Abstract: Reinforced concrete stair slabs with mid landings i.e.
Dog-legged shaped are conventionally designed as per specifications
of standard codes of practices which guide about the effective span
according to the varying support conditions. Presently, the behavior
of such slabs has been investigated using Finite Element method. A
single flight stair slab with landings on both sides and supported at
ends on wall, and a multi flight stair slab with landings and six
different support arrangements have been analyzed. The results
obtained for stresses, strains and deflections are used to describe the
behavior of such stair slabs, including locations of critical moments
and deflections. Values of critical moments obtained by F.E. analysis
have also have been compared with that obtained from conventional
analysis. Analytical results show that the moments are also critical
near the kinks i.e. junction of mid-landing and inclined waist slab.
This change in the behavior of dog-legged stair slab may be due to
continuity of the material in transverse direction in two landings
adjoining the waist slab, hence additional stiffness achieved. This
change in the behavior is generally not taken care of in conventional
method of design.
Abstract: The objective of this work was to examine the changes
in non destructive properties caused by carbonation of CEM II
mortar. Samples of CEM II mortar were prepared and subjected to
accelerated carbonation at 20°C, 65% relative humidity and 20% CO2
concentration. We examined the evolutions of the gas permeability,
the thermal conductivity, the thermal diffusivity, the volume of the
solid phase by helium pycnometry, the longitudinal and transverse
ultrasonic velocities. The principal contribution of this work is that,
apart of the gas permeability, changes in other non destructive
properties have never been studied during the carbonation of cement
materials. These properties are important in predicting/measuring the
durability of reinforced concrete in CO2 environment. The
carbonation depth and the porosity accessible to water were also
reported in order to explain comprehensively the changes in non
destructive parameters.
Abstract: Existing underground pipe jacking methods use a
reinforcing rod in a steel tube to obtain structural stiffness. However,
some problems such as inconvenience of works and expensive
materials resulted from limited working space and reinforcing works
are existed. To resolve these problems, a new pipe jacking method,
namely PST (Prestressed Segment Tunnel) method, was developed
which used joint to connect the steel segment and form erection
structure. For evaluating the flexural capacity of the PST method
structure, a experimental test was conducted. The parameters
considered in the test were span-to-depth ratio of segment, diameter of
steel tube at the corner, prestressing force, and welding of joint. The
flexural behaviours with the effect of load capacity in serviceability
state according to different parameters were examined.. The frame
with long segments could increase flexural stiffness and the specimen
with large diameter of concave corner showed excellent resistance
ability to the negative moment. In addition, welding of joints increased
the flexural capacity.
Abstract: This paper deals with behavior and capacity of
punching shear force for flat slabs produced from steel fiber
reinforced self compacting concrete (SFRSCC) by application
nonlinear finite element method. Nonlinear finite element analysis on
nine slab specimens was achieved by using ANSYS software. A
general description of the finite element method, theoretical modeling
of concrete and reinforcement are presented. The nonlinear finite
element analysis program ANSYS is utilized owing to its capabilities
to predict either the response of reinforced concrete slabs in the post
elastic range or the ultimate strength of a flat slabs produced from
steel fiber reinforced self compacting concrete (SFRSCC). In order to
verify the analytical model used in this research using test results of
the experimental data, the finite element analysis were performed
then a parametric study of the effect ratio of flexural reinforcement,
ratio of the upper reinforcement, and volume fraction of steel fibers
were investigated. A comparison between the experimental results
and those predicted by the existing models are presented. Results and
conclusions may be useful for designers, have been raised, and
represented.
Abstract: The paper reflects current state of popularization of
static elasticity modulus of concrete. This parameter is undoubtedly
very important for designing of concrete structures, and very often
neglected and rarely determined before designing concrete
technology itself. The paper describes assessment and comparison of
four mix designs with almost constant dosage of individual
components. The only difference is area of origin of small size
fraction of aggregate 0/4. Development of compressive strength and
static elasticity modulus at the age of 7, 28 and 180 days were
observed. As the experiment showed, designing of individual
components and their quality are the basic factor influencing
elasticity modulus of current concrete.
Abstract: In this paper, a framework for the simplification and
standardization of metaheuristic related parameter-tuning by applying
a four phase methodology, utilizing Design of Experiments and
Artificial Neural Networks, is presented. Metaheuristics are multipurpose
problem solvers that are utilized on computational optimization
problems for which no efficient problem specific algorithm
exist. Their successful application to concrete problems requires the
finding of a good initial parameter setting, which is a tedious and
time consuming task. Recent research reveals the lack of approach
when it comes to this so called parameter-tuning process. In the
majority of publications, researchers do have a weak motivation for
their respective choices, if any. Because initial parameter settings
have a significant impact on the solutions quality, this course of
action could lead to suboptimal experimental results, and thereby
a fraudulent basis for the drawing of conclusions.
Abstract: It is necessary to evaluate the bridges conditions and
strengthen bridges or parts of them. The reinforcement necessary due
to some reasons can be summarized as: First, a changing in use of
bridge could produce internal forces in a part of structural which
exceed the existing cross-sectional capacity. Second, bridges may
also need reinforcement because damage due to external factors
which reduced the cross-sectional resistance to external loads. One of
other factors could listed here its misdesign in some details, like
safety of bridge or part of its.This article identify the design demands
of Qing Shan bridge located in is in Heilongjiang Province He gang -
Nen Jiang Road 303 provincial highway, Wudalianchi area, China, is
an important bridge in the urban areas. The investigation program
was include the observation and evaluate the damage in T- section
concrete beams , prestressed concrete box girder bridges section in
additional evaluate the whole state of bridge includes the pier ,
abutments , bridge decks, wings , bearing and capping beam, joints,
........etc. The test results show that the bridges in general structural
condition are good. T beam span No 10 were observed, crack
extended upward along the ribbed T beam, and continue to the T
beam flange. Crack width varying between 0.1mm to 0.4mm, the
maximum about 0.4mm. The bridge needs to be improved flexural
bending strength especially at for T beam section.
Abstract: In this study, the thermal and mechanical properties of
basalt fibre reinforced concrete were investigated. The volume
fractions of basalt fibre of (0.1, 0.2, 0.3, and 0.5% by total mix
volume) were used. Properties such as heat transfer, compressive and
splitting tensile strengths were examined. Results indicated that the
strength increases with increase the fibre content till 0.3% then there
is a slight reduction when 0.5% fibre used. Lower amount of heat
conducted through the thickness of concrete specimens than the
conventional concrete was also recorded.
Abstract: The objective of this work is to study the influence of the properties of the substrate on the retrofit (thin repair) of damaged concrete elements, with the SCC. Fluidity, principal characteristic of the SCC, would enable it to cover and adhere to the concrete to be repaired. Two aspects of repair are considered, the bond (Adhesion) and the tensile strength and the cracking. The investigation is experimental; It was conducted over test specimens made up of ordinary concrete prepared and hardened in advance (the material to be repaired) over which a self compacting concrete layer is cast. Three alternatives of SC concrete and one ordinary concrete (comparison) were tested. It appears that the self-compacting concrete constitutes a good material for repairing. It follows perfectly the surfaces- forms to be repaired and allows a perfect bond. Fracture tests made on specimens of self-compacting concrete show a brittle behaviour. However when a small percentage of fibres is added, the resistance to cracking is very much improve.
Abstract: In order to calculate the flexural strength of
normal-strength concrete (NSC) beams, the nonlinear actual concrete
stress distribution within the compression zone is normally replaced
by an equivalent rectangular stress block, with two coefficients of α
and β to regulate the intensity and depth of the equivalent stress
respectively. For NSC beams design, α and β are usually assumed
constant as 0.85 and 0.80 in reinforced concrete (RC) codes. From an
earlier investigation of the authors, α is not a constant but significantly
affected by flexural strain gradient, and increases with the increasing
of strain gradient till a maximum value. It indicates that larger
concrete stress can be developed in flexure than that stipulated by
design codes. As an extension and application of the authors- previous
study, the modified equivalent concrete stress block is used here to
produce a series of design charts showing the maximum design limits
of flexural strength and ductility of singly- and doubly- NSC beams,
through which both strength and ductility design limits are improved
by taking into account strain gradient effect.
Abstract: In this paper, experimental testing and numerical analysis were used to investigate the effect of tube thickness on the face bending for concrete filled hollow sections connected to other structural members using Extended Hollobolts. Six samples were tested experimentally by applying pull-out load on the bolts. These samples were designed to fail by column face bending. The main variable in all tests is the column face thickness. Finite element analyses were also performed using ABAQUS 6.11 to extend the experimental results and to quantify the effect of column face thickness. Results show that, the column face thickness has a clear impact on the connection strength and stiffness. However, the amount of improvement in the connection stiffness by changing the column face thickness from 5mm to 6.3mm seems to be higher than that when increasing it from 6.3mm to 8mm. The displacement at which the bolts start pulling-out from their holes increased with the use of thinner column face due to the high flexibility of the section. At the ultimate strength, the yielding of the column face propagated to the column corner and there was no yielding in its walls. After the ultimate resistance is reached, the propagation of the yielding was mainly in the column face with a miner yielding in the walls.
Abstract: In this study the effect of incorporation of recycled
glass-fibre reinforced polymer (GFRP) waste materials, obtained by
means of milling processes, on mechanical behaviour of polyester
polymer mortars was assessed. For this purpose, different contents of
recycled GFRP waste powder and fibres, with distinct size gradings,
were incorporated into polyester based mortars as sand aggregates
and filler replacements. Flexural and compressive loading capacities
were evaluated and found better than unmodified polymer mortars.
GFRP modified polyester based mortars also show a less brittle
behaviour, with retention of some loading capacity after peak load.
Obtained results highlight the high potential of recycled GFRP waste
materials as efficient and sustainable reinforcement and admixture for
polymer concrete and mortars composites, constituting an emergent
waste management solution.
Abstract: This article presents the analysis of experimental values regarding cracking pattern, specific strains and deformability for reinforced high strength concrete beams. The beams have the concrete class C80/95 and a longitudinal reinforcement ratio of 2.01%, respectively 3.39%. The elements were subjected to flexure under static short-term and long-term loading. The experimental values are compared with calculation values using the design relationships according to Eurocode 2.
Abstract: As the world move to the accomplishment of Performance Based Engineering philosophies in seismic design of Civil Engineering structures, new seismic design provisions require Structural Engineers to perform both static and dynamic analysis for the design of structures. While Linear Equivalent Static Analysis is performed for regular buildings up to 90m height in zone I and II, Dynamic Analysis should be performed for regular and irregular buildings in zone IV and V. Dynamic Analysis can take the form of a dynamic Time History Analysis or a linear Response Spectrum Analysis. In present study, Multi-storey irregular buildings with 20 stories have been modeled using software packages ETABS and SAP 2000 v.15 for seismic zone V in India. This paper also deals with the effect of the variation of the building height on the structural response of the shear wall building. Dynamic responses of building under actual earthquakes, EL-CENTRO 1949 and CHI-CHI Taiwan 1999 have been investigated. This paper highlights the accuracy and exactness of Time History analysis in comparison with the most commonly adopted Response Spectrum Analysis and Equivalent Static Analysis.
Abstract: Demolitions of buildings have created a lot of waste
and one of it is clay bricks. The waste clay bricks were ground to
roughly cement fineness and used to partially replaced cement at
10%, 20% and 30% with w/b ratio of 0.6 and tested at 7, 28, 60, 90
and 120 days. The result shows that the compressive strength of GCB
concrete increases over age however, decreases as the level of
replacements increases. It was also found that 10% replacement of
GCB gave the highest compressive strength, however for optimum
replacement, 30% was chosen as it still attained strength of grade 30
concrete. In terms of durability performances, results show that GCB
replacement up to 30% was found to be efficient in reducing water
absorption as well as water permeability. These studies show that
GCB has the potential to be used as partial cement replacement in
making concrete.
Abstract: A simple mobile engine-driven pneumatic paddy
collector made of locally available materials using local
manufacturing technology was designed, fabricated, and tested for
collecting and bagging of paddy dried on concrete pavement. The
pneumatic paddy collector had the following major components:
radial flat bladed type centrifugal fan, power transmission system,
bagging area, frame and the conveyance system. Results showed
significant differences on the collecting capacity, noise level, and fuel
consumption when rotational speed of the air mover shaft was varied.
Other parameters such as collecting efficiency, air velocity,
augmented cracked grain percentage, and germination rate were not
significantly affected by varying rotational speed of the air mover
shaft. The pneumatic paddy collector had a collecting efficiency of
99.33 % with a collecting capacity of 2685.00 kg/h at maximum
rotational speed of centrifugal fan shaft of about 4200 rpm. The
machine entailed an investment cost of P 62,829.25. The break-even
weight of paddy was 510,606.75 kg/yr at a collecting cost of 0.11
P/kg of paddy. Utilizing the machine for 400 hours per year
generated an income of P 23,887.73. The projected time needed to
recover cost of the machine based on 2685 kg/h collecting capacity
was 2.63 year.
Abstract: In the present article, effect of non-uniform excitation
of reservoir bottom on nonlinear response of concrete gravity dams is
considered. Anisotropic damage mechanics approach is used to model nonlinear behavior of mass concrete in 2D space. The tallest
monolith of Pine Flat dam is selected as a case study. The horizontal
and vertical components of 1967 Koyna earthquake is used to excite
the system. It is found that crest response and stresses within the dam body decrease significantly when the reservoir is excited nonuniformly. In addition, the crack profiles within the dam body and in vicinity of the neck decreases.
Abstract: Data Structures and Algorithms is a module in most
Computer Science or Information Technology curricula. It is one of
the modules most students identify as being difficult. This paper
demonstrates how programming a solution for Sudoku can make
abstract concepts more concrete. The paper relates concepts of a
typical Data Structures and Algorithms module to a step by step
solution for Sudoku in a human type as opposed to a computer
oriented solution.
Abstract: As is known, one of the priority directions of research
works of natural sciences is introduction of applied section of
contemporary mathematics as approximate and numerical methods to
solving integral equation into practice. We fare with the solving of
integral equation while studying many phenomena of nature to whose
numerically solving by the methods of quadrature are mainly applied.
Taking into account some deficiency of methods of quadrature for
finding the solution of integral equation some sciences suggested of
the multistep methods with constant coefficients. Unlike these papers,
here we consider application of hybrid methods to the numerical
solution of Volterra integral equation. The efficiency of the suggested
method is proved and a concrete method with accuracy order p = 4
is constructed. This method in more precise than the corresponding
known methods.
Abstract: In recent years, rehabilitation has been the subject of extensive research due to increased spending on building work and repair of built works. In all cases, it is absolutely essential to carry out methods of strengthening or repair of structural elements, and that following an inspection analysis and methodology of a correct diagnosis. The reinforced concrete columns are important elements in building structures. They support the vertical loads and provide bracing against the horizontal loads. This research about the behavior of reinforced concrete rectangular columns, rehabilitated by concrete liner, confinement FRP fabric, steel liner or cage formed by metal corners. It allows comparing the contributions of different processes used perspective section resistance elements rehabilitated compared to that is not reinforced or repaired. The different results obtained revealed a considerable gain in bearing capacity failure of reinforced sections cladding concrete, metal bracket, steel plates and a slight improvement to the section reinforced with fabric FRP. The use of FRP does not affect the weight of the structures, but the use of different techniques cladding increases the weight of elements rehabilitated and therefore the weight of the building which requires resizing foundations.