Abstract: The main aim of this work is to develop a model of hydrogen sulfide (H2S) separation from natural gas by using membrane separation technology. The model is developed by incorporating three diffusion mechanisms which are Knudsen, viscous and surface diffusion towards membrane selectivity and permeability. The findings from the simulation result shows that the permeability of the gas is dependent toward the pore size of the membrane, operating pressure, operating temperature as well as feed composition. The permeability of methane has the highest value for Poly (1-trimethylsilyl-1-propyne ) PTMSP membrane at pore size of 0.1nm and decreasing toward a minimum peak at pore range 1 to 1.5 nm as pore size increased before it increase again for pore size is greater than 1.5 nm. On the other hand, the permeability of hydrogen sulfide is found to increase almost proportionally with the increase of membrane pore size. Generally, the increase of pressure will increase the permeability of gas since more driving force is provided to the system while increasing of temperature would decrease the permeability due to the surface diffusion drop off effect. A corroboration of the simulation result also showed a good agreement with the experimental data.
Abstract: This paper presents the experimental results of
leakage current waveforms which appears on porcelain insulator
surface due to existence of artificial pollutants. The tests have been
done using the chemical compounds of NaCl, Na2SiO3, H2SO4, CaO,
Na2SO4, KCl, Al2SO4, MgSO4, FeCl3, and TiO2. The insulator
surface was coated with those compounds and dried. Then, it was
tested in the chamber where the high voltage was applied. Using
correspondence analysis, the result indicated that the fundamental
harmonic of leakage current was very close to the applied voltage
and third harmonic leakage current was close to the yielded leakage
current amplitude. The first harmonic power was correlated to first
harmonic amplitude of leakage current, and third harmonic power
was close to third harmonic one. The chemical compounds of H2SO4
and Na2SiO3 affected to the power factor of around 70%. Both are the
most conductive, due to the power factor drastically increase among
the chemical compounds.
Abstract: Biological, psychological and social experiences and
perceptions of healthcare services in patients medically diagnosed of
coronary heart disease were investigated using a sample of 10
participants whose responses to the in-depth interview questions
were analyzed based on inter-and-intra-case analyses. The results
obtained revealed that advancing age, single status, divorce and/or
death of spouse and the issue of single parenting negatively impacted
patients- biopsychosocial experiences. The patients- experiences of
physical signs and symptoms, anxiety and depression, past serious
medical conditions, use of self-prescribed medications, family
history of poor mental/medical or physical health, nutritional
problems and insufficient physical activities heightened their risk of
coronary attack. Collectivist culture served as a big source of relieve
to the patients. Patients- temperament, experience of different
chronic life stresses/challenges, mood alteration, regular drinking,
smoking/gambling, and family/social impairments compounded their
health situation. Patients were satisfied with the biomedical services
rendered by the healthcare personnel, whereas their psychological
and social needs were not attended to. Effective procedural treatment
model, a holistic and multidimensional approach to the treatment of
heart disease patients was proposed.
Abstract: This paper presents a model for the evaluation of
energy performance and aerodynamic forces acting on a small
straight-bladed Darrieus-type vertical axis wind turbine depending on
blade geometrical section. It consists of an analytical code coupled to
a solid modeling software, capable of generating the desired blade
geometry based on the desired blade design geometric parameters.
Such module is then linked to a finite volume commercial CFD code
for the calculation of rotor performance by integration of the
aerodynamic forces along the perimeter of each blade for a full period
of revolution.After describing and validating the computational
model with experimental data, the results of numerical simulations
are proposed on the bases of two candidate airfoil sections, that is a
classical symmetrical NACA 0021 blade profile and the recently
developed DU 06-W-200 non-symmetric and laminar blade
profile.Through a full CFD campaign of analysis, the effects of blade
geometrical section on angle of attack are first investigated and then
the overall rotor torque and power are analyzed as a function of blade
azimuthal position, achieving a numerical quantification of the
influence of airfoil geometry on overall rotor performance.
Abstract: Design and evaluation of reciprocating compressors
should include a pulsation study. The object is to ensure that
predicted pulsation levels meet guidelines to limit vibration, shaking
forces, noise, associated pressure drops, horsepower losses and
fabrication cost and time to acceptable levels. This paper explains
procedures and recommendations to select and size pulsation
suppression devices to obtain optimum arrangement in terms of
pulsation, vibration, shaking forces, performance, reliability, safety,
operation, maintenance and commercial conditions. Model and
advanced formulations for pulsation study are presented. The effect
of the full fluid dynamic model on the prediction of pulsation waves
and resulting frequency spectrum distributions are discussed.
Advanced and optimum methods of controlling pulsations are
highlighted. Useful recommendations and guidelines for pulsation
control, piping pulsation analysis, pulsation vessel design, shaking
forces, low pressure drop orifices, pulsation study report and devices
to mitigate pulsation and shaking problems are discussed.
Abstract: A novel low-cost impedance control structure is
proposed for monitoring the contact force between end-effector and
environment without installing an expensive force/torque sensor.
Theoretically, the end-effector contact force can be estimated from the
superposition of each joint control torque. There have a nonlinear
matrix mapping function between each joint motor control input and
end-effector actuating force/torques vector. This new force control
structure can be implemented based on this estimated mapping matrix.
First, the robot end-effector is manipulated to specified positions, then
the force controller is actuated based on the hall sensor current
feedback of each joint motor. The model-free fuzzy sliding mode
control (FSMC) strategy is employed to design the position and force
controllers, respectively. All the hardware circuits and software
control programs are designed on an Altera Nios II embedded
development kit to constitute an embedded system structure for a
retrofitted Mitsubishi 5 DOF robot. Experimental results show that PI
and FSMC force control algorithms can achieve reasonable contact
force monitoring objective based on this hardware control structure.
Abstract: Cardiovascular diseases, principally atherosclerosis, are responsible for 30% of world deaths. Atherosclerosis is due to the formation of plaque. The fatty plaque may be at risk of rupture, leading typically to stroke and heart attack. The plaque is usually associated with a high degree of lumen reduction, called a stenosis.It is increasingly recognized that the initiation and progression of disease and the occurrence of clinical events is a complex interplay between the local biomechanical environment and the local vascular biology. The aim of this study is to investigate the flow behavior through a stenosed artery. A physical experiment was performed using an artery model and blood analogue fluid. An axisymmetric model constructed consists of contraction and expansion region that follow a mathematical form of cosine function. A 30% diameter reduction was used in this study. The flow field was measured using particle image velocimetry (PIV). Spherical particles with 20μm diameter were seeded in a water-glycerol-NaCl mixture. Steady flow Reynolds numbers are 250. The area of interest is the region after the stenosis where the flow separation occurs. The velocity field was measured and the velocity gradient was investigated. There was high particle concentration in the recirculation zone. High velocity gradient formed immediately after the stenosis throat created a lift force that enhanced particle migration to the flow separation area.
Abstract: The commercial finite element program LS-DYNA was employed to evaluate the response and energy absorbing capacity of cylindrical metal tubes that are externally wrapped with composite. The effects of composite wall thickness, loading conditions and fiber ply orientation were examined. The results demonstrate that a wrapped composite can be utilized effectively to enhance the crushing characteristics and energy absorbing capacity of the tubes. Increasing the thickness of the composite increases the mean force and the specific energy absorption under both static and dynamic crushing. The ply pattern affects the energy absorption capacity and the failure mode of the metal tube and the composite material property is also significant in determining energy absorption efficiency.
Abstract: Though nonlinear dynamic analysis using a specialized
hydro-code such as AUTODYN is accurate and useful tool for
progressive collapse assessment of a multi-story building subjected to
blast load, it takes too much time to be applied to a practical simulation
of progressive collapse of a tall building. In this paper, blast analysis of
a RC frame structure using a simplified model with Reinforcement
Contact technique provided in Ansys Workbench was introduced and
investigated on its accuracy. Even though the simplified model has a
fraction of elements of the detailed model, the simplified model with
this modeling technique shows similar structural behavior under the
blast load to the detailed model. The proposed modeling method can
be effectively applied to blast loading progressive collapse analysis of
a RC frame structure.
Abstract: The free and forced in-plane vibrations of axially
moving plates are investigated in this work. The plate possesses an
internal damping of which the constitutive relation obeys the
Kelvin-Voigt model, and the excitations are arbitrarily distributed on
two opposite edges. First, the equations of motion and the boundary
conditions of the axially moving plate are derived. Then, the extended
Ritz method is used to obtain discretized system equations. Finally,
numerical results for the natural frequencies and the mode shapes of
the in-plane vibration and the in-plane response of the moving plate
subjected to arbitrary edge excitations are presented. It is observed that
the symmetry class of the mode shapes of the in-plane vibration
disperses gradually as the moving speed gets higher, and the u- and
v-components of the mode shapes belong to different symmetry class.
In addition, large response amplitudes having shapes similar to the
mode shapes of the plate can be excited by the edge excitations at the
resonant frequencies and with the same symmetry class of distribution
as the u-components.
Abstract: In this paper a numerical simulation of electric and
hydrodynamic fields distribution in an electrofilter for dielectric
liquids cell is made. The simulation is made with the purpose to
determine the trajectory of particles that moves under the action of
external force in an electric and hydrodynamic field created inside of
an electrofilter for dielectric liquids. Particle trajectory is analyzed
for a dielectric liquid-solid particles suspension.
Abstract: The Connection Admission Control (CAC) problem is formulated in this paper as a discrete time optimal control problem. The control variables account for the acceptance/ rejection of new connections and forced dropping of in-progress connections. These variables are constrained to meet suitable conditions which account for the QoS requirements (Link Availability, Blocking Probability, Dropping Probability). The performance index evaluates the total throughput. At each discrete time, the problem is solved as an integer-valued linear programming one. The proposed procedure was successfully tested against suitably simulated data.
Abstract: Many firms implemented various initiatives such as outsourced manufacturing which could make a supply chain (SC) more vulnerable to various types of disruptions. So managing risk has become a critical component of SC management. Different types of SC vulnerability management methodologies have been proposed for managing SC risk, most offer only point-based solutions that deal with a limited set of risks. This research aims to reinforce SC risk management by proposing an integrated approach. SC risks are identified and a risk index classification structure is created. Then we develop a SC risk assessment approach based on the analytic network process (ANP) and the VIKOR methods under the fuzzy environment where the vagueness and subjectivity are handled with linguistic terms parameterized by triangular fuzzy numbers. By using FANP, risks weights are calculated and then inserted to the FVIKOR to rank the SC members and find the most risky partner.
Abstract: The incessant discomfort for Voluntary Counselling and Testing (VCT) exhibited by students in some tertiary institutions in Kano State, Nigeria is capable of causing Psychological Resistance as well as jeopardizing the purpose of HIV intervention. This study investigated the Prevalence of Psychological Resistance to VCT of HIV/AIDS among students of tertiary institutions in the state. Two null hypotheses were postulated and tested. Cross- Sectional Survey Design was employed in which 1512 sample was selected from a student population of 104,841 following Stratified Random Sampling technique. A self-developed 20-item scale whose reliability coefficient is 0.83 was used for data collection. Data analyzed via Chi-square and t-test reveals a prevalence of 38% with males (Mean=0.34; SD=0.475) constituting 60% and females (Mean=0.45; SD=0.498) 40%. Also, the calculated chi-square and ttest were not significant at 0.05 as such the null hypotheses were upheld. Recommendation offered suggests the use of reinforcement and social support for students who patronize HIV/AIDS counselling.
Abstract: This paper presents the identification of the impact
force acting on a simply supported beam. The force identification is
an inverse problem in which the measured response of the structure is
used to determine the applied force. The identification problem is
formulated as an optimization problem and the genetic algorithm is
utilized to solve the optimization problem. The objective function is
calculated on the difference between analytical and measured
responses and the decision variables are the location and magnitude
of the applied force. The results from simulation show the
effectiveness of the approach and its robustness vs. the measurement
noise and sensor location.
Abstract: In the competitive environment of aircraft industries it becomes absolutely necessary to improve the efficiency, performance of the aircrafts to reduce the development and operating costs considerably, in order to capitalize the market. An important contribution to improve the efficiency and performance can be
achieved by decreasing the aircraft weight through considerable
usage of composite materials in primary aircraft structures. In this study, a type of composite material called Carbon Fiber Reinforced
Plastic (CFRP) is explored for the usage is aircraft skin panels. Even
though there were plenty of studies and research has been already
carried out, here a practical example of an aircraft skin panel is taken
and substantiated the benefits of composites material usage over the
metallic skin panel. A crown skin panel of a commercial aircraft is
designed using both metal and composite materials. Stress analysis
has been carried out for both and margin of safety is estimated for the
critical load cases. The skin panels are compared for manufacturing,
tooling, assembly and cost parameters. Detail step by step comparison between metal and composite constructions are studied
and results are tabulated for better understanding.
Abstract: To date, theoretical studies concerning the Carbon
Fiber Reinforced Polymer (CFRP) strengthening of RC beams with
openings have been rather limited. In addition, various numerical
analyses presented so far have effectively simulated the behaviour of
solid beam strengthened by FRP material. In this paper, a two
dimensional nonlinear finite element analysis is presented to validate
against the laboratory test results of six RC beams. All beams had the
same rectangular cross-section geometry and were loaded under four
point bending. The crack pattern results of the finite element model
show good agreement with the crack pattern of the experimental
beams. The load midspan deflection curves of the finite element
models exhibited a stiffer result compared to the experimental beams.
The possible reason may be due to the perfect bond assumption used
between the concrete and steel reinforcement.
Abstract: Firstly, this study briefly presents the current situation that there exists a vast gap between current Chinese and Japanese seismic design specification for bridge pile foundation in liquefiable and liquefaction-induced lateral spreading ground; The Chinese and Japanese seismic design method and technical detail for bridge pile foundation in liquefying and lateral spreading ground are described and compared systematically and comprehensively, the methods of determining coefficient of subgrade reaction and its reduction factor as well as the computing mode of the applied force on pile foundation due to liquefaction-induced lateral spreading soil in Japanese design specification are especially introduced. Subsequently, the comparison indicates that the content of Chinese seismic design specification for bridge pile foundation in liquefiable and liquefaction-induced lateral spreading ground, just presenting some qualitative items, is too general and lacks systematicness and maneuverability. Finally, some defects of seismic design specification in China are summarized, so the improvement and revision of specification in the field turns out to be imperative for China, some key problems of current Chinese specifications are generalized and the corresponding improvement suggestions are proposed.
Abstract: Coated tool inserts can be considered as the backbone
of machining processes due to their wear and heat resistance.
However, defects of coating can degrade the integrity of these inserts
and the number of these defects should be minimized or eliminated if
possible. Recently, the advancement of coating processes and
analytical tools open a new era for optimizing the coating tools.
First, an overview is given regarding coating technology for cutting
tool inserts. Testing techniques for coating layers properties, as well
as the various coating defects and their assessment are also surveyed.
Second, it is introduced an experimental approach to examine the
possible coating defects and flaws of worn multicoated carbide
inserts using two important techniques namely scanning electron
microscopy and atomic force microscopy. Finally, it is
recommended a simple procedure for investigating manufacturing
defects and flaws of worn inserts.
Abstract: The present paper presents a finite element model and
analysis for the interaction between a piezoresistive tactile sensor and
biological tissues. The tactile sensor is proposed for use in minimally
invasive surgery to deliver tactile information of biological tissues to
surgeons. The proposed sensor measures the relative hardness of soft
contact objects as well as the contact force. Silicone rubbers were
used as the phantom of biological tissues. Finite element analysis of
the silicone rubbers and the mechanical structure of the sensor were
performed using COMSOL Multiphysics (v3.4) environment. The
simulation results verify the capability of the sensor to be used to
differentiate between different kinds of silicone rubber materials.