Abstract: Four phenylurea herbicides (isoproturon, chlortoluron, diuron and linuron) were dissolved in different water matrices in order to study their chemical degradation by using UV radiation, ozone and some advanced oxidation processes (UV/H2O2, O3/H2O2, Fenton reagent and the photo- Fenton system). The waters used were: ultra-pure water, a commercial mineral water, a groundwater and a surface water taken from a reservoir. Elimination levels were established for each herbicide and for several global quality parameters, and a kinetic study was performed in order to determine basic kinetic parameters of each reaction between the target phenylureas and these oxidizing systems.
Abstract: Principally, plants grown in soilless culture may be
attacked by the same pests and diseases as cultivated traditionally in
soil. The most destructive phytopathogens are fungi, such as
Phythium, Phytophthora and Fusarium, followed by viruses, bacteria
and nematodes. We investigated effect of carbon nanotube filters on
disease management of soilless culture. Tomato seedlings transplant
in plastic pots filled with a soilless media of vermiculite. The crop
irrigated and fertilized using a hydroponic nutrient solution. We used
carbon nanotube filters for nutrient solution disinfection. Our results
show that carbon nanotube filtration significantly reduces pathogens
on tomato plants. Fungal elimination (Fusarium oxysporum and
Pythium spp.) was usually successful at about 96 to 99.9% all over
the cultural season. It is seem that in tomato soilless culture,
nanofiltration constitutes a reliable method that allows control of the
development of diseases caused by pathogenic fungi
Abstract: DG application has received increasing attention during
recent years. The impact of DG on various aspects of distribution system
operation, such as reliability and energy loss, depend highly on DG
location in distribution feeder. Optimal DG placement is an important
subject which has not been fully discussed yet.
This paper presents an optimization method to determine optimal DG
placement, based on a cost/worth analysis approach. This method
considers technical and economical factors such as energy loss, load point
reliability indices and DG costs, and particularly, portability of DG. The
proposed method is applied to a test system and the impacts of different
parameters such as load growth rate and load forecast uncertainty (LFU)
on optimum DG location are studied.
Abstract: The effects of seawater and slurry ice bleeding methods on the sensory, microbiological and chemical quality changes of cod fillets during chilled storage were examined in this study. The results from sensory evaluation showed that slurry ice bleeding method prolonged the shelf life of cod fillets up to 13-14 days compared to 10-11 days for fish bled in seawater. Slurry ice bleeding method also led to a slower microbial growth and biochemical developments, resulting lower total plate count (TPC), H2S-producing bacteria count, total volatile basic nitrogen (TVB-N), trimethylamine (TMA), free fatty acid (FFA) content and higher phospholipid content (PL) compared to those of samples bled in seawater. The results of principle component analysis revealed that TPC, H2S-producing bacteria, TVB-N, TMA and FFA were in significant correlation. They were also in negative correlation with sensory evaluation (Torry score), PL and water holding capacity (WHC).
Abstract: This paper presents the results of a preventive maintenance application-based study and modeling of failure rates in breakers of electrical distribution systems. This is a critical issue in the reliability assessment of a system. In the analysis conducted in this paper, the impacts of failure rate variations caused by a preventive maintenance are examined. This is considered as a part of a Reliability Centered Maintenance (RCM) application program. A number of load point reliability indices is derived using the mathematical model of the failure rate, which is established using the observed data in a distribution system.
Abstract: The grey oyster mushroom, Pleurotus sajor-caju
(PSC), is a common edible mushroom and is now grown
commercially around the world for food. This fungus has been
broadly used as food or food ingredients in various food products for
a long time. To enhance the nutritional quality and sensory attributes
of bakery-based products, PSC powder is used in the present study to
partially replace wheat flour in baked product formulations. The
nutrient content and sensory properties of rice-porridge and
unleavened bread (paratha) incorporated with various levels of PSC
powder were studied. These food items were formulated with either
0%, 2%, 4% or 6% of PSC powder. Results show PSC powder
recorded β-glucan at 3.57g/100g. In sensory evaluation, consumers
gave higher score to both rice-porridge and paratha bread containing
2-4% PSC compared to those that are not added with PSC powder.
The paratha containing 4% PSC powder can be formulated with the
intention in improving overall acceptability of paratha bread.
Meanwhile, for rice-porridge, consumers prefer the formulated
product added with 4% PSC powder. In conclusion, the addition of
PSC powder to partially wheat flour can be recommended for the
purpose of enhancing nutritional composition and maintaining the
acceptability of carbohydrate-based products.
Abstract: A novel physico-chemical route to produce few layer graphene nanoribbons with atomically smooth edges is reported, via acid treatment (H2SO4:HNO3) followed by characteristic thermal shock processes involving extremely cold substances. Samples were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectroscopy. This method demonstrates the importance of having the nanotubes open ended for an efficient uniform unzipping along the nanotube axis. The average dimensions of these nanoribbons are approximately ca. 210 nm wide and consist of few layers, as observed by transmission electron microscopy. The produced nanoribbons exhibit different chiralities, as observed by high resolution transmission electron microscopy. This method is able to provide graphene nanoribbons with atomically smooth edges which could be used in various applications including sensors, gas adsorption materials, composite fillers, among others.
Abstract: High purity hydrogen and the valuable by-product of carbon nanotubes (CNTs) can be produced by the methane catalytic decomposition. The methane conversion and the performance of CNTs were determined by the choices of catalysts and the condition of decomposition reaction. In this paper, Ni/MgO and Ni/O-D (oxidized diamond) catalysts were prepared by wetness impregnation method. The effects of reaction temperature and space velocity of methane on the methane conversion were investigated in a fixed-bed. The surface area, structure and micrography were characterized with BET, XPS, SEM, EDS technology. The results showed that the conversion of methane was above 8% within 150 min (T=500) for 33Ni/O-D catalyst and higher than 25% within 120 min (T=650) for 41Ni/MgO catalyst. The initial conversion increased with the increasing temperature of the decomposition reaction, but their catalytic activities decreased rapidly while at too higher temperature. To decrease the space velocity of methane was propitious to promote the methane conversion, but not favor of the hydrogen yields. The appearance of carbon resulted from the methane decomposition lied on the support type and the condition of catalytic reaction. It presented as fiber shape on the surface of Ni/O-D at the relatively lower temperature such as 500 and 550, but as grain shape stacked on and overlayed on the surface of the metal nickel while at 650. The carbon fiber can form on the Ni/MgO surface at 650 and the diameter of the carbon fiber increased with the decreasing space velocity.
Abstract: Density functional theory (DFT) calculations were performed to calculate aluminum-27, boron-11, and nitrogen-14 quadrupole coupling constant (CQ) in the representative considered model of (6, 0) boron nitride-aluminum nitride nanotube junction (BN-AlNNT) for the first time. To this aim, 1.3 nm length of BNAlN consisting of 18 Al, 18 B, and 36 N atoms was selected where the end atoms capped by hydrogen atoms. The calculated CQ values for optimized BN-AlNNT system reveal different electrostatic environment in the mentioned system. The calculations were performed using the Gaussian 98 package of program.
Abstract: Ionanofluids are a new and innovative class of heat transfer fluids which exhibit fascinating thermophysical properties compared to their base ionic liquids. This paper deals with the findings of thermal conductivity and specific heat capacity of ionanofluids as a function of a temperature and concentration of nanotubes. Simulation results using ionanofluids as coolants in heat exchanger are also used to access their feasibility and performance in heat transfer devices. Results on thermal conductivity and heat capacity of ionanofluids as well as the estimation of heat transfer areas for ionanofluids and ionic liquids in a model shell and tube heat exchanger reveal that ionanofluids possess superior thermal conductivity and heat capacity and require considerably less heat transfer areas as compared to those of their base ionic liquids. This novel class of fluids shows great potential for advanced heat transfer applications.
Abstract: Cement, the most widely used construction material
is very brittle and characterized by low tensile strength and strain
capacity. Macro to nano fibers are added to cement to provide
tensile strength and ductility to it. Carbon Nanotube (CNT), one of
the nanofibers, has proven to be a promising reinforcing material in
the cement composites because of its outstanding mechanical
properties and its ability to close cracks at the nano level. The
experimental investigations for CNT reinforced cement is costly,
time consuming and involves huge number of trials. Mathematical
modeling of CNT reinforced cement can be done effectively and
efficiently to arrive at the mechanical properties and to reduce the
number of trials in the experiments. Hence, an attempt is made to
numerically study the effective mechanical properties of CNT
reinforced cement numerically using Representative Volume
Element (RVE) method. The enhancement in its mechanical
properties for different percentage of CNTs is studied in detail.
Abstract: In this study concept of experimental design is
successfully applied for the determination of optimum condition to
produce PP/SWCNT (Polypropylene/Single wall carbon nanotube)
nanocomposite. Central composite design as one of experimental
design techniques is employed for the optimization and statistical
determination of the significant factors influencing on the tensile
modulus and yield stress as mechanical properties of this
nanocomposite. The significant factors are SWCNT weight fraction
and acid treatment time for functionalizing the nanoparticles.
Optimum conditions are in 0.7 % of SWCNT weight fraction and 210
min as acid treatment time for 1112.75 ± 28 MPa as maximum tensile
modulus and in 216 min and 0.65 % as acid treatment time and
SWCNT weight fraction respectively for 40.26 ± 0.3 MPa as
maximum yield stress. Also after setting new experiments for test
these optimum conditions, found excelent agreement with predicted
values.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: In this article, a single application is suggested to determine the position of vehicles using Geographical Information Systems (GIS) and Geographical Position Systems (GPS). The part of the article material included mapping three dimensional coordinates to two dimensional coordinates using UTM or LAMBERT geographical methods, and the algorithm of conversion of GPS information into GIS maps is studied. Also, suggestions are given in order to implement this system based on web (called web based systems). To apply this system in IRAN, related official in this case are introduced and their duties are explained. Finally, economy analyzed is assisted according to IRAN communicational system.
Abstract: Stress-strain curve of inter-tube connected carbon nanotube (CNT) reinforced polymer composite under axial loading generated from molecular dynamics simulation is presented. Comparison of the response to axial mechanical loading between this composite system with composite systems reinforced by long, continuous CNTs (replicated via periodic boundary conditions) and short, discontinuous CNTs has been made. Simulation results showed that the inter-tube connection improved the mechanical properties of short discontinuous CNTs dramatically. Though still weaker than long CNT/polymer composite, more remarkable increase in the stiffness relative to the polymer was observed in the inter-tube connected CNT/polymer composite than in the discontinuous CNT/polymer composite. The manually introduced bridge break process resulted in a stress-strain curve of ductile fracture mode, which is consistent with the experimental result.
Abstract: Chemical and physical functionalization of multiwalled
carbon nanotubes (MWCNT) has been commonly practiced to
achieve better dispersion of carbon nanotubes (CNTs) in polymer
matrix. This work describes various functionalization methods (acidtreatment,
non-ionic surfactant treatment with TritonX-100),
fabrication of MWCNT/PP nanocomposites via melt blending and
characterization of mechanical properties. Microscopy analysis
(FESEM, TEM, XPS) showed effective purification of MWCNTs
under acid treatment, and better dispersion under both chemical and
physical functionalization techniques combined, in their respective
order. Tensile tests showed increase in tensile strength for the
nanocomposites that contain MWCNTs up to 2 wt%. A decrease in
tensile strength was seen in samples that contain 4 wt% of MWCNTs
for both raw and Triton X-100 functionalized, signifying MWCNT
degradation/rebundling at composition with higher content of
MWCNTs. For the acid-treated MWCNTs, however, the tensile
results showed slight improvement even at 4wt%, indicating effective
dispersion of MWCNTs.
Abstract: This work relates the development of an optical fiber
(OF) sensor for the detection and quantification of single walled
carbon nanotubes in aqueous solutions. The developed OF displays a
compact design, it requires less expensive materials and equipment
as well as low volume of sample (0.2 mL). This methodology was
also validated by the comparison of its analytical performance with
that of a standard methodology based on ultraviolet-visible
spectroscopy. The developed OF sensor follows the general SDS
calibration proposed for OF sensors as a more suitable calibration
fitting compared with classical calibrations.
Abstract: We study the typical domain size and configuration
character of a randomly perturbed system exhibiting continuous
symmetry breaking. As a model system we use rod-like objects
within a cubic lattice interacting via a Lebwohl–Lasher-type
interaction. We describe their local direction with a headless unit
director field. An example of such systems represents nematic LC or
nanotubes. We further introduce impurities of concentration p, which
impose the random anisotropy field-type disorder to directors. We
study the domain-type pattern of molecules as a function of p,
anchoring strength w between a neighboring director and impurity,
temperature, history of samples. In simulations we quenched the
directors either from the random or homogeneous initial
configuration. Our results show that a history of system strongly
influences: i) the average domain coherence length; and ii) the range
of ordering in the system. In the random case the obtained order is
always short ranged (SR). On the contrary, in the homogeneous case,
SR is obtained only for strong enough anchoring and large enough
concentration p. In other cases, the ordering is either of quasi long
range (QLR) or of long range (LR). We further studied memory
effects for the random initial configuration. With increasing external
ordering field B either QLR or LR is realized.
Abstract: Bode stability analysis based on transmission line
modeling (TLM) for single wall carbon nanotube (SWCNT)
interconnects used in 3D-VLSI circuits is investigated for the first
time. In this analysis, the dependence of the degree of relative
stability for SWCNT interconnects on the geometry of each tube has
been acquired. It is shown that, increasing the length and diameter of
each tube, SWCNT interconnects become more stable.
Abstract: We derive simple sets of equations to describe the microwave response of a thin film of magnetized hydrogen plasma in the presence of carbon nanotubes, which were grown by ironcatalyzed high-pressure disproportionation (HiPco). By considering the interference effects due to multiple reflections between thin plasma film interfaces, we present the effects of the continuously changing external magnetic field and plasma parameters on the reflected power, absorbed power, and transmitted power in the system. The simulation results show that the interference effects play an important role in the reflectance, transmittance and absorptance of microwave radiation at the magnetized plasma slab. As a consequence, the interference effects lead to a sinusoidal variation of the reflected intensity and can greatly reduce the amount of reflection power, but the absorption power increases.