Abstract: The Yazd-Ardakan basin in Central Iran has two separated aquifers. The shallow unconfined aquifer is supplies 40 Qanats. The deep saturated confined aquifer is the main water storage. Due to over-withdrawal, water table has been decreasing during last 25 years. Recent study shows that the shortage of the aquifer is about 16 meters and land subsidence is 0.5 - 1.2 meters. Long deep cracks are found just above the aquifer and devour the irrigation water and floods. Although the most cracks direction is NW-SE and could be compared to the main direction of YA basin, there is no direct evidence for relation between land subsidence and the huge cracks. Large-scale water pumping has been decreased the water pressure in aquifer. The pressure decline disturbed the balance and increased the pressure of overlying sediments. So porosity decreased and compaction started. Then, sediments compaction developed and made land subsidence and some huge cracks slowly.
Abstract: Pulse width modulation (PWM) techniques have been
the subject of intensive research for different industrial and power
sector applications. A large variety of methods, different in concept
and performance, have been newly developed and described. This
paper analyzes the comparative merits of Sinusoidal Pulse Width
Modulation (SPWM) and Space Vector Pulse Width Modulation
(SVPWM) techniques and the suitability of these techniques in a
Shunt Active Filter (SAF). The objective is to select the scheme that
offers effective utilization of DC bus voltage and also harmonic
reduction at the input side. The effectiveness of the PWM techniques
is tested in the SAF configuration with a non linear load. The
performance of the SAF with the SPWM and (SVPWM) techniques
are compared with respect to the THD in source current. The study
reveals that in the context of closed loop SAF control with the
SVPWM technique there is only a minor improvement in THD. The
utilization of the DC bus with SVPWM is also not significant
compared to that with SPWM because of the non sinusoidal
modulating signal from the controller in SAF configuration.
Abstract: High Speed PM Generators driven by micro-turbines
are widely used in Smart Grid System. So, this paper proposes
comparative study among six classical, optimized and genetic
analytical design cases for 400 kW output power at tip speed 200
m/s. These six design trials of High Speed Permanent Magnet
Synchronous Generators (HSPMSGs) are: Classical Sizing;
Unconstrained optimization for total losses and its minimization;
Constrained optimized total mass with bounded constraints are
introduced in the problem formulation. Then a genetic algorithm is
formulated for obtaining maximum efficiency and minimizing
machine size. In the second genetic problem formulation, we attempt
to obtain minimum mass, the machine sizing that is constrained by
the non-linear constraint function of machine losses. Finally, an
optimum torque per ampere genetic sizing is predicted. All results are
simulated with MATLAB, Optimization Toolbox and its Genetic
Algorithm. Finally, six analytical design examples comparisons are
introduced with study of machines waveforms, THD and rotor losses.
Abstract: A 10bit, 40 MSps, sample and hold, implemented in 0.18-μm CMOS technology with 3.3V supply, is presented for application in the front-end stage of an analog-to-digital converter. Topology selection, biasing, compensation and common mode feedback are discussed. Cascode technique has been used to increase the dc gain. The proposed opamp provides 149MHz unity-gain bandwidth (wu), 80 degree phase margin and a differential peak to peak output swing more than 2.5v. The circuit has 55db Total Harmonic Distortion (THD), using the improved fully differential two stage operational amplifier of 91.7dB gain. The power dissipation of the designed sample and hold is 4.7mw. The designed system demonstrates relatively suitable response in different process, temperature and supply corners (PVT corners).
Abstract: As wind, solar and other clean and green energy
sources gain popularity worldwide, engineers are seeking ways to
make renewable energy systems more affordable and to integrate
them with existing ac power grids. In the present paper an attempt
has been made for integrating the PV arrays to the smart nano grid
using an artificial intelligent (AI) based solar powered cascade multilevel
inverter. The AI based controller switching scheme has been
used for improving the power quality by reducing the Total Harmonic
Distortion (THD) of the multi-level inverter output voltage.
Abstract: Chemical detection is still a continuous challenge when
it comes to designing single-walled carbon nanotube (SWCNT)
sensors with high selectivity, especially in complex chemical
environments. A perfect example of such an environment would be in
thermally oxidized soybean oil. At elevated temperatures, oil oxidizes
through a series of chemical reactions which results in the formation of
monoacylglycerols, diacylglycerols, oxidized triacylglycerols, dimers,
trimers, polymers, free fatty acids, ketones, aldehydes, alcohols,
esters, and other minor products. In order to detect the rancidity of
oxidized soybean oil, carbon nanotube chemiresistor sensors have
been coated with polyethylenimine (PEI) to enhance the sensitivity
and selectivity. PEI functionalized SWCNTs are known to have a high
selectivity towards strong electron withdrawing molecules. The
sensors were very responsive to different oil oxidation levels and
furthermore, displayed a rapid recovery in ambient air without the
need of heating or UV exposure.
Abstract: The present work demonstrates the design and simulation of a fuzzy control of an air conditioning system at different pressures. The first order Sugeno fuzzy inference system is utilized to model the system and create the controller. In addition, an estimation of the heat transfer rate and water mass flow rate injection into or withdraw from the air conditioning system is determined by the fuzzy IF-THEN rules. The approach starts by generating the input/output data. Then, the subtractive clustering algorithm along with least square estimation (LSE) generates the fuzzy rules that describe the relationship between input/output data. The fuzzy rules are tuned by Adaptive Neuro-Fuzzy Inference System (ANFIS). The results show that when the pressure increases the amount of water flow rate and heat transfer rate decrease within the lower ranges of inlet dry bulb temperatures. On the other hand, and as pressure increases the amount of water flow rate and heat transfer rate increases within the higher ranges of inlet dry bulb temperatures. The inflection in the pressure effect trend occurs at lower temperatures as the inlet air humidity increases.
Abstract: In this paper, we consider a designed and
implemented phase-cutting dimmer. In fact, the dimmer is closed
loop and a microcontroller calculates and then regulates the firing
delay angles of each channel. Depending on the firing angle, the
harmonic distortion in the input current will not comply with
international standards, such as IEC 61000-3-2 (class C equipments).
For solving this problem, eight harmonic compensators have been
added to the dimmer. So, the proposed dimmer has a little harmonic
distortion in the input current whereas conventional phase-cutting
dimmers are not so. Sensitivity and removed THD of the proposed
dimmer will be presented.
Abstract: Fluorescent and WOLED are widely used because it consumes less energy. However, both lamps cause a harmonics because it has semiconductors components. Harmonic is a distorted sinusoidal electric wave and cause excess heat. This study compares the amount of harmonics generated by both lamps. The test shows that both lamps have THDv(Total Harmonics Distortion of Voltage) almost the same with average 2.5% while the average of WOLED's THDi(Total Harmonics Distortion of Current) is lower than fluorescent has. The average WOLED's THDi is 29.10 % and fluorescent's 'THDi is 87. 23 %.
Abstract: Nowadays Multilevel inverters are widely using in various applications. Modulation strategy at fundamental switching frequency like, SHEPWM is prominent technique to eliminate lower order of harmonics with less switching losses and better harmonic profile. The equations which are formed by SHE are highly nonlinear transcendental in nature, there may exist single, multiple or even no solutions for a particular MI. However, some loads such as electrical drives, it is required to operate in whole range of MI. In order to solve SHE equations for whole range of MI, intelligent techniques are well suited to solve equations so as to produce lest %THDV. Hence, this paper uses Continuous genetic algorithm for minimising harmonics. This paper also presents wavelet based analysis of harmonics. The developed algorithm is simulated and %THD from FFT analysis and Wavelet analysis are compared. MATLAB programming environment and SIMULINK models are used whenever necessary.
Abstract: To estimate the risks of dam failure phenomenon, it is necessary to understand this phenomenon and the involved governing factors. Overtopping and piping are the two main reasons of earthdam failures. In the piping context, the piping is determined as a phenomenon which is occurred between two phases, the water liquid and the solid soil. In this investigation, the onset of piping and its development, as well as the movement of water in soil, are numerically approached. In this regard, a one-dimensional numerical model based on the mass-conserving finite-volume method is developed and applied in order to simulate the piping phenomenon in a continuous circular tunnel of given initial length and radius, located between upstream and downstream. The simulation result includes the time-variations of radius along the tunnel until the radius value reaches its critical and the piping phenomenon converts to overtopping.
Abstract: This paper describes a low-voltage and low-power
channel selection analog front end with continuous-time low pass
filters and highly linear programmable gain amplifier (PGA). The
filters were realized as balanced Gm-C biquadratic filters to achieve a
low current consumption. High linearity and a constant wide
bandwidth are achieved by using a new transconductance (Gm) cell.
The PGA has a voltage gain varying from 0 to 65dB, while
maintaining a constant bandwidth. A filter tuning circuit that requires
an accurate time base but no external components is presented.
With a 1-Vrms differential input and output, the filter achieves
-85dB THD and a 78dB signal-to-noise ratio. Both the filter and PGA
were implemented in a 0.18um 1P6M n-well CMOS process. They
consume 3.2mW from a 1.8V power supply and occupy an area of
0.19mm2.
Abstract: The aim of this study was to investigate the correlation
between Facebook involvement and internet addiction. We sampled
577 university students in Taiwan and administered a survey of
Facebook usage, Facebook involvement scale (FIS), and internet
addiction scale. The FIS comprises three factors (salience, emotional
support, and amusement). Results showed that the Facebook
involvement scale had good reliability and validity. The correlation
between Facebook involvement and internet addiction was measured
at .395. This means that a higher degree of Facebook involvement
indicates a greater degree of psychological dependency on the internet,
and a greater propensity towards social withdrawal and other negative
psychological consequences associated with internet addiction.
Besides, the correlations between three factors of FIS (salience,
emotional support, and amusement) and internet addiction ranged
from .313-372, indicating that these neither of these factors (salience,
emotional support, and amusement) is more effective than the others in
predicting internet dependency.
Abstract: Personal computers draw non-sinusoidal current
with odd harmonics more significantly. Power Quality of
distribution networks is severely affected due to the flow of these
generated harmonics during the operation of electronic loads. In
this paper, mathematical modeling of odd harmonics in current like
3rd, 5th, 7th and 9th influencing the power quality has been presented.
Live signals have been captured with the help of power quality
analyzer for analysis purpose. The interesting feature is that Total
Harmonic Distortion (THD) in current decreases with the increase
of nonlinear loads has been verified theoretically. The results
obtained using mathematical expressions have been compared with
the practical results and exciting results have been found.
Abstract: This paper presents the mathematical model and
control strategy on DQ frame of shunt active power filter. The
structure of the shunt active power filter is the voltage source inverter
(VSI). The pulse width modulation (PWM) with PI controller is used
in the paper. The concept of DQ frame to apply with the shunt active
power filter is described. Moreover, the detail of the PI controller
design for two current loops and one voltage loop are fully explained.
The DQ axis with Fourier (DQF) method is applied to calculate the
reference currents on DQ frame. The simulation results show that the
control strategy and the design method presented in the paper can
provide the good performance of the shunt active power filter.
Moreover, the %THD of the source currents after compensation can
follow the IEEE Std.519-1992.
Abstract: The range of the output power is a very important and evident limitation of two-level inverters. In order to overcome this disadvantage, multilevel inverters are introduced. Recently, Cascade H-Bridge inverters have emerged as one of the popular converter topologies used in numerous industrial applications. The modulation switching strategies such as phase shifted carrier based Pulse Width Modulation (PWM) technique and Stair case modulation with Selective Harmonic Elimination (SHE) PWM technique are generally used. NR method is used to solve highly non linear transcendental equations which are formed by SHEPWM method. Generally NR method has a drawback of requiring good initial guess but in this paper a new approach is implemented for NR method with any random initial guess. A three phase CHB 11-level inverter is chosen for analysis. MATLAB/SIMULINK programming environment and harmonic profiles are compared. Finally this paper presents a method at fundamental switching frequency with least % THDV.
Abstract: The paper deals with the comparison study of
harmonic detection methods for a shunt active power filter. The
%THD and the power factor value at the PCC point after
compensation are considered for the comparison. There are three
harmonic detection methods used in the paper that are synchronous
reference frame method, synchronous detection method, and DQ axis
with Fourier method. In addition, the ideal current source is used to
represent the active power filter by assuming an infinitely fast
controller action of the active power filter. The simulation results
show that the DQ axis with Fourier method provides the minimum
%THD after compensation compared with other methods. However,
the power factor value at the PCC point after compensation is slightly
lower than that of synchronous detection method.
Abstract: Unlike its conventional counterpart, Islamic principles
forbid Islamic banks to take any interest-related income and thus
makes deposits from depositors as an important source of fund for its
operational and financing. Consequently, the risk of deposit
withdrawal by depositors is an important aspect that should be wellmanaged
in Islamic banking. This paper aims to investigate factors
that influence depositors- withdrawal behavior in Islamic banks,
particularly in Malaysia, using the framework of theory of reasoned
action. A total of 368 respondents from Klang valley are involved in
the analysis. The paper finds that all the constructs variable i.e.
normative beliefs, subjective norms, behavioral beliefs, and attitude
towards behavior are perceived to be distinct by the respondents. In
addition, the structural equation model is able to verify the structural
relationships between subjective norms, attitude towards behavior
and behavioral intention. Subjective norms gives more influence to
depositors- decision on deposit withdrawal compared to attitude
towards behavior.
Abstract: Automobile Industry has great importance in the
Spanish economy (8,7 % of the active Spanish population is
employed in this sector).The above mentioned sector has been one of
the principal sectors affected by the current economic crisis,
consistently, the budgets in advertising have been severely limited
(46,9 % less in the period of reference), these needs of reduction
have originated a substantial change in the advertising strategy (from
2007 the increase of the advertising investment in Internet is 251,6
%), and increase profitability. The growing use of social media by
consumers therefore makes online consumer conversations an
attractive additional format for Automobile firms to promote
products at a lower cost. This research analyzes the relation between
the activity in Social Media and the design in the car industry,
looking for relations between strategies of design based on Social
Media and sales and a channel of information for companies to know
what the consumer preferences. For this ongoing research we used a
longitudinal withdrawal of information has been used using
information of panel. Managerial and research implications of the
finding are discussed.
Abstract: Most electrical distribution systems are incurring large
losses as the loads are wide spread, inadequate reactive power
compensation facilities and their improper control. A typical static
VAR compensator consists of capacitor bank in binary sequential
steps operated in conjunction with a thyristor controlled reactor of the
smallest step size. This SVC facilitates stepless control of reactive
power closely matching with load requirements so as to maintain
power factor nearer to unity. This type of SVC-s requiring a
appropriately controlled TCR. This paper deals with an air cored
reactor suitable for distribution transformer of 3phase, 50Hz, Dy11,
11KV/433V, 125 KVA capacity. Air cored reactors are designed,
built, tested and operated in conjunction with capacitor bank in five
binary sequential steps. It is established how the delta connected TCR
minimizes the harmonic components and the operating range for
various electrical quantities as a function of firing angle is
investigated. In particular firing angle v/s line & phase currents, D.C.
components, THD-s, active and reactive powers, odd and even triplen
harmonics, dominant characteristic harmonics are all investigated and
range of firing angle is fixed for satisfactory operation. The harmonic
spectra for phase and line quantities at specified firing angles are
given. In case the TCR is operated within the bound specified in this
paper established through simulation studies are yielding the best
possible operating condition particularly free from all dominant
harmonics.