Abstract: Snow cover is an important phenomenon in
hydrology, hence modeling the snow accumulation and melting is an
important issue in places where snowmelt significantly contributes to
runoff and has significant effect on water balance. The physics-based
models are invariably distributed, with the basin disaggregated into
zones or grid cells. Satellites images provide valuable data to verify
the accuracy of spatially distributed model outputs. In this study a
spatially distributed physically based model (WetSpa) was applied to
predict snow cover and melting in the Latyan dam watershed in Iran.
Snowmelt is simulated based on an energy balance approach. The
model is applied and calibrated with one year of observed daily
precipitation, air temperature, windspeed, and daily potential
evaporation. The predicted snow-covered area is compared with
remotely sensed images (MODIS). The results show that simulated
snow cover area SCA has a good agreement with satellite image
snow cover area SCA from MODIS images. The model performance
is also tested by statistical and graphical comparison of simulated and
measured discharges entering the Latyan dam reservoir.
Abstract: An on-line condition monitoring method for transmission line is proposed using electrical circuit theory and IT technology in this paper. It is reasonable that the circuit parameters such as resistance (R), inductance (L), conductance (g) and capacitance (C) of a transmission line expose the electrical conditions and physical state of the line. Those parameters can be calculated from the linear equation composed of voltages and currents measured by synchro-phasor measurement technique at both end of the line. A set of linear voltage drop equations containing four terminal constants (A, B ,C ,D ) are mathematical models of the transmission line circuits. At least two sets of those linear equations are established from different operation condition of the line, they may mathematically yield those circuit parameters of the line. The conditions of line connectivity including state of connecting parts or contacting parts of the switching device may be monitored by resistance variations during operation. The insulation conditions of the line can be monitored by conductance (g) and capacitance(C) measurements. Together with other condition monitoring devices such as partial discharge, sensors and visual sensing device etc.,they may give useful information to monitor out any incipient symptoms of faults. The prototype of hardware system has been developed and tested through laboratory level simulated transmission lines. The test has shown enough evident to put the proposed method to practical uses.
Abstract: Direct conversion of methane to methanol by partial oxidation in a thermal reactor has a poor yield of about 2% which is less than the expected economical yield of about 10%. Conventional thermal catalytic reactors have been proposed to be superseded by plasma reactors as a promising approach, due to strength of the electrical energy which can break C-H bonds of methane. Among the plasma techniques, non-thermal dielectric barrier discharge (DBD) plasma chemical process is one of the most future promising technologies in synthesizing methanol. The purpose of this paper is presenting a brief review of CH4 oxidation with O2 in DBD plasma reactors based on the recent investigations. For this reason, the effect of various parameters of reactor configuration, feed ratio, applied voltage, residence time (gas flow rate), type of applied catalyst, pressure and reactor wall temperature on methane conversion and methanol selectivity are discussed.
Abstract: In this paper, a one-dimensional numerical approach is
used to study the effect of applying electrohydrodynamics on the
temperature and species mass fraction profiles along the microcombustor.
Premixed mixture is H2-Air with a multi-step chemistry
(9 species and 19 reactions). In the micro-scale combustion because
of the increasing ratio of area-to-volume, thermal and radical
quenching mechanisms are important. Also, there is a significant heat
loss from the combustor walls. By inserting a number of electrodes
into micro-combustor and applying high voltage to them corona
discharge occurs. This leads in moving of induced ions toward
natural molecules and colliding with them. So this phenomenon
causes the movement of the molecules and reattaches the flow to the
walls. It increases the velocity near the walls that reduces the wall
boundary layer. Consequently, applying electrohydrodynamics
mechanism can enhance the temperature profile in the microcombustor.
Ultimately, it prevents the flame quenching in microcombustor.
Abstract: Hexavalent chromium is highly toxic to most living organisms and a known human carcinogen by the inhalation route of exposure. Therefore, treatment of Cr(VI) contaminated wastewater is essential before their discharge to the natural water bodies. Cr(VI) reduction to Cr(III) can be beneficial because a more mobile and more toxic chromium species is converted to a less mobile and less toxic form. Zero-valence-state metals, such as scrap iron, can serve as electron donors for reducing Cr(VI) to Cr(III). The influence of pH on scrap iron capacity to reduce Cr(VI) was investigated in this study. Maximum reduction capacity of scrap iron was observed at the beginning of the column experiments; the lower the pH, the greater the experiment duration with maximum scrap iron reduction capacity. The experimental results showed that highest maximum reduction capacity of scrap iron was 12.5 mg Cr(VI)/g scrap iron, at pH 2.0, and decreased with increasing pH up to 1.9 mg Cr(VI)/g scrap iron at pH = 7.3.
Abstract: The performance and the plasma created by a pulsed
magnetoplasmadynamic thruster for small satellite application is
studied to understand better the ablation and plasma propagation
processes occurring during the short-time discharge. The results can
be applied to improve the quality of the thruster in terms of efficiency,
and to tune the propulsion system to the needs required by the satellite
mission. Therefore, plasma measurements with a high-speed camera
and induction probes, and performance measurements of mass bit
and impulse bit were conducted. Values for current sheet propagation
speed, mean exhaust velocity and thrust efficiency were derived from
these experimental data. A maximum in current sheet propagation
was found by the high-speed camera measurements for a medium
energy input and confirmed by the induction probes. A quasilinear
tendency between the mass bit and the energy input, the current
action integral respectively, was found, as well as a linear tendency
between the created impulse and the discharge energy. The highest
mean exhaust velocity and thrust efficiency was found for the highest
energy input.
Abstract: Petroleum refineries discharged large amount of
wastewater -during the refining process- that contains hazardous
constituents that is hard to degrade. Anaerobic treatment process is
well known as an efficient method to degrade high strength
wastewaters. Up-flow Anaerobic Sludge Blanker (UASB) is a
common process used for various wastewater treatments. Two UASB
reactors were set up and operated in parallel to evaluate the treatment
efficiency of petroleum refinery wastewater. In this study four
organic volumetric loading rates were applied (i.e. 0.58, 0.89, 1.21
and 2.34 kg/m3·d), two loads to each reactor. Each load was applied
for a period of 60 days for the reactor to acclimatize and reach steady
state, and then the second load applied. The chemical oxygen demand
(COD) removals were satisfactory with the removal efficiencies at the
loadings applied were 78, 82, 83 and 81 % respectively.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: Decentralized eco-sanitation system is a promising and sustainable mode comparing to the century-old centralized conventional sanitation system. The decentralized concept relies on an environmentally and economically sound management of water, nutrient and energy fluxes. Source-separation systems for urban waste management collect different solid waste and wastewater streams separately to facilitate the recovery of valuable resources from wastewater (energy, nutrients). A resource recovery centre constituted for 20,000 people will act as the functional unit for the treatment of urban waste of a high-density population community, like Singapore. The decentralized system includes urine treatment, faeces and food waste co-digestion, and horticultural waste and organic fraction of municipal solid waste treatment in composting plants. A design model is developed to estimate the input and output in terms of materials and energy. The inputs of urine (yellow water, YW) and faeces (brown water, BW) are calculated by considering the daily mean production of urine and faeces by humans and the water consumption of no-mix vacuum toilet (0.2 and 1 L flushing water for urine and faeces, respectively). The food waste (FW) production is estimated to be 150 g wet weight/person/day. The YW is collected and discharged by gravity into tank. It was found that two days are required for urine hydrolysis and struvite precipitation. The maximum nitrogen (N) and phosphorus (P) recovery are 150-266 kg/day and 20-70 kg/day, respectively. In contrast, BW and FW are mixed for co-digestion in a thermophilic acidification tank and later a decentralized/centralized methanogenic reactor is used for biogas production. It is determined that 6.16-15.67 m3/h methane is produced which is equivalent to 0.07-0.19 kWh/ca/day. The digestion residues are treated with horticultural waste and organic fraction of municipal waste in co-composting plants.
Abstract: The use of artificial neural network (ANN) modeling
for prediction and forecasting variables in water resources
engineering are being increasing rapidly. Infrastructural applications
of ANN in terms of selection of inputs, architecture of networks,
training algorithms, and selection of training parameters in different
types of neural networks used in water resources engineering have
been reported. ANN modeling conducted for water resources
engineering variables (river sediment and discharge) published in
high impact journals since 2002 to 2011 have been examined and
presented in this review. ANN is a vigorous technique to develop
immense relationship between the input and output variables, and
able to extract complex behavior between the water resources
variables such as river sediment and discharge. It can produce robust
prediction results for many of the water resources engineering
problems by appropriate learning from a set of examples. It is
important to have a good understanding of the input and output
variables from a statistical analysis of the data before network
modeling, which can facilitate to design an efficient network. An
appropriate training based ANN model is able to adopt the physical
understanding between the variables and may generate more effective
results than conventional prediction techniques.
Abstract: Droughts are complex, natural hazards that, to a
varying degree, affect some parts of the world every year. The range
of drought impacts is related to drought occurring in different stages
of the hydrological cycle and usually different types of droughts,
such as meteorological, agricultural, hydrological, and socioeconomical
are distinguished. Streamflow drought was analyzed by
the method of truncation level (at 70% level) on daily discharges
measured in 54 hydrometric stations in southwestern Iran. Frequency
analysis was carried out for annual maximum series (AMS) of
drought deficit volume and duration series. Some factors including
physiographic, climatic, geologic, and vegetation cover were studied
as influential factors in the regional analysis. According to the results
of factor analysis, six most effective factors were identified as area,
rainfall from December to February, the percent of area with
Normalized Difference Vegetation Index (NDVI)
Abstract: Reciprocating compressors are flexible to handle wide capacity and condition swings, offer a very efficient method of compressing almost any gas mixture in wide range of pressure, can generate high head independent of density, and have numerous applications and wide power ratings. These make them vital component in various units of industrial plants. In this paper optimum reciprocating compressor configuration regarding interstage pressures, low suction pressure, non-lubricated cylinder, speed of machine, capacity control system, compressor valve, lubrication system, piston rod coating, cylinder liner material, barring device, pressure drops, rod load, pin reversal, discharge temperature, cylinder coolant system, performance, flow, coupling, special tools, condition monitoring (including vibration, thermal and rod drop monitoring), commercial points, delivery and acoustic conditions are presented.
Abstract: In this paper an attempt has been made to correlate the usefulness of electrodes made through powder metallurgy (PM) in comparison with conventional copper electrode during electric discharge machining. Experimental results are presented on electric discharge machining of AISI D2 steel in kerosene with copper tungsten (30% Cu and 70% W) tool electrode made through powder metallurgy (PM) technique and Cu electrode. An L18 (21 37) orthogonal array of Taguchi methodology was used to identify the effect of process input factors (viz. current, duty cycle and flushing pressure) on the output factors {viz. material removal rate (MRR) and surface roughness (SR)}. It was found that CuW electrode (made through PM) gives high surface finish where as the Cu electrode is better for higher material removal rate.