Abstract: Modeling of Panel Zone (PZ) seismic behavior,
because of its role in overall ductility and lateral stiffness of steel
moment frames, has been considered a challenge for years. There are
some studies regarding the effects of different doubler plates
thicknesses and geometric properties of PZ on its seismic behavior.
However, there is not much investigation on the effects of number of
provided continuity plates in case of presence of one triangular
haunch, two triangular haunches and rectangular haunch (T shape
haunches) for exterior columns. In this research first detailed finite
element models of 12tested connection of SAC joint venture were
created and analyzed then obtained cyclic behavior backbone curves
of these models besides other FE models for similar tests were used
for neural network training. Then seismic behavior of these data is
categorized according to continuity plate-s arrangements and
differences in type of haunches. PZ with one-sided haunches have
little plastic rotation. As the number of continuity plates increases
due to presence of two triangular haunches (four continuity plate),
there will be no plastic rotation, in other words PZ behaves in its
elastic range. In the case of rectangular haunch, PZ show more plastic
rotation in comparison with one-sided triangular haunch and
especially double-sided triangular haunches. Moreover, the models
that will be presented in case of triangular one-sided and double-
sided haunches and rectangular haunches as a result of this study
seem to have a proper estimation of PZ seismic behavior.
Abstract: Linear stability of wake-shear layers in two-phase
shallow flows is analyzed in the present paper. Stability analysis is
based on two-dimensional shallow water equations. It is assumed that
the fluid contains uniformly distributed solid particles. No dynamic
interaction between the carrier fluid and particles is expected in the
initial moment. Linear stability curves are obtained for different
values of the particle loading parameter, the velocity ratio and the
velocity deficit. It is shown that the increase in the velocity ratio
destabilizes the flow. The particle loading parameter has a stabilizing
effect on the flow. The role of the velocity deficit is also
destabilizing: the increase of the velocity deficit leads to less stable
flow.
Abstract: To satisfy the need of outfield tests of star sensors, a
method is put forward to construct the reference attitude benchmark.
Firstly, its basic principle is introduced; Then, all the separate
conversion matrixes are deduced, which include: the conversion
matrix responsible for the transformation from the Earth Centered
Inertial frame i to the Earth-centered Earth-fixed frame w according to
the time of an atomic clock, the conversion matrix from frame w to the
geographic frame t, and the matrix from frame t to the platform frame
p, so the attitude matrix of the benchmark platform relative to the
frame i can be obtained using all the three matrixes as the
multiplicative factors; Next, the attitude matrix of the star sensor
relative to frame i is got when the mounting matrix from frame p to the
star sensor frame s is calibrated, and the reference attitude angles for
star sensor outfield tests can be calculated from the transformation
from frame i to frame s; Finally, the computer program is finished to
solve the reference attitudes, and the error curves are drawn about the
three axis attitude angles whose absolute maximum error is just 0.25ÔÇ│.
The analysis on each loop and the final simulating results manifest that
the method by precise timing to acquire the absolute reference attitude
is feasible for star sensor outfield tests.
Abstract: The effect of chemical treatment in CdCl2 and thermal
annealing in 400°C, on the defect structures of potentially useful
ZnS\CdS solar cell thin films deposited onto quartz substrate and
prepared by vacuum deposition method was studied using the
Thermoluminesence (TL) techniques. A series of electron and hole
traps are found in the various deposited samples studied. After
annealing, however, it was observed that the intensity and activation
energy of TL signal increases with loss of the low temperature
electron traps.
Abstract: In this paper we present an efficient method for inverting an ideal in the ideal class group of a Cab curve by extending the method which is presented in [3]. More precisely we introduce a useful generator for the inverse ideal as a K[X]-module.
Abstract: The exploration of this paper will focus on the Cshaped
transition curve. This curve is designed by using the concept
of circle to circle where one circle lies inside other. The degree of
smoothness employed is curvature continuity. The function used in
designing the C-curve is Bézier-like cubic function. This function has
a low degree, flexible for the interactive design of curves and
surfaces and has a shape parameter. The shape parameter is used to
control the C-shape curve. Once the C-shaped curve design is
completed, this curve will be applied to design spur gear tooth. After
the tooth design procedure is finished, the design will be analyzed by
using Finite Element Analysis (FEA). This analysis is used to find
out the applicability of the tooth design and the gear material that
chosen. In this research, Cast Iron 4.5 % Carbon, ASTM A-48 is
selected as a gear material.
Abstract: In this study, the effect of nanofluids on the pool film
boiling was experimentally investigated at saturated condition under
atmospheric pressure. For this purpose, four different water-based
nanofluids (Al2O3, SiO2, TiO2 and CuO) with 0.1% particle volume
fraction were prepared. To investigate the boiling heat transfer, a
cylindrical rod with high temperature was used. The rod heated up to
high temperatures was immersed into nanofluids. The center
temperature of rod during the cooling process was recorded by using
a K-type thermocouple. The quenching curves showed that the pool
boiling heat transfer was strongly dependent on the nanoparticle
materials. During the repetitive quenching tests, the cooling time
decreased and thus, the film boiling vanished. Consequently, the
primary reason of this was the change of the surface characteristics
due to the nanoparticles deposition on the rod-s surface.
Abstract: The purpose of this study is mainly to predict collision
frequency on the horizontal tangents combined with vertical curves
using artificial neural network methods. The proposed ANN models
are compared with existing regression models. First, the variables
that affect collision frequency were investigated. It was found that
only the annual average daily traffic, section length, access density,
the rate of vertical curvature, smaller curve radius before and after
the tangent were statistically significant according to related
combinations. Second, three statistical models (negative binomial,
zero inflated Poisson and zero inflated negative binomial) were
developed using the significant variables for three alignment
combinations. Third, ANN models are developed by applying the
same variables for each combination. The results clearly show that
the ANN models have the lowest mean square error value than those
of the statistical models. Similarly, the AIC values of the ANN
models are smaller to those of the regression models for all the
combinations. Consequently, the ANN models have better statistical
performances than statistical models for estimating collision
frequency. The ANN models presented in this paper are
recommended for evaluating the safety impacts 3D alignment
elements on horizontal tangents.
Abstract: Herein, the organic semiconductor methyl orange
(MO), is investigated for the first time for its electronic applications.
For this purpose, Al/MO/n-Si heterojunction is fabricated through
economical cheap and simple “drop casting” technique. The currentvoltage
(I-V) measurements of the device are made at room
temperature under dark conditions. The I-V characteristics of
Al/MO/n-Si junction exhibits asymmetrical and rectifying behavior
that confirms the formation of diode. The diode parameters such as
rectification ratio (RR), turn on voltage (Vturn on), reverse saturation
current (I0), ideality factor (n), barrier height ( b
f ), series resistance
(Rs) and shunt resistance (Rsh) are determined from I-V curves using
Schottky equations. These values of these parameters are also
extracted and verified by applying Cheung’s functions. The
conduction mechanisms are explained from the forward bias I-V
characteristics using the power law.
Abstract: In this study, the effect of greywater irrigation on airwater interfacial area is investigated. Several soil column experiments were conducted for different greywater irrigation to develop the pressure-saturation curves. Surface tension was measured for different greywater concentration and fitted for Gibbs adsorption equation. Pressure-saturation curves show that the reduction of capillary rise stops when it reaches its critical micelle concentration (CMC). A simple theory is derived from pressure-saturation curves for calculating air-water interfacial area in porous medium during greywater irrigation by introducing a term 'hydraulic radius' for the pores. This term diminishes any effect of pore shapes on the air-water interfacial area. The air-water interfacial area was calculated using the pressure-saturation curves and found that it decreases with increasing moisture content. But no significant effect was observed on air-water interfacial area for different greywater irrigation. A maximum of 10% variation in interfacial area was observed at the residual saturation zone.
Abstract: According to the masonry standard the compressive
strength is basically dependent on factors such as the mortar strength
and the relative values of unit and mortar strength. However
interlocking brick has none or less use of mortar. Therefore there is a need to investigate the behavior of masonry walls using interlocking
bricks. In this study a series of tests have been conducted; physical
properties and compressive strength of brick units and masonry walls
were constructed from interlocking bricks and tested under constant
vertical load at different eccentricities. The purpose of the
experimental investigations is to obtain the force displacement curves, analyze the behavior of masonry walls. The results showed
that the brick is categorized as common brick (BS 3921:1985) and severe weathering grade (ASTM C62). The maximum compressive stress of interlocking brick wall is 3.6 N/mm2 and fulfilled the requirement of standard for residential building.
Abstract: In the first part of this paper [6], a method to
determine Frenet apparatus of the space-like curves in Minkowski
space-time is presented. In this work, the mentioned method is
developed for the time-like curves in Minkowski space-time.
Additionally, an example of presented method is illustrated.
Abstract: An organic bulk heterojunction (BHJ) was fabricated using a blended film containing Copper (II) tetrakis(4-acumylphenoxy) phthalocyanine (Tc-CuPc) along with [6,6]-Phenyl C61 butyric acid methyl ester (PCBM). Weight ratio between Tc-CuPc and PCBM was 1:1. The electrical properties of Tc-CuPc: PCBM BHJ were examined. Rectifying nature of the BHJ was displayed by current-voltage (I-V) curves, recorded in dark and at various temperatures. At low voltages, conduction was ohmic succeeded by space-charge limiting current (SCLC) conduction at higher voltages in which exponential trap distribution was dominant. Series resistance, shunt resistance, ideality factor, effective barrier height and mobility at room temperature were found to be 526 4, 482 k4, 3.7, 0.17 eV and 2×10-7 cm2V-1s-1 respectively. Temperature effect towards different BHJ parameters was observed under dark condition.
Abstract: It is difficult to judge ripeness by outward
characteristics such as size or external color. In this paper a nondestructive
method was studied to determine watermelon (Crimson
Sweet) quality. Responses of samples to excitation vibrations were
detected using laser Doppler vibrometry (LDV) technology. Phase
shift between input and output vibrations were extracted overall
frequency range. First and second were derived using frequency
response spectrums. After nondestructive tests, watermelons were
sensory evaluated. So the samples were graded in a range of ripeness
based on overall acceptability (total desired traits consumers).
Regression models were developed to predict quality using obtained
results and sample mass. The determination coefficients of the
calibration and cross validation models were 0.89 and 0.71
respectively. This study demonstrated feasibility of information
which is derived vibration response curves for predicting fruit
quality. The vibration response of watermelon using the LDV method
is measured without direct contact; it is accurate and timely, which
could result in significant advantage for classifying watermelons
based on consumer opinions.
Abstract: The development of shape and size of a crack in a
pressure vessel under uniaxial and biaxial loadings is important in
fitness-for-service evaluations such as leak-before-break. In this
work finite element modelling was used to evaluate the mean stress
and the J-integral around a front of a surface-breaking crack. A
procedure on the basis of ductile tearing resistance curves of high and
low constrained fracture mechanics geometries was developed to
estimate the amount of ductile crack extension for surface-breaking
cracks and to show the evolution of the initial crack shape. The
results showed non-uniform constraint levels and crack driving forces
around the crack front at large deformation levels. It was also shown
that initially semi-elliptical surface cracks under biaxial load
developed higher constraint levels around the crack front than in
uniaxial tension. However similar crack shapes were observed with
more extensions associated with cracks under biaxial loading.
Abstract: The Czech Republic has over the past decade carried out two waves of tax and benefit reforms. The first one took place in 2005–2006 during the left-wing government and the second one has been carried out in 2008 by the right-wing government. Using EUSILC data for selected types of households, the paper assesses changes in the distribution of gross incomes and effects of the changes in taxes and benefits on the distribution of incomes after taxes and a provision of social benefits. The analysis is carried out on four types of households with and without children. The analysis is performed using Lorenz curves and Gini coefficients. The results show that the tax system changes the distribution of incomes less significantly than benefits. The 2006 reform reduced the differential between the Gini coefficient for the gross income and the Gini coefficient after taxes and benefits for households with active parents and one child. Reform in 2008 supported families with children and an reduced the differential between the gross income and income after taxes and benefits for different types of families.
Abstract: This study aimed at developing a forecasting model on the number of Dengue Haemorrhagic Fever (DHF) incidence in Northern Thailand using time series analysis. We developed Seasonal Autoregressive Integrated Moving Average (SARIMA) models on the data collected between 2003-2006 and then validated the models using the data collected between January-September 2007. The results showed that the regressive forecast curves were consistent with the pattern of actual values. The most suitable model was the SARIMA(2,0,1)(0,2,0)12 model with a Akaike Information Criterion (AIC) of 12.2931 and a Mean Absolute Percent Error (MAPE) of 8.91713. The SARIMA(2,0,1)(0,2,0)12 model fitting was adequate for the data with the Portmanteau statistic Q20 = 8.98644 ( x20,95= 27.5871, P>0.05). This indicated that there was no significant autocorrelation between residuals at different lag times in the SARIMA(2,0,1)(0,2,0)12 model.
Abstract: Purpose of this work is to develop an automatic classification system that could be useful for radiologists in the breast cancer investigation. The software has been designed in the framework of the MAGIC-5 collaboration. In an automatic classification system the suspicious regions with high probability to include a lesion are extracted from the image as regions of interest (ROIs). Each ROI is characterized by some features based generally on morphological lesion differences. A study in the space features representation is made and some classifiers are tested to distinguish the pathological regions from the healthy ones. The results provided in terms of sensitivity and specificity will be presented through the ROC (Receiver Operating Characteristic) curves. In particular the best performances are obtained with the Neural Networks in comparison with the K-Nearest Neighbours and the Support Vector Machine: The Radial Basis Function supply the best results with 0.89 ± 0.01 of area under ROC curve but similar results are obtained with the Probabilistic Neural Network and a Multi Layer Perceptron.
Abstract: The curves, of which the square of the distance
between the two points equal to zero, are called minimal or isotropic
curves [4]. In this work, first, necessary and sufficient conditions to
be a Pseudo Helix, which is a special case of such curves, are
presented. Thereafter, it is proven that an isotropic curve-s position
vector and pseudo curvature satisfy a vector differential equation of
fourth order. Additionally, In view of solution of mentioned
equation, position vector of pseudo helices is obtained.
Abstract: This paper is concerned with an improved algorithm
based on the piecewise-smooth Mumford and Shah (MS) functional
for an efficient and reliable segmentation. In order to speed up
convergence, an additional force, at each time step, is introduced
further to drive the evolution of the curves instead of only driven by
the extensions of the complementary functions u + and u - . In our
scheme, furthermore, the piecewise-constant MS functional is
integrated to generate the extra force based on a temporary image that
is dynamically created by computing the union of u + and u - during
segmenting. Therefore, some drawbacks of the original algorithm,
such as smaller objects generated by noise and local minimal problem
also are eliminated or improved. The resulting algorithm has been
implemented in Matlab and Visual Cµ, and demonstrated efficiently
by several cases.