Abstract: Sedimentation of magnetorheological (MR) fluid affects its working. MR fluid is a smart fluid that has unique qualities such as quick responsiveness and easy controllability. It is used in the MR damper, MR brake, and MR clutch. In this work effect of sedimentation on torque transmission in the shear mode operated MR clutch is investigated. A test rig is developed to test the impact of sedimentation on torque transmission in the MR clutch. Torque transmission capability of MR clutch has been measured under two conditions to confirm the result of sedimentation. The first experiment is done just after filling and the other after one week. It has been observed that transmission torque is decreased after sedimentation. Hence sedimentation affects the working of the MR clutch.
Abstract: Vehicular emission is the key source of air pollution in the urban environment. This includes both fine particles (PM2.5) and coarse particulate matters (PM10). However, particulate matter emissions from road traffic comprise emissions from exhaust tailpipe and emissions due to wear and tear of the vehicle part such as brake, tire and clutch and re-suspension of dust (non-exhaust emission). This study estimates the share of the two sources of pollutant particle emissions from on-roadside vehicles in the Addis Ababa municipality, Ethiopia. To calculate its share, two methods were applied; the exhaust-tailpipe emissions were calculated using the Europeans emission inventory Tier II method and Tier I for the non-exhaust emissions (like vehicle tire wear, brake, and road surface wear). The results show that of the total traffic-related particulate emissions in the city, 63% emitted from vehicle exhaust and the remaining 37% from non-exhaust sources. The annual roads transport exhaust emission shares around 2394 tons of particles from all vehicle categories. However, from the total yearly non-exhaust particulate matter emissions’ contribution, tire and brake wear shared around 65% and 35% emanated by road-surface wear. Furthermore, vehicle tire and brake wear were responsible for annual 584.8 tons of coarse particles (PM10) and 314.4 tons of fine particle matter (PM2.5) emissions in the city whereas surface wear emissions were responsible for around 313.7 tons of PM10 and 169.9 tons of PM2.5 pollutant emissions in the city. This suggests that non-exhaust sources might be as significant as exhaust sources and have a considerable contribution to the impact on air quality.
Abstract: Proposing an appropriate control strategy is an effective and practical way to address the overheat problems of the wet multi-plate clutch in Direct Shift Gearbox under the long-time creeping condition. To do so, the temperature variation of the wet multi-plate clutch is investigated firstly by establishing a thermal resistance model for the gearbox cooling system. To calculate the generated heat flux and predict the clutch temperature precisely, the friction torque model is optimized by introducing an improved friction coefficient, which is related to the pressure, the relative speed and the temperature. After that, the heat transfer model and the reasonable friction torque model are employed by the vehicle powertrain model to construct a comprehensive co-simulation model for the Direct Shift Gearbox (DSG) vehicle. A creeping control strategy is then proposed and, to evaluate the vehicle performance, the safety temperature (250 ℃) is particularly adopted as an important metric. During the creeping process, the temperature of two clutches is always under the safety value (250 ℃), which demonstrates the effectiveness of the proposed control strategy in avoiding the thermal failures of clutches.
Abstract: Power transmitted from the engine to the final drive where useful work is applied through a system consisting of a gearbox, clutch, drive shaft and a differential in the rear-wheel-drive automobiles. It is well-known that the steel drive shaft is usually manufactured in two pieces to increase the fundamental bending natural frequency to ensure safe operation conditions. In this work, hybrid one-piece propeller shafts composed of carbon/epoxy and glass/epoxy composites have been designed for a rear wheel drive automobile satisfying three design specifications, such as static torque transmission capability, torsional buckling and the fundamental natural bending frequency. Hybridization of carbon and glass fibers is being studied to optimize the cost/performance requirements. Composites shaft materials with various fiber orientation angles and stacking sequences are being fabricated and analyzed using finite element analysis (FEA).
Abstract: This paper presents the static and cyclic stresses in combination with fatigue analysis resultant of loads applied on the friction discs usually utilized on industrial clutches. The material chosen to simulate the friction discs under load is aluminum. The numerical simulation was done by software COMSOLTM Multiphysics. The results obtained for static loads showed enough stiffness for both geometries and the material utilized. On the other hand, in the fatigue standpoint, failure is clearly verified, what demonstrates the importance of both approaches, mainly dynamical analysis. The results and the conclusion are based on the stresses on disc, counted stress cycles, and fatigue usage factor.
Abstract: This paper focuses on developing an estimation method of clutch drag torque in wet DCT. The modelling of clutch drag torque is investigated. As the main factor affecting the clutch drag torque, dynamic viscosity of oil is discussed. The paper proposes an estimation method of clutch drag torque based on recursive least squares by utilizing the dynamic equations of gear shifting synchronization process. The results demonstrate that the estimation method has good accuracy and efficiency.
Abstract: The automatic transmission (AT) is one of the most
important components of many automobile transmission systems. The
shift quality has a significant influence on the ride comfort of the
vehicle. During the AT shift process, the joint elements such as the
clutch and bands engage or disengage, linking sets of gears to create a
fixed gear ratio. Since these ratios differ between gears in a fixed gear
ratio transmission, the motion of the vehicle could change suddenly
during the shift process if the joint elements are engaged or disengaged
inappropriately, additionally impacting the entire transmission system
and increasing the temperature of connect elements.The objective was
to establish a system model for an AT powertrain using
Matlab/Simulink. This paper further analyses the effect of varying
hydraulic pressure and the associated impact on shift quality during
both engagment and disengagement of the joint elements, proving that
shift quality improvements could be achieved with appropriate
hydraulic pressure control.
Abstract: Organochlorine pesticides (OCPs) are known to be
persistent and bioaccumulative toxicants that may cause reproductive
impairments in wildlife as well as human. The current study uses the
snail-eating turtle Malayemys macrocephala, a long-lived animal
commonly distribute in rice field habitat in central part of Thailand,
as a sentinel to monitor OCP contamination in environment. The
nest soil, complete clutch of eggs, and blood of the turtle were
collected from agricultural areas in the Chao Phraya River Basin,
Thailand during the nesting season of 2007-2008. The novel
methods for tissue extraction by an accelerated solvent extractor
(ASE, for egg) and liquid-liquid extraction (for blood) have been
developed. The nineteen OCP residues were analyzed by gas
chromatography with micro-electron captured detector (GC-μECD).
The validated methods have met requirements of the AOAC
standard. The results indicated that significant amounts of OCPs are
still contaminated in nest soil and eggs of the turtle even though the
OCPs had been banned in this area for many years. This suggested
the potential risk to health of wildlife as well as human in the area.
Abstract: The feasibility of applying a simple and cost effective sliding friction testing apparatus to study the friction behaviour of a clutch facing material, effected by the variation of temperature and contact pressure, was investigated. It was found that the method used in this work was able to give a convenient and cost effective measurement of friction coefficients and their transitions of a clutch facing material. The obtained results will be useful for the development process of new facing materials.
Abstract: One of the best ways for achievement of conventional
vehicle changing to hybrid case is trustworthy simulation result and
using of driving realities. For this object, in this paper, at first sevendegree-
of-freedom dynamical model of vehicle will be shown. Then
by using of statically model of engine, gear box, clutch, differential,
electrical machine and battery, the hybrid automobile modeling will
be down and forward simulation of vehicle for pedals to wheels
power transformation will be obtained. Then by design of a fuzzy
controller and using the proper rule base, fuel economy and
regenerative braking will be marked. Finally a series of
MATLAB/SIMULINK simulation results will be proved the
effectiveness of proposed structure.
Abstract: In this study, the two dimensional heat conduction
problem for the dry friction clutch disc is modeled mathematically
analysis and is solved numerically using finite element method, to
determine the temperature field when band contacts occurs between
the rubbing surfaces during the operation of an automotive clutch.
Temperature calculation have been made for contact area of different
band width and the results obtained compared with these attained
when complete contact occurs. Furthermore, the effects of slipping
time and sliding velocity function are investigated as well. Both
single and repeated engagements made at regular interval are
considered.