Abstract: The microstrip antennas area has seen some inventive
work in recent years and is now one of the most dynamic fields of
antenna theory. A novel and simple wideband monopole antenna is
presented printed on a single dielectric substrate which is fed by a 50
ohm microstrip line having a low-profile antenna structure with two
parallel s-shaped meandered line of same size. This antenna is fed by
a coaxial feeding tube. In this research, S–form microstrip patch antenna is designed from
measuring the prototypes of the proposed antenna one available
bands with 10db return loss bandwidths of about GPS application
(GPS L2 1490 MHz) and covering the 1400 to 1580 MHz frequency
band at 1.5 GHz, the simulated results for main parameters such as
return loss, impedance bandwidth, radiation patterns, and gains are
also discussed herein. The modeling study shows that such antennas,
in simplicity design and supply, can satisfy GPS application. Two
parallel slots are incorporated to disturb the surface flow path,
introducing local inductive effect. This antenna is fed by a coaxial
feeding tube.
Abstract: In this study, a multi objective optimization for end
milling of Al 6061 alloy has been presented to provide better
surface quality and higher Material Removal Rate (MRR). The input
parameters considered for the analysis are spindle speed, depth of cut
and feed. The experiments were planned as per Taguchis design of
experiment, with L27 orthogonal array. The Grey Relational Analysis
(GRA) has been used for transforming multiple quality responses
into a single response and the weights of the each performance
characteristics are determined by employing the Principal Component
Analysis (PCA), so that their relative importance can be properly and
objectively described. The results reveal that Taguchi based G-PCA
can effectively acquire the optimal combination of cutting parameters.
Abstract: Liquid-Liquid Equilibrium (LLE) data are measured
for the ternary mixtures of water + 1-butanol + butyl acetate and
quaternary mixtures of water + 1-butanol + butyl acetate + glycerol at
atmospheric pressure at 313.15 K. In addition, isothermal
vapor–liquid–liquid equilibrium (VLLE) data are determined
experimentally at 333.15 K. The region of heterogeneity is found to
increase as the hydrophilic agent (glycerol) is introduced into the
aqueous mixtures. The experimental data are correlated with the
NRTL model. The predicted results from the solution model with the
model parameters determined from the constituent binaries are also
compared with the experimental values.
Abstract: A flow column has been innovatively used in the
design of a new electrocoagulation reactor (ECR1) that will reduce
the temperature of water being treated; where the flow columns work
as a radiator for the water being treated. In order to investigate the
performance of ECR1 and compare it to that of traditional reactors;
600 mL water samples with an initial temperature of 350C were
pumped continuously through these reactors for 30 min at current
density of 1 mA/cm2. The temperature of water being treated was
measured at 5 minutes intervals over a 30 minutes period using a
thermometer. Additional experiments were commenced to investigate
the effects of initial temperature (15-350C), water conductivity (0.15
– 1.2 S) and current density (0.5 -3 mA/cm2) on the performance of
ECR1.
The results obtained demonstrated that the ECR1, at a current
density of 1 mA/cm2 and continuous flow model, reduced water
temperature from 350C to the vicinity of 280C during the first 15
minutes and kept the same level till the end of the treatment time.
While, the temperature increased from 28.1 to 29.80C and from 29.8
to 31.90C in the batch and the traditional continuous flow models
respectively. In term of initial temperature, ECR1 maintained the
temperature of water being treated within the range of 22 to 280C
without the need for external cooling system even when the initial
temperatures varied over a wide range (15 to 350C). The influent
water conductivity was found to be a significant variable that affect
the temperature. The desirable value of water conductivity is 0.6 S.
However, it was found that the water temperature increased rapidly
with a higher current density.
Abstract: As the Silicon oxide scaled down in MOSFET
technology to few nanometers, gate Direct Tunneling (DT) in
Floating gate (FGMOSFET) devices has become a major concern for
analog designers. FGMOSFET has been used in many low-voltage
and low-power applications, however, there is no accurate model that
account for DT gate leakage in nano-scale. This paper studied and
analyzed different simulation models for FGMOSFET using TSMC
90-nm technology. The simulation results for FGMOSFET cascade
current mirror shows the impact of DT on circuit performance in
terms of current and voltage without the need for fabrication. This
works shows the significance of using an accurate model for
FGMOSFET in nan-scale technologies.
Abstract: In the present study, the properties of Al-Al2O3
nanocomposite hollow sphere structures were investigated. For this
reason, the Al-based nanocomposite hollow spheres with different
amounts of nano-alumina reinforcement (0-10wt %) and different
ratio of thickness to diameter (t/D: 0.06-0.3) were prepared via a
powder metallurgy method. Then, the effect of mentioned parameters
was studied on physical and quasi static mechanical properties of
their related prepared structures (open/closed cell) such as density,
hardness, strength, and energy absorption. It was found that, as the
t/D ratio increases the relative density, compressive strength and
energy absorption increase. The highest values of strength and energy
absorption were obtained from the specimen with 5 wt. % of
nanoparticle reinforcement, t/D of 0.3 (t=1 mm, D=400μm) as 22.88
MPa and 13.24 MJ/m3, respectively. The moderate specific strength
of prepared composites in the present study showed the good
consistency with the properties of others low carbon steel composite
with similar structure.
Abstract: In this paper, analysis of an infinite beam resting on
multilayer tensionless extensible geosynthetic reinforced granular
fill-poor soil system overlying soft soil strata under moving load with
constant velocity is presented. The beam is subjected to a
concentrated load moving with constant velocity. The upper
reinforced granular bed is modeled by a rough membrane embedded
in Pasternak shear layer overlying a series of compressible nonlinear
winkler springs representing the underlying the very poor soil. The
multilayer tensionless extensible geosynthetic layer has been
assumed to deform such that at interface the geosynthetic and the soil
have some deformation. Nonlinear behaviour of granular fill and the
very poor soil has been considered in the analysis by means of
hyperbolic constitutive relationships. Governing differential
equations of the soil foundation system have been obtained and
solved with the help of appropriate boundary conditions. The solution
has been obtained by employing finite difference method by means of
Gauss-Siedal iterative scheme. Detailed parametric study has been
conducted to study the influence of various parameters on the
response of soil–foundation system under consideration by means of
deflection and bending moment in the beam and tension mobilized in
the geosynthetic layer. These parameters include magnitude of
applied load, velocity of load, damping, ultimate resistance of poor
soil and granular fill layer. Range of values of parameters has been
considered as per Indian Railway conditions. This study clearly
observed that the comparisons of multilayer tensionless extensible
geosynthetic reinforcement with poor foundation soil and magnitude
of applied load, relative compressibility of granular fill and ultimate
resistance of poor soil has significant influence on the response of
soil–foundation system.
Abstract: Propagation of arbitrary amplitude nonlinear Alfven
waves has been investigated in low but finite β electron-positron-ion
plasma including full ion dynamics. Using Sagdeev pseudopotential
method an energy integral equation has been derived. The Sagdeev
potential has been calculated for different plasma parameters and it
has been shown that inclusion of ion parallel motion along the
magnetic field changes the nature of slow shear Alfven wave solitons
from dip type to hump type. The effects of positron concentration,
plasma-β and obliqueness of the wave propagation on the solitary
wave structure have also been examined.
Abstract: Background: Muscle Energy Techniques (MET) have
been widely used by manual therapists over the past years, but still
limited research validated its use and there was limited evidence to
substantiate the theories used to explain its effects. Objective: To
investigate the effect of Muscle Energy Technique (MET) on anterior
pelvic tilt in patients with lumbar spondylosis. Design: Randomized
controlled trial. Subjects: Thirty patients with anterior pelvic tilt from
both sexes were involved, aged between 35 to 50 years old and they
were divided into MET and control groups with 15 patients in each.
Methods: All patients received 3sessions/week for 4 weeks where the
study group received MET, Ultrasound and Infrared, and the control
group received U.S and I.R only. Pelvic angle was measured by
palpation meter, pain severity by the visual analogue scale and
functional disabilities by the Oswestry disability index. Results: Both
groups showed significant improvement in all measured variables.
The MET group was significantly better than the control group in
pelvic angle, pain severity, and functional disability as p-value were
(0.001, 0.0001, 0.0001) respectively. Conclusion and implication: the
study group fulfilled greater improvement in all measured variables
than the control group which implies that application of MET in
combination with U.S and I.R were more effective in improving
pelvic tilting angle, pain severity and functional disabilities than
using electrotherapy only.
Abstract: Singular value decomposition based optimisation of
geometric design parameters of a 5-speed gearbox is studied. During
the optimisation, a four-degree-of freedom torsional vibration model
of the pinion gear-wheel gear system is obtained and the minimum
singular value of the transfer matrix is considered as the objective
functions. The computational cost of the associated singular value
problems is quite low for the objective function, because it is only
necessary to compute the largest and smallest singular values (μmax
and μmin) that can be achieved by using selective eigenvalue solvers;
the other singular values are not needed. The design parameters are
optimised under several constraints that include bending stress,
contact stress and constant distance between gear centres. Thus, by
optimising the geometric parameters of the gearbox such as, the
module, number of teeth and face width it is possible to obtain a
light-weight-gearbox structure. It is concluded that the all optimised
geometric design parameters also satisfy all constraints.
Abstract: Particle size distribution, the most important
characteristics of aerosols, is obtained through electrical
characterization techniques. The dynamics of charged nanoparticles
under the influence of electric field in Electrical Mobility
Spectrometer (EMS) reveals the size distribution of these particles.
The accuracy of this measurement is influenced by flow conditions,
geometry, electric field and particle charging process, therefore by
the transfer function (transfer matrix) of the instrument. In this work,
a wire-cylinder corona charger was designed and the combined fielddiffusion
charging process of injected poly-disperse aerosol particles
was numerically simulated as a prerequisite for the study of a
multichannel EMS. The result, a cloud of particles with no uniform
charge distribution, was introduced to the EMS. The flow pattern and
electric field in the EMS were simulated using Computational Fluid
Dynamics (CFD) to obtain particle trajectories in the device and
therefore to calculate the reported signal by each electrometer.
According to the output signals (resulted from bombardment of
particles and transferring their charges as currents), we proposed a
modification to the size of detecting rings (which are connected to
electrometers) in order to evaluate particle size distributions more
accurately. Based on the capability of the system to transfer
information contents about size distribution of the injected particles,
we proposed a benchmark for the assessment of optimality of the
design. This method applies the concept of Von Neumann entropy
and borrows the definition of entropy from information theory
(Shannon entropy) to measure optimality. Entropy, according to the
Shannon entropy, is the ''average amount of information contained in
an event, sample or character extracted from a data stream''.
Evaluating the responses (signals) which were obtained via various
configurations of detecting rings, the best configuration which gave
the best predictions about the size distributions of injected particles,
was the modified configuration. It was also the one that had the
maximum amount of entropy. A reasonable consistency was also
observed between the accuracy of the predictions and the entropy
content of each configuration. In this method, entropy is extracted
from the transfer matrix of the instrument for each configuration.
Ultimately, various clouds of particles were introduced to the
simulations and predicted size distributions were compared to the
exact size distributions.
Abstract: Spacer grid assembly supporting the nuclear fuel rods
is an important concern in the design of structural components of a
Pressurized Water Reactor (PWR). The spacer grid is composed by
springs and dimples which are formed from a strip sheet by means of
blanking and stamping processes. In this paper, the blanking process
and tooling parameters are evaluated by means of a 2D plane-strain
finite element model in order to evaluate the punch load and quality
of the sheared edges of Inconel 718 strips used for nuclear spacer
grids. A 3D finite element model is also proposed to predict the
tooling loads resulting from the stamping process of a preformed
Inconel 718 strip and to analyse the residual stress effects upon the
spring and dimple design geometries of a nuclear spacer grid.
Abstract: The objective of the study is to assess the
implementation of LED lighting into forest machine work in the dark.
In addition, the paper includes a wide variety of important and
relevant safety and health parameters. In modern, computerized work
in the cab of forest machines, artificial illumination is a demanding
task when performing duties, such as the visual inspections of wood
and computer calculations. We interviewed entrepreneurs and
gathered the following as the most pertinent themes: (1) safety, (2)
practical problems, and (3) work with LED lighting. The most
important comments were in regards to the practical problems of
LED lighting. We found indications of technical problems in
implementing LED lighting, like snow and dirt on the surfaces of
lamps that dim the emission of light. Moreover, service work in the
dark forest is dangerous and increases the risks of on-site accidents.
We also concluded that the amount of blue light to the eyes should be
assessed, especially, when the drivers are working in a semi-dark cab.
Abstract: Chalcopyrite (CuFeS2) is the most common primary
mineral used for the commercial production of copper. The low
dissolution efficiency of chalcopyrite in sulfate media has prevented
an efficient industrial leaching of this mineral in sulfate media. Ferric
ions, bacteria, oxygen and other oxidants have been used as oxidizing
agents in the leaching of chalcopyrite in sulfate and chloride media
under atmospheric or pressure leaching conditions. Two leaching
methods were studied to evaluate chalcopyrite (CuFeS2) dissolution
in acid media. First, the conventional oxidative acid leaching method
was carried out using sulfuric acid (H2SO4) and potassium
dichromate (K2Cr2O7) as oxidant at atmospheric pressure. Second,
microwave-assisted acid leaching was performed using the
microwave accelerated reaction system (MARS) for same reaction
media. Parameters affecting the copper extraction such as leaching
time, leaching temperature, concentration of H2SO4 and
concentration of K2Cr2O7 were investigated. The results of
conventional acid leaching experiments were compared to the
microwave leaching method. It was found that the copper extraction
obtained under high temperature and high concentrations of oxidant
with microwave leaching is higher than those obtained
conventionally. 81% copper extraction was obtained by the
conventional oxidative acid leaching method in 180 min, with the
concentration of 0.3 mol/L K2Cr2O7 in 0.5M H2SO4 at 50 ºC, while
93.5% copper extraction was obtained in 60 min with microwave
leaching method under same conditions.
Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: Application of biochar to arable soils represents a new
approach to restore soil health and quality. Many studies reported the
positive effect of biochar application on soil fertility and
development of soil microbial community. Moreover biochar may
affect the soil water retention, but this effect has not been sufficiently
described yet. Therefore this study deals with the influence of
biochar application on: microbial activities in soil, availability of
mineral nitrogen in soil for microorganisms, mineral nitrogen
retention and plant production. To demonstrate the effect of biochar
addition on the above parameters, the pot experiment was realized.
As a model crop, Lactuca sativa L. was used and cultivated from
December 10th 2014 till March 22th 2015 in climate chamber in
thoroughly homogenized arable soil with and without addition of
biochar. Five variants of experiment (V1 – V5) with different regime
of irrigation were prepared. Variants V1 – V2 were fertilized by
mineral nitrogen, V3 – V4 by biochar and V5 was a control. The
significant differences were found only in plant production and
mineral nitrogen retention. The highest content of mineral nitrogen
in soil was detected in V1 and V2, about 250 % in comparison with
the other variants. The positive effect of biochar application on soil
fertility, mineral nitrogen availability was not found. On the other
hand results of plant production indicate the possible positive effect
of biochar application on soil water retention.
Abstract: In order to study the effect of different levels of triple
super phosphate chemical fertilizer and biological phosphate fertilizer
(fertile 2) on some morphological traits of corn this research was
carried out in Ahvaz in 2002 as a factorial experiment in randomized
complete block design with 4 replications). The experiment included
two factors: first, biological phosphate fertilizer (fertile 2) at three
levels of 0, 100, 200 g/ha; second, triple super phosphate chemical
fertilizer at three levels of 0, 60, 90 kg/ha of pure phosphorus (P2O5).
The obtained results indicated that fertilizer treatments had a
significant effect on some morphological traits at 1% probability
level. In this regard, P2B2 treatment (100 g/ha biological phosphate
fertilizer (fertile 2) and 60 kg/ha triple super phosphate fertilizer) had
the greatest plant height, stem diameter, number of leaves and ear
length. It seems that in Ahvaz weather conditions, decrease of
consumption of triple superphosphate chemical fertilizer to less than
a half along with the consumption of biological phosphate fertilizer
(fertile 2) is highly important in order to achieve optimal results.
Therefore, it can be concluded that biological fertilizers can be used
as a suitable substitute for some of the chemical fertilizers in
sustainable agricultural systems.
Abstract: An experimental investigation is carried out to
establish the performance characteristics of a compression ignition
engine while using cerium oxide nanoparticles as additive in neat
diesel and diesel-biodiesel blends. In the first phase of the
experiments, stability of neat diesel and diesel-biodiesel fuel blends
with the addition of cerium oxide nanoparticles is analyzed. After
series of experiments, it is found that the blends subjected to high
speed blending followed by ultrasonic bath stabilization improves the
stability. In the second phase, performance characteristics are studied
using the stable fuel blends in a single cylinder four stroke engine
coupled with an electrical dynamometer and a data acquisition
system. The cerium oxide acts as an oxygen donating catalyst and
provides oxygen for combustion. The activation energy of cerium
oxide acts to burn off carbon deposits within the engine cylinder at
the wall temperature and prevents the deposition of non-polar
compounds on the cylinder wall results reduction in HC emissions.
The tests revealed that cerium oxide nanoparticles can be used as
additive in diesel and diesel-biodiesel blends to improve complete
combustion of the fuel significantly.
Abstract: The use of engineered nanomaterials has increased as
a result of their positive impact on many sectors of the economy,
including agriculture. Silver nanoparticles (AgNPs) are now used to
enhance seed germination, plant growth, and photosynthetic quantum
efficiency and as antimicrobial agents to control plant diseases. In
this study, we examined the effect of AgNP dosage on the seed
germination of three plant species: corn (Zea mays L.), watermelon
(Citrullus lanatus [Thunb.] Matsum. & Nakai) and zucchini
(Cucurbita pepo L.). This experiment was designed to study the
effect of AgNPs on germination percentage, germination rate, mean
germination time, root length and fresh and dry weight of seedlings
for the three species. Seven concentrations (0.05, 0.1, 0.5, 1, 1.5, 2
and 2.5 mg/ml) of AgNPs were examined at the seed germination
stage. The three species had different dose responses to AgNPs in
terms of germination parameters and the measured growth
characteristics. The germination rates of the three plants were
enhanced in response to AgNPs. Significant enhancement of the
germination percentage values was observed after treatment of the
watermelon and zucchini plants with AgNPs in comparison with
untreated seeds. AgNPs showed a toxic effect on corn root
elongation, whereas watermelon and zucchini seedling growth were
positively affected by certain concentrations of AgNPs. This study
showed that exposure to AgNPs caused both positive and negative
effects on plant growth and germination.
Abstract: The current paper presents an extensive bottom-up
framework for assessing building sector-specific vulnerability to
climate change: energy supply and demand. The research focuses on
the application of downscaled seasonal models for estimating energy
performance of buildings in Greece. The ARW-WRF model has
been set-up and suitably parameterized to produce downscaled
climatological fields for Greece, forced by the output of the CFSv2
model. The outer domain, D01/Europe, included 345 x 345 cells of
horizontal resolution 20 x 20 km2 and the inner domain, D02/Greece,
comprised 180 x 180 cells of 5 x 5 km2 horizontal resolution. The
model run has been setup for a period with a forecast horizon of 6
months, storing outputs on a six hourly basis.