliptical elements was
studied with respect to lateral dimensions for one-vortex, cross-tie,
diamond and double-diamond states as initial zero-field domain
configurations. With aspect ratio of 1:3 the short axis was varied
from 125 nm to 1000 nm, whereas the thickness was kept constant at
50 nm.