Abstract: Scrubbing by a liquid spraying is one of the most
effective processes used for removal of fine particles and soluble
gas pollutants (such as SO2, HCl, HF) from the flue gas. There are
many configurations of scrubbers designed to provide contact
between the liquid and gas stream for effectively capturing
particles or soluble gas pollutants, such as spray plates, packed bed
towers, jet scrubbers, cyclones, vortex and venturi scrubbers. The
primary function of venturi scrubber is the capture of fine particles
as well as HCl, HF or SO2 removal with effect of the flue gas
temperature decrease before input to the absorption column. In this
paper, sulfur dioxide (SO2) from flue gas was captured using new
design replacing venturi scrubber (1st degree of wet scrubbing).
The flue gas was prepared by the combustion of the carbon
disulfide solution in toluene (1:1 vol.) in the flame in the reactor.
Such prepared flue gas with temperature around 150°C was
processed in designed laboratory O-element scrubber. Water was
used as absorbent liquid. The efficiency of SO2 removal, pressure
drop and temperature drop were measured on our experimental
device. The dependence of these variables on liquid-gas ratio was
observed. The average temperature drop was in the range from
150°C to 40°C. The pressure drop was increased with increasing of
a liquid-gas ratio, but no too much as for the common venturi
scrubber designs. The efficiency of SO2 removal was up to 70 %.
The pressure drop of our new designed wet scrubber is similar to
commonly used venturi scrubbers; nevertheless the influence of
amount of the liquid on pressure drop is not so significant.
Abstract: The problem of toughening in brittle materials
reinforced by fibers is complex, involving all of the mechanical
properties of fibers, matrix and the fiber/matrix interface, as well as
the geometry of the fiber. Development of new numerical methods
appropriate to toughening simulation and analysis is necessary. In
this work, we have performed simulations and analysis of toughening
in brittle matrix reinforced by randomly distributed fibers by means
of the discrete elements method. At first, we put forward a
mechanical model of toughening contributed by random fibers. Then
with a numerical program, we investigated the stress, damage and
bridging force in the composite material when a crack appeared in the
brittle matrix. From the results obtained, we conclude that: (i) fibers
of high strength and low elasticity modulus are beneficial to
toughening; (ii) fibers of relatively high elastic modulus compared to
the matrix may result in substantial matrix damage due to spalling
effect; (iii) employment of high-strength synthetic fibers is a good
option for toughening. We expect that the combination of the discrete
element method (DEM) with the finite element method (FEM) can
increase the versatility and efficiency of the software developed. The
present work can guide the design of ceramic composites of high
performance through the optimization of the parameters.
Abstract: The thermal control in many systems is widely
accomplished applying mixed convection process due to its low cost,
reliability and easy maintenance. Typical applications include the
aircraft electronic equipment, rotating-disc heat exchangers, turbo
machinery, and nuclear reactors, etc. Natural convection in an inclined
square enclosure heated via wall heater has been studied numerically.
Finite volume method is used for solving momentum and energy
equations in the form of stream function–vorticity. The right and left
walls are kept at a constant temperature, while the other parts are
adiabatic. The range of the inclination angle covers a whole revolution.
The method is validated for a vertical cavity. A general power law
dependence of the Nusselt number with respect to the Rayleigh
number with the coefficient and exponent as functions of the
inclination angle is presented. For a fixed Rayleigh number, the
inclination angle increases or decreases is found.
Abstract: In this paper, effects of using Alumina-water
nanofluid on the rate of heat transfer have been investigated
numerically. Physical model is a square enclosure with insulated top
and bottom horizontal walls, while the vertical walls are kept at
different constant temperatures. Two appropriate models are used to
evaluate the viscosity and thermal conductivity of nanofluid. The
governing stream-vorticity equations are solved using a second order
central finite difference scheme, coupled to the conservation of mass
and energy. The study has been carried out for the Richardson
number 0.1 to 10 and the solid volume fraction 0 to 0.04. Results are
presented by isotherms lines, average Nusselt number and normalized
Nusselt number in different range of φ and Ri for forced, combined
and natural convection dominated regime. It is found that higher heat
transfer rate is predicted when the effects of nanoparticle is taken into
account.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: Photonic Crystal Fibers (PCFs) can be used in optical
communications as transmission lines. For this reason, the PCFs with
low confinement loss, low chromatic dispersion, and low nonlinear
effects are highly suitable transmission media. In this paper, we
introduce a new design of index-guiding nanostructured photonic
crystal fiber (IG-NPCF) with ultra-low chromatic dispersion, low
nonlinearity effects, and low confinement loss. Relatively low
dispersion is achieved in the wavelength range of 1200 to 1600nm
using the proposed design. According to the new structure of
nanostructured PCF presented in this study, the chromatic dispersion
slope is -30(ps/km.nm) and the confinement loss reaches below 10-7
dB/km. While in the wavelength range mentioned above at the same
time an effective area of more than 50.2μm2 is obtained.
Abstract: In this paper, the dynamic characteristics of a threelobe
journal bearing lubricated with micropolar fluids are determined
by the linear stability theory. Lubricating oil containing additives and
contaminants is modelled as micropolar fluid. The modified
Reynolds equation is obtained using the micropolar lubrication theory
.The finite difference technique has been used to determine the
solution of the modified Reynolds equation. The dynamic
characteristics in terms of stiffness, damping coefficients, the critical
mass and whirl ratio are determined for various values of size of
material characteristic length and the coupling number. The
computed results show that the three-lobe bearing lubricated with
micropolar fluid exhibits better stability compared with that
lubricated with Newtonian fluid. According to the results obtained,
the effect of the parameter micropolar fluid is remarkable on the
dynamic characteristics and stability of the three-lobe bearing.
Abstract: A finite difference/front tracking method is used to
study the motion of three-dimensional deformable drops suspended in
plane Poiseuille flow at non-zero Reynolds numbers. A parallel
version of the code was used to study the behavior of suspension on a
reasonable grid resolution (grids). The viscosity and density of drops
are assumed to be equal to that of the suspending medium. The effect
of the Reynolds number is studied in detail. It is found that drops
with small deformation behave like rigid particles and migrate to an
equilibrium position about half way between the wall and the
centerline (the Segre-Silberberg effect). However, for highly
deformable drops there is a tendency for drops to migrate to the
middle of the channel, and the maximum concentration occurs at the
centerline. The effective viscosity of suspension and the fluctuation
energy of the flow across the channel increases with the Reynolds
number of the flow.
Abstract: reliability-based methodology for the assessment
and evaluation of reinforced concrete (R/C) structural elements of
concrete structures is presented herein. The results of the reliability
analysis and assessment for R/C structural elements were verified by
the results obtained through deterministic methods. The outcomes of
the reliability-based analysis were compared against currently
adopted safety limits that are incorporated in the reliability indices
β’s, according to international standards and codes. The methodology
is based on probabilistic analysis using reliability concepts and
statistics of the main random variables that are relevant to the subject
matter, and for which they are to be used in the performance-function
equation(s) associated with the structural elements under study.
These methodology techniques can result in reliability index β, which
is commonly known as the reliability index or reliability measure
value that can be utilized to assess and evaluate the safety, human
risk, and functionality of the structural component. Also, these
methods can result in revised partial safety factor values for certain
target reliability indices that can be used for the purpose of
redesigning the R/C elements of the building and in which they could
assist in considering some other remedial actions to improve the
safety and functionality of the member.
Abstract: The effect of various humidities on process yields and
degrees of crystallinity for spray-dried powders from spray drying of
lactose with humid air in a straight-through system have been
studied. It has been suggested by Williams–Landel–Ferry kinetics
(WLF) that a higher particle temperature and lower glass-transition
temperature would increase the crystallization rate of the particles
during the spray-drying process. Freshly humidified air produced by
a Buchi-B290 spray dryer as a humidifier attached to the main spray
dryer decreased the particle glass-transition temperature (Tg), while
allowing the particle temperature (Tp) to reach higher values by using
an insulated drying chamber. Differential scanning calorimetry
(DSC) and moisture sorption analysis were used to measure the
degree of crystallinity for the spray-dried lactose powders. The
results showed that higher Tp-Tg, as a result of applying humid air,
improved the process yield from 21 ± 4 to 26 ± 2% and crystallinity
of the particles by decreasing the latent heat of crystallization from
43 ± 1 to 30 ± 11 J/g and the sorption peak height from 7.3 ± 0.7% to
6 ± 0.7%.
Abstract: A simple multi-wavelength passively Q-switched
Erbium-doped fiber laser (EDFL) is demonstrated using low cost
multi-walled carbon nanotubes (MWCNTs) based saturable absorber
(SA), which is prepared using polyvinyl alcohol (PVA) as a host
polymer. The multi-wavelength operation is achieved based on
nonlinear polarization rotation (NPR) effect by incorporating 50 m
long photonic crystal fiber (PCF) in the ring cavity. The EDFL
produces a stable multi-wavelength comb spectrum for more than 14
lines with a fixed spacing of 0.48 nm. The laser also demonstrates a
stable pulse train with the repetition rate increases from 14.9 kHz to
25.4 kHz as the pump power increases from the threshold power of
69.0 mW to the maximum pump power of 133.8 mW. The minimum
pulse width of 4.4 μs was obtained at the maximum pump power of
133.8 mW while the highest energy of 0.74 nJ was obtained at pump
power of 69.0 mW.
Abstract: FMEA has been used for several years and proved its efficiency for system’s risk analysis due to failures. Risk priority number found in FMEA is used to rank failure modes that may occur in a system. There are some guidelines in the literature to assign the values of FMEA components known as Severity, Occurrence and Detection. This paper propose a method to assign the value for occurrence in more realistic manner representing the state of the system under study rather than depending totally on the experience of the analyst. This method uses the hazard function of a system to determine the value of occurrence depending on the behavior of the hazard being constant, increasing or decreasing.
Abstract: In this study, a liquid phase microextraction by hollow fiber (HF-LPME) combined with high performance liquid chromatography-UV detector was applied to preconcentrate and determine trace levels of Cyproheptadine in human urine and plasma samples. Cyproheptadine was extracted from 10 mL alkaline aqueous solution (pH: 9.81) into an organic solvent (n-octnol) which was immobilized in the wall pores of a hollow fiber. Then was back-extracted into an acidified aqueous solution (pH: 2.59) located inside the lumen of the hollow fiber. This method is simple, efficient and cost-effective. It is based on pH gradient and differences between two aqueous phases. In order to optimize the HF-LPME some affecting parameters including the pH of donor and acceptor phases, the type of organic solvent, ionic strength, stirring rate, extraction time and temperature were studied and optimized. Under optimal conditions enrichment factor, limit of detection (LOD) and relative standard deviation (RSD(%), n=3) were up to 112, 15 μg.L−1 and 2.7, respectively.
Abstract: Combustion phenomenon will be accomplished
effectively by the development of low emission combustor. One of the
significant factors influencing the entire Combustion process is the
mixing between a swirling angular jet (Primary Air) and the
non-swirling inner jet (fuel). To study this fundamental flow, the
chamber had to be designed in such a manner that the combustion
process to sustain itself in a continuous manner and the temperature of
the products is sufficiently below the maximum working temperature
in the turbine. This study is used to develop the effective combustion
with low unburned combustion products by adopting the concept of
high swirl flow and motility of holes in the secondary chamber. The
proper selection of a swirler is needed to reduce emission which can be
concluded from the emission of Nox and CO2. The capture of CO2 is
necessary to mitigate CO2 emissions from natural gas. Thus the
suppression of unburned gases is a meaningful objective for the
development of high performance combustor without affecting turbine
blade temperature.
Abstract: PAN nanofibers reinforced with amine functionalized
carbon nanotubes. The effect of amine functionalization and the
effect of concentration of CNT on the conductivity and mechanical
and morphological properties of composite nanofibers were
examined. 1%CNT-NH2 loaded PAN/CNT nanofiber showed the best
mechanical properties. Conductivity increased with the incorporation
of carbon nanotubes. While an increase of concentration of CNT
increases the diameter of nanofiber, the use of functionalized CNT
results to decrease of diameter of nanofiber.
Abstract: This research investigates the distribution of food
demand for animal food and the optimum amount of that food
production at minimum cost. The data consist of customer purchase
orders for the food of laying hens, price of food for laying hens, cost
per unit for the food inventory, cost related to food of laying hens in
which the food is out of stock, such as fine, overtime, urgent
purchase for material. They were collected from January, 1990 to
December, 2013 from a factory in Nakhonratchasima province. The
collected data are analyzed in order to explore the distribution of the
monthly food demand for the laying hens and to see the rate of
inventory per unit. The results are used in a stochastic linear
programming model for aggregate planning in which the optimum
production or minimum cost could be obtained. Programming
algorithms in MATLAB and tools in Linprog software are used to get
the solution. The distribution of the food demand for laying hens and
the random numbers are used in the model. The study shows that the
distribution of monthly food demand for laying has a normal
distribution, the monthly average amount (unit: 30 kg) of production
from January to December. The minimum total cost average for 12
months is Baht 62,329,181.77. Therefore, the production planning
can reduce the cost by 14.64% from real cost.
Abstract: This paper is an attempt to describe some of the results that had been found through a journey of study in the field of particle physics. This study consists of two parts, one about the measurement of the cross section of the decay of the Z particle in two electrons, and the other deals with the measurement of the cross section of the multi-photon absorption process using a beam of Laser in the Liquid Argon Time Projection Chamber.
The first part of the paper concerns the results based on the analysis of a data sample containing 8120 ee candidates to reconstruct the mass of the Z particle for each event where each event has an ee pair with PT(e) > 20GeV, and η(e) < 2.5. Monte Carlo templates of the reconstructed Z particle were produced as a function of the Z mass scale. The distribution of the reconstructed Z mass in the data was compared to the Monte Carlo templates, where the total cross section is calculated to be equal to 1432pb.
The second part concerns the Liquid Argon Time Projection Chamber, LAr TPC, the results of the interaction of the UV Laser, Nd-YAG with λ= 266mm, with LAr and through the study of the multi-photon ionization process as a part of the R&D at Bern University. The main result of this study was the cross section of the process of the multi-photon ionization process of the LAr, σe = 1.24±0.10stat±0.30sys.10 -56cm4.
Abstract: Economic growth always correlate positively with the
magnitude of the unemployment rate. This is caused by labor which
one of important variable to keep growth in the real sector of the
region. Meanwhile, the economic structure in districts of Jember
showed an increase of economic activity began to shift towards the
industrial sector and some other economic sectors, so they have an
affects to considerations for policy makers to increase economic
growth in Jember as an autonomous region in East Java Province. At
the fact, SMEs is among the factors driving economic growth in the
region. This is shown by the high amount of SMEs. However,
employment in the sector grew slightly slowed. It is caused by a lack
of productivity in SMEs. Through the analysis of the transformation of
economic structure theory, and the theory of Triple Helix using
descriptive analytical method Location Quotient and Shift - Share,
found that the results of the economic structure in Jember slowly
shifting from the agricultural sector to the industrial sector, because it
is dominated by trade sector, hotel and restaurant sector. In addition,
SMEs is the potential sector of economic growth in Jember. While to
maximizing role and functions of the institution's Research and
Development Center of SMEs, there are three points to be known, that
are Business Landscape, Business Architecture and Value Added.
Abstract: The objectives of the present study were to estimate the microbial-N flow to the small intestine and to predict the digestible organic matter intake (DOMI) in grazing Karayaka sheep based on urinary excretion of purine derivatives (xanthine, hypoxanthine, uric acid, and allantoin) by the use of spot urine sampling under field conditions. In the trial, 10 Karayaka sheep from 2 to 3 years of age were used. The animals were grazed in a pasture for ten months and fed with concentrate and vetch plus oat hay for the other two months (January and February) indoors. Highly significant linear and cubic relationships (P
Abstract: The miniaturization of gas turbines promises many advantages. Miniature gas turbines can be used for local power generation or the propulsion of small aircraft, such as UAV and MAV. However, experience shows that the miniaturization of conventional gas turbines, which are optimized at their current large size, leads to a substantial loss of efficiency and performance at smaller scales. This may be due to a number of factors, such as the Reynolds-number effect, the increased heat transfer, and manufacturing tolerances. In the present work, we focus on computational investigations of the Reynolds number effect and the wall heat transfer on the performance of axial compressor during its size change. The NASA stage 35 compressor is selected as the configuration in this study and computational fluid dynamics (CFD) is used to carry out the miniaturization process and simulations. We perform parameter studies on the effect of Reynolds number and wall thermal conditions. Our results indicate a decrease of efficiency, if the compressor is miniaturized based on its original geometry due to the increase of viscous effects. The increased heat transfer through wall has only a small effect and will actually benefit compressor performance based on our study.