Abstract: The development and extension of large cities induced
a need for shallow tunnel in soft ground of building areas. Estimation
of ground settlement caused by the tunnel excavation is important
engineering point. In this paper, prediction of surface subsidence
caused by tunneling in one section of seventh line of Tehran subway
is considered. On the basis of studied geotechnical conditions of the
region, tunnel with the length of 26.9km has been excavated applying
a mechanized method using an EPB-TBM with a diameter of 9.14m.
In this regard, settlement is estimated utilizing both analytical and
numerical finite element method. The numerical method shows that
the value of settlement in this section is 5cm. Besides, the analytical
consequences (Bobet and Loganathan-Polous) are 5.29 and 12.36cm,
respectively. According to results of this study, due tosaturation of
this section, there are good agreement between Bobet and numerical
methods. Therefore, tunneling processes in this section needs a
special consolidation measurement and support system before the
passage of tunnel boring machine.
Abstract: This study analyzed environmental health risks and
people-s perceptions of risks related to waste management in poor
settlements of Abidjan, to develop integrated solutions for health and
well-being improvement. The trans-disciplinary approach used relied
on remote sensing, a geographic information system (GIS),
qualitative and quantitative methods such as interviews and a
household survey (n=1800). Mitigating strategies were then
developed using an integrated participatory stakeholder workshop.
Waste management deficiencies resulting in lack of drainage and
uncontrolled solid and liquid waste disposal in the poor settlements
lead to severe environmental health risks. Health problems were
caused by direct handling of waste, as well as through broader
exposure of the population. People in poor settlements had little
awareness of health risks related to waste management in their
community and a general lack of knowledge pertaining to sanitation
systems. This unfortunate combination was the key determinant
affecting the health and vulnerability. For example, an increased
prevalence of malaria (47.1%) and diarrhoea (19.2%) was observed
in the rainy season when compared to the dry season (32.3% and
14.3%). Concerted and adapted solutions that suited all the
stakeholders concerned were developed in a participatory workshop
to allow for improvement of health and well-being.
Abstract: The present paper presents a finite element model and
analysis for the interaction between a piezoresistive tactile sensor and
biological tissues. The tactile sensor is proposed for use in minimally
invasive surgery to deliver tactile information of biological tissues to
surgeons. The proposed sensor measures the relative hardness of soft
contact objects as well as the contact force. Silicone rubbers were
used as the phantom of biological tissues. Finite element analysis of
the silicone rubbers and the mechanical structure of the sensor were
performed using COMSOL Multiphysics (v3.4) environment. The
simulation results verify the capability of the sensor to be used to
differentiate between different kinds of silicone rubber materials.
Abstract: Nowadays, the challenge in hydraulic turbine design is
the multi-objective design of turbine runner to reach higher
efficiency. The hydraulic performance of a turbine is strictly depends
on runner blades shape. The present paper focuses on the application
of the multi-objective optimization algorithm to the design of a small
Francis turbine runner. The optimization exercise focuses on the
efficiency improvement at the best efficiency operating point (BEP)
of the GAMM Francis turbine. A global optimization method based
on artificial neural networks (ANN) and genetic algorithms (GA)
coupled by 3D Navier-Stokes flow solver has been used to improve
the performance of an initial geometry of a Francis runner. The
results show the good ability of optimization algorithm and the final
geometry has better efficiency with initial geometry. The goal was to
optimize the geometry of the blades of GAMM turbine runner which
leads to maximum total efficiency by changing the design parameters
of camber line in at least 5 sections of a blade. The efficiency of the
optimized geometry is improved from 90.7% to 92.5%. Finally,
design parameters and the way of selection have been considered and
discussed.
Abstract: The necessity of updating the numerical models inputs, because of geometrical and resistive variations in rivers subject to solid transport phenomena, requires detailed control and monitoring activities. The human employment and financial resources of these activities moves the research towards the development of expeditive methodologies, able to evaluate the outflows through the measurement of more easily acquirable sizes. Recent studies highlighted the dependence of the entropic parameter on the kinematical and geometrical flow conditions. They showed a meaningful variability according to the section shape, dimension and slope. Such dependences, even if not yet well defined, could reduce the difficulties during the field activities, and also the data elaboration time. On the basis of such evidences, the relationships between the entropic parameter and the geometrical and resistive sizes, obtained through a large and detailed laboratory experience on steady free surface flows in conditions of macro and intermediate homogeneous roughness, are analyzed and discussed.
Abstract: In the literature of fuzzy measures, there exist many
well known parametric and non-parametric measures, each with its
own merits and limitations. But our main emphasis is on
applications of these measures to a variety of disciplines. To extend
the scope of applications of these fuzzy measures to geometry, we
need some special fuzzy measures. In this communication, we have
introduced two new fuzzy measures involving trigonometric
functions and simultaneously provided their applications to obtain
the basic results already existing in the literature of geometry.
Abstract: In this paper, a tooth shape optimization method for
cogging torque reduction in Permanent Magnet (PM) motors is
developed by using the Reduced Basis Technique (RBT) coupled by
Finite Element Analysis (FEA) and Design of Experiments (DOE)
methods. The primary objective of the method is to reduce the
enormous number of design variables required to define the tooth
shape. RBT is a weighted combination of several basis shapes. The
aim of the method is to find the best combination using the weights
for each tooth shape as the design variables. A multi-level design
process is developed to find suitable basis shapes or trial shapes at
each level that can be used in the reduced basis technique. Each level
is treated as a separated optimization problem until the required
objective – minimum cogging torque – is achieved. The process is
started with geometrically simple basis shapes that are defined by
their shape co-ordinates. The experimental design of Taguchi method
is used to build the approximation model and to perform
optimization. This method is demonstrated on the tooth shape
optimization of a 8-poles/12-slots PM motor.
Abstract: Given the motivation of maps impact in enhancing the
perception of the quality of life in a region, this work examines the
use of spatial analytical techniques in exploring the role of space in
shaping human development patterns in Assiut governorate.
Variations of human development index (HDI) of the governorate-s
villages, districts and cities are mapped using geographic information
systems (GIS). Global and local spatial autocorrelation measures are
employed to assess the levels of spatial dependency in the data and to
map clusters of human development. Results show prominent
disparities in HDI between regions of Assiut. Strong patterns of
spatial association were found proving the presence of clusters on the
distribution of HDI. Finally, the study indicates several "hot-spots" in
the governorate to be area of more investigations to explore the
attributes of such levels of human development. This is very
important for accomplishing the development plan of poorest regions
currently adopted in Egypt.
Abstract: Day by day technology increases and problems
associated with this technology also increase. Several researches
were carried out to investigate the deployment of such material safely
in geotechnical engineering in particular and civil engineering in
general. However, different types of waste material have such as
cement duct, fly ash and slag been proven to be suitable in several
applications. In this research cement dust mixed with different
percentages of sand will be used in some civil engineering
application as will be explained later in this paper throughout filed
and laboratory test. The used mixer (waste material with sand) prove
high performance, durability to environmental condition, low cost
and high benefits. At higher cement dust ratio, small cement ratio is
valuable for compressive strength and permeability. Also at small
cement dust ratio higher cement ratio is valuable for compressive
strength.
Abstract: The distribution, enrichment, and accumulation of zinc
(Zn) in the sediments of Kaohsiung Ocean Disposal Site (KODS),
Taiwan were investigated. Sediment samples from two outer disposal
site stations and nine disposed stations in the KODS were collected per
quarterly in 2009 and characterized for Zn, aluminum, organic matter,
and grain size. Results showed that the mean Zn concentrations varied
from 48 mg/kg to 456 mg/kg. Results from the enrichment factor (EF)
and geo-accumulation index (Igeo) analyses imply that the sediments
collected from the KODS can be characterized between moderate and
moderately severe degree enrichment and between none and none to
medium accumulation of Zn, respectively. However, results of
potential ecological risk index indicate that the sediment has low
ecological potential risk. The EF, Igeo, and Zn concentrations at the
disposed stations were slightly higher than those at outer disposal site.
This indicated that the disposed area centers may be subjected to the
disposal impaction of harbor dredged sediments.
Abstract: In image processing and visualization, comparing two
bitmapped images needs to be compared from their pixels by matching
pixel-by-pixel. Consequently, it takes a lot of computational time
while the comparison of two vector-based images is significantly
faster. Sometimes these raster graphics images can be approximately
converted into the vector-based images by various techniques. After
conversion, the problem of comparing two raster graphics images
can be reduced to the problem of comparing vector graphics images.
Hence, the problem of comparing pixel-by-pixel can be reduced to
the problem of polynomial comparisons. In computer aided geometric
design (CAGD), the vector graphics images are the composition of
curves and surfaces. Curves are defined by a sequence of control
points and their polynomials. In this paper, the control points will be
considerably used to compare curves. The same curves after relocated
or rotated are treated to be equivalent while two curves after different
scaled are considered to be similar curves. This paper proposed an
algorithm for comparing the polynomial curves by using the control
points for equivalence and similarity. In addition, the geometric
object-oriented database used to keep the curve information has also
been defined in XML format for further used in curve comparisons.
Abstract: The article describes a case study on one of Czech
Republic-s manufacturing middle size enterprises (ME), where due to
the European financial crisis, production lines had to be redesigned
and optimized in order to minimize the total costs of the production
of goods. It is considered an optimization problem of minimizing the
total cost of the work load, according to the costs of the possible
locations of the workplaces, with an application of the Greedy
algorithm and a partial analogy to a Set Packing Problem. The
displacement of working tables in a company should be as a one-toone
monotone increasing function in order for the total costs of
production of the goods to be at minimum. We use a heuristic
approach with greedy algorithm for solving this linear optimization
problem, regardless the possible greediness which may appear and
we apply it in a Czech ME.
Abstract: This study deals with Computational Fluid Dynamics
(CFD) studies of the interactions between the air flow and louvered
fins which equipped the automotive heat exchangers. 3D numerical
simulation results are obtained by using the ANSYS Fluent 13.0 code
and compared to experimental data. The paper studies the effect of
louver angle and louver pitch geometrical parameters, on overall
thermal hydraulic performances of louvered fins.
The comparison between CFD simulations and experimental data
show that established 3-D CFD model gives a good agreement. The
validation agrees, with about 7% of deviation respectively of friction
and Colburn factors to experimental results. As first, it is found that
the louver angle has a strong influence on the heat transfer rate. Then,
louver angle and louver pitch variation of the louvers and their effects
on thermal hydraulic performances are studied. In addition to this
study, it is shown that the second half of the fin takes has a
significant contribution on pressure drop increase without any
increase in heat transfer.
Abstract: The major purpose of this study is to use network and multimedia technologies to build a game-based learning system for junior high school students to apply in learning “World Geography" through the “role-playing" game approaches. This study first investigated the motivation and habits of junior high school students to use the Internet and online games, and then designed a game-based learning system according to situated and game-based learning theories. A teaching experiment was conducted to analyze the learning effectiveness of students on the game-based learning system and the major factors affecting their learning. A questionnaire survey was used to understand the students- attitudes towards game-based learning. The results showed that the game-based learning system can enhance students- learning, but the gender of students and their habits in using the Internet have no significant impact on learning. Game experience has a significant impact on students- learning, and the higher the experience value the better the effectiveness of their learning. The results of questionnaire survey also revealed that the system can increase students- motivation and interest in learning "World Geography".
Abstract: Tourism and coastal lines are the business sectors
since centuries especially in the European Nations and Albania is one
such spots. However, in recent decades tourism is experienced as
vulnerability of the surrounding ecological conditions of air, soil,
water, land and the communities that are dependant and sharing the
ecosystem among flora and fauna. Experts opine that apart from the
maintenance of near-originality of ecological biodiversity the tourism
rather known as ecotourism an indigenous socio-cultural
maintenance of indigenous/traditional knowledge of the local people
must be well cared in order to sustain on sustainable grounds. As a
general tendency, growth of tourism has been affected by the deterioration in the economic conditions on one aspect and unsustainable ecological areas affected since human interventions
earlier to this has negative impact on futuristic tourist spots. However, tourism in Albania as of now is 11% of GDP and coastal regions accounting to 2-4%. An amicable Mediterranean
climate with 300 sunny days similar parameters of Greece and Spain
throws up sustainable ecotourism in future decades provided public services namely, transportation, road safety, lodging, food
availability, recreational regiments, banking accessibility are as per
the World Tourism Organizations- protocols. Thus as of Albanian
situation, classification of ecotourism activities to safe-guard the localities with its maintenance of ecological land, water and climate
has become a paramount importance with a wanting and satisfactory options through harnessing human energy for profit and fitness of
ecological flora and fauna. A check on anthropogenic wastes and
their safer utilizations inclusive of agricultural and industrial
operations in line with Lalzi Bay Coastal Line are of utmost importance for the reason that the Adriatic Sea Coast is the one long
stretch of Albanian Lifeline. The present work is based on the methodology of the sustainable management of the same issue.
Abstract: The quest of providing more secure identification
system has led to a rise in developing biometric systems. Dorsal
hand vein pattern is an emerging biometric which has attracted the
attention of many researchers, of late. Different approaches have
been used to extract the vein pattern and match them. In this work,
Principle Component Analysis (PCA) which is a method that has
been successfully applied on human faces and hand geometry is
applied on the dorsal hand vein pattern. PCA has been used to obtain
eigenveins which is a low dimensional representation of vein pattern
features. Low cost CCD cameras were used to obtain the vein
images. The extraction of the vein pattern was obtained by applying
morphology. We have applied noise reduction filters to enhance the
vein patterns. The system has been successfully tested on a database
of 200 images using a threshold value of 0.9. The results obtained are
encouraging.
Abstract: This study uses GIS (Geographic Information
Systems) to conduct an evaluation of the degree of the sufficiency of
public green spaces such as parks and urban green areas as an
indicator of the density of metropolitan areas, in particular the Chubu
metropolitan area, in Japan. To that end, it first grasps the distribution
situation of green spaces in the three metropolitan areas in Japan,
especially in the Chubu metropolitan area, using GIS digital maps.
And based on this result, it conducts a GIS evaluation of the degree of
sufficiency of public green spaces and arranges the result for every
distance belt from the central part to compare and exam for every
distance belt away from the center in the Chubu metropolitan area.
Furthermore, after pointing out the insufficient areas of public green
spaces based on the result, it also proposes the improvement policy
which can be introduced in the Chubu metropolitan area.
Abstract: In this study, an OCR system for segmentation,
feature extraction and recognition of Ottoman Scripts has been
developed using handwritten characters. Detection of handwritten
characters written by humans is a difficult process. Segmentation and
feature extraction stages are based on geometrical feature analysis,
followed by the chain code transformation of the main strokes of
each character. The output of segmentation is well-defined segments
that can be fed into any classification approach. The classes of main
strokes are identified through left-right Hidden Markov Model
(HMM).
Abstract: A numerical study is presented on convective heat transfer in enclosures. The results are addressed to automotive headlights containing new-age light sources like Light Emitting Diodes (LED). The heat transfer from the heat source (LED) to the enclosure walls is investigated for mixed convection as interaction of the forced convection flow from an inlet and an outlet port and the natural convection at the heat source. Unlike existing studies, inlet and outlet port are thermally coupled and do not serve to remove hot fluid. The input power of the heat source is expressed by the Rayleigh number. The internal position of the heat source, the aspect ratio of the enclosure, and the inclination angle of one wall are varied. The results are given in terms of the global Nusselt number and the enclosure Nusselt number that characterize the heat transfer from the source and from the interior fluid to the enclosure walls, respectively. It is found that the heat transfer from the source to the fluid can be maximized if the source is placed in the main stream from the inlet to the outlet port. In this case, the Reynolds number and heat source position have the major impact on the heat transfer. A disadvantageous position has been found where natural and forced convection compete each other. The overall heat transfer from the source to the wall increases with increasing Reynolds number as well as with increasing aspect ratio and decreasing inclination angle. The heat transfer from the interior fluid to the enclosure wall increases upon decreasing the aspect ratio and increasing the inclination angle. This counteracting behaviour is caused by the variation of the area of the enclosure wall. All mixed convection results are compared to the natural convection limit.
Abstract: In this paper, we introduce a new method for elliptical
object identification. The proposed method adopts a hybrid scheme
which consists of Eigen values of covariance matrices, Circular
Hough transform and Bresenham-s raster scan algorithms. In this
approach we use the fact that the large Eigen values and small Eigen
values of covariance matrices are associated with the major and minor
axial lengths of the ellipse. The centre location of the ellipse can be
identified using circular Hough transform (CHT). Sparse matrix
technique is used to perform CHT. Since sparse matrices squeeze zero
elements and contain a small number of nonzero elements they
provide an advantage of matrix storage space and computational time.
Neighborhood suppression scheme is used to find the valid Hough
peaks. The accurate position of circumference pixels is identified
using raster scan algorithm which uses the geometrical symmetry
property. This method does not require the evaluation of tangents or
curvature of edge contours, which are generally very sensitive to
noise working conditions. The proposed method has the advantages of
small storage, high speed and accuracy in identifying the feature. The
new method has been tested on both synthetic and real images.
Several experiments have been conducted on various images with
considerable background noise to reveal the efficacy and robustness.
Experimental results about the accuracy of the proposed method,
comparisons with Hough transform and its variants and other
tangential based methods are reported.