Abstract: Transient simulation of the hydrogen-assisted self-ignition of propane-air mixtures were carried out in platinum-coated micro-channels from ambient cold-start conditions, using a two-dimensional model with reduced-order reaction schemes, heat conduction in the solid walls, convection and surface radiation heat transfer. The self-ignition behavior of hydrogen-propane mixed fuel is analyzed and compared with the heated feed case. Simulations indicate that hydrogen can successfully cause self-ignition of propane-air mixtures in catalytic micro-channels with a 0.2 mm gap size, eliminating the need for startup devices. The minimum hydrogen composition for propane self-ignition is found to be in the range of 0.8-2.8% (on a molar basis), and increases with increasing wall thermal conductivity, and decreasing inlet velocity or propane composition. Higher propane-air ratio results in earlier ignition. The ignition characteristics of hydrogen-assisted propane qualitatively resemble the selectively inlet feed preheating mode. Transient response of the mixed hydrogen- propane fuel reveals sequential ignition of propane followed by hydrogen. Front-end propane ignition is observed in all cases. Low wall thermal conductivities cause earlier ignition of the mixed hydrogen-propane fuel, subsequently resulting in low exit temperatures. The transient-state behavior of this micro-scale system is described, and the startup time and minimization of hydrogen usage are discussed.
Abstract: Optimisation of the physical and mechanical properties of cold rolled thin strips is achieved by controlling the rolling parameters. In this paper, the factors affecting the asymmetrical cold rolling of thin low carbon steel strip have been studied at a speed ratio of 1.1 without lubricant applied. The effect of rolling parameters on the resulting microstructure was also investigated. It was found that under dry condition, work roll shifting and work roll cross angle can improve the strip profile, and the result is more significant with an increase of work roll cross angle rather than that of work roll shifting. However, there was no obvious change in microstructure. In addition, effects of rolling parameters on strip profile and microstructure have also been discussed.
Abstract: In this study, the influence of rolling process parameters such as the work roll cross angle and work roll shifting value on the strip shape and profile of aluminum have been investigated under dry conditions at a speed ratio of 1.3 using Hille 100 experimental mill. The strip profile was found to improve significantly with increase in work roll cross angle from 0o to 1o, with an associated decrease in rolling force. The effect of roll shifting (from 0 to 8mm) was not as significant as the roll cross angle. However, an increase in work roll shifting value achieved a similar decrease in rolling force as that of work roll cross angle. The effect of work roll shifting was also found to be maximum at an optimum roll speed of 0.0986 m/s for the desired thickness. Of all these parameters, the most significant effect of the strip shape profile was observed with variation of work roll cross angle. However, the rolling force can be a significantly reduced by either increasing the the work roll cross angle or work roll shifting.
Abstract: This paper outlines the development of an
experimental technique in quantifying supersonic jet flows, in an
attempt to avoid seeding particle problems frequently associated with
particle-image velocimetry (PIV) techniques at high Mach numbers.
Based on optical flow algorithms, the idea behind the technique
involves using high speed cameras to capture Schlieren images of the
supersonic jet shear layers, before they are subjected to an adapted
optical flow algorithm based on the Horn-Schnuck method to
determine the associated flow fields. The proposed method is capable
of offering full-field unsteady flow information with potentially
higher accuracy and resolution than existing point-measurements or
PIV techniques. Preliminary study via numerical simulations of a
circular de Laval jet nozzle successfully reveals flow and shock
structures typically associated with supersonic jet flows, which serve
as useful data for subsequent validation of the optical flow based
experimental results. For experimental technique, a Z-type Schlieren
setup is proposed with supersonic jet operated in cold mode,
stagnation pressure of 4 bar and exit Mach of 1.5. High-speed singleframe
or double-frame cameras are used to capture successive
Schlieren images. As implementation of optical flow technique to
supersonic flows remains rare, the current focus revolves around
methodology validation through synthetic images. The results of
validation test offers valuable insight into how the optical flow
algorithm can be further improved to improve robustness and
accuracy. Despite these challenges however, this supersonic flow
measurement technique may potentially offer a simpler way to
identify and quantify the fine spatial structures within the shock shear
layer.
Abstract: Despite the wide spread use of synthetic dyes, natural
dyes are still exploited and used to enhance its inherent aesthetic
qualities as a major material for beautification of the body. Centuries
before the discovery of synthetic dyes, natural dyes were the only
source of dye open to mankind. Dyes are extracted from plant -
leaves, roots and barks, insect secretions, and minerals. However,
research findings have made it clear that of all, plants- leaves, roots,
barks or flowers are the most explored and exploited in which henna
(Lawsonia innermis L.) is one of those plants. Experiment has also
shown that henna is used in body painting in conjunction with an
alkaline (Ammonium Sulphate) as a fixing agent. This of course
gives a clue that if colour derived from henna is properly
investigated, it may not only be used for body decoration but
possibly, may have affinity to fiber substrate. This paper investigates
the dyeing potentials – dye ability and fastness qualities of henna dye
extracts on cotton and linen fibers using mordants like ammonium
sulphate and other alkalis (hydrosulphate and caustic soda, potash,
common salt, potassium alum). Hot and cold water and ethanol
solvent were used in the extraction of the dye to investigate the most
effective method, dye ability, and fastness qualities of these extracts
under room temperature. The results of the experiment show that
cotton have a high rate of dye intake than other fiber. On a similar
note, the colours obtained depend most on the solvent used. In
conclusion, hot water extraction appears more effective. While the
colours obtained from ethanol and both cold hot methods of
extraction range from light to dark yellow, light green to army green
and to some extent shades of brown hues.
Abstract: Thermoacoustic refrigerator is a cooling device which
uses the acoustic waves to produce the cooling effect. The aim of this
paper is to explore the experimental and numerical feasibility of a
standing-wave thermoacoustic refrigerator. The effects of the stack
length, position of stack and operating frequency on the cooling
performance are carried out. The circular pore stacks are tested under
the atmospheric pressure. A low-cost loudspeaker is used as an
acoustic driver. The results show that the location of stack installed in
resonator tube has a greater effect on the cooling performance, than
the stack length and operating frequency, respectively. The
temperature difference across the ends of stack can be generated up
to 13.7°C, and the temperature of cold-end is dropped down by 5.3°C
from the ambient temperature.
Abstract: The purpose of this study is to propose an effective method to improve frictional coefficient between shoe rubber soles with added glass fibers and the surfaces of icy and snowy road in order to prevent slip-and-fall accidents by the users. The additional fibers into the rubber were uniformly tilted to the perpendicular direction of the frictional surface, where tilting angles were -60, -30, +30, +60, 90 degrees and 0 (as normal specimen), respectively. It was found that parallel arraignment was effective to improve the frictional coefficient when glass fibers were embedded in the shoe rubber, while perpendicular to normal direction of the embedded glass fibers on the shoe surface was also effective to do that once after they were exposed from the shoe rubber with its abrasion. These improvements were explained by the increase of stiffness against the shear deformation of the rubber at critical frictional state and adequate scratching of fibers when fibers were protruded in perpendicular to frictional direction, respectively. Most effective angle of tilting of frictional coefficient between rubber specimens and a stone was perpendicular (= 0 degree) to frictional direction. Combinative modified rubber specimen having 2 layers was fabricated where tilting angle of protruded fibers was 0 degree near the contact surface and tilting angle of embedded fibers was 90 degrees near back surface in thickness direction to further improve the frictional coefficient. Current study suggested that effective arraignments in tilting angle of the added fibers should be applied in designing rubber shoe soles to keep the safeties for users in regions of cold climates.
Abstract: The floor beams of steel buildings, cold-formed steel
floor joists in particular, often require large web openings, which may
affect their shear capacities. A cost effective way to mitigate the
detrimental effects of such openings is to weld/fasten reinforcements.
A difficulty associated with an experimental investigation to establish
suitable reinforcement schemes for openings in shear zone is that
moment always coexists with the shear, and thus, it is impossible to
create pure shear state in experiments, resulting in moment
influenced results. However, Finite Element Method (FEM) based
analysis can be conveniently used to investigate the pure shear
behaviour of webs including webs with reinforced openings. This
paper presents the details associated with the finite element analysis
of thick/thin-plates (representing the web of hot-rolled steel beam,
and the web of a cold-formed steel member) having a large
reinforced opening. The study considered simply-supported
rectangular plates subjected to in-plane shear loadings until failure
(including post-buckling behaviour). The plate was modelled using
geometrically non-linear quadrilateral shell elements, and non-linear
stress-strain relationship based on experiments. Total Langrangian
with large displacement/small strain formulation was used for such
analyses. The model also considered the initial geometric
imperfections. This study considered three reinforcement schemes,
namely, flat, lip, and angle reinforcements. This paper discusses the
modelling considerations and presents the results associated with the
various reinforcement schemes under consideration.
Abstract: This study focuses on the hydro-geology and chemical
constituents analysis of Ikogosi Warm Spring waters in South West
Nigeria. Ikogosi warm spring is a global tourist attraction because it
has both warm and cold spring sources. Water samples from the cold
spring, warm spring and the meeting point were collected, analyzed
and the result shows close similarity in temperature, hydrogen iron
concentration (pH), alkalinity, hardness, Calcium, Magnesium,
Sodium, Iron, total dissolved solid and heavy metals. The measured
parameters in the water samples are within World Health
Organisation standards for fresh water. The study of the geology of
the warm spring reveals that the study area is underlain by a group of
slightly migmatised to non-migmatised paraschists and meta-igneous
rocks. Also, concentration levels of selected heavy metals, (Copper,
Cadmium, Zinc, Arsenic and Cromium) were determined in the water
(ppm) samples. Chromium had the highest concentration value of
1.52ppm (an average of 49.67%) and Cadmium had the lowest
concentration with value of 0.15ppm (an average of 4.89%).
Comparison of these results showed that, their mean levels are within
the standard values obtained in Nigeria. It can be concluded that both
warm and spring water are safe for drinking.
Abstract: Myocardial infarction is one of the leading causes of
death in the world. Some of these deaths occur even before the
patient reaches the hospital. Myocardial infarction occurs as a result
of impaired blood supply. Because the most of these deaths are due to
coronary artery disease, hence the awareness of the warning signs of
a heart attack is essential. Some heart attacks are sudden and intense,
but most of them start slowly, with mild pain or discomfort, then
early detection and successful treatment of these symptoms is vital to
save them. Therefore, importance and usefulness of a system
designing to assist physicians in early diagnosis of the acute heart
attacks is obvious. The main purpose of this study would be to enable patients to
become better informed about their condition and to encourage them
to seek professional care at an earlier stage in the appropriate
situations. For this purpose, the data were collected on 711 heart
patients in Iran hospitals. 28 attributes of clinical factors can be
reported by patients; were studied. Three logistic regression models
were made on the basis of the 28 features to predict the risk of heart
attacks. The best logistic regression model in terms of performance
had a C-index of 0.955 and with an accuracy of 94.9%. The variables,
severe chest pain, back pain, cold sweats, shortness of breath, nausea
and vomiting, were selected as the main features.
Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: Second generation military Filipino Amerasians
comprise a formidable contemporary segment of the estimated
250,000-plus biracial Amerasians in the Philippines today. Overall,
they are a stigmatized and socioeconomically marginalized diaspora;
historically, they were abandoned or estranged by U.S. military
personnel fathers assigned during the century-long Colonial, Post-
World War II and Cold War Era of permanent military basing (1898-
1992). Indeed, U.S. military personnel are assigned in smaller
numbers in the Philippines today. This inquiry is an outgrowth of two
recent small sample studies. The first surfaced the impact of the U.S.
military prostitution system on formation of the ‘Derivative
Amerasian Family Construct’ on first generation Amerasians; a
second, qualitative case study suggested the continued effect of the
prostitution systems' destructive impetuous on second generation
Amerasians. The intent of this current qualitative, multiple-case study
was to actively seek out second generation sex industry toilers. The
purpose was to focus further on this human phenomenon in the postbasing
and post-military prostitution system eras. As background, the
former military prostitution apparatus has transformed into a modern
dynamic of rampant sex tourism and prostitution nationwide. This is
characterized by hotel and resorts offering unrestricted carnal access,
urban and provincial brothels (casas), discos, bars and pickup clubs,
massage parlors, local barrio karaoke bars and street prostitution. A
small case study sample (N = 4) of female and male second
generation Amerasians were selected. Sample formation employed a
non-probability ‘snowball’ technique drawing respondents from the
notorious Angeles, Metro Manila, Olongapo City ‘AMO Amerasian
Triangle’ where most former U.S. military installations were sited
and modern sex tourism thrives. A six-month study and analysis of
in-depth interviews of female and male sex laborers, their families
and peers revealed a litany of disturbing, and troublesome
experiences. Results showed profiles of debilitating human poverty,
history of family disorganization, stigmatization, social
marginalization and the ghost of the military prostitution system and
its harmful legacy on Amerasian family units. Emerging were testimonials of wayward young people ensnared in a maelstrom of
deep economic deprivation, familial dysfunction, psychological
desperation and societal indifference. The paper recommends that
more study is needed and implications of unstudied psychosocial and
socioeconomic experiences of distressed younger generations of
military Amerasians require specific research. Heretofore apathetic or
disengaged U.S. institutions need to confront the issue and formulate
activist and solution-oriented social welfare, human services and
immigration easement policies and alternatives. These institutions
specifically include academic and social science research agencies,
corporate foundations, the U.S. Congress, and Departments of State,
Defense and Health and Human Services, and Homeland Security
(i.e. Citizen and Immigration Services) It is them who continue to
endorse a laissez-faire policy of non-involvement over the entire
Filipino Amerasian question. Such apathy, the paper concludes,
relegates this consequential but neglected blood progeny to the status
of humiliating destitution and exploitation. Amerasians; thus, remain
entrapped in their former colonial, and neo-colonial habitat.
Ironically, they are unwitting victims of a U.S. American homeland
that fancies itself geo-politically as a strong and strategic military
treaty ally of the Philippines in the Western Pacific.
Abstract: Although there has been a growing interest in the
hybrid free-space optical link and radio frequency FSO/RF
communication system, the current literature is limited to results
obtained in moderate or cold environment. In this paper, using a soft
switching approach, we investigate the effect of weather
inhomogeneities on the strength of turbulence hence the channel
refractive index under Qatar harsh environment and their influence
on the hybrid FSO/RF availability. In this approach, either FSO/RF
or simultaneous or none of them can be active. Based on soft
switching approach and a finite state Markov Chain (FSMC) process,
we model the channel fading for the two links and derive a
mathematical expression for the outage probability of the hybrid
system. Then, we evaluate the behavior of the hybrid FSO/RF under
hazy and harsh weather. Results show that the FSO/RF soft switching
renders the system outage probability less than that of each link
individually. A soft switching algorithm is being implemented on
FPGAs using Raptor code interfaced to the two terminals of a
1Gbps/100 Mbps FSO/RF hybrid system, the first being implemented
in the region. Experimental results are compared to the above
simulation results.
Abstract: The application of cold Radio-Frequency (RF) plasma
in the conservation of cultural heritage became important in the last
decades due to the positive results obtained in decontamination
treatments. This paper presents an equipment especially designed for cold RF
plasma application on paper documents, developed within a research
project. The equipment consists in two modules: the first one is
designed for decontamination and cleaning treatments of any type of
paper supports, while the second one can be used for coating friable
papers with adequate polymers, for protection purposes. All these
operations are carried out in cold radio-frequency plasma, working in
gaseous nitrogen, at low pressure. In order to optimize the equipment parameters ancient paper
samples infested with microorganisms have been treated in nitrogen
plasma and the decontamination effects, as well as changes in surface
properties (color, pH) were assessed. The microbiological analysis
revealed complete decontamination at 6 minutes treatment duration;
only minor modifications of the surface pH were found and the
colorimetric analysis showed a slight yellowing of the support.
Abstract: The LSTF experiment simulating the SGTR accident at
the Mihama Unit-2 reactor is analyzed using the RELAP5/MOD3.3
code. In the accident, and thus in the experiment, the ECC water was
injected not only into the cold legs but into the upper plenum. Overall
transients during the experiment such as pressures and fluid
temperatures are simulated well by the code. The cold-leg fluid
temperatures are shown to decrease if the upper plenum injection
system is connected to the cold leg. It is found that the cold-leg fluid
temperatures also decrease if the upper-plenum injection is not used
and the cold-leg injection alone is actuated.
Abstract: In this work, the plastic behaviour of cold-rolled zinc
coated dual-phase steel sheets DP600 and DP800 grades is firstly
investigated with the help of uniaxial, hydraulic bulge and Forming
Limit Curve (FLC) tests. The uniaxial tensile tests were performed in
three angular orientations with respect to the rolling direction to
evaluate the strain-hardening and plastic anisotropy. True stressstrain
curves at large strains were determined from hydraulic bulge
testing and fitted to a work-hardening equation. The limit strains are
defined at both localized necking and fracture conditions according to
Nakajima’s hemispherical punch procedure. Also, an elasto-plastic
localization model is proposed in order to predict strain and stress
based forming limit curves. The investigated dual-phase sheets
showed a good formability in the biaxial stretching and drawing FLC
regions. For both DP600 and DP800 sheets, the corresponding
numerical predictions overestimated and underestimated the
experimental limit strains in the biaxial stretching and drawing FLC
regions, respectively. This can be attributed to the restricted failure
necking condition adopted in the numerical model, which is not
suitable to describe the tensile and shear fracture mechanisms in
advanced high strength steels under equibiaxial and biaxial stretching
conditions.
Abstract: Low Temperature Matrix Isolation - Electron
Paramagnetic Resonance (LTMI-EPR) Spectroscopy was utilized to
identify the species of iron oxide nanoparticles generated during the
oxidative pyrolysis of 1-methylnaphthalene (1-MN). The otherwise
gas-phase reactions of 1--MN were impacted by a polypropylenimine
tetra-hexacontaamine dendrimer complexed with iron (III) nitrate
nonahydrate diluted in air under atmospheric conditions. The EPR
fine structure of Fe (III)2O3 nanoparticles clusters, characterized by gfactors
of 2.00, 2.28, 3.76 and 4.37 were detected on a cold finger
maintained at 77 K after accumulation over a multitude of
experiments. Additionally, a high valence Fe (IV) paramagnetic
intermediate and superoxide anion-radicals, O2•- adsorbed on
nanoparticle surfaces in the form of Fe (IV) --- O2•- were detected
from the quenching area of Zone 1 in the gas-phase.
Abstract: The effects of flame-holder position, the ratio of flame
holder diameter to combustion chamber diameter and injection angle
on fuel propulsive droplets sizing and effective mass fraction have
been studied by a cold flow. We named the mass of fuel vapor inside
the flammability limit as the effective mass fraction. An empty
cylinder as well as a flame-holder which are a simulator for duct
combustion has been considered. The airflow comes into the cylinder
from one side and injection operation will be done by four nozzles
which are located on the entrance of cylinder. To fulfill the
calculations a modified version of KIVA-3V code which is a
transient, three-dimensional, multiphase, multi component code for
the analysis of chemically reacting flows with sprays, is used.
Abstract: In present global scenario, aluminum alloys are
coining the attention of many innovators as competing structural
materials for automotive and space applications. Comparing to other
challenging alloys, especially, 7xxx series aluminum alloys have
been studied seriously because of benefits such as moderate strength;
better deforming characteristics and affordable cost. It is expected
that substitution of aluminum alloys for steels will result in great
improvements in energy economy, durability and recyclability.
However, it is necessary to improve the strength and the formability
levels at low temperatures in aluminum alloys for still better
applications. Aluminum–Zinc–Magnesium with or without other
wetting agent denoted as 7XXX series alloys are medium strength
heat treatable alloys. In addition to Zn, Mg as major alloying
additions, Cu, Mn and Si are the other solute elements which
contribute for the improvement in mechanical properties by suitable
heat treatment process. Subjecting to suitable treatments like age
hardening or cold deformation assisted heat treatments; known as low
temperature thermomechanical treatments (LTMT) the challenging
properties might be incorporated. T6 is the age hardening or
precipitation hardening process with artificial aging cycle whereas T8
comprises of LTMT treatment aged artificially with X% cold
deformation. When the cold deformation is provided after solution
treatment, there is increase in hardness related properties such as
wear resistance, yield and ultimate strength, toughness with the
expense of ductility. During precipitation hardening both hardness
and strength of the samples are increasing. The hardness value may
further improve when room temperature deformation is positively
supported with age hardening known as thermomechanical treatment.
It is intended to perform heat treatment and evaluate hardness, tensile
strength, wear resistance and distribution pattern of reinforcement in
the matrix. 2 to 2.5 and 3 to 3.5 times increase in hardness is reported
in age hardening and LTMT treatments respectively as compared to
as-cast composite. There was better distribution of reinforcements in
the matrix, nearly two fold increase in strength levels and up to 5
times increase in wear resistance are also observed in the present
study.
Abstract: In this paper air quality conditions in Makkah and
Leeds are compared. These two cities have totally different climatic
conditions. Makkah climate is characterised as hot and dry (arid)
whereas that of Leeds is characterised as cold and wet (temperate).
This study uses air quality data from 2012 collected in Makkah,
Saudi Arabia and Leeds, UK. The concentrations of all pollutants,
except NO are higher in Makkah. Most notable, the concentrations of
PM10 are much higher in Makkah than in Leeds. This is probably due
to the arid nature of climatic conditions in Makkah and not solely due
to anthropogenic emission sources, otherwise like PM10 some of the
other pollutants, such as CO, NO, and SO2 would have shown much
greater difference between Leeds and Makkah. Correlation analysis is
performed between different pollutants at the same site and the same
pollutants at different sites. In Leeds the correlation between PM10
and other pollutants is significantly stronger than in Makkah. Weaker
correlation in Makkah is probably due to the fact that in Makkah
most of the gaseous pollutants are emitted by combustion processes,
whereas most of the PM10 is generated by other sources, such as
windblown dust, re-suspension, and construction activities. This is in
contrast to Leeds where all pollutants including PM10 are
predominantly emitted by combustions, such as road traffic.
Furthermore, in Leeds frequent rains wash out most of the
atmospheric particulate matter and suppress re-suspension of dust.
Temporal trends of various pollutants are compared and discussed.
This study emphasises the role of climatic conditions in managing air
quality, and hence the need for region-specific controlling strategies
according to the local climatic and meteorological conditions.