Abstract: This paper proposes a methodology for analysis of
the dynamic behavior of a robotic manipulator in continuous
time. Initially this system (nonlinear system) will be decomposed
into linear submodels and analyzed in the context of the Linear
and Parameter Varying (LPV) Systems. The obtained linear
submodels, which represent the local dynamic behavior of the
robotic manipulator in some operating points were grouped in
a Takagi-Sugeno fuzzy structure. The obtained fuzzy model was
analyzed and validated through analog simulation, as universal
approximator of the robotic manipulator.
Abstract: A cognitive collaborative reinforcement learning
algorithm (CCRL) that incorporates an advisor into the learning
process is developed to improve supervised learning. An autonomous
learner is enabled with a self awareness cognitive skill to decide
when to solicit instructions from the advisor. The learner can also
assess the value of advice, and accept or reject it. The method is
evaluated for robotic motion planning using simulation. Tests are
conducted for advisors with skill levels from expert to novice. The
CCRL algorithm and a combined method integrating its logic with
Clouse-s Introspection Approach, outperformed a base-line fully
autonomous learner, and demonstrated robust performance when
dealing with various advisor skill levels, learning to accept advice
received from an expert, while rejecting that of less skilled
collaborators. Although the CCRL algorithm is based on RL, it fits
other machine learning methods, since advisor-s actions are only
added to the outer layer.
Abstract: The whole work is based on possibility to use Lego Mindstorms robotics systems to reduce costs. Lego Mindstorms consists of a wide variety of hardware components necessary to simulate, programme and test of robotics systems in practice. To programme algorithm, which simulates space using the ultrasonic sensor, was used development environment supplied with kit. Software Matlab was used to render values afterwards they were measured by ultrasonic sensor. The algorithm created for this paper uses theoretical knowledge from area of signal processing. Data being processed by algorithm are collected by ultrasonic sensor that scans 2D space in front of it. Ultrasonic sensor is placed on moving arm of robot which provides horizontal moving of sensor. Vertical movement of sensor is provided by wheel drive. The robot follows map in order to get correct positioning of measured data. Based on discovered facts it is possible to consider Lego Mindstorm for low-cost and capable kit for real-time modelling.
Abstract: This work deals with the design of the robotic assembly
system for the roller clamps. The task is characterized by high speed,
high yield and safety engagement. This paper describes the design of
different parts of an automated high speed machine to assemble the
parts of roller clamps. The roller clamp robotic assembly system
performs various processes in the assembly line which include clamp
body and roller feeding, inserting the roller into the clamp body, and
dividing the rejected clamp and successfully assembled clamp into
their own tray. The electrical/electronics design of the machine is
discussed. The target is to design a cost effective, minimum
maintenance and high speed machine for the industry applications.
Abstract: Due to their high power-to-weight ratio and low cost,
pneumatic actuators are attractive for robotics and automation
applications; however, achieving fast and accurate control of their
position have been known as a complex control problem. A
methodology for obtaining high position accuracy with a linear
pneumatic actuator is presented. During experimentation with a
number of PID classical control approaches over many operations of
the pneumatic system, the need for frequent manual re-tuning of the
controller could not be eliminated. The reason for this problem is
thermal and energy losses inside the cylinder body due to the
complex friction forces developed by the piston displacements.
Although PD controllers performed very well over short periods, it
was necessary in our research project to introduce some form of
automatic gain-scheduling to achieve good long-term performance.
We chose a fuzzy logic system to do this, which proved to be an
easily designed and robust approach. Since the PD approach showed
very good behaviour in terms of position accuracy and settling time,
it was incorporated into a modified form of the 1st order Tagaki-
Sugeno fuzzy method to build an overall controller. This fuzzy gainscheduler
uses an input variable which automatically changes the PD
gain values of the controller according to the frequency of repeated
system operations. Performance of the new controller was
significantly improved and the need for manual re-tuning was
eliminated without a decrease in performance. The performance of
the controller operating with the above method is going to be tested
through a high-speed web network (GRID) for research purposes.
Abstract: Stair climbing is one of critical issues for field robots to
widen applicable areas. This paper presents optimal design on
kinematic parameters of a new robotic platform for stair climbing. The
robotic platform climbs various stairs by body flip locomotion with
caterpillar type main platform. Kinematic parameters such as platform
length, platform height, and caterpillar rotation speed are optimized to
maximize stair climbing stability. Three types of stairs are used to
simulate typical user conditions. The optimal design process is
conducted based on Taguchi methodology, and resulting parameters
with optimized objective function are presented. In near future, a
prototype is assembled for real environment testing.
Abstract: In this paper the direct kinematic model of a multiple
applications three degrees of freedom industrial manipulator, was
developed using the homogeneous transformation matrices and the
Denavit - Hartenberg parameters, likewise the inverse kinematic
model was developed using the same method, verifying that in the
workload border the inverse kinematic presents considerable errors,
therefore a genetic algorithm was implemented to optimize the model
improving greatly the efficiency of the model.
Abstract: In this project, a tele-operated anthropomorphic
robotic arm and hand is designed and built as a versatile robotic arm
system. The robot has the ability to manipulate objects such as pick
and place operations. It is also able to function by itself, in
standalone mode.
Firstly, the robotic arm is built in order to interface with a personal
computer via a serial servo controller circuit board. The circuit board
enables user to completely control the robotic arm and moreover,
enables feedbacks from user. The control circuit board uses a
powerful integrated microcontroller, a PIC (Programmable Interface
Controller). The PIC is firstly programmed using BASIC (Beginner-s
All-purpose Symbolic Instruction Code) and it is used as the 'brain'
of the robot. In addition a user friendly Graphical User Interface
(GUI) is developed as the serial servo interface software using
Microsoft-s Visual Basic 6.
The second part of the project is to use speech recognition control
on the robotic arm. A speech recognition circuit board is constructed
with onboard components such as PIC and other integrated circuits. It
replaces the computers- Graphical User Interface. The robotic arm is
able to receive instructions as spoken commands through a
microphone and perform operations with respect to the commands
such as picking and placing operations.
Abstract: This paper presents the Function Approximation
Technique (FAT) based adaptive impedance control for a robotic
finger. The force based impedance control is developed so that the
robotic finger tracks the desired force while following the reference
position trajectory, under unknown environment position and
uncertainties in finger parameters. The control strategy is divided into
two phases, which are the free and contact phases. Force error
feedback is utilized in updating the uncertain environment position
during contact phase. Computer simulations results are presented to
demonstrate the effectiveness of the proposed technique.
Abstract: Walking and sit to stand are activities carried out by
all the people many times during the day, but physical disabilities due
to age and diseases create needs of assistive devices to help elderly
people during their daily life. This study aims to study the different
types and mechanisms of the assistive devices. We will analyze the
limitations and the challenges faced by the researchers in this field.
We will introduce the Assistive Device developed at the Egypt-Japan
University of Science and Technology, named E-JUST Assistive
Device (EJAD). EJAD will be a low cost intelligent assistive device
to help elders in walking and sit-to-stand activities.
Abstract: A novel low-cost impedance control structure is
proposed for monitoring the contact force between end-effector and
environment without installing an expensive force/torque sensor.
Theoretically, the end-effector contact force can be estimated from the
superposition of each joint control torque. There have a nonlinear
matrix mapping function between each joint motor control input and
end-effector actuating force/torques vector. This new force control
structure can be implemented based on this estimated mapping matrix.
First, the robot end-effector is manipulated to specified positions, then
the force controller is actuated based on the hall sensor current
feedback of each joint motor. The model-free fuzzy sliding mode
control (FSMC) strategy is employed to design the position and force
controllers, respectively. All the hardware circuits and software
control programs are designed on an Altera Nios II embedded
development kit to constitute an embedded system structure for a
retrofitted Mitsubishi 5 DOF robot. Experimental results show that PI
and FSMC force control algorithms can achieve reasonable contact
force monitoring objective based on this hardware control structure.
Abstract: Speed estimation is one of the important and practical tasks in machine vision, Robotic and Mechatronic. the availability of high quality and inexpensive video cameras, and the increasing need for automated video analysis has generated a great deal of interest in machine vision algorithms. Numerous approaches for speed estimation have been proposed. So classification and survey of the proposed methods can be very useful. The goal of this paper is first to review and verify these methods. Then we will propose a novel algorithm to estimate the speed of moving object by using fuzzy concept. There is a direct relation between motion blur parameters and object speed. In our new approach we will use Radon transform to find direction of blurred image, and Fuzzy sets to estimate motion blur length. The most benefit of this algorithm is its robustness and precision in noisy images. Our method was tested on many images with different range of SNR and is satisfiable.
Abstract: In this paper, we have proposed a low cost optimized solution for the movement of a three-arm manipulator using Genetic Algorithm (GA) and Analytical Hierarchy Process (AHP). A scheme is given for optimizing the movement of robotic arm with the help of Genetic Algorithm so that the minimum energy consumption criteria can be achieved. As compared to Direct Kinematics, Inverse Kinematics evolved two solutions out of which the best-fit solution is selected with the help of Genetic Algorithm and is kept in search space for future use. The Inverse Kinematics, Fitness Value evaluation and Binary Encoding like tasks are simulated and tested. Although, three factors viz. Movement, Friction and Least Settling Time (or Min. Vibration) are used for finding the Fitness Function / Fitness Values, however some more factors can also be considered.
Abstract: A new robust nonlinear control scheme of a manipulator is proposed in this paper which is robust against modeling errors and unknown disturbances. It is based on the principle of variable structure control, with sliding mode control (SMC) method. The variable structure control method is a robust method that appears to be well suited for robotic manipulators because it requers only bounds on the robotic arm parameters. But there is no single systematic procedure that is guaranteed to produce a suitable control law. Also, to reduce chattring of the control signal, we replaced the sgn function in the control law by a continuous approximation such as tangant function. We can compute the maximum load with regard to applied torque into joints. The effectivness of the proposed approach has been evaluated analitically demonstrated through computer simulations for the cases of variable load and robot arm parameters.
Abstract: In this paper, a simple active contour based visual
tracking algorithm is presented for outdoor AGV application which is
currently under development at the USM robotic research group
(URRG) lab. The presented algorithm is computationally low cost
and able to track road boundaries in an image sequence and can
easily be implemented on available low cost hardware. The proposed
algorithm used an active shape modeling using the B-spline
deformable template and recursive curve fitting method to track the
current orientation of the road.
Abstract: To improve HSE standards, oil and gas industries are
interested in using remotely controlled and autonomous robots instead
of human workers on offshore platforms. In addition to earlier reason
this strategy would increase potential revenue, efficient usage of
work experts and even would allow operations in more remote areas.
This article is the presentation of a custom climbing robot, called
Walloid, designed for offshore platform topside automation. This 4
arms climbing robot with grippers is an ongoing project at University
of Oslo.
Abstract: Deployment of pneumatic muscles in various
industrial applications is still in its early days, considering the relative
newness of these components. The field of robotics holds particular
future potential for pneumatic muscles, especially in view of their
specific behaviour known as compliance. The paper presents and
discusses an innovative constructive solution for a gripper system
mountable on an industrial robot, based on actuation by a linear
pneumatic muscle and transmission of motion by gear and rack
mechanism. The structural, operational and constructive models of
the new gripper are presented, along with some of the experimental
results obtained subsequently to the testing of a prototype. Further
presented are two control variants of the gripper system, one by
means of a 3/2-way fast-switching solenoid valve, the other by means
of a proportional pressure regulator. Advantages and disadvantages
are discussed for both variants.
Abstract: The research on two-wheeled inverted pendulum (TWIP) mobile robots or commonly known as balancing robots have gained momentum over the last decade in a number of robotic laboratories around the world. This paper describes the hardware design of such a robot. The objective of the design is to develop a TWIP mobile robot as well as MATLAB interfacing configuration to be used as flexible platform comprises of embedded unstable linear plant intended for research and teaching purposes. Issues such as selection of actuators and sensors, signal processing units, MATLAB Real Time Workshop coding, modeling and control scheme will be addressed and discussed. The system is then tested using a wellknown state feedback controller to verify its functionality.
Abstract: The project describes the modeling of various
architectures mechatronics specifically morphologies of robots in an educational environment. Each structure developed by students of
pre-school, primary and secondary was created using the concept of
reverse engineering in a constructivist environment, to later be integrated in educational software that promotes the teaching of
educational Robotics in a virtual and economic environment.
Abstract: This article presents a simple way to perform programmed voice commands for the interface with commercial Digital and Analogue Input/Output PCI cards, used in Robotics and Automation applications. Robots and Automation equipment can "listen" to voice commands and perform several different tasks, approaching to the human behavior, and improving the human- machine interfaces for the Automation Industry. Since most PCI Digital and Analogue Input/Output cards are sold with several DLLs included (for use with different programming languages), it is possible to add speech recognition capability, using a standard speech recognition engine, compatible with the programming languages used. It was created in this work a Visual Basic 6 (the world's most popular language) application, that listens to several voice commands, and is capable to communicate directly with several standard 128 Digital I/O PCI Cards, used to control complete Automation Systems, with up to (number of boards used) x 128 Sensors and/or Actuators.