Abstract: Composite pins of rubber dust collected from tyre
retreading centres of trucks, cars and buses etc.and epoxy with
weight percentages of 10. 15, and 20 % of rubber (weight fractions of
9, 13 and 17 % respectively) have been prepared in house with the
help of a split wooden mould. The pins were tested in a pin-on-disc
wear monitor to determine the co-efficient of friction and weight
losses with varying speeds, loads and time. The wear volume and
wear rates have also been found out for all these three specimens.. It
is observed that all the specimens have exhibited very low coefficient
of friction and low wear rates under dry sliding condition. Out of the
above three samples tested, the specimen with 10 % rubber dust by
weight has shown lowest wear rates. However a peculiar result i.e
decreasing trend has been obtained with 20% reinforcement of rubber
in epoxy while rubbed against steel at varying speeds. This might
have occurred due to high surface finish of the disc and formation of
a thin transfer layer from the composite
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: Traditional wind tunnel models are meticulously machined from metal in a process that can take several months. While very precise, the manufacturing process is too slow to assess a new design's feasibility quickly. Rapid prototyping technology makes this concurrent study of air vehicle concepts via computer simulation and in the wind tunnel possible. This paper described the Affects layer thickness models product with rapid prototyping on Aerodynamic Coefficients for Constructed wind tunnel testing models. Three models were evaluated. The first model was a 0.05mm layer thickness and Horizontal plane 0.1μm (Ra) second model was a 0.125mm layer thickness and Horizontal plane 0.22μm (Ra) third model was a 0.15mm layer thickness and Horizontal plane 4.6μm (Ra). These models were fabricated from somos 18420 by a stereolithography (SLA). A wing-body-tail configuration was chosen for the actual study. Testing covered the Mach range of Mach 0.3 to Mach 0.9 at an angle-of-attack range of -2° to +12° at zero sideslip. Coefficients of normal force, axial force, pitching moment, and lift over drag are shown at each of these Mach numbers. Results from this study show that layer thickness does have an effect on the aerodynamic characteristics in general; the data differ between the three models by fewer than 5%. The layer thickness does have more effect on the aerodynamic characteristics when Mach number is decreased and had most effect on the aerodynamic characteristics of axial force and its derivative coefficients.
Abstract: This paper describes a combined mathematicalgraphical
approach for optimum tool path planning in order to
improve machining efficiency. A methodology has been used that
stabilizes machining operations by adjusting material removal rate in
pocket milling operations while keeping cutting forces within limits.
This increases the life of cutting tool and reduces the risk of tool
breakage, machining vibration, and chatter. Case studies reveal the
fact that application of this approach could result in a slight increase
of machining time, however, a considerable reduction of tooling cost,
machining vibration, noise and chatter can be achieved in addition to
producing a better surface finish.
Abstract: Studies have shown that the SnAgCu solder family has been widely used as a replacement for conventional Sn-Pb solders. An attractive approach is by introducing alloying additives (rare earth elements (RE), Zn, Co, Fe, Ni, Sb) into the SnAgCu solder, which helps in refining the microstructure also improving the mechanical and wetting properties of the solder. The present work focuses on the effect of additions of 0.5% Ce and Fe into Sn-3.0Ag-0.5Cu solder, in attempt to reduce the intermetallic compound (IMC) growth and reflow properties of the solder on Cu and Ni (P) surface finish, as well as effects thermal aging on the formation of intermetallic compound (IMC) on different surface finish. Excessive intermetallic compound growth may effect the interface and solder joint due to the brittle nature of the intermetallic compounds. Thus, by introducing alloying elements, IMC layer thickness can be decrease, resulting in better joint and solder reliability.
Abstract: A mathematical model for determining the overall efficiency
of a multistage tractor gearbox including all gear, lubricant,
surface finish related parameters and operating conditions is
presented. Sliding friction, rolling friction and windage losses were
considered as the main sources of power loss in the gearing system. A
computer code in FORTRAN was developed to simulate the model.
Sliding friction contributes about 98% of the total power loss for
gear trains operating at relatively low speeds (less than 2000 rpm
input speed). Rolling frictional losses decrease with increased load
while windage losses are only significant for gears running at very
high speeds (greater than 3000 rpm). The results also showed that the
overall efficiency varies over the path of contact of the gear meshes
ranging between 94% to 99.5%.
Abstract: Greenhouse gases (GHG) emissions impose major
threat to global warming potential (GWP). Unfortunately
manufacturing sector is one of the major sources that contribute
towards the rapid increase in greenhouse gases (GHG) emissions. In
manufacturing sector electric power consumption is the major driver
that influences CO2 emission. Titanium alloys are widely utilized in
aerospace, automotive and petrochemical sectors because of their
high strength to weight ratio and corrosion resistance. Titanium
alloys are termed as difficult to cut materials because of their poor
machinability rating. The present study analyzes energy consumption
during cutting with reference to material removal rate (MRR).
Surface roughness was also measured in order to optimize energy
consumption.
Abstract: In present work, prediction the effect of nose radius, rz (mm) on the equivalent strain (PEEQ) and surface finish during the machining of titanium alloy (Ti-6Al-4V) through orthogonal cutting process. The results were performed at several of the nose radiuses, rz (mm) while the cutting speed, vc (m/min), feed rate, f (mm/tooth) and depth of cut, d (mm) were remained constant. The equivalent plastic strain (PEEQ) was estimated by using finite element modeling (FEM) and applied through ABAQUS/EXPLICIT software. The simulation results led to conclude that the equivalent plastic strain (PEEQ) was increased and surface roughness (Ra) decreased when increasing nose radius, rz (mm) during the machining of titanium alloy (Ti–6Al–4V) in dry cutting conditions.
Abstract: The present work analyses different parameters of pressure die casting to minimize the casting defects. Pressure diecasting is usually applied for casting of aluminium alloys. Good surface finish with required tolerances and dimensional accuracy can be achieved by optimization of controllable process parameters such as solidification time, molten temperature, filling time, injection pressure and plunger velocity. Moreover, by selection of optimum process parameters the pressure die casting defects such as porosity, insufficient spread of molten material, flash etc. are also minimized. Therefore, a pressure die casting component, carburetor housing of aluminium alloy (Al2Si2O5) has been considered. The effects of selected process parameters on casting defects and subsequent setting of parameters with the levels have been accomplished by Taguchi-s parameter design approach. The experiments have been performed as per the combination of levels of different process parameters suggested by L18 orthogonal array. Analyses of variance have been performed for mean and signal-to-noise ratio to estimate the percent contribution of different process parameters. Confidence interval has also been estimated for 95% consistency level and three conformational experiments have been performed to validate the optimum level of different parameters. Overall 2.352% reduction in defects has been observed with the help of suggested optimum process parameters.
Abstract: The aim of this research is to evaluate surface
roughness and develop a multiple regression model for surface roughness as a function of cutting parameters during the turning of
flame hardened medium carbon steel with TiN-Al2O3-TiCN coated inserts. An experimental plan of work and signal-to-noise ratio (S/N)
were used to relate the influence of turning parameters to the
workpiece surface finish utilizing Taguchi methodology. The effects
of turning parameters were studied by using the analysis of variance (ANOVA) method. Evaluated parameters were feed, cutting speed,
and depth of cut. It was found that the most significant interaction among the considered turning parameters was between depth of cut and feed. The average surface roughness (Ra) resulted by TiN-Al2O3-
TiCN coated inserts was about 2.44 μm and minimum value was 0.74 μm. In addition, the regression model was able to predict values for surface roughness in comparison with experimental values within
reasonable limit.
Abstract: End milling process is one of the common metal
cutting operations used for machining parts in manufacturing
industry. It is usually performed at the final stage in manufacturing a
product and surface roughness of the produced job plays an
important role. In general, the surface roughness affects wear
resistance, ductility, tensile, fatigue strength, etc., for machined parts
and cannot be neglected in design. In the present work an
experimental investigation of end milling of aluminium alloy with
carbide tool is carried out and the effect of different cutting
parameters on the response are studied with three-dimensional
surface plots. An artificial neural network (ANN) is used to establish
the relationship between the surface roughness and the input cutting
parameters (i.e., spindle speed, feed, and depth of cut). The Matlab
ANN toolbox works on feed forward back propagation algorithm is
used for modeling purpose. 3-12-1 network structure having
minimum average prediction error found as best network architecture
for predicting surface roughness value. The network predicts surface
roughness for unseen data and found that the result/prediction is
better. For desired surface finish of the component to be produced
there are many different combination of cutting parameters are
available. The optimum cutting parameter for obtaining desired
surface finish, to maximize tool life is predicted. The methodology is
demonstrated, number of problems are solved and algorithm is coded
in Matlab®.
Abstract: TUSAT is a prospective Turkish
Communication Satellite designed for providing mainly data
communication and broadcasting services through Ku-Band
and C-Band channels. Thermal control is a vital issue in
satellite design process. Therefore, all satellite subsystems and
equipments should be maintained in the desired temperature
range from launch to end of maneuvering life. The main
function of the thermal control is to keep the equipments and
the satellite structures in a given temperature range for various
phases and operating modes of spacecraft during its lifetime.
This paper describes the thermal control design which uses
passive and active thermal control concepts. The active
thermal control is based on heaters regulated by software via
thermistors. Alternatively passive thermal control composes of
heat pipes, multilayer insulation (MLI) blankets, radiators,
paints and surface finishes maintaining temperature level of
the overall carrier components within an acceptable value.
Thermal control design is supported by thermal analysis using
thermal mathematical models (TMM).
Abstract: A novel nanofinishing process using improved ball
end magnetorheological (MR) finishing tool was developed for finishing of flat as well as 3D surfaces of ferromagnetic and non ferromagnetic workpieces. In this process a magnetically controlled
ball end of smart MR polishing fluid is generated at the tip surface of
the tool which is used as a finishing medium and it is guided to
follow the surface to be finished through computer controlled 3-axes
motion controller. The experiments were performed on ferromagnetic
workpiece surface in the developed MR finishing setup to study the effect of finishing time on final surface roughness. The performance
of present finishing process on final finished surface roughness was studied. The surface morphology was observed under scanning
electron microscopy and atomic force microscope. The final surface finish was obtained as low as 19.7 nm from the initial surface
roughness of 142.9 nm. The outcome of newly developed finishing process can be found useful in its applications in aerospace,
automotive, dies and molds manufacturing industries, semiconductor and optics machining etc.
Abstract: The machining of Carbon Fiber Reinforced Plastics
has come to constitute a significant challenge for many fields of
industry. The resulting surface finish of machined parts is of primary
concern for several reasons, including contact quality and impact on
the assembly. Therefore, the characterization and prediction of
roughness based on machining parameters are crucial for costeffective
operations. In this study, a PCD tool comprised of two
straight flutes was used to trim 32-ply carbon fiber laminates in a bid
to analyze the effects of the feed rate and the cutting speed on the
surface roughness. The results show that while the speed has but a
slight impact on the surface finish, the feed rate for its part affects it
strongly. A detailed study was also conducted on the effect of fiber
orientation on surface roughness, for quasi-isotropic laminates used
in aerospace. The resulting roughness profiles for the four-ply
orientation lay-up were compared, and it was found that fiber angle is
a critical parameter relating to surface roughness. One of the four
orientations studied led to very poor surface finishes, and
characteristic roughness profiles were identified and found to only
relate to the ply orientations of multilayer carbon fiber laminates.
Abstract: In this paper an attempt has been made to correlate the usefulness of electrodes made through powder metallurgy (PM) in comparison with conventional copper electrode during electric discharge machining. Experimental results are presented on electric discharge machining of AISI D2 steel in kerosene with copper tungsten (30% Cu and 70% W) tool electrode made through powder metallurgy (PM) technique and Cu electrode. An L18 (21 37) orthogonal array of Taguchi methodology was used to identify the effect of process input factors (viz. current, duty cycle and flushing pressure) on the output factors {viz. material removal rate (MRR) and surface roughness (SR)}. It was found that CuW electrode (made through PM) gives high surface finish where as the Cu electrode is better for higher material removal rate.