Abstract: In this paper, a new SMC (Sliding Mode Control)
method with MP (Model Predictive Control) integral action for the
slip suppression of EV (Electric Vehicle) under braking is proposed.
The proposed method introduce the integral term with standard SMC
gain , where the integral gain is optimized for each control period by
the MPC algorithms. The aim of this method is to improve the safety
and the stability of EVs under braking by controlling the wheel slip
ratio. There also include numerical simulation results to demonstrate
the effectiveness of the method.
Abstract: Singular value decomposition based optimisation of
geometric design parameters of a 5-speed gearbox is studied. During
the optimisation, a four-degree-of freedom torsional vibration model
of the pinion gear-wheel gear system is obtained and the minimum
singular value of the transfer matrix is considered as the objective
functions. The computational cost of the associated singular value
problems is quite low for the objective function, because it is only
necessary to compute the largest and smallest singular values (μmax
and μmin) that can be achieved by using selective eigenvalue solvers;
the other singular values are not needed. The design parameters are
optimised under several constraints that include bending stress,
contact stress and constant distance between gear centres. Thus, by
optimising the geometric parameters of the gearbox such as, the
module, number of teeth and face width it is possible to obtain a
light-weight-gearbox structure. It is concluded that the all optimised
geometric design parameters also satisfy all constraints.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: This paper presents the ‘Eye Ball Motion Controlled
Wheelchair using IR Sensors’ for the elderly and differently abled
people. In this eye tracking based technology, three Proximity
Infrared (IR) sensor modules are mounted on an eye frame to trace
the movement of the iris. Since, IR sensors detect only white objects;
a unique sequence of digital bits is generated corresponding to each
eye movement. These signals are then processed via a micro
controller IC (PIC18F452) to control the motors of the wheelchair.
The potential and efficiency of previously developed rehabilitation
systems that use head motion, chin control, sip-n-puff control, voice
recognition, and EEG signals variedly have also been explored in
detail. They were found to be inconvenient as they served either
limited usability or non-affordability. After multiple regression
analyses, the proposed design was developed as a cost-effective,
flexible and stream-lined alternative for people who have trouble
adopting conventional assistive technologies.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: Present study is carried out on six lane divided urban
arterial road in Patna and Pune city of India. Both the road having
distinct differences in terms of the vehicle composition and the road
side parking. Arterial road in Patan city has 33% of non-motorized
mode, whereas Pune arterial road dominated by 65% of Two wheeler.
Also road side parking is observed in Patna city. The field studies
using videography techniques are carried out for traffic data
collection. Data are extracted for one minute duration for vehicle
composition, speed variation and flow rate on selected arterial road of
the two cities. Speed flow relationship is developed and capacity is
determine. Equivalency factor in terms of dynamic car unit is
determine to represent the vehicle is single unit. The variation in the
capacity due to side friction, presence of non motorized traffic and
effective utilization of lane width is compared at concluding remarks.
Abstract: The efficiency of the actuation system of exoskeletons
and active orthoses for lower limbs is a significant aspect of the
design of such devices because it affects their efficacy. The F-IVT is
an innovative actuation system to power artificial knee joint with
energy recovery capabilities. Its key and non-conventional elements
are a flywheel that acts as a mechanical energy storage system, and
an Infinitely Variable Transmission (IVT). The design of the F-IVT
can be optimized for a certain walking condition, resulting in a heavy
reduction of both the electric energy consumption and of the electric
peak power. In this work, by means of simulations of level ground
walking at different speeds, it is demonstrated that the F-IVT is still
an advantageous actuator which permits to save energy consumption
and to downsize the electric motor even when it does not work in
nominal conditions.
Abstract: In this paper we propose a discrete tracking control of
nonholonomic mobile robots with two degrees of freedom. The
electromechanical model of a mobile robot moving on a horizontal
surface without slipping, with two rear wheels controlled by two
independent DC electric, and one front roal wheel is considered. We
present backstepping design based on the Euler approximate discretetime
model of a continuous-time plant. Theoretical considerations are
verified by numerical simulation.
Abstract: In this paper, a new design of spherical robotic system
based on the concepts of gimbal structure and gyro dynamics is
presented. Robots equipped with multiple wheels and complex
steering mechanics may increase the weight and degrade the energy
transmission efficiency. In addition, the wheeled and legged robots are
relatively vulnerable to lateral impact and lack of lateral mobility.
Therefore, the proposed robotic design uses a spherical shell as the
main body for ground locomotion, instead of using wheel devices.
Three spherical shells are structured in a similar way to a gimbal
device and rotate like a gyro system. The design and mechanism of the
proposed robotic system is introduced. In addition, preliminary results
of the dynamic model based on the principles of planar rigid body
kinematics and Lagrangian equation are included. Simulation results
and rig construction are presented to verify the concepts.
Abstract: This research aimed to study the characteristics of a
community in the social, economic and cultural context. This
research used interviews and surveys of the members in the Patthana
Soi Ranongklang community, Dusit District, Bangkok. The results
are as follows: In terms of overall conditions and characteristics, the
Patthana Soi Ranongklang community is located on the property of
the Treasury Department. 50 years ago, the location of this
community consisted of paddy fields with limited convenience in
terms of transportation. Rama V Road was only a small narrow road
accessed only by three-wheelers there were no buses. The majority of
community members moved in from Mak Khawan Rangsan Bridge.
Thus, most community members were either workers or government
officials as they were routers not the owners of the land. Therefore,
there were no primary occupations within the 7 acres of this
community. The development of the community started in 1981. At
present, the community is continuously being developed and
modernization is rapidly flowing in. One of the reasons was because
the main roads were widened, especially Rama V Road that allows
more convenient transportation, leading to heightened citizens’
convenience. In terms of the economy and society, Rama V Road
causes the research to find out the development and expansion of
change in the conditions of the area and buildings. Some buildings
were improved and changed along the time, as well as the
development of new facilities that caused the community members to
continually become more materialistic. In the community, it has well
organized and managed jobs to each part of community members,
and areas were improved to allow the new buildings and apartments.
The trend of jobs became more varied, in terms of both jobs at home,
such as workers, merchandizing and small own businesses, and the
community jobs outside, which became much more convenient to car
drivers as they got used to the narrow roads inside the community.
The location of the community next to Rama V Road also allows
assistance from government agencies to reach the community with
ease. Moreover, the welfare of the community was well taken care of
by the community committee. In terms of education, the research
found that there are two schools: Wat Pracharabuedham School and
Wat Noi Noppakun School that are providing education within the
community. The majority in the community have received Bachelor
degrees. In areas of culture, the research found that the culture,
traditions and beliefs of people in the community were mainly
transferred from the old community: the majorities are Buddhists, so
especially beliefs in Buddhism; the main reason for this is because
the old community was situated near Wat Makut Kasattriyaram.
Therefore, the community members have always had Buddhist
temples as the centre of the community. Later years, more citizens
moved along culture in and bring traditions and beliefs with them.
The community members also took part in building a Dharma hall
named Wat Duang Jai which is 72 year old.
Abstract: As the current status and growth of Indian automobile
industry is remarkable, transportation sectors are the main concern in
terms of energy security and climate change. Due to rising demand of
fuel and its dependency on foreign countries that affects the GDP of
nation, suggests that penetration of electrical vehicle will increase in
near future. So in this context analysis is done if the 10 percent of
conventional vehicles including cars, three wheelers and two
wheelers becomes electrical vehicles in near future which is also a
part of Nations Electric Mobility Mission Plan then the saving which
improves the nation’s economy is analyzed in detail. Whether the
Indian electricity grid is capable of taking this load with current
generation and demand all over the country is also analyzed in detail.
Current situation of Indian grid is analyzed and how the gap between
generation and demand can be reduced is discussed in terms of
increasing generation capacity and energy conservation measures.
Electrical energy conservation measures in Industry and especially in
rural areas have been analyzed to improve performance of Indian
electricity grid in context of electrical vehicle penetration in near
future. Author was a part of Vishvakarma yojna in which energy
losses were measured in 255 villages of Gujarat and solutions were
suggested to mitigate them and corresponding reports was submitted
to the authorities of Gujarat government.
Abstract: This paper presents the hardware implemented and
validation for a special system to assist the unprofessional users of
car with back trailers. The system consists of two platforms; the front
car platform (C) and the trailer platform (T). The main objective is to
control the Trailer platform using the actuators found in the front
platform (c). The mobility of the platform (C) is investigated and
inverse and forward kinematics model is obtained for both platforms
(C) and (T).The system is simulated using Matlab M-file and the
simulation examples results illustrated the system performance. The
system is constructed with a hardware setup for the front and trailer
platform. The hardware experimental results and the simulated
examples outputs showed the validation of the hardware setup.
Abstract: The substantial similarity of fatigue mechanism in a
new test rig for rolling contact fatigue (RCF) has been investigated. A
new reduced-scale test rig is designed to perform controlled RCF
tests in wheel-rail materials. The fatigue mechanism of the rig is
evaluated in this study using a combined finite element-fatigue
prediction approach. The influences of loading conditions on fatigue
crack initiation have been studied. Furthermore, the effects of some
artificial defects (squat-shape) on fatigue lives are examined. To
simulate the vehicle-track interaction by means of the test rig, a threedimensional
finite element (FE) model is built up. The nonlinear
material behaviour of the rail steel is modelled in the contact
interface. The results of FE simulations are combined with the critical
plane concept to determine the material points with the greatest
possibility of fatigue failure. Based on the stress-strain responses, by
employing of previously postulated criteria for fatigue crack initiation
(plastic shakedown and ratchetting), fatigue life analysis is carried
out. The results are reported for various loading conditions and
different defect sizes. Afterward, the cyclic mechanism of the test rig
is evaluated from the operational viewpoint. The results of fatigue
life predictions are compared with the expected number of cycles of
the test rig by its cyclic nature. Finally, the estimative duration of the
experiments until fatigue crack initiation is roughly determined.
Abstract: A new small–scale test rig developed for rolling
contact fatigue (RCF) investigations in wheel–rail material. This
paper presents the scaling strategy of the rig based on dimensional
analysis and mechanical modelling. The new experimental rig is
indeed a spinning frame structure with multiple wheel components
over a fixed rail-track ring, capable of simulating continuous wheelrail
contact in a laboratory scale. This paper describes the
dimensional design of the rig, to derive its overall scaling strategy
and to determine the key elements’ specifications. Finite element
(FE) modelling is used to simulate the mechanical behavior of the rig
with two sample scale factors of 1/5 and 1/7. The results of FE
models are compared with the actual railway system to observe the
effectiveness of the chosen scales. The mechanical properties of the
components and variables of the system are finally determined
through the design process.
Abstract: Assistive robotics are playing a vital role in advancing the quality of life for disable people. There exist wide range of systems that can control and guide autonomous mobile robots. The objective of the control system is to guide an autonomous mobile robot using the movement of eyes by means of EOG signal. The EOG signal is acquired using Ag/AgCl electrodes and this signal is processed by a microcontroller unit to calculate the eye gaze direction. Then according to the guidance control strategy, the control commands of the wheelchair are sent. The classification of different eye movements allows us to generate simple code for controlling the wheelchair. This work was aimed towards developing a usable and low-cost assistive robotic wheel chair system for disabled people. To live more independent life, the system can be used by the handicapped people especially those with only eye-motor coordination.
Abstract: In this paper, a 2DOF (two degrees of freedom) PID (Proportional-Integral-Derivative) controller based on MPC (Model predictive control) algorithm fo slip suppression of EV (Electric Vehicle) under braking is proposed. The proposed method aims to improve the safety and the stability of EVs under braking by controlling the wheel slip ration. There also include numerical simulation results to demonstrate the effectiveness of the method.
Abstract: According to the independence, accuracy and controllability of the driving/braking torque of the distributed drive electric vehicle, a control strategy of differential drive assisted steering was designed. Firstly, the assisted curve under different speed and steering wheel torque was developed and the differential torques were distributed to the right and left front wheels. Then the steering return ability assisted control algorithm was designed. At last, the joint simulation was conducted by CarSim/Simulink. The result indicated: the differential drive assisted steering algorithm could provide enough steering drive-assisted under low speed and improve the steering portability. Along with the increase of the speed, the provided steering drive-assisted decreased. With the control algorithm, the steering stiffness of the steering system increased along with the increase of the speed, which ensures the driver’s road feeling. The control algorithm of differential drive assisted steering could avoid the understeer under low speed effectively.
Abstract: The objectives of this study are to increase tourism products and to develop family agro-tourism. The research methodology was to analyze internal and external situations according to MP-MF and the MC-STEPS principles.
The results of this study highlight following necessary improvements; extend the cycling routes, increase the number of bicycle rental shops, offer a recreation place for the elders, organize a space for the floating market products and increase tourism activities throughout the year. In ‘places or distribution channel’ we discuss the improvement of facilities, specifically the routes to facilitate elder visitors and visitors on wheelchairs and furthermore the arrangement of educational trips to relevant centers in the community. In ‘promotions’, we discuss the implementation of an “all inclusive package” were the agro-tourism program, health-conscious program and the elderly fun program converge.
Abstract: This paper presents the experimental results of high-density polyethylene cable spacers for 22 kV distribution systems under salt water dip wheel test based on IEC 62217. The strength of anti-tracking and anti-erosion of cable spacer surface was studied in this study. During the test, dry band arc and corona discharge were observed on cable spacer surface. After 30,000 cycles of salt water dip wheel test, obviously surface erosion and tracking were observed especially on the ground end. Chemical analysis results by fourier transforms infrared spectroscopy showed chemical changed from oxidation and carbonization reaction on tested cable spacer. Increasing of C=O and C=C bonds confirmed occurrence of these reactions.
Abstract: Flow coastdown phenomena are very important to secure nuclear fuel integrity during loss of off-site power accidents. In this study, primary coolant flow coastdown phenomena are investigated for the Jordan Research and Training Reactor (JRTR) using a simulation software package, Modular Modeling System (MMS). Two MMS models are built. The first one is a simple model to investigate the characteristics of the primary coolant pump only. The second one is a model for a simulation of the Primary Coolant System (PCS) loop, in which all the detailed design data of the JRTR PCS system are modeled, including the geometrical arrangement data. The same design data for a PCS pump are used for both models. Coastdown curves obtained from the two models are compared to study the PCS loop coolant inertia effect on a flow coastdown. Results showed that the loop coolant inertia effect is found to be small in the JRTR PCS loop, i.e., about one second increases in a coastdown half time required to halve the coolant flow rate. The effects of different flywheel inertia on the flow coastdown are also investigated. It is demonstrated that the coastdown half time increases with the flywheel inertia linearly. The designed coastdown half time is proved to be well above the design requirement for the fuel integrity.