Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: A real time image-guided electroplating system is
proposed in this paper. Unlike previous electroplating systems, instead
of using the intermittent mode to electroplate 500um long copper
specimen, a CCD camera and a motion controller are used to adjust
anode-cathode distance to obtain better results. Since the image of the
gap distance is highly deteriorated due to complex chemical-electrical
operation inside the electrolyte, to determine the gap distance, an
image processing algorithm is developed and mainly based on the
entropy and energy values. In addition, the color and incidence
direction of light source are also discussed to help the image process in
this paper. From the experiment results, the specimens created by the
proposed system show better structure, better uniformity and better
finishing surface compared to those by previous intermittent
electroplating setup.
Abstract: The blood ducts must be occluded to avoid loss of
blood from vessels in laparoscopic surgeries. This paper presents a
locking mechanism to be used in a ligation laparoscopic procedure
(LigLAP I), as an alternative solution for a stapling procedure.
Currently, stapling devices are being used to occlude vessels. Using
these devices may result in some problems, including injury of bile
duct, taking up a great deal of space behind the vessel, and bile leak.
In this new procedure, a two-layer suture occludes a vessel. A
locking mechanism is also required to hold the suture. Since there is
a limited space at the device tip, a Shape Memory Alloy (SMA)
actuator is used in this mechanism. Suitability for cleanroom
applications, small size, and silent performance are among the
advantages of SMA actuators in biomedical applications. An
experimental study is conducted to examine the function of the
locking mechanism. To set up the experiment, a prototype of a
locking mechanism is built using nitinol, which is a nickel-titanium
shape memory alloy. The locking mechanism successfully locks a
polymer suture for all runs of the experiment. In addition, the effects
of various surface materials on the applied pulling forces are studied.
Various materials are mounted at the mechanism tip to compare the
maximum pulling forces applied to the suture for each material. The
results show that the various surface materials on the device tip
provide large differences in the applied pulling forces.
Abstract: In this study, a low temperature sensor highly selective to CO in presence of methane is fabricated by using 4 nm SnO2 quantum dots (QDs) prepared by sonication assisted precipitation. SnCl4 aqueous solution was precipitated by ammonia under sonication, which continued for 2 h. A part of the sample was then dried and calcined at 400°C for 1.5 h and characterized by XRD and BET. The average particle size and the specific surface area of the SnO2 QDs as well as their sensing properties were compared with the SnO2 nano-particles which were prepared by conventional sol-gel method. The BET surface area of sonochemically as-prepared product and the one calcined at 400°C after 1.5 hr are 257 m2/gr and 212 m2/gr respectively while the specific surface area for SnO2 nanoparticles prepared by conventional sol-gel method is about 80m2/gr. XRD spectra revealed pure crystalline phase of SnO2 is formed for both as-prepared and calcined samples of SnO2 QDs. However, for the sample prepared by sol-gel method and calcined at 400°C SnO crystals are detected along with those of SnO2. Quantum dots of SnO2 show exceedingly high sensitivity to CO with different concentrations of 100, 300 and 1000 ppm in whole range of temperature (25- 350°C). At 50°C a sensitivity of 27 was obtained for 1000 ppm CO, which increases to a maximum of 147 when the temperature rises to 225°C and then drops off while the maximum sensitivity for the SnO2 sample prepared by the sol-gel method was obtained at 300°C with the amount of 47.2. At the same time no sensitivity to methane is observed in whole range of temperatures for SnO2 QDs. The response and recovery times of the sensor sharply decreases with temperature, while the high selectivity to CO does not deteriorate.
Abstract: The aim of this paper is to study the oblique
stagnation point flow on vertical plate with uniform surface heat flux
in presence of magnetic field. Using Stream function, partial
differential equations corresponding to the momentum and energy
equations are converted into non-linear ordinary differential
equations. Numerical solutions of these equations are obtained using
Runge-Kutta Fehlberg method with the help of shooting technique.
In the present work the effects of striking angle, magnetic field
parameter, Grashoff number, the Prandtl number on velocity and heat
transfer characteristics have been discussed. Effect of above
mentioned parameter on the position of stagnation point are also
studied.
Abstract: Automatic methods of detecting changes through
satellite imaging are the object of growing interest, especially
beca²use of numerous applications linked to analysis of the Earth’s
surface or the environment (monitoring vegetation, updating maps,
risk management, etc...). This work implemented spatial analysis
techniques by using images with different spatial and spectral
resolutions on different dates. The work was based on the principle
of control charts in order to set the upper and lower limits beyond
which a change would be noted. Later, the a contrario approach was
used. This was done by testing different thresholds for which the
difference calculated between two pixels was significant. Finally,
labeled images were considered, giving a particularly low difference
which meant that the number of “false changes” could be estimated
according to a given limit.
Abstract: In this paper, we propose a geometric modeling of
illumination on the patterned image containing etching transistor. This
image is captured by a commercial camera during the inspection of
a TFT-LCD panel. Inspection of defect is an important process in the
production of LCD panel, but the regional difference in brightness,
which has a negative effect on the inspection, is due to the uneven
illumination environment. In order to solve this problem, we present
a geometric modeling of illumination consisting of an interpolation
using the least squares method and 3D modeling using bezier surface.
Our computational time, by using the sampling method, is shorter
than the previous methods. Moreover, it can be further used to correct
brightness in every patterned image.
Abstract: The present work was conducted for Arsenic (III)
removal, which one of the most poisonous groundwater pollutants, by
synthetic nano size zerovalent iron (nZVI). Batch experiments were
performed to investigate the influence of As (III), nZVI
concentration, pH of solution and contact time on the efficiency of As
(III) removal. nZVI was synthesized by reduction of ferric chloride
by sodium borohydrid. SEM and XRD were used to determine
particle size and characterization of produced nanoparticles. Up to
99.9% removal efficiency for arsenic (III) was obtained by nZVI
dosage of 1 g/L at time equal to 10 min. and pH=7. It could be
concluded that the removal efficiency were enhanced with increasing
of ZVI dosage and reaction time, but decreased with increasing of
arsenic concentration and pH for nano sized ZVI. nZVI presented an
outstanding ability to remove As (III) due to not only a high surface
area and low particle size but also to high inherent activity.
Abstract: Particle detection in very noisy and low contrast images
is an active field of research in image processing. In this article, a
method is proposed for the efficient detection and sizing of subsurface
spherical particles, which is used for the processing of softly fused
Au nanoparticles. Transmission Electron Microscopy is used for
imaging the nanoparticles, and the proposed algorithm has been
tested with the two-dimensional projected TEM images obtained.
Results are compared with the data obtained by transmission optical
spectroscopy, as well as with conventional circular object detection
algorithms.
Abstract: This paper presents a low cost automatic system for
sampling the electric field in a limited area. The scanning area is a
flat surface parallel to the ground at a selected height. We discuss
in detail the hardware, software and all the arrangements involved
in the system operation. In order to show the system performance
we include a campaign of narrow band measurements with 6017
sample points in the surroundings of a cellular base station. A
commercial isotropic antenna with three orthogonal axes was used
as sampling device. The results are analyzed in terms of its space
average, standard deviation and statistical distribution.
Abstract: This paper describes the optimization of a complex
dairy farm simulation model using two quite different methods of
optimization, the Genetic algorithm (GA) and the Lipschitz
Branch-and-Bound (LBB) algorithm. These techniques have been
used to improve an agricultural system model developed by Dexcel
Limited, New Zealand, which describes a detailed representation of
pastoral dairying scenarios and contains an 8-dimensional parameter
space. The model incorporates the sub-models of pasture growth and
animal metabolism, which are themselves complex in many cases.
Each evaluation of the objective function, a composite 'Farm
Performance Index (FPI)', requires simulation of at least a one-year
period of farm operation with a daily time-step, and is therefore
computationally expensive. The problem of visualization of the
objective function (response surface) in high-dimensional spaces is
also considered in the context of the farm optimization problem.
Adaptations of the sammon mapping and parallel coordinates
visualization are described which help visualize some important
properties of the model-s output topography. From this study, it is
found that GA requires fewer function evaluations in optimization
than the LBB algorithm.
Abstract: Tread design has evolved over the years to achieve the common tread pattern used in current vehicles. However, to meet safety and comfort requirements, tread design considers more than one design factor. Tread design must consider the grip and drainage, and the manner in which to reduce rolling noise, which is one of the main factors considered by manufacturers. The main objective of this study was the application the computational fluid dynamics (CFD) technique to simulate the contact surface of the tire and ground. The results demonstrated an air-Pumping and large pressure drop effect in the process of contact surface. The results also revealed that the pressure can be used to analyze sound pressure level (SPL).
Abstract: A study was undertaken to assess the potential of an
Algal Turf Scrubber to remove nitrogen from aquaculture effluent to
reduce environmental pollution. High total ammonia nitrogen
concentrations were introduced to an Algal Turf Scrubber developed
under varying hydraulic surface loading rates of African catfish
(Clarius gariepinus) effluent in a recirculating aquaculture system.
Nutrient removal rates were not affected at total suspended solids
concentration of up to 0.04g TSS/l (P > 0.05). Nitrogen removal
rates 0.93-0.99g TAN/m²/d were recorded at very high loading rates
3.76-3.81 g TAN/m²/d. Total ammonia removal showed ½ order
kinetics between 1.6 to 2.3mg/l Total Ammonia Nitrogen
concentrations. Nitrogen removal increased with its loading, which
increased with hydraulic surface loading rate. Total Ammonia
Nitrogen removal by Algal turf scrubber was higher than reported
values for fluidized bed filters and trickling filters. The algal turf
scrubber also effectively removed nitrate thereby reducing the need
for water exchange.
Abstract: A specially designed flat plate was mounted vertically
over the axial line in the wind tunnel of the Aerospace Department of
the Pusan National University. The plate is 2 m long, 0.8 m high and 8
cm thick. The measurements were performed in velocity range from
15 to 60 m/s. A sand paper turbulizer was placed close to the plate nose
to provide fully developed turbulent boundary layer over the most part
of the plate. Strain balances were mounted in the trailing part of the
plate to measure the skin friction drag over removable insertions of
0.55×0.25m2 size. A set of the insertions was designed and
manufactured: 3mm thick polished metal surface and three compliant
surfaces. The compliant surfaces were manufactured of a silicone
rubber Silastic® S2 (Dow Corning company). To modify the
viscoelastic properties of the rubber, its composition was varied: 90%
of the rubber + 10% catalyst (standard), 92.5% + 7.5% (weak), 85% +
15% (strong). Modulus of elasticity and the loss tangent were
measured accurately for these materials in the frequency range from
40 Hz to 3 KHz using the unique proposed technique.
Abstract: In this research, a part of Aghche basin in Isfahan
province with an area about 2000 hectars, was chosen to be obtain
curve number coefficient runoff and W indicator in second Cook
method By using aerial photos 1968 and 1995, the satellite data of
the IRS in 2008. Then the process of land use changes in the period
of study and its effect on the changes of curve number (CN), W
indicator and surface runoff coefficient (C) of the basin was
investigated. These results showed that on the track of these land use
changes the weight averages curve number (CN), surface runoff
coefficient (C) and W indicator of the basin were increased to 0.92,
0.02 and 0.78 unit in the first period of study and 1.18, 0.03, 0.99
Unit in the second period of study respectively.
Abstract: Tungsten trioxide has been prepared by using P-PTA
as a precursor on alumina substrates by spin coating method.
Palladium introduced on WO3 film via electrolysis deposition by
using palladium chloride as catalytic precursor. The catalytic
precursor was introduced on the series of films with different
morphologies. X-ray diffractometry (XRD), Scanning electron
microscopy (SEM) and XPS were applied to analyze structure and
morphology of the fabricated thin films. Then we measured variation
of samples- electrical conductivity of pure and Pd added films in air
and diluted hydrogen. Addition of Pd resulted in a remarkable
improvement of the hydrogen sensing properties of WO3 by detection
of Hydrogen below 1% at room temperature. Also variation of the
electrical conductivity in the presence of diluted hydrogen revealed
that response of samples depends rather strongly on the palladium
configuration on the surface.
Abstract: In real-time networks a large number of application programs are relying on video data and heterogeneous data transmission techniques. The aim of this research is presenting a method for end-to-end vouch quality service in surface applicationlayer for sending video data in comparison form in wireless heterogeneous networks. This method tries to improve the video sending over the wireless heterogeneous networks with used techniques in surface layer, link and application. The offered method is showing a considerable improvement in quality observing by user. In addition to this, other specifications such as shortage of data load that had require to resending and limited the relation period length to require time for second data sending, help to be used the offered method in the wireless devices that have a limited energy. The presented method and the achieved improvement is simulated and presented in the NS-2 software.
Abstract: In this work, we analyze the deformation of surface
waves in shallow flows conditions, propagating in a channel of
slowly varying cross-section. Based on a singular perturbation
technique, the main purpose is to predict the motion of waves by
using a dimensionless formulation of the governing equations,
considering that the longitudinal variation of the transversal section
obey a power-law distribution. We show that the spatial distribution
of the waves in the varying cross-section is a function of a kinematic
parameter,κ , and two geometrical parameters εh
and w ε . The above
spatial behavior of the surface elevation is modeled by an ordinary
differential equation. The use of single formulas to model the varying
cross sections or transitions considered in this work can be a useful
approximation to natural or artificial geometrical configurations.
Abstract: Deoxygenation of beef fat for the production of hydrogenated biodiesel is investigated in a high pressure continuous flow fixed bed reactor over palladium-supported mesoporous titania catalyst synthesized via a combined single-step sol-gel process with surfactant-assisted templating method (SATM). The catalyst possessed a mesoporous charactheristic with high surface area and narrow pore size distribution. The main products of all Pd/TiO2 catalysts are n-heptadecane (n-C17) and n-pentadecane (n-C15) resulting from decarbonylation reaction. Pd/TiO2 catalyst synthesized via a combined single-step sol-gel process with SATM (SSSG) gave higher activity and selectivity to the desired products when compared to IWI/SG-TiO2 and IWI/P25-TiO2, respectively. SSSG catalyst gave the average conversion up to 80-90 % and 80 % for the selectivity in diesel range hydrocarbons. This result may cause by the higher surface area and the ability in dispersion of palladium ion in mesoporous of TiO2 during sol-gel process.
Abstract: Contamination of aromatic compounds in water can
cause severe long-lasting effects not only for biotic organism but also
on human health. Several alternative technologies for remediation of
polluted water have been attempted. One of these is adsorption
process of aromatic compounds by using organic modified clay
mineral. Porous structure of clay is potential properties for molecular
adsorptivity and it can be increased by immobilizing hydrophobic
structure to attract organic compounds. In this work natural
montmorillonite were modified with cetyltrimethylammonium
(CTMA+) and was evaluated for use as adsorbents of aromatic
compounds: benzene, toluene, and 2-chloro phenol in its single and
multicomponent solution by ethanol:water solvent. Preparation of
CTMA-montmorillonite was conducted by simple ion exchange
procedure and characterization was conducted by using x-day
diffraction (XRD), Fourier-transform infra red (FTIR) and gas
sorption analysis. The influence of structural modification of
montmorillonite on its adsorption capacity and adsorption affinity of
organic compound were studied. It was shown that adsorptivity of
montmorillonite was increased by modification associated with
arrangements of CTMA+ in the structure even the specific surface
area of modified montmorillonite was lower than raw
montmorillonite. Adsorption rate indicated that material has affinity
to adsorb compound by following order: benzene> toluene > 2-chloro
phenol. The adsorption isotherms of benzene and toluene showed 1st
order adsorption kinetic indicating a partition phenomenon of
compounds between the aqueous and organophilic CTMAmontmorillonite.