Abstract: The present paper is an experimental investigation of
roughness effects on nucleate pool boiling of refrigerant R113 on
horizontal circular copper surfaces. The copper samples were treated
by different sand paper grit sizes to achieve different surface
roughness. The average surface roughness of the four samples was
0.901, 0.735, 0.65, and 0.09, respectively. The experiments were
performed in the heat flux range of 8 to 200kW/m2. The heat transfer
coefficient was calculated by measuring wall superheat of the
samples and the input heat flux. The results show significant
improvement of heat transfer coefficient as the surface roughness is
increased. It is found that the heat transfer coefficient of the sample
with Ra=0.901 is 3.4, 10.5, and 38.5% higher in comparison with
surfaces with Ra of 0.735, 0.65, and 0.09 at heat flux of 170 kW/m2.
Moreover, the results are compared with literature data and the well
known Cooper correlation.
Abstract: Titanium oxide films with different morphologies have for the first time been fabricated through hydrothermal reactions between a titanium substrate and iodine powder in water or ethanol. SEM revealed that iodine supported titanium (Ti-I2) surface shows different morphologies with variable treatment conditions. The mean surface roughness (Ra) was increased in the different groups. Use of surfactant has a role to increase the roughness of the film. The surface roughness was in the range of 0.15 μm-0.42 μm. Furthermore, the electrochemical examinations showed that the Ti-I2 surface fabricated in alcoholic medium has high corrosion resistance than in aqueous medium.
Abstract: Deep cold rolling (DCR) is a cold working process, which easily produces a smooth and work-hardened surface by plastic deformation of surface irregularities. In the present study, the influence of main deep cold rolling process parameters on the surface roughness and the hardness of AISI 4140 steel were studied by using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in terms of identifying the predominant factor amongst the selected parameters, their order of significance and setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. It was found that the ball diameter, rolling force, initial surface roughness and number of tool passes are the most pronounced parameters, which have great effects on the work piece-s surface during the deep cold rolling process. A simple, inexpensive and newly developed DCR tool, with interchangeable collet for using different ball diameters, was used throughout the experimental work presented in this paper.
Abstract: The impact force of a rockfall is mainly determined by
its moving behavior and velocity, which are contingent on the rock
shape, slope gradient, height, and surface roughness of the moving
path. It is essential to precisely calculate the moving path of the
rockfall in order to effectively minimize and prevent damages caused
by the rockfall. By applying the Colorado Rockfall Simulation
Program (CRSP) program as the analysis tool, this research studies the
influence of three shapes of rock (spherical, cylindrical and discoidal)
and surface roughness on the moving path of a single rockfall. As
revealed in the analysis, in addition to the slope gradient, the geometry
of the falling rock and joint roughness coefficient ( JRC ) of the slope
are the main factors affecting the moving behavior of a rockfall. On a
single flat slope, both the rock-s bounce height and moving velocity
increase as the surface gradient increases, with a critical gradient value
of 1:m = 1 . Bouncing behavior and faster moving velocity occur more
easily when the rock geometry is more oval. A flat piece tends to cause
sliding behavior and is easily influenced by the change of surface
undulation. When JRC
Abstract: Laser engraving is a manufacturing method for those applications where previously Electrical Discharge Machining (EDM) was the only choice. Laser engraving technology removes material layer-by-layer and the thickness of layers is usually in the range of few microns. The aim of the present work is to investigate the influence of the process parameters on the surface quality when machined by laser engraving. The examined parameters were: the pulse frequency, the beam speed and the layer thickness. The surface quality was determined by the surface roughness for every set of parameters. Experimental results on Al7075 material showed that the surface roughness strictly depends on the process parameters used.
Abstract: This paper presents an approach for the determination of the optimal cutting parameters (spindle speed, feed rate, depth of cut and engagement) leading to minimum surface roughness in face milling of high silicon stainless steel by coupling neural network (NN) and Electromagnetism-like Algorithm (EM). In this regard, the advantages of statistical experimental design technique, experimental measurements, artificial neural network, and Electromagnetism-like optimization method are exploited in an integrated manner. To this end, numerous experiments on this stainless steel were conducted to obtain surface roughness values. A predictive model for surface roughness is created by using a back propogation neural network, then the optimization problem was solved by using EM optimization. Additional experiments were performed to validate optimum surface roughness value predicted by EM algorithm. It is clearly seen that a good agreement is observed between the predicted values by EM coupled with feed forward neural network and experimental measurements. The obtained results show that the EM algorithm coupled with back propogation neural network is an efficient and accurate method in approaching the global minimum of surface roughness in face milling.
Abstract: This paper investigates the influence of various
parameters on the behaviour of water droplets on polymeric surfaces
under high electric fields. An inclined plane test was carried out to
understand the droplet behaviour in strong electric field. Parameters
such as water droplet conductivity, droplet volume, polymeric
surface roughness and droplet positioning with respect to the
electrodes were studied. The flashover voltage is affected by all
aforementioned parameters. The droplet positioning is in some cases
more vital than the droplet volume. Surface damages were analysed
using Scanning Electron Microscopy (SEM) studies and by Energy
dispersive X-ray Analysis (EDAX). It is observes that magnitude of
discharge have direct influence on amount of surface da
Abstract: Greenhouse gases (GHG) emissions impose major
threat to global warming potential (GWP). Unfortunately
manufacturing sector is one of the major sources that contribute
towards the rapid increase in greenhouse gases (GHG) emissions. In
manufacturing sector electric power consumption is the major driver
that influences CO2 emission. Titanium alloys are widely utilized in
aerospace, automotive and petrochemical sectors because of their
high strength to weight ratio and corrosion resistance. Titanium
alloys are termed as difficult to cut materials because of their poor
machinability rating. The present study analyzes energy consumption
during cutting with reference to material removal rate (MRR).
Surface roughness was also measured in order to optimize energy
consumption.
Abstract: Concerning the measurement of friction properties of
textiles and fabrics using Kawabata Evaluation System (KES), whose
output is constrained to the surface friction factor of fabric, and no
other data would be generated; this research has been conducted to
gain information about surface roughness regarding its surface
friction factor. To assess roughness properties of light nonwovens, a
3-dimensional model of a surface has been simulated with regular
sinuous waves through it as an ideal surface. A new factor was
defined, namely Surface Roughness Factor, through comparing
roughness properties of simulated surface and real specimens. The
relation between the proposed factor and friction factor of specimens
has been analyzed by regression, and results showed a meaningful
correlation between them. It can be inferred that the new presented
factor can be used as an acceptable criterion for evaluating the
roughness properties of light nonwoven fabrics.
Abstract: This paper presents a study of the Taguchi design
application to optimize surface quality in damper inserted end milling
operation. Maintaining good surface quality usually involves
additional manufacturing cost or loss of productivity. The Taguchi
design is an efficient and effective experimental method in which a
response variable can be optimized, given various factors, using
fewer resources than a factorial design. This Study included spindle
speed, feed rate, and depth of cut as control factors, usage of different
tools in the same specification, which introduced tool condition and
dimensional variability. An orthogonal array of L9(3^4)was used;
ANOVA analyses were carried out to identify the significant factors
affecting surface roughness, and the optimal cutting combination was
determined by seeking the best surface roughness (response) and
signal-to-noise ratio. Finally, confirmation tests verified that the
Taguchi design was successful in optimizing milling parameters for
surface roughness.
Abstract: In present work, prediction the effect of nose radius, rz (mm) on the equivalent strain (PEEQ) and surface finish during the machining of titanium alloy (Ti-6Al-4V) through orthogonal cutting process. The results were performed at several of the nose radiuses, rz (mm) while the cutting speed, vc (m/min), feed rate, f (mm/tooth) and depth of cut, d (mm) were remained constant. The equivalent plastic strain (PEEQ) was estimated by using finite element modeling (FEM) and applied through ABAQUS/EXPLICIT software. The simulation results led to conclude that the equivalent plastic strain (PEEQ) was increased and surface roughness (Ra) decreased when increasing nose radius, rz (mm) during the machining of titanium alloy (Ti–6Al–4V) in dry cutting conditions.
Abstract: Deciding the numerous parameters involved in
designing a competent artificial neural network is a complicated task.
The existence of several options for selecting an appropriate
architecture for neural network adds to this complexity, especially
when different applications of heterogeneous natures are concerned.
Two completely different applications in engineering and medical
science were selected in the present study including prediction of
workpiece's surface roughness in ultrasonic-vibration assisted turning
and papilloma viruses oncogenicity. Several neural network
architectures with different parameters were developed for each
application and the results were compared. It was illustrated in this
paper that some applications such as the first one mentioned above
are apt to be modeled by a single network with sufficient accuracy,
whereas others such as the second application can be best modeled
by different expert networks for different ranges of output.
Development of knowledge about the essentials of neural networks
for different applications is regarded as the cornerstone of
multidisciplinary network design programs to be developed as a
means of reducing inconsistencies and the burden of the user
intervention.
Abstract: In this research, Response Surface Methodology (RSM) is used to investigate the effect of four controllable input variables namely: discharge current, pulse duration, pulse off time and applied voltage Surface Roughness (SR) of on Electrical Discharge Machined surface. To study the proposed second-order polynomial model for SR, a Central Composite Design (CCD) is used to estimation the model coefficients of the four input factors, which are alleged to influence the SR in Electrical Discharge Machining (EDM) process. Experiments were conducted on AISI D2 tool steel with copper electrode. The response is modeled using RSM on experimental data. The significant coefficients are obtained by performing Analysis of Variance (ANOVA) at 5% level of significance. It is found that discharge current, pulse duration, and pulse off time and few of their interactions have significant effect on the SR. The model sufficiency is very satisfactory as the Coefficient of Determination (R2) is found to be 91.7% and adjusted R2-statistic (R2 adj ) 89.6%.
Abstract: Inconel 718, a nickel based super-alloy is an
extensively used alloy, accounting for about 50% by weight of
materials used in an aerospace engine, mainly in the gas turbine
compartment. This is owing to their outstanding strength and
oxidation resistance at elevated temperatures in excess of 5500 C.
Machining is a requisite operation in the aircraft industries for the
manufacture of the components especially for gas turbines. This
paper is concerned with optimization of the surface roughness when
turning Inconel 718 with cermet inserts. Optimization of turning
operation is very useful to reduce cost and time for machining. The
approach is based on Response Surface Method (RSM). In this work,
second-order quadratic models are developed for surface roughness,
considering the cutting speed, feed rate and depth of cut as the cutting
parameters, using central composite design. The developed models
are used to determine the optimum machining parameters. These
optimized machining parameters are validated experimentally, and it
is observed that the response values are in reasonable agreement with
the predicted values.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: Response surface methodology with Box–Benhken (BB) design of experiment approach has been utilized to study the mechanism of interface slip damping in layered and jointed tack welded beams with varying surface roughness. The design utilizes the initial amplitude of excitation, tack length and surface roughness at the interfaces to develop the model for the logarithmic damping decrement of the layered and jointed welded structures. Statistically designed experiments have been performed to estimate the coefficients in the mathematical model, predict the response, and check the adequacy of the model. Comparison of predicted and experimental response values outside the design conditions have shown good correspondence, implying that empirical model derived from response surface approach can be effectively used to describe the mechanism of interface slip damping in layered and jointed tack welded structures.
Abstract: FW4 is a newly developed hot die material widely
used in Forging Dies manufacturing. The right selection of the
machining conditions is one of the most important aspects to take
into consideration in the Electrical Discharge Machining (EDM) of
FW4. In this paper an attempt has been made to develop
mathematical models for relating the Material Removal Rate (MRR),
Tool Wear Ratio (TWR) and surface roughness (Ra) to machining
parameters (current, pulse-on time and voltage). Furthermore, a study
was carried out to analyze the effects of machining parameters in
respect of listed technological characteristics. The results of analysis
of variance (ANOVA) indicate that the proposed mathematical
models, can adequately describe the performance within the limits of
the factors being studied.
Abstract: In this paper, the wear of high speed steel hobs during
hobbing has been studied. The wear mechanisms are strongly
influenced by the choice of cutting speed. At moderate and high
cutting speeds three major wear mechanisms were identified:
abrasion, mild adhesive and severe adhesive. The microstructure and
wear behavior of two high speed steel grades (M2 and ASP30) has
been compared. In contrast, a variation in chemical composition or
microstructure of HSS tool material generally did not change the
dominant wear mechanism. However, the tool material properties
determine the resistance against the operating wear mechanism and
consequently the tool life. The metallographic analysis and wear
measurement at the tip of hob teeth included scanning electron
microscopy and stereoscope microscopy. Roughness profilometery is
used for measuring the gear surface roughness.
Abstract: This paper presents an advance in monitoring and
process control of surface roughness in CNC machine for the turning
and milling processes. An integration of the in-process monitoring
and process control of the surface roughness is proposed and
developed during the machining process by using the cutting force
ratio. The previously developed surface roughness models for turning
and milling processes of the author are adopted to predict the inprocess
surface roughness, which consist of the cutting speed, the
feed rate, the tool nose radius, the depth of cut, the rake angle, and
the cutting force ratio. The cutting force ratios obtained from the
turning and the milling are utilized to estimate the in-process surface
roughness. The dynamometers are installed on the tool turret of CNC
turning machine and the table of 5-axis machining center to monitor
the cutting forces. The in-process control of the surface roughness
has been developed and proposed to control the predicted surface
roughness. It has been proved by the cutting tests that the proposed
integration system of the in-process monitoring and the process
control can be used to check the surface roughness during the cutting
by utilizing the cutting force ratio.
Abstract: The previous study of new metal gasket that contact
width and contact stress an important design parameter for optimizing
metal gasket performance. The optimum design based on an elastic
and plastic contact stress was founded. However, the influence of
flange surface roughness had not been investigated thoroughly. The
flange has many kinds of surface roughness. In this study, we
conducted a gasket model include a flange surface roughness effect. A
finite element method was employed to develop simulation solution. A
uniform quadratic mesh used for meshing the gasket material and a
gradually quadrilateral mesh used for meshing the flange. The gasket
model was simulated by using two simulation stages which is forming
and tightening simulation. A simulation result shows that a smoother
of surface roughness has higher slope for force per unit length. This
mean a squeezed against between flange and gasket will be strong. The
slope of force per unit length for gasket 400-MPa mode was higher
than the gasket 0-MPa mode.