Abstract: In this paper, we proposed a novel SCR (Silicon Controlled
Rectifier) - based ESD (Electrostatic Discharge) protection device for I/O
and power clamp. The proposed device has a higher holding voltage
characteristic than conventional SCR. These characteristics enable to have
latch-up immunity under normal operating conditions as well as superior full
chip ESD protection. The proposed device was analyzed to figure out
electrical characteristics and tolerance robustness in term of individual
design parameters (D1, D2, D3). They are investigated by using the
Synopsys TCAD simulator. As a result of simulation, holding voltage
increased with different design parameters. The holding voltage of the
proposed device changes from 3.3V to 7.9V. Also, N-Stack structure ESD
device with the high holding voltage is proposed. In the simulation results,
2-stack has holding voltage of 6.8V and 3-stack has holding voltage of
10.5V. The simulation results show that holding voltage of stacking
structure can be larger than the operation voltage of high-voltage
application.
Abstract: Radial profiles of particle velocities were investigated
in a 6.1m high methanol-to-olefins cold model experimental device
using a TSI laser Doppler velocimeter. The effect of axial height on
flow development was not obvious in fully developed region under the
same operating condition. Superficial gas velocity and solid
circulating rate had significant influence on particle velocity in the
center region of the riser. Besides, comparisons among rising,
descending and average particle velocity were conducted. The particle
average velocity was similar to the rising particle velocity and higher
than the descending particle velocity in radial locations except the wall
region of riser.
Abstract: When printing a plate (or dish) by an FDM 3D printer,
the process normally requires support material, which causes several
problems. This paper proposes a method for forming thin plates
without using wasteful support material. This method requires several
extraordinary parameter values when slicing plates. The experiments
show that the plates can, for the most part, be successfully formed
using a conventional slicer and a 3D printer; however, seams between
layers spoil them and the quality of printed objects strongly depends
on the slicer.
Abstract: In this paper, we investigated the athermal pressure
behavior of the structural and elastic properties of scheelite BaWO4
phase up to 7 GPa using the ab initio pseudo-potential method. The
calculated lattice parameters pressure relation have been compared
with the experimental values and found to be in good agreement with
these results. Moreover, we present for the first time the investigation
of the elastic properties of this compound using the density functional
perturbation theory (DFPT). It is shown that this phase is
mechanically stable up to 7 GPa after analyzing the calculated elastic
constants. Other relevant quantities such as bulk modulus, pressure
derivative of bulk modulus, shear modulus; Young’s modulus,
Poisson’s ratio, anisotropy factors, Debye temperature and sound
velocity have been calculated. The obtained results, which are
reported for the first time to the best of the author’s knowledge, can
facilitate assessment of possible applications of the title material.
Abstract: In this study free vibration analysis of aluminum
honeycomb sandwich structures were carried out experimentally and
numerically. The natural frequencies and mode shapes of sandwich
structures fabricated with different configurations for clamped-free
boundary condition were determined. The effects of lower and upper
face sheet thickness, the core material thickness, cell diameter, cell
angle and foil thickness on the vibration characteristics were
examined. The numerical studies were performed with ANSYS
package. While the sandwich structures were modeled in ANSYS the
continuum model was used. Later, the numerical results were
compared with the experimental findings.
Abstract: In addition to environmental parameters like rain,
temperature diseases on crop is a major factor which affects
production quality & quantity of crop yield. Hence disease
management is a key issue in agriculture. For the management of
disease, it needs to be detected at early stage. So, treat it properly &
control spread of the disease. Now a day, it is possible to use the
images of diseased leaf to detect the type of disease by using image
processing techniques. This can be achieved by extracting features
from the images which can be further used with classification
algorithms or content based image retrieval systems. In this paper,
color image is used to extract the features such as mean and standard
deviation after the process of region cropping. The selected features
are taken from the cropped image with different image size samples.
Then, the extracted features are taken in to the account for
classification using Fuzzy Inference System (FIS).
Abstract: This study aimed to determine the possible protective effects of L‐carnitine against gentamicin‐induced nephrotoxicity. Forty male albino rats were divided into 4 groups (10 rats each); Group 1: normal control, group 2: induced nephrotoxicity (gentamicin 50 mg/kg/day S.C; 8 days), group 3: treated with L‐ carnitine (40 mg/kg/d SC for 12 days) and group 4: treated with L‐ carnitine 4 days before and for 8 days in concomitant with gentamicin. Gentamicin‐induced nephrotoxicity (group 2): caused significant increase in serum urea, creatinine, urinary N‐acetyl‐B‐D‐ glucosaminidase (NAG), gamma glutamyl transpeptidase (GGT), urinary total protein and kidney tissue malondialdehyde (MDA) with significant decrease in serum superoxide dismutase (SOD), serum catalase and creatinine clearance and marked tubular necrosis in the proximal convoluted tubules with interruption in the basement membrane around the necrotic tubule compared to the normal control group. L‐carnitine 4 days before and for 8 days in concomitant with gentamicin (group 4) offered marked decrease in serum urea, serum creatinine, urinary NAG, urinary GGT, urinary proteins and kidney tissue MDA, with marked increase in serum SOD, serum catalase and creatinine clearance with marked improvement in the tubular damage compared to gentamicin‐induced nephrotoxicity group. L‐carnitine administered for 12 days produced no change in the parameters mentioned above as compared to the normal control group. In conclusion: L‐carnitine could reduce most of the biochemical parameters and also improve the histopathological features of kidney asscociated with gentamicin induced‐nephrotoxicity.
Abstract: Hemoglobin (HB) indicates anemia level and by
extension may reflect the nutritional level and perhaps the immunity
of an individual. Some antiretroviral drugs like Zidovudine are
known to cause anemia in people living with HIV/AIDS (PLWHA).
A cross sectional study using demographic data and blood specimen
from 218 female commercial sex workers attending antiretroviral
therapy (ART) clinics was conducted between December, 2009 and
July, 2011 to assess the effect of zidovudine on hematologic, and
RNA viral load of female sex workers receiving antiretroviral
treatment in north western Nigeria. Anemia is a common and serious
complication of both HIV infection and its treatment. In the setting of
HIV infection, anemia has been associated with decreased quality of
life, functional status, and survival. Antiretroviral therapy,
particularly the highly active antiretroviral therapy (HAART), has
been associated with a decrease in the incidence and severity of
anemia in HIV-infected patients who have received a HAART
regimen for at least 1 year. In this study, result has shown that of the
218 patients, 26 with hemoglobin count between 5.1 – 10g/dl were
observed to have the highest viral load count of 300,000 –
350,000copies/ml. It was also observed that most patients (190) with
HB of 10.1 – 15.0g/dl had viral load count of 200,000 – 250,000
copies /ml. An inverse relationship therefore exists i.e. the lower the
hemoglobin level, the higher the viral load count even though the test
statistics did not show any significance between the two (P = 0.206).
This shows that multivariate logistic regression analysis
demonstrated that anemia was associated with a CD4 + cell count
below 50/μL, female sex workers with a viral load above 100,000
copies/mL, who use zidovudine.
Severe anemia was less prevalent in this study population than in
historical comparators; however, mild to moderate anemia rates
remain high. The study therefore recommends that hematological and
virologic parameters be monitored closely in patients receiving first
line ART regimen.
Abstract: The numerical simulation has made tremendous
advances in investigating the blood flow phenomenon through elastic
arteries. Such study can be useful in demonstrating the disease
progression and hemodynamics of cardiovascular diseases such as
atherosclerosis. In the present study, patient specific case diagnosed
with partially stenosed complete right ICA and normal left carotid
bifurcation without any atherosclerotic plaque formation is
considered. 3D patient specific carotid bifurcation model is generated
based on CT scan data using MIMICS-4.0 and numerical analysis is
performed using FSI solver in ANSYS-14.5. The blood flow is
assumed to be incompressible, homogenous and Newtonian, while
the artery wall is assumed to be linearly elastic. The two-way
sequentially coupled transient FSI analysis is performed using FSI
solver for three pulse cycles. The hemodynamic parameters such as
flow pattern, Wall Shear Stress, pressure contours and arterial wall
deformation are studied at the bifurcation and critical zones such as
stenosis. The variation in flow behavior is studied throughout the
pulse cycle. Also, the simulation results reveal that there is a
considerable increase in the flow behavior in stenosed carotid in
contrast to the normal carotid bifurcation system. The investigation
also demonstrates the disturbed flow pattern especially at the
bifurcation and stenosed zone elevating the hemodynamics,
particularly during peak systole and later part of the pulse cycle. The
results obtained agree well with the clinical observation and
demonstrates the potential of patient specific numerical studies in
prognosis of disease progression and plaque rupture.
Abstract: In the present study, response surface methodology has been used to optimize turn-assisted deep cold rolling process of AISI 4140 steel. A regression model is developed to predict surface hardness and surface roughness using response surface methodology and central composite design. In the development of predictive model, deep cold rolling force, ball diameter, initial roughness of the workpiece, and number of tool passes are considered as model variables. The rolling force and the ball diameter are the significant factors on the surface hardness and ball diameter and numbers of tool passes are found to be significant for surface roughness. The predicted surface hardness and surface roughness values and the subsequent verification experiments under the optimal operating conditions confirmed the validity of the predicted model. The absolute average error between the experimental and predicted values at the optimal combination of parameter settings for surface hardness and surface roughness is calculated as 0.16% and 1.58% respectively. Using the optimal processing parameters, the surface hardness is improved from 225 to 306 HV, which resulted in an increase in the near surface hardness by about 36% and the surface roughness is improved from 4.84µm to 0.252 µm, which resulted in decrease in the surface roughness by about 95%. The depth of compression is found to be more than 300µm from the microstructure analysis and this is in correlation with the results obtained from the microhardness measurements. Taylor hobson talysurf tester, micro vickers hardness tester, optical microscopy and X-ray diffractometer are used to characterize the modified surface layer.
Abstract: Given the limited research on Small and Mediumsized
Enterprises’ (SMEs) contribution to Corporate Social
Responsibility (CSR) and even scarcer research on Swiss SMEs, this
paper helps to fill these gaps by enabling the identification of supranational
SME parameters. Thus, the paper investigates the current
state of SME practices in Switzerland and across 15 other countries.
Combining the degree to which SMEs demonstrate an explicit (or
business case) approach or see CSR as an implicit moral activity with
the assessment of their attributes for “variety of capitalism” defines
the framework of this comparative analysis. To outline Swiss small
business CSR patterns in particular, 40 SME owner-managers were
interviewed. A secondary data analysis of studies from different
countries laid groundwork for this comparative overview of small
business CSR. The paper identifies Swiss small business CSR as
driven by norms, values, and by the aspiration to contribute to
society, thus, as an implicit part of the day-to-day business. Similar to
most Central European, Mediterranean, Nordic, and Asian countries,
explicit CSR is still very rare in Swiss SMEs. Astonishingly, also
British and American SMEs follow this pattern in spite of their strong
and distinctly liberal market economies. Though other findings show
that nationality matters this research concludes that SME culture and
an informal CSR agenda are strongly formative and superseding even
forces of market economies, nationally cultural patterns, and
language. Hence, classifications of countries by their market system,
as found in the comparative capitalism literature, do not match the
CSR practices in SMEs as they do not mirror the peculiarities of their
business. This raises questions on the universality and
generalisability of unmediated, explicit management concepts,
especially in the context of small firms.
Abstract: In this study, three robust predicting methods, namely artificial neural network (ANN), adaptive neuro fuzzy inference system (ANFIS) and support vector machine (SVM) were used for computing the resonant frequency of A-shaped compact microstrip antennas (ACMAs) operating at UHF band. Firstly, the resonant frequencies of 144 ACMAs with various dimensions and electrical parameters were simulated with the help of IE3D™ based on method of moment (MoM). The ANN, ANFIS and SVM models for computing the resonant frequency were then built by considering the simulation data. 124 simulated ACMAs were utilized for training and the remaining 20 ACMAs were used for testing the ANN, ANFIS and SVM models. The performance of the ANN, ANFIS and SVM models are compared in the training and test process. The average percentage errors (APE) regarding the computed resonant frequencies for training of the ANN, ANFIS and SVM were obtained as 0.457%, 0.399% and 0.600%, respectively. The constructed models were then tested and APE values as 0.601% for ANN, 0.744% for ANFIS and 0.623% for SVM were achieved. The results obtained here show that ANN, ANFIS and SVM methods can be successfully applied to compute the resonant frequency of ACMAs, since they are useful and versatile methods that yield accurate results.
Abstract: Obesity and osteoporosis are the two diseases whose
increasing prevalence and high impact on the global morbidity and
mortality, during the two recent decades, have gained a status of
major health threats worldwide. Obesity purports to affect the bone
metabolism through complex mechanisms. Debated data on the
connection between the bone mineral density and fracture prevalence
in the obese patients are widely presented in literature. There is
evidence that the correlation of weight and fracture risk is sitespecific.
This study is aimed at determining the connection between
the bone mineral density (BMD) and trabecular bone score (TBS)
parameters in Ukrainian women suffering from obesity. We
examined 1025 40-89-year-old women, divided them into the groups
according to their body mass index: Group A included 360 women
with obesity whose BMI was ≥30 kg/m2, and Group B – 665 women
with no obesity and BMI of
Abstract: Intermittent behavior near the boundary of phase
synchronization in the presence of noise is studied. In certain range of
the coupling parameter and noise intensity the intermittency of eyelet
and ring intermittencies is shown to take place. Main results are
illustrated using the example of two unidirectional coupled Rössler
systems. Similar behavior is shown to take place in two
hydrodynamical models of Pierce diode coupled unidirectional.
Abstract: Boiling process is characterized by the rapid
formation of vapour bubbles at the solid–liquid interface (nucleate
boiling) with pre-existing vapour or gas pockets. Computational fluid
dynamics (CFD) is an important tool to study bubble dynamics. In
the present study, CFD simulation has been carried out to determine
the bubble detachment diameter and its terminal velocity. Volume of
fluid method is used to model the bubble and the surrounding by
solving single set of momentum equations and tracking the volume
fraction of each of the fluids throughout the domain. In the
simulation, bubble is generated by allowing water-vapour to enter a
cylinder filled with liquid water through an inlet at the bottom. After
the bubble is fully formed, the bubble detaches from the surface and
rises up during which the bubble accelerates due to the net balance
between buoyancy force and viscous drag. Finally when these forces
exactly balance each other, it attains a constant terminal velocity. The
bubble detachment diameter and the terminal velocity of the bubble
are captured by the monitor function provided in FLUENT. The
detachment diameter and the terminal velocity obtained are compared
with the established results based on the shape of the bubble. A good
agreement is obtained between the results obtained from simulation
and the equations in comparison with the established results.
Abstract: We investigate experimentally and theoretically the
dynamics of a capacitive resonator under mixed frequency excitation
of two AC harmonic signals. The resonator is composed of a proof
mass suspended by two cantilever beams. Experimental
measurements are conducted using a laser Doppler Vibrometer to
reveal the interesting dynamics of the system when subjected to twosource
excitation. A nonlinear single-degree-of-freedom model is
used for the theoretical investigation. The results reveal combination
resonances of additive and subtractive type, which are shown to be
promising to increase the bandwidth of the resonator near primary
resonance frequency. Our results also demonstrate the ability to shift
the combination resonances to much lower or much higher frequency
ranges. We also demonstrate the dynamic pull-in instability under
mixed frequency excitation.
Abstract: This paper presents a computational study of steady
state three dimensional very high turbulent flow and heat transfer
characteristics in a constant temperature-surfaced circular duct fitted
with 900 hemispherical inline baffles. The computations are based on
realizable k-ɛ model with standard wall function considering the
finite volume method, and the SIMPLE algorithm has been
implemented. Computational Study are carried out for Reynolds
number, Re ranging from 80000 to 120000, Prandtl Number, Pr of
0.73, Pitch Ratios, PR of 1,2,3,4,5 based on the hydraulic diameter of
the channel, hydrodynamic entry length, thermal entry length and the
test section. Ansys Fluent 15.0 software has been used to solve the
flow field. Study reveals that circular pipe having baffles has a higher
Nusselt number and friction factor compared to the smooth circular
pipe without baffles. Maximum Nusselt number and friction factor
are obtained for the PR=5 and PR=1 respectively. Nusselt number
increases while pitch ratio increases in the range of study; however,
friction factor also decreases up to PR 3 and after which it becomes
almost constant up to PR 5. Thermal enhancement factor increases
with increasing pitch ratio but with slightly decreasing Reynolds
number in the range of study and becomes almost constant at higher
Reynolds number. The computational results reveal that optimum
thermal enhancement factor of 900 inline hemispherical baffle is
about 1.23 for pitch ratio 5 at Reynolds number 120000.It also shows
that the optimum pitch ratio for which the baffles can be installed in
such very high turbulent flows should be 5. Results show that pitch
ratio and Reynolds number play an important role on both fluid flow
and heat transfer characteristics.
Abstract: The aim of this investigation is to elaborate nearinfrared
methods for testing and recognition of chemical components
and quality in “Pannon wheat” allied (i.e. true to variety or variety
identified) milling fractions as well as to develop spectroscopic
methods following the milling processes and evaluate the stability of
the milling technology by different types of milling products and
according to sampling times, respectively. These wheat categories
produced under industrial conditions where samples were collected
versus sampling time and maximum or minimum yields. The changes
of the main chemical components (such as starch, protein, lipid) and
physical properties of fractions (particle size) were analysed by
dispersive spectrophotometers using visible (VIS) and near-infrared
(NIR) regions of the electromagnetic radiation. Close correlation
were obtained between the data of spectroscopic measurement
techniques processed by various chemometric methods (e.g. principal
component analysis [PCA], cluster analysis [CA]) and operation
condition of milling technology. It is obvious that NIR methods are
able to detect the deviation of the yield parameters and differences of
the sampling times by a wide variety of fractions, respectively. NIR
technology can be used in the sensitive monitoring of milling
technology.
Abstract: Submerged arc welding is a very complex process. It
is a very efficient and high performance welding process. In this
present study an attempt have been done to reduce the welding
distortion by increased amount of oxide flux through TiO2 in
submerged arc welding process. Care has been taken to avoid the
excessiveness of the adding agent for attainment of significant
results. Data Envelopment Analysis (DEA) based BAT algorithm is
used for the parametric optimization purpose in which DEA is used
to convert multi response parameters into a single response
parameter. The present study also helps to know the effectiveness of
the addition of TiO2 in active flux during submerged arc welding
process.
Abstract: Using the quantum hydrodynamic (QHD) model the
nonlinear properties of ion-acoustic waves in are lativistically
degenerate quantum plasma is investigated by deriving a nonlinear
Spherical Kadomtsev–Petviashvili (SKP) equation using the
standard reductive perturbation method equation. It was found that
the electron degeneracy parameter significantly affects the linear
and nonlinear properties of ion-acoustic waves in quantum plasma.