Abstract: This study investigated the effect of oxygen and
micro-cracking on the flotation of low grade nickel sulphide ore. The
ore treated contained serpentine minerals which have a history of
being difficult to process efficiently. The use of oxygen as a bubbling
gas has been noted to be effective because it increases the pulp
potential. The desired effect of micro cracking the ore is that the
nickel sulphide minerals will become activated and this activation
will render these minerals more susceptible to react with potassium
amyl xanthate collectors, resulting in a higher recovery of nickel and
hinder the recovery of other undesired minerals contained in the ore.
Higher nickel recoveries were obtained when pure oxygen was used
as a bubbling gas rather than the conventional air. Microwave
cracking favored the recovery of nickel.
Abstract: This paper presents the results of corrosion fatigue
crack growth behaviour of a Ni-Cr-Mn steel commonly used in
marine applications. The effect of mechanical variables such as
frequency and load ratio on fatigue crack growth rate at various
stages has been studied using compact tension (C(T)) specimens
along the rolling direction of steel plate under 3.5% saturated NaCl
aqueous environment. The significance of crack closure on corrosion
fatigue, and the validity of Elber-s empirical linear crack closure
model with the ASTM compliance offset method have been
examined.
Fatigue crack growth rate is higher and threshold stress intensities
are lower in aqueous environment compared to the lab air conditions.
It is also observed that the crack growth rate increases at lower
frequencies. The higher stress ratio promotes the crack growth. The
effect of oxidization and corrosion pit formation is very less as the
stress ratio is increased. It is observed that as stress ratios are
increased, the Elber-s crack closure model agrees well with the crack
closure estimated by the ASTM compliance offset method for tests
conducted at 5Hz frequency compared to tests conducted at 1Hz in
corrosive environment.
Abstract: Buildings with floating column are highly undesirable built in seismically active areas. Many urban multi-storey buildings today have floating column buildings which are adopted to accommodate parking at ground floor or reception lobbies in the first storey. The earthquake forces developed at different floor levels in a building need to be brought down along the height to the ground by the shortest path; any deviation or discontinuity in this load transfer path results in poor performance of the building. Floating column buildings are severely damaged during earthquake. Damage on this structure can be reduce by taking the effect of infill wall. This paper presents the effect of stiffness of infill wall to the damage occurred in floating column building when ground shakes. Modelling and analysis are carried out by non linear analysis programme IDARC-2D. Damage occurred in beams, columns, storey are studied by formulating modified Park & Ang model to evaluate damage indices. Overall structural damage indices in buildings due to shaking of ground are also obtained. Dynamic response parameters i.e. lateral floor displacement, storey drift, time period, base shear of buildings are obtained and results are compared with the ordinary moment resisting frame buildings. Formation of cracks, yield, plastic hinge, are also observed during analysis.
Abstract: Fiber optic sensor technology offers the possibility of
sensing different parameters like strain, temperature, pressure in
harsh environment and remote locations. these kinds of sensors
modulates some features of the light wave in an optical fiber such an
intensity and phase or use optical fiber as a medium for transmitting
the measurement information.
The advantages of fiber optic sensors in contrast to conventional
electrical ones make them popular in different applications and now a
day they consider as a key component in improving industrial
processes, quality control systems, medical diagnostics, and
preventing and controlling general process abnormalities.
This paper is an introduction to fiber optic sensor technology and
some of the applications that make this branch of optic technology,
which is still in its early infancy, an interesting field.
Abstract: Cements, which are intrinsically brittle materials, can
exhibit a degree of pseudo-ductility when reinforced with a sufficient
volume fraction of a fibrous phase. This class of materials, called
Engineered Cement Composites (ECC) has the potential to be used in
future tunneling applications where a level of pseudo-ductility is
required to avoid brittle failures. However uncertainties remain
regarding mechanical performance. Previous work has focused on
comparatively thin specimens; however for future civil engineering
applications, it is imperative that the behavior in tension of thicker
specimens is understood. In the present work, specimens containing
cement powder and admixtures have been manufactured following
two different processes and tested in tension. Multiple matrix
cracking has been observed during tensile testing, leading to a
“strain-hardening" behavior, confirming the possible suitability of
ECC material when used as thick sections (greater than 50mm) in
tunneling applications.
Abstract: Pressure vessels are usually operating at temperatures
where the conditions of linear elastic fracture mechanics are no
longer met because massive plasticity precedes crack propagation. In
this work the development of a surface crack in a pressure vessel
subject to bending and tension under elastic-plastic fracture
mechanics conditions was investigated. Finite element analysis was
used to evaluate the hydrostatic stress, the J-integral and crack
growth for semi-elliptical surface-breaking cracks. The results
showed non-uniform stress triaxiality and crack driving force around
the crack front at large deformation levels. Different ductile crack
extensions were observed which emphasis the dependent of ductile
tearing on crack geometry and type of loading. In bending the crack
grew only beneath the surface, and growth was suppressed at the
deepest segment. This contrasts to tension where the crack breaks
through the thickness with uniform growth along the entire crack
front except at the free surface. Current investigations showed that
the crack growth developed under linear elastic fracture mechanics
conditions will no longer be applicable under ductile tearing
scenarios.
Abstract: This study offers a new simple method for assessing
an axial part-through crack in a pipe wall. The method utilizes simple
approximate expressions for determining the fracture parameters K,
J, and employs these parameters to determine critical dimensions of a
crack on the basis of equality between the J-integral and the J-based
fracture toughness of the pipe steel. The crack tip constraint is taken
into account by the so-called plastic constraint factor C, by which the
uniaxial yield stress in the J-integral equation is multiplied. The
results of the prediction of the fracture condition are verified by burst
tests on test pipes.
Abstract: Protective coatings that resist oxide scale growth and
decrease chromium evaporation are necessary to make stainless steel
interconnect materials for long-term durable operation of solid oxide
fuel cells (SOFCs). In this study a layer of cobalt was electroplated
on the surface of AISI 441 ferritic stainless steel which is used in
solid oxide fuel cells for interconnect applications. The oxidation
behavior of coated substrates was studied as a function of time at
operating conditions of SOFCs. Cyclic oxidation has been also tested
at 800ºC for 100 cycles. Cobalt coating during isothermal oxidation
caused to the oxide growth resistance by limiting the outward
diffusion of Cr cation and the inward diffusion of oxygen anion.
Results of cyclic oxidation exhibited that coated substrates
demonstrate an excellent resistance against the spallation and
cracking.
Abstract: This work presents the experimental results obtained
at a pilot plant which works with a slow, wet and catalytic pyrolysis
process of dry fowl manure. This kind of process mainly consists in
the cracking of the organic matrix and in the following reaction of
carbon with water, which is either already contained in the organic
feed or added, to produce carbon monoxide and hydrogen. Reactions
are conducted in a rotating reactor maintained at a temperature of
500°C; the required amount of water is about 30% of the dry organic
feed. This operation yields a gas containing about 59% (on a volume
basis) of hydrogen, 17% of carbon monoxide and other products such
as light hydrocarbons (methane, ethane, propane) and carbon
monoxide in lesser amounts. The gas coming from the reactor can be
used to produce not only electricity, through internal combustion
engines, but also heat, through direct combustion in industrial
boilers. Furthermore, as the produced gas is devoid of both solid
particles and pollutant species (such as dioxins and furans), the
process (in this case applied to fowl manure) can be considered as an
optimal way for the disposal and the contemporary energetic
valorization of organic materials, in such a way that is not damaging
to the environment.
Abstract: The first and basic cause of the failure of concrete is repeated freezing (thawing) of moisture contained in the pores, microcracks, and cavities of the concrete. On transition to ice, water existing in the free state in cracks increases in volume, expanding the recess in which freezing occurs. A reduction in strength below the initial value is to be expected and further cycle of freezing and thawing have a further marked effect. By using some experimental parameters like nuclear magnetic resonance variation (NMR), enthalpy-temperature (or heat capacity) variation, we can resolve between the various water states and their effect on concrete properties during cooling through the freezing transition temperature range. The main objective of this paper is to describe the principal type of water responsible for the reduction in strength and structural damage (frost damage) of concrete following repeated freeze –thaw cycles. Some experimental work was carried out at the institute of cryogenics to determine what happens to water in concrete during the freezing transition.
Abstract: Cement, the most widely used construction material
is very brittle and characterized by low tensile strength and strain
capacity. Macro to nano fibers are added to cement to provide
tensile strength and ductility to it. Carbon Nanotube (CNT), one of
the nanofibers, has proven to be a promising reinforcing material in
the cement composites because of its outstanding mechanical
properties and its ability to close cracks at the nano level. The
experimental investigations for CNT reinforced cement is costly,
time consuming and involves huge number of trials. Mathematical
modeling of CNT reinforced cement can be done effectively and
efficiently to arrive at the mechanical properties and to reduce the
number of trials in the experiments. Hence, an attempt is made to
numerically study the effective mechanical properties of CNT
reinforced cement numerically using Representative Volume
Element (RVE) method. The enhancement in its mechanical
properties for different percentage of CNTs is studied in detail.
Abstract: In this paper, the effect of bolt clamping force on the fatigue behavior of bolted single lap joints of aluminum alloy 2024- T3 have been studied using numerical finite element method. To do so, a three dimensional model according to the bolted single lap joint has been created and numerical analysis has been carried out using finite element based package. Then the stress distribution and also the slip amplitudes have been calculated in the critical regions and the outcome have been compared with the available experimental fatigue tests results. The numerical results show that in low applied clamping force, the fatigue failure of the specimens occur around the stress concentration location (the bolted hole edge) due to the tensile stresses and thus fatigue crack propagation, but with increase of the clamping force, the fatigue life increases and the cracks nucleate and propagate far from the hole edge because of fretting fatigue. In other words, with the further increase of clamping force value of the joint, the fatigue life reduces due to occurrence of the fretting fatigue in the critical location where the slip amplitude is within its critical occurs earlier.
Abstract: Reinforced concrete has good durability and excellent structural performance. But there are cases of early deterioration due to a number of factors, one prominent factor being corrosion of steel reinforcement. The process of corrosion sets in due to ingress of moisture, oxygen and other ingredients into the body of concrete, which is unsound, permeable and absorbent. Cracks due to structural and other causes such as creep, shrinkage, etc also allow ingress of moisture and other harmful ingredients and thus accelerate the rate of corrosion. There are several interactive factors both external and internal, which lead to corrosion of reinforcement and ultimately failure of structures. Suitable addition of mineral admixture like silica fume (SF) in concrete improves the strength and durability of concrete due to considerable improvement in the microstructure of concrete composites, especially at the transition zone. Secondary reinforcement in the form of fibre is added to concrete, which provides three dimensional random reinforcement in the entire mass of concrete. Reinforced concrete beams of size 0.1 m X 0.15 m and length 1m have been cast using M 35 grade of concrete. The beams after curing process were subjected to corrosion process by impressing an external Direct Current (Galvanostatic Method) for a period of 15 days under stressed and unstressed conditions. The corroded beams were tested by applying two point loads to determine the ultimate load carrying capacity and cracking pattern and the results of specimens were compared with that of the companion specimens. Gravimetric method is used to quantify corrosion that has occurred.
Abstract: The aim of this investigation is to study the
performance of the new generation of the PVD coated grade and to
map the influence of cutting conditions on the tool life in milling of
ADI (Austempered Ductile Iron). The results show that chipping is
the main wear mechanism which determines the tool life in dry
condition and notch wear in wet condition for this application. This
due to the different stress mechanisms and preexisting cracks in the
coating. The wear development shows clearly that the new PVD
coating (C20) has the best ability to delay the chipping growth. It
was also found that a high content of Al in the new coating (C20)
was especially favorable compared to a TiAlN multilayer with lower
Al content (C30) or CVD coating. This is due to fine grains and low
compressive stress level in the coating which increase the coating
ability to withstand the mechanical and thermal impact. It was also
found that the use of coolant decreases the tool life with 70-80%
compare to dry milling.
Abstract: In this paper, the effect of modified clay on the
mechanical efficiency of epoxy resin is examined. Studies by X ray
diffraction and microscopic transient electron method show that
modified clay distribution in polymer area is intercalated kind.
Examination the results of mechanical tests shows that existence of
modified clay in epoxy area increases pressure yield strength, tension
module and nano composite fracture toughness in relate of pure
epoxy. By microscopic examinations it is recognized too that the
action of toughness growth of this kind of nano composite is due to
crack deflection, formation of new surfaces and fracture of clay piles.
Abstract: The nearly 21-year-old Jiujiang Bridge, which is suffering from uneven line shape, constant great downwarping of the main beam and cracking of the box girder, needs reinforcement and cable adjustment. It has undergone cable adjustment for twice with incomplete data. Therefore, the initial internal force state of the Jiujiang Bridge is identified as the key for the cable adjustment project. Based on parameter identification by means of static force test data, this paper suggests determining the initial internal force state of the cable-stayed bridge according to the cable force-displacement relationship parameter identification method. That is, upon measuring the displacement and the change in cable forces for twice, one can identify the parameters concerned by means of optimization. This method is applied to the cable adjustment, replacement and reinforcement project for the Jiujiang Bridge as a guidance for the cable adjustment and reinforcement project of the bridge.
Abstract: Using the finite element analyses, this paper discusses the effects of temperature-dependent material properties on the stress and temperature fields in a cracked metal plate under the electric current load. The practical and complicated results are obtained when the temperature-dependent material properties are adopted in the analysis. If the simplified (temperature-independent) material properties are used, incorrect results will be obtained.
Abstract: In hypersonic environments, the aerothermal effect
makes it difficult for the optical side windows of optical guided
missiles to withstand high heat. This produces cracking or breaking,
resulting in an inability to function. This study used computational
fluid mechanics to investigate the external cooling jet conditions of
optical side windows. The turbulent models k-ε and k-ω were
simulated. To be in better accord with actual aerothermal
environments, a thermal radiation model was added to examine
suitable amounts of external coolants and the optical window
problems of aero-thermodynamics. The simulation results indicate that
when there are no external cooling jets, because airflow on the optical
window and the tail groove produce vortices, the temperatures in these
two locations reach a peak of approximately 1600 K. When the
external cooling jets worked at 0.15 kg/s, the surface temperature of
the optical windows dropped to approximately 280 K. When adding
thermal radiation conditions, because heat flux dissipation was faster,
the surface temperature of the optical windows fell from 280 K to
approximately 260 K. The difference in influence of the different
turbulence models k-ε and k-ω on optical window surface temperature
was not significant.
Abstract: This paper study the behavior of the solution at the crack edges for an elliptical crack with developing cusps, Ω in the plane elasticity subjected to shear loading. The problem of finding the resulting shear stress can be formulated as a hypersingular integral equation over Ω and it is then transformed into a similar equation over a circular region, D, using conformal mapping. An appropriate collocation points are chosen on the region D to reduce the hypersingular integral equation into a system of linear equations with (2N+1)(N+1) unknown coefficients, which will later be used in the determination of shear stress intensity factors and maximum shear stress intensity. Numerical solution for the considered problem are compared with the existing asymptotic solution, and displayed graphically. Our results give a very good agreement to the existing asymptotic solutions.
Abstract: The study was performed to evaluate the effect of Sgirdling,
fruit thinning plus bagging with 2,4-D application, fruit
thinning plus bagging on growth and quality of wax apple fruit.
Girdling was applied three week before flowering. The 2,4-D was
sprayed at the small bud and petal fall stage. The effect of all
treatments on fruit growth was measured weekly. The physical and
biochemical quality characteristics of the fruits were recorded. The
results showed that no significant effect on number of bud among
treatments. S-girdling, 2,4-D application produced the lowest bud
drop, fruit drop compared to untreated control. Moreover, S-girdling
enhanced faster fruit growth producing the best final fruit length and
diameter than the control treatment. It was also observed that Sgirdling
greatly increased fruit set, fruit weight as well as total
soluble solid, reduced fruit crack, and titratable acidity. In
conclusion, S-girdling had a distinctive and significant effect on most
of the fruit quality characteristics assessed. Application 2,4-D was
also recommended as the industry norm to increase fruit set, and fruit
quality in wax apple.