Abstract: Solutions for the temperature profile around a moving
heat source are obtained using both analytic and finite element
(FEM) methods. Analytic and FEM solutions are applied to study the
temperature profile in welding. A moving heat source is represented
using both point heat source and uniform distributed disc heat source
models. Analytic solutions are obtained by solving the partial
differential equation for energy conservation in a solid, and FEM
results are provided by simulating welding using the ANSYS
software. Comparison is made for quasi steady state conditions. The
results provided by the analytic solutions are in good agreement with
results obtained by FEM.
Abstract: Knee joint forces are available by in vivo measurement
using an instrumented knee prosthesis for small to moderate knee
flexion but not for high flexion yet. We created a 2D mathematical
model of the lower limb incorporating several new features such as a
patello-femoral mechanism, a thigh-calf contact at high knee flexion
and co-contracting muscles' force ratio, then used it to determine knee
joint forces arising from high knee flexions in four kneeling
conditions: rising with legs in parallel, with one foot forward, with or
without arm use. With arms used, the maximum values of knee joint
force decreased to about 60% of those with arms not used. When rising
with one foot forward, if arms are not used, the forward leg sustains a
force as large as that sustained when rising with legs parallel.
Abstract: Air quality studies were carried out in the towns of
Putrajaya, Petaling Jaya and Nilai in the Malaysian Peninsular. In this
study, the variations of Ozone (O3) concentrations over a four year
period (2008-2011) were investigated using data obtained from the
Malaysian Department of the Environment (DOE). This study aims to
identify and describe the daily and monthly variations of O3
concentrations at the monitoring sites mentioned. The SPPS program
(Statistical Package for the Social Science) was used to analyze this
data in order to obtain the variations of O3 and also to clarify the
relationship between the stations. The findings of the study revealed
that the highest concentration of O3 occurred during the midday and
afternoon (between 13:00-15:00 hrs). The comparison between
stations also showed that highest O3 concentrations were recorded in
Putrajaya. The comparisons of average and maximum concentrations
of O3 for the three stations showed that the strongest significant
correlation was recorded in the Petaling Jaya station with the value
R2= 0.667. Results from this study indicate that in the urban areas of
Peninsular Malaysia, the concentration of O3 depends on the
concentration of NOx. Furthermore, HYSPLIT back trajectories
(-72h) indicated that air-mass transport patterns can also influence the
O3 concentration in the areas studied.
Abstract: Currently searching through internet is very popular especially in a field of academic. A huge of educational information such as research papers are overload for user. So community-base web sites have been developed to help user search information more easily from process of customizing a web site to need each specifies user or set of user. In this paper propose to use association rule analyze the community group on research paper bookmarking. A set of design goals for community group frameworks is developed and discussed. Additionally Researcher analyzes the initial relation by using association rule discovery between the antecedent and the consequent of a rule in the groups of user for generate the idea to improve ranking search result and development recommender system.
Abstract: In this work, study the location of interface in a stirred vessel with Rushton impeller by computational fluid dynamic was presented. To modeling rotating the impeller, sliding mesh (SM) technique was used and standard k-ε model was selected for turbulence closure. Mean tangential, radial and axial velocities and also turbulent kinetic energy (k) and turbulent dissipation rate (ε) in various points of tank was investigated. Results show sensitivity of system to location of interface and radius of 7 to 10cm for interface in the vessel with existence characteristics cause to increase the accuracy of simulation.
Abstract: Coarse and fine particulate matter were collected at a
residential area at Vashi, Navi Mumbai and the filter samples were
analysed for trace elements using PIXE technique. The trend of
particulate matter showed higher concentrations during winter than
the summer and monsoon concentration levels. High concentrations
of elements related to soil and sea salt were found in PM10 and
PM2.5. Also high levels of zinc and sulphur found in the particulates
of both the size fractions. EF analysis showed enrichment of Cu, Cr
and Mn only in the fine fraction suggesting their origin from
anthropogenic sources. The EF value was observed to be maximum
for As, Pb and Zn in the fine particulates. However, crustal derived
elements showed very low EF values indicating their origin from
soil. The PCA based multivariate studies identified soil, sea salt,
combustion and Se sources as common sources for coarse and
additionally an industrial source has also been identified for fine
particles.
Abstract: Using a methodology grounded in business process
change theory, we investigate the critical success factors that affect
ERP implementation success in United States and India.
Specifically, we examine the ERP implementation at two case study
companies, one in each country. Our findings suggest that certain
factors that affect the success of ERP implementations are not
culturally bound, whereas some critical success factors depend on the
national culture of the country in which the system is being
implemented. We believe that the understanding of these critical
success factors will deepen the understanding of ERP
implementations and will help avoid implementation mistakes,
thereby increasing the rate of success in culturally different contexts.
Implications of the findings and future research directions for both
academicians and practitioners are also discussed.
Abstract: Design and land use are closely linked to the
energy efficiency levels for an urban area. The current city
planning practice does not involve an effective land useenergy
evaluation in its 'blueprint' urban plans. The study
proposed an appraisal method that can be embedded in GIS
programs using five planning criteria as how far a planner can
give away from the planning principles (criteria) for the most
energy output s/he can obtain. The case of Balcova, a district
in the Izmir Metropolitan area, is used conformingly for
evaluating the proposed master plan and the geothermal
energy (heating only) use for the concern district.
If the land use design were proposed accordingly at-most
energy efficiency (a 30% obtained), mainly increasing the
density around the geothermal wells and also proposing more
mixed use zones, we could have 17% distortion (infidelity to
the main planning principles) from the original plan. The
proposed method can be an effective tool for planners as
simulation media, of which calculations can be made by GIS
ready tools, to evaluate efficiency levels for different plan
proposals, letting to know how much energy saving causes
how much deviation from the other planning ideals. Lower
energy uses can be possible for different land use proposals
for various policy trials.
Abstract: In this research, a part of Aghche basin in Isfahan
province with an area about 2000 hectars, was chosen to be obtain
curve number coefficient runoff and W indicator in second Cook
method By using aerial photos 1968 and 1995, the satellite data of
the IRS in 2008. Then the process of land use changes in the period
of study and its effect on the changes of curve number (CN), W
indicator and surface runoff coefficient (C) of the basin was
investigated. These results showed that on the track of these land use
changes the weight averages curve number (CN), surface runoff
coefficient (C) and W indicator of the basin were increased to 0.92,
0.02 and 0.78 unit in the first period of study and 1.18, 0.03, 0.99
Unit in the second period of study respectively.
Abstract: Tungsten trioxide has been prepared by using P-PTA
as a precursor on alumina substrates by spin coating method.
Palladium introduced on WO3 film via electrolysis deposition by
using palladium chloride as catalytic precursor. The catalytic
precursor was introduced on the series of films with different
morphologies. X-ray diffractometry (XRD), Scanning electron
microscopy (SEM) and XPS were applied to analyze structure and
morphology of the fabricated thin films. Then we measured variation
of samples- electrical conductivity of pure and Pd added films in air
and diluted hydrogen. Addition of Pd resulted in a remarkable
improvement of the hydrogen sensing properties of WO3 by detection
of Hydrogen below 1% at room temperature. Also variation of the
electrical conductivity in the presence of diluted hydrogen revealed
that response of samples depends rather strongly on the palladium
configuration on the surface.
Abstract: Wind turbines with double output induction
generators can operate at variable speed permitting conversion
efficiency maximization over a wide range of wind velocities. This
paper presents the performance analysis of a wind driven double
output induction generator (DOIG) operating at varying shafts speed.
A periodic transient state analysis of DOIG equipped with two
converters is carried out using a hybrid induction machine model.
This paper simulates the harmonic content of waveforms in various
points of drive at different speeds, based on the hybrid model
(dqabc). Then the sinusoidal and trapezoidal pulse-width–modulation
control techniques are used in order to improve the power factor of
the machine and to weaken the injected low order harmonics to the
supply. Based on the frequency spectrum, total harmonics distortion,
distortion factor and power factor. Finally advantages of sinusoidal
and trapezoidal pulse width modulation techniques are compared.
Abstract: Environmental aspects plays a central role in environmental management system (EMS) because it is the basis for the identification of an organization-s environmental targets. The
existing methods for the assessment of environmental aspects are grouped into three categories: risk assessment-based (RA-based),
LCA-based and criterion-based methods. To combine the benefits of
these three categories of research, this study proposes an integrated framework, combining RA-, LCA- and criterion-based methods. The
integrated framework incorporates LCA techniques for the identification of the causal linkage for aspect, pathway, receptor and
impact, uses fuzzy logic to assess aspects, considers fuzzy conditions,
in likelihood assessment, and employs a new multi-criteria decision analysis method - multi-criteria and multi-connection comprehensive
assessment (MMCA) - to estimate significant aspects in EMS. The proposed model is verified, using a real case study and the results show
that this method successfully prioritizes the environmental aspects.
Abstract: Weather systems use enormously complex
combinations of numerical tools for study and forecasting.
Unfortunately, due to phenomena in the world climate, such
as the greenhouse effect, classical models may become
insufficient mostly because they lack adaptation. Therefore,
the weather forecast problem is matched for heuristic
approaches, such as Evolutionary Algorithms.
Experimentation with heuristic methods like Particle Swarm
Optimization (PSO) algorithm can lead to the development of
new insights or promising models that can be fine tuned with
more focused techniques. This paper describes a PSO
approach for analysis and prediction of data and provides
experimental results of the aforementioned method on realworld
meteorological time series.
Abstract: The increasing competitiveness in manufacturing
industry is forcing manufacturers to seek effective processing
schedules. The paper presents an optimization manufacture
scheduling approach for dependent details processing with given
processing sequences and times on multiple machines. By defining
decision variables as start and end moments of details processing it is
possible to use straightforward variables restrictions to satisfy
different technological requirements and to formulate easy to
understand and solve optimization tasks for multiple numbers of
details and machines. A case study example is solved for seven base
moldings for CNC metalworking machines processed on five
different machines with given processing order among details and
machines and known processing time-s duration. As a result of linear
optimization task solution the optimal manufacturing schedule
minimizing the overall processing time is obtained. The
manufacturing schedule defines the moments of moldings delivery
thus minimizing storage costs and provides mounting due-time
satisfaction. The proposed optimization approach is based on real
manufacturing plant problem. Different processing schedules variants
for different technological restrictions were defined and implemented
in the practice of Bulgarian company RAIS Ltd. The proposed
approach could be generalized for other job shop scheduling
problems for different applications.
Abstract: In this paper, an artificial intelligent technique for
robust digital image watermarking in multiwavelet domain is
proposed. The embedding technique is based on the quantization
index modulation technique and the watermark extraction process
does not require the original image. We have developed an
optimization technique using the genetic algorithms to search for
optimal quantization steps to improve the quality of watermarked
image and robustness of the watermark. In addition, we construct a
prediction model based on image moments and back propagation
neural network to correct an attacked image geometrically before the
watermark extraction process begins. The experimental results show
that the proposed watermarking algorithm yields watermarked image
with good imperceptibility and very robust watermark against various
image processing attacks.
Abstract: In this paper we present a general formalism for the
establishment of the family of selective regressor affine projection
algorithms (SR-APA). The SR-APA, the SR regularized APA (SR-RAPA),
the SR partial rank algorithm (SR-PRA), the SR binormalized
data reusing least mean squares (SR-BNDR-LMS), and the SR normalized
LMS with orthogonal correction factors (SR-NLMS-OCF)
algorithms are established by this general formalism. We demonstrate
the performance of the presented algorithms through simulations in
acoustic echo cancellation scenario.
Abstract: Automobile Industry has great importance in the
Spanish economy (8,7 % of the active Spanish population is
employed in this sector).The above mentioned sector has been one of
the principal sectors affected by the current economic crisis,
consistently, the budgets in advertising have been severely limited
(46,9 % less in the period of reference), these needs of reduction
have originated a substantial change in the advertising strategy (from
2007 the increase of the advertising investment in Internet is 251,6
%), and increase profitability. The growing use of social media by
consumers therefore makes online consumer conversations an
attractive additional format for Automobile firms to promote
products at a lower cost. This research analyzes the relation between
the activity in Social Media and the design in the car industry,
looking for relations between strategies of design based on Social
Media and sales and a channel of information for companies to know
what the consumer preferences. For this ongoing research we used a
longitudinal withdrawal of information has been used using
information of panel. Managerial and research implications of the
finding are discussed.
Abstract: Most electrical distribution systems are incurring large
losses as the loads are wide spread, inadequate reactive power
compensation facilities and their improper control. A typical static
VAR compensator consists of capacitor bank in binary sequential
steps operated in conjunction with a thyristor controlled reactor of the
smallest step size. This SVC facilitates stepless control of reactive
power closely matching with load requirements so as to maintain
power factor nearer to unity. This type of SVC-s requiring a
appropriately controlled TCR. This paper deals with an air cored
reactor suitable for distribution transformer of 3phase, 50Hz, Dy11,
11KV/433V, 125 KVA capacity. Air cored reactors are designed,
built, tested and operated in conjunction with capacitor bank in five
binary sequential steps. It is established how the delta connected TCR
minimizes the harmonic components and the operating range for
various electrical quantities as a function of firing angle is
investigated. In particular firing angle v/s line & phase currents, D.C.
components, THD-s, active and reactive powers, odd and even triplen
harmonics, dominant characteristic harmonics are all investigated and
range of firing angle is fixed for satisfactory operation. The harmonic
spectra for phase and line quantities at specified firing angles are
given. In case the TCR is operated within the bound specified in this
paper established through simulation studies are yielding the best
possible operating condition particularly free from all dominant
harmonics.
Abstract: This work presents a fusion of Log Gabor Wavelet
(LGW) and Maximum a Posteriori (MAP) estimator as a speech
enhancement tool for acoustical background noise reduction. The
probability density function (pdf) of the speech spectral amplitude is
approximated by a Generalized Laplacian Distribution (GLD).
Compared to earlier estimators the proposed method estimates the
underlying statistical model more accurately by appropriately
choosing the model parameters of GLD. Experimental results show
that the proposed estimator yields a higher improvement in
Segmental Signal-to-Noise Ratio (S-SNR) and lower Log-Spectral
Distortion (LSD) in two different noisy environments compared to
other estimators.
Abstract: This paper reviews designs of the built environment
from a sustainability perspective, emphasizing their importance in
achieving ecological and sustainable economic objectives. The built
environment has traditionally resulted in loss of biodiversity,
extinction of some species, climate change, excessive water use, land
degradation, space depletion, waste accumulation, energy
consumption and environmental pollution. Materials used like
plastics, metals, bricks, concrete, cement, natural aggregates, glass
and plaster have wreaked havoc on the earth´s resources, since they
have high levels of embodied energy hence not sustainable.
Additional resources are consumed during use and disposal phases.
Proposed designs for sustainability solutions include: ecological
sanitation and eco-efficiency systems that ensure social, economic,
environmental and technical sustainability. Renewable materials and
energy systems, passive cooling and heating systems and material
and energy reduction, reuse and recycling can improve the sector.
These ideas are intended to inform the field of ecological design of
the built environment.