Abstract: Reinforced concrete stair slabs with mid landings i.e.
Dog-legged shaped are conventionally designed as per specifications
of standard codes of practices which guide about the effective span
according to the varying support conditions. Presently, the behavior
of such slabs has been investigated using Finite Element method. A
single flight stair slab with landings on both sides and supported at
ends on wall, and a multi flight stair slab with landings and six
different support arrangements have been analyzed. The results
obtained for stresses, strains and deflections are used to describe the
behavior of such stair slabs, including locations of critical moments
and deflections. Values of critical moments obtained by F.E. analysis
have also have been compared with that obtained from conventional
analysis. Analytical results show that the moments are also critical
near the kinks i.e. junction of mid-landing and inclined waist slab.
This change in the behavior of dog-legged stair slab may be due to
continuity of the material in transverse direction in two landings
adjoining the waist slab, hence additional stiffness achieved. This
change in the behavior is generally not taken care of in conventional
method of design.
Abstract: In this paper, the signal transmission analysis of the
semicircle-shaped via structure for the differential pairs is presented in
the frequency range up to 10 GHz. In order to improve the signal
transmission properties in the differential pairs, single via is separated
centrally into two semicircle-shaped sections, which are
interconnected with the traces of differential pairs respectively. This
via structure make possible to route differential pairs using only one
via. In addition, it can improve impedance discontinuity around its
region and then enhance the signal transmission properties in the
differential pairs. The electrical analysis such as S-parameter
calculation and eye diagram simulation has been performed to
investigate the improvement of the signal transmission property in the
differential pairs with new via structure.
Abstract: Modeling of Panel Zone (PZ) seismic behavior,
because of its role in overall ductility and lateral stiffness of steel
moment frames, has been considered a challenge for years. There are
some studies regarding the effects of different doubler plates
thicknesses and geometric properties of PZ on its seismic behavior.
However, there is not much investigation on the effects of number of
provided continuity plates in case of presence of one triangular
haunch, two triangular haunches and rectangular haunch (T shape
haunches) for exterior columns. In this research first detailed finite
element models of 12tested connection of SAC joint venture were
created and analyzed then obtained cyclic behavior backbone curves
of these models besides other FE models for similar tests were used
for neural network training. Then seismic behavior of these data is
categorized according to continuity plate-s arrangements and
differences in type of haunches. PZ with one-sided haunches have
little plastic rotation. As the number of continuity plates increases
due to presence of two triangular haunches (four continuity plate),
there will be no plastic rotation, in other words PZ behaves in its
elastic range. In the case of rectangular haunch, PZ show more plastic
rotation in comparison with one-sided triangular haunch and
especially double-sided triangular haunches. Moreover, the models
that will be presented in case of triangular one-sided and double-
sided haunches and rectangular haunches as a result of this study
seem to have a proper estimation of PZ seismic behavior.
Abstract: The exploration of this paper will focus on the Cshaped
transition curve. This curve is designed by using the concept
of circle to circle where one circle lies inside other. The degree of
smoothness employed is curvature continuity. The function used in
designing the C-curve is Bézier-like cubic function. This function has
a low degree, flexible for the interactive design of curves and
surfaces and has a shape parameter. The shape parameter is used to
control the C-shape curve. Once the C-shaped curve design is
completed, this curve will be applied to design spur gear tooth. After
the tooth design procedure is finished, the design will be analyzed by
using Finite Element Analysis (FEA). This analysis is used to find
out the applicability of the tooth design and the gear material that
chosen. In this research, Cast Iron 4.5 % Carbon, ASTM A-48 is
selected as a gear material.
Abstract: Sustainable development is one of the most debated
issues, recently. In terms of providing more livable Earth continuity,
while Production activities are going on, on the other hand protecting
the environment has importance. As a strategy for sustainable
development, eco-innovation is the application of innovations to
reduce environmental burdens. Endeavors to understand ecoinnovation
processes have been affected from environmental
economics and innovation economics from neoclassical economics,
and evolutionary economics other than neoclassical economics. In
the light of case study analyses, this study aims to display activities
in this field through case studies after explaining the theoretical
framework of eco-innovations. This study consists of five sections
including introduction and conclusion. In the second part of the study
identifications of the concepts related with eco-innovation are
described and eco-innovations are classified. Third section considers
neoclassical and evolutionary approaches from neoclassical
economics and evolutionary economics, respectively. Fourth section
gives the case studies of successful eco-innovations. Last section is
the conclusion part and offers suggestions for future eco-innovation
research according to the theoretical framework and the case studies.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasi-stationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: Evaluation of contact pressure, surface and
subsurface contact stresses are essential to know the functional
response of surface coatings and the contact behavior mainly depends
on surface roughness, material property, thickness of layer and the
manner of loading. Contact parameter evaluation of real rough
surface contacts mostly relies on statistical single asperity contact
approaches. In this work, a three dimensional layered solid rough
surface in contact with a rigid flat is modeled and analyzed using
finite element method. The rough surface of layered solid is
generated by FFT approach. The generated rough surface is exported
to a finite element method based ANSYS package through which the
bottom up solid modeling is employed to create a deformable solid
model with a layered solid rough surface on top. The discretization
and contact analysis are carried by using the same ANSYS package.
The elastic, elastoplastic and plastic deformations are continuous in
the present finite element method unlike many other contact models.
The Young-s modulus to yield strength ratio of layer is varied in the
present work to observe the contact parameters effect while keeping
the surface roughness and substrate material properties as constant.
The contacting asperities attain elastic, elastoplastic and plastic states
with their continuity and asperity interaction phenomena is inherently
included. The resultant contact parameters show that neighboring
asperity interaction and the Young-s modulus to yield strength ratio
of layer influence the bulk deformation consequently affect the
interface strength.
Abstract: Contemporary science and technologies largely widen
the gap between the spiritual and rational of the society. Industrial
and technological breakthroughs might radically affect most
processes in the society, thus losing the cultural heritage. The
thinkers recognized the dangers of the decadence in the first place. In
the present article the ways of preserving cultural heritage have been
investigated. Memory has always been a necessary condition for selfidentification,
- continuity is based on this. The authors have
supported the hypothesis that continuity and ethnic memory are the
very mechanisms that preserve cultural heritage. Such problemformulating
will facilitate another, new look at the material, spiritual
and arts spheres of the cultural heritage of numerous ethnic groups.
The fundamental works by major European and Kazakh scientists
have been taken as a basis for the research done.
Abstract: A real time image-guided electroplating system is
proposed in this paper. Unlike previous electroplating systems, instead
of using the intermittent mode to electroplate 500um long copper
specimen, a CCD camera and a motion controller are used to adjust
anode-cathode distance to obtain better results. Since the image of the
gap distance is highly deteriorated due to complex chemical-electrical
operation inside the electrolyte, to determine the gap distance, an
image processing algorithm is developed and mainly based on the
entropy and energy values. In addition, the color and incidence
direction of light source are also discussed to help the image process in
this paper. From the experiment results, the specimens created by the
proposed system show better structure, better uniformity and better
finishing surface compared to those by previous intermittent
electroplating setup.
Abstract: Societal security, continuity scenarios and methodological cycling approach explained in this article. Namely societal security organizational challenges ask implementation of international standards BS 25999-2 & global ISO 22300 which is a family of standards for business continuity management system. Efficient global organization system is distinguished of high entity´s complexity, connectivity & interoperability, having not only cooperative relations in a fact. Competing business have numerous participating ´enemies´, which are in apparent or hidden opponent and antagonistic roles with prosperous organization system, resulting to a crisis scene or even to a battle theatre. Organization business continuity scenarios are necessary for such ´a play´ preparedness, planning, management & overmastering in real environments.
Abstract: A catastrophic earthquake measuring 6.3 on the
Richter scale struck the Christchurch, New Zealand Central Business
District on February 22, 2012, abruptly disrupting the business of
teaching and learning at Christchurch Polytechnic Institute of
Technology. This paper presents the findings from a study
undertaken about the complexity of delivering an educational
programme in the face of this traumatic natural event. Nine
interconnected themes emerged from this multiple method study:
communication, decision making, leader- and follower-ship,
balancing personal and professional responsibilities, taking action,
preparedness and thinking ahead, all within a disruptive and uncertain
context. Sustainable responses that maximise business continuity, and
provide solutions to practical challenges, are among the study-s
recommendations.
Abstract: Arc welding creates a weld pool to realize continuity between pieces of assembly. The thermal history of the weld is dependent on heat transfer and fluid flow in the weld pool. The metallurgical transformation during welding and cooling are modeled in the literature only at solid state neglecting the fluid flow. In the present paper we associate a heat transfer – fluid flow and metallurgical model for the 16MnD5 steel. The metallurgical transformation model is based on Leblond model for the diffusion kinetics and on the Koistinen-Marburger equation for Marteniste transformation. The predicted thermal history and metallurgical transformations are compared to a simulation without fluid phase. This comparison shows the great importance of the fluid flow modeling.
Abstract: The NGN (Next Generation Network), which can
provide advanced multimedia services over an all-IP based network, has been the subject of much attention for years. While there have
been tremendous efforts to develop its architecture and protocols, especially for IMS, which is a key technology of the NGN, it is far
from being widely deployed. However, efforts to create an advanced
signaling infrastructure realizing many requirements have resulted in a
large number of functional components and interactions between those
components. Thus, the carriers are trying to explore effective ways to
deploy IMS while offering value-added services. As one such
approach, we have proposed a self-organizing IMS. A self-organizing
IMS enables IMS functional components and corresponding physical
nodes to adapt dynamically and automatically based on situation such
as network load and available system resources while continuing IMS
operation. To realize this, service continuity for users is an important
requirement when a reconfiguration occurs during operation. In this
paper, we propose a mechanism that will provide service continuity to
users and focus on the implementation and describe performance
evaluation in terms of number of control signaling and processing time
during reconfiguration