Abstract: The aim of this study is to compare abused and normal male students in Tehran guidance schools with emphasis on the co-dependency of their mothers. The method of this study is based on survey method and comparison (Ex-Post Facto). The method of sampling is also multi-stage cluster. Accordingly, we did sampling from secondary schools of education and training in Tehran, including 12 schools with levels of first, second and third. Each of the schools represents the three – high, medium and low- economic and social conditions. In the following, three classes from every school and 20 students from each class were randomly selected. By (CTQ) abused and normal students were separated that 670 children were recognized as normal and 50 children as abused. Then, 50 children were randomly selected from normal group and compared with abused group. Using Spanned-Fischer Co-dependency Scale, we compared mothers of abused and normal students. The results showed that mothers of the abused children have higher co- dependency average comparing to the mothers of the normal children.
Abstract: The main objective of this paper is to establish the relationship between models of state organization and the various types of collective identity expressed by the Spanish. The question of nationalism and identity ascription in Spain has always been a topic of special importance due to the presence in that country of territories where the population emits very different opinions of nationalist sentiment than the rest of Spain. The current situation of sovereignty challenge of Catalonia to the central government exemplifies the importance of the subject matter. In order to analyze this process of interrelation, we use a secondary data mining by applying the multiple correspondence analysis technique (MCA). As a main result a typology of four types of expression of collective identity based on models of State organization are shown, which are connected with the party position on this issue.
Abstract: This paper is a qualitative research report. A group of
students form a public university in a small town in Colombia
participated in this study which aimed at describing to what extend
the use of social ads, published on the internet, helped to develop
their critical thinking skills. Students’ productions, field notes, video
recordings and direct observation were the instruments and
techniques used by the researches in order to gather the data which
was analyzed under the principles of grounded theory and
triangulation. The implementation of social ads into the classroom
evidenced a noticeable improvement in students’ ability to interpret
and argue social issues, as well as, their self-improvement in oral and
written production in English, as a foreign language.
Abstract: Despite the benefits of innovation diffusion in the
South African public service, implementation thereof seems to be
problematic, particularly with regard to e-governance which would
enhance the quality of service delivery, especially accessibility,
choice, and mode of operation. This paper reports on differences
between the public service and the private sector in terms of
innovation diffusion. Innovation diffusion will be investigated to
explore identified obstacles that are hindering successful
implementation of e-governance. The research inquiry is underpinned
by the diffusion of innovation theory, which is premised on the
assumption that innovation has a distinct channel, time, and mode of
adoption within the organisation. A comparative thematic document
analysis was conducted to investigate organisational differences with
regard to innovation diffusion. A similar approach has been followed
in other countries, where the same conceptual framework has been
used to guide document analysis in studies in both the private and the
public sectors. As per the recommended conceptual framework, three
organisational characteristics were emphasised, namely the external
characteristics of the organisation, the organisational structure, and
the inherent characteristics of the leadership. The results indicated
that the main difference in the external characteristics lies in the
focus and the clientele of the private sector. With regard to
organisational structure, private organisations have veto power,
which is not the case in the public service. Regarding leadership,
similarities were observed in social and environmental responsibility
and employees’ attitudes towards immediate supervision. Differences
identified included risk taking, the adequacy of leadership
development, organisational approaches to motivation and
involvement in decision making, and leadership style. Due to the
organisational differences observed, it is recommended that
differentiated strategies be employed to ensure effective innovation
diffusion, and ultimately e-governance. It is recommended that the
results of this research be used to stimulate discussion on ways to
improve collaboration between the mentioned sectors, to capitalise on
the benefits of each sector.
Abstract: The purpose of this paper is to show how state plays a
regulatory role in the relations of distribution by analyzing tax and
expenditure in Turkey. This paper has two main arguments. First,
state intervenes in economic and social life via budget policies and
steers the relations of distribution within the scope of the
reproduction of the capital accumulation and legitimacy. Secondly, a
great amount of public expenditure benefits capital owners while
state gains its tax income mainly from low and middle income
groups.
Abstract: The importance of culture and tourism in the attractiveness and competitiveness of the countries is central, and many regions are evidencing their cultural assets, tangible and intangible, as a means to create comparative advantages in tourism and produce a distinctive place in response to the pressures of globalization. Culture and tourism are interlinked because of their obvious combination and growth potential. Cultural tourism is a crucial global tourism market with fast growing. Regions can develop significant relations between culture and tourism to increase their attractiveness as places to visit, live and invest, increasing their competitiveness. Accordingly, having new and creative approach to historical areas as cultural value-based destinations can improve their conditions to promote tourism. Furthermore, in 21st century, media become the most important factor affecting the development of urban cities, including public places. As a result of the digital revolution, re-imaging and re-linkage public places by media are essential to create more interactions between public spaces and users, interaction media display, and urban screens, one of the most important defined media. This interaction can transform the urban space from being neglected to be more interactive space with users, especially the pedestrians. The paper focuses on The Walled City of Famagusta. As many other historic quarters elsewhere in the world, is in a process, of decay and deterioration, and its functionally distinctive areas are severely threatened by physical, functional, locational, and image obsolescence at varying degrees. So the focus on the future development of this area through tourism promotion can be an appropriate decision for the monument enhancement of the spatial quality in Walled City of Famagusta. In this paper, it is aimed to identify the effects of these new digital factors to transform public spaces especially in historic urban areas to promote creative tourism. Accordingly, two different analysis methods are used as well as a theoretical review. The first is case study on site and the second is Close ended questionnaire, test many concepts raised in this paper. The physical analysis on site carried out in order to evaluate the walled city restoration for touristic purpose. Besides, theoretical review is done in order to provide background to the subject and cleared Factors to attract tourists.
Abstract: In this paper, a desiccant solar unit for air
conditioning and desalination is presented first. Secondly, a dynamic
modelling study of the desiccant wheel is developed. After that, a
simulation study and an experimental investigation of the behaviour
of desiccant wheel are developed. The experimental investigation is
done in the chamber of commerce in Freiburg-Germany. Indeed, the
variations of calculated and measured temperatures and specific
humidity of dehumidified and rejected air are presented where a good
agreement is found when comparing the model predictions with
experimental data under the considered range of operating conditions.
Finally, the study of the compartments of desalination and water
condensation shows that the unit can produce an acceptable quantity
of water at the same time of the air conditioning operation.
Abstract: This article considers the problems of economic growth
and Russian energy strategy. Also in this paper, the issues related to
the economic growth prospects of Russian were discussed. Russian
energy strategy without standing Russia`s stature in global energy
markets, at the current production and extraction rates, will not be able
to sustain its own production as well as fulfil its energy strategy.
Indeed, Russia’s energy sector suffers from a chronic lack of
investments which are necessary to modernize its energy supply
system. In recent years, especially since the international financial
crisis, Russia-EU energy cooperation has made substantive progress.
Recently the break-through progress has been made, resulting mainly
from long-term contributing factors between the countries and recent
international economic and political situation changes. Analytical
material presented in the article is intended for a more detailed or
substantive analysis related to foreign economic relations of the
countries and Russia as well.
Abstract: Community living adjacent to forests and Protected
Areas, especially in South Asian countries, have a common practice
in extracting resources for their living and livelihoods. This
extraction of resources, because the way it is done, destroys the biophysical
features of the area. Deforestation, wildlife poaching, illegal
logging, unauthorized hill cutting etc. are some of the serious issues
of concern for the sustainability of the natural resources that has a
direct impact on environment and climate as a whole. To ensure
community involvement in conservation initiatives of the state,
community based forest management, commonly known as Comanagement,
has been in practice in 6 South Asian countries. These
are -India, Nepal, Sri Lanka, Pakistan, Bhutan and Bangladesh.
Involving community in forestry management was initiated first in
Bangladesh in 1979 and reached as an effective co-management
approach through a several paradigm shifts. This idea of Comanagement
has been institutionalized through a Government Order
(GO) by the Ministry of Environment and Forests, Government of
Bangladesh on November 23, 2009. This GO clearly defines the
structure and functions of Co-management and its different bodies.
Bangladesh Forest Department has been working in association with
community to conserve and manage the Forests and Protected areas
of Bangladesh following this legal document. Demographically
young people constitute the largest segment of population in
Bangladesh. This group, if properly sensitized, can produce valuable
impacts on the conservation initiatives, both by community and
government. This study traced the major factors that motivate
community youths to work effectively with different tiers of comanagement
organizations in conservation of forests and Protected
Areas of Bangladesh. For the purpose of this study, 3 FGDs were
conducted with 30 youths from the community living around the
Protected Areas of Cox’s bazar, South East corner of Bangladesh,
who are actively involved in Co-management organizations. KII were
conducted with 5 key officials of Forest Department stationed at
Cox’s Bazar. 2 FGDs were conducted with the representatives of 7
Co-management organizations working in Cox’s Bazar region and
approaches of different community outreach activities conducted for
forest conservation by 3 private organizations and Projects have been
reviewed. Also secondary literatures were reviewed for the history
and evolution of Co-management in Bangladesh and six South Asian
countries. This study found that innovative community outreach
activities that are financed by public and private sectors involving
youths and community as a whole have played a pivotal role in
conservation of forests and Protected Areas of the region. This
approach can be replicated in other regions of Bangladesh as well as
other countries of South Asia where Co-Management exists in
practice.
Abstract: HMS Industrial Networks AB has been recognized as
one of the most innovative companies in the industrial
communication industry worldwide. The creation of their Anybus
innovation during the 1990s contributed considerably to the
company’s success. From inception, HMS’ employees were
innovating for the purpose of creating new business (the creation
phase). After the Anybus innovation, they began the process of
internationalization (the commercialization phase), which in turn led
them to concentrate on cost reduction, product quality, delivery
precision, operational efficiency, and increasing growth (the growth
phase). As a result of this transformation, performing new radical
innovations have become more complicated. The purpose of our research was to explore the dynamics of
innovation at HMS from the aspect of key actors, activities, and
events, over the three phases, in order to understand what led to the
creation of their Anybus innovation, and why it has become
increasingly challenging for HMS to create new radical innovations
for the future. Our research methodology was based on a longitudinal,
retrospective study from the inception of HMS in 1988 to 2014, a
single case study inspired by the grounded theory approach. We
conducted 47 interviews and collected 1 024 historical documents for
our research. Our analysis has revealed that HMS’ success in creating the
Anybus, and developing a successful business around the innovation,
was based on three main capabilities – cultivating customer relations
on different managerial and organizational levels, inspiring business
relations, and balancing complementary human assets for the purpose
of business creation. The success of HMS has turned the management’s attention away
from past activities of key actors, of their behavior, and how they
influenced and stimulated the creation of radical innovations.
Nowadays, they are rhetorically focusing on creativity and
innovation. All the while, their real actions put emphasis on growth,
cost reduction, product quality, delivery precision, operational
efficiency, and moneymaking. In the process of becoming an
international company, HMS gradually refocused. In so doing they
became profitable and successful, but they also forgot what made
them innovative in the first place. Fortunately, HMS’ management
has come to realize that this is the case and they are now in search of
recapturing innovation once again. Our analysis indicates that HMS’ management is facing several
barriers to innovation related path dependency and other lock-in
phenomena. HMS’ management has been captured, trapped in their
mindset and actions, by the success of the past. But now their future has to be secured, and they have come to realize that moneymaking is
not everything. In recent years, HMS’ management have begun to
search for innovation once more, in order to recapture their past
capabilities for creating radical innovations. In order to unlock their
managerial perceptions of customer needs and their counter-innovation
driven activities and events, to utilize the full potential of
their employees and capture the innovation opportunity for the future.
Abstract: The exploitation of flow pulsation in micro- and
mini-channels is a potentially useful technique for enhancing cooling
of high-end photonics and electronics systems. It is thought that
pulsation alters the thickness of the hydrodynamic and thermal
boundary layers, and hence affects the overall thermal resistance
of the heat sink. Although the fluid mechanics and heat transfer
are inextricably linked, it can be useful to decouple the parameters
to better understand the mechanisms underlying any heat transfer
enhancement. Using two-dimensional, two-component particle image
velocimetry, the current work intends to characterize the heat transfer
mechanisms in pulsating flow with a mean Reynolds number of
48 by experimentally quantifying the hydrodynamics of a generic
liquid-cooled channel geometry. Flows circulated through the test
section by a gear pump are modulated using a controller to achieve
sinusoidal flow pulsations with Womersley numbers of 7.45 and
2.36 and an amplitude ratio of 0.75. It is found that the transient
characteristics of the measured velocity profiles are dependent on the
speed of oscillation, in accordance with the analytical solution for
flow in a rectangular channel. A large velocity overshoot is observed
close to the wall at high frequencies, resulting from the interaction
of near-wall viscous stresses and inertial effects of the main fluid
body. The steep velocity gradients at the wall are indicative of
augmented heat transfer, although the local flow reversal may reduce
the upstream temperature difference in heat transfer applications.
While unsteady effects remain evident at the lower frequency, the
annular effect subsides and retreats from the wall. The shear rate at
the wall is increased during the accelerating half-cycle and decreased
during deceleration compared to steady flow, suggesting that the flow
may experience both enhanced and diminished heat transfer during
a single period. Hence, the thickness of the hydrodynamic boundary
layer is reduced for positively moving flow during one half of the
pulsation cycle at the investigated frequencies. It is expected that the
size of the thermal boundary layer is similarly reduced during the
cycle, leading to intervals of heat transfer enhancement.
Abstract: This paper investigates the effects of breaks in bonds,
breaks in the earthing system and breaks in earth wire on the rise of
the earth potential (EPR) in a substation and at the transmission tower
bases using various models of an L6 tower. Different approaches
were adopted to examine the integrity of the earthing system and the
terminal towers. These effects were investigated to see the associated
difference in the EPR magnitudes with respect to a healthy system at
various locations. Comparisons of the computed EPR magnitudes
were then made between the healthy and unhealthy system to detect
any difference. The studies were conducted at power frequency for a
uniform soil with different soil resistivities. It was found that full
breaks in the double bond of the terminal towers increase the EPR
significantly at the fault location, while they reduce EPR at the
terminal tower bases. A fault on the isolated section of the grid can
result in EPR values up to 8 times of those on a healthy system at
higher soil resistivities, provided that the extended earthing system
stays connected to the grid.
Abstract: Large scale Indian manufacturers started
implementing Six Sigma to their supply core to fulfill the endless
need of high quality products. As well, they initiated encouraging
their suppliers to apply the well-ascertain SS management practice
and kept no resource for supplier enterprises, generally small midsized
enterprises to think for the admittance of Six Sigma as a quality
promotion drive. There are many issues to study for requisite changes
before the introduction of Six Sigma in auto SMEs. This paper
converges on impeding factors while implementing SS drive and also
pinpoints the gains achieved through successful implementation. The
result of this study suggest some operational guidelines for effective
implementation of Six Sigma from evidences acquired through
research questionnaire and interviews with industrial professionals,
apportioned to assort auto sector mid-sized enterprises (MSEs) in
India.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: Smart metering and demand response are gaining
ground in industrial and residential applications. Smart Appliances
have been given concern towards achieving Smart home. The success
of Smart grid development relies on the successful implementation of
Information and Communication Technology (ICT) in power sector.
Smart Appliances have been the technology under development and
many new contributions to its realization have been reported in the
last few years. The role of ICT here is to capture data in real time,
thereby allowing bi-directional flow of information/data between
producing and utilization point; that lead a way for the attainment of
Smart appliances where home appliances can communicate between
themselves and provide a self-control (switch on and off) using the
signal (information) obtained from the grid. This paper depicts the
background on ICT for smart appliances paying a particular attention
to the current technology and identifying the future ICT trends for
load monitoring through which smart appliances can be achieved to
facilitate an efficient smart home system which promote demand
response program. This paper grouped and reviewed the recent
contributions, in order to establish the current state of the art and
trends of the technology, so that the reader can be provided with a
comprehensive and insightful review of where ICT for smart
appliances stands and is heading to. The paper also presents a brief
overview of communication types, and then narrowed the discussion
to the load monitoring (Non-intrusive Appliances Load Monitoring
‘NALM’). Finally, some future trends and challenges in the further
development of the ICT framework are discussed to motivate future
contributions that address open problems and explore new
possibilities.
Abstract: Cloud computing can reduce the start-up expenses of implementing EHR (Electronic Health Records). However, many of the healthcare institutions are yet to implement cloud computing due to the associated privacy and security issues. In this paper, we analyze the challenges and opportunities of implementing cloud computing in healthcare. We also analyze data of over 5000 US hospitals that use Telemedicine applications. This analysis helps to understand the importance of smart phones over the desktop systems in different departments of the healthcare institutions. The wide usage of smartphones and cloud computing allows ubiquitous and affordable access to the health data by authorized persons, including patients and doctors. Cloud computing will prove to be beneficial to a majority of the departments in healthcare. Through this analysis, we attempt to understand the different healthcare departments that may benefit significantly from the implementation of cloud computing.
Abstract: E-Learning enables the users to learn at anywhere at
any time. In E-Learning systems, authenticating the E-Learning user
has security issues. The usage of appropriate communication
networks for providing the internet connectivity for E-learning is
another challenge. WiMAX networks provide Broadband Wireless
Access through the Multicast Broadcast Service so these networks
can be most suitable for E-Learning applications. The authentication
of E-Learning user is vulnerable to session hijacking problems. The
repeated authentication of users can be done to overcome these
issues. In this paper, session based Profile Caching Authentication is
proposed. In this scheme, the credentials of E-Learning users can be
cached at authentication server during the initial authentication
through the appropriate subscriber station. The proposed cache based
authentication scheme performs fast authentication by using cached
user profile. Thus, the proposed authentication protocol reduces the
delay in repeated authentication to enhance the security in ELearning.
Abstract: Pain management is a question of quality of life and
an indicator for nursing quality. Chronic pain which is predominant
in oncology and palliative nursing situations is perceived today as a
multifactorial, individual emotional experience with specific
characteristics including the sociocultural dimension when dealing
with migrant patients. This dimension of chronic pain is of major
importance in professional nursing of migrant patients in hospices or
palliative care units. Objectives of the study are: 1. To find out more
about the sociocultural views on pain and nursing care, on customs
and nursing practices connected with pain of both Turkish Muslim
and German Christian women, 2. To improve individual and family
oriented nursing practice with view to sociocultural needs of patients
in severe pain in palliative care. In a qualitative-explorative comparative study 4 groups of women,
Turkish Muslims immigrants (4 from the first generation, 5 from the
second generation) and German Christian women of two generations
(5 of each age group) of the same age groups as the Turkish women
and with similar educational backgrounds were interviewed (semistructured
ethnographic interviews using Spradley, 1979) on their
perceptions and experiences of pain and nursing care within their
families. For both target groups the presentation will demonstrate the
following results in detail: Utterance of pain as well as “private” and
“public” pain vary within different societies and cultures. Permitted
forms of pain utterance are learned in childhood and determine
attitudes and expectations in adulthood. Language, especially when
metaphors and symbols are used, plays a major role for
misunderstandings. The sociocultural context of illness may include
specific beliefs that are important to the patients and yet seem more
than far-fetched from a biomedical perspective. Pain can be an
influential factor in family relationships where respect or hierarchies
do not allow the direct utterance of individual needs. Specific
resources are often, although not exclusively, linked to religious
convictions and are significantly helpful in reducing pain. The discussion will evaluate the results of the study with view to
the relevant literature and present nursing interventions and
instruments beyond medication that are helpful when dealing with
patients from various socio-cultural backgrounds in painful end-oflife
situations.
Abstract: Dan C. Lortie’s Schoolteacher: A sociological study is
one of the best works on the sociology of teaching since W. Waller’s
classic study. It is a book worthy of review. Following the tradition of
symbolic interactionists, Lortie demonstrated the qualities who studied
the occupation of teaching. Using several methods to gather effective
data, Lortie has portrayed the ethos of the teaching profession.
Therefore, the work is an important book on the teaching profession
and teacher culture. Though outstanding, Lortie’s work is also flawed
in that his perspectives and methodology were adopted largely from
symbolic interactionism. First, Lortie in his work analyzed many
points regarding teacher culture; for example, he was interested in
exploring “sentiment,” “cathexis,” and “ethos.” Thus, he was more a
psychologist than a sociologist. Second, symbolic interactionism led
him to discern the teacher culture from a micro view, thereby missing
the structural aspects. For example, he did not fully discuss the issue of
gender and he ignored the issue of race. Finally, following the
qualitative sociological tradition, Lortie employed many qualitative
methods to gather data but only foucused on obtaining and presenting
interview data. Moreover, he used measurement methods that were too
simplistic for analyzing quantitative data fully.
Abstract: Magnetic Resonance Imaging Contrast Agents
(MRI-CM) are significant in the clinical and biological imaging as
they have the ability to alter the normal tissue contrast, thereby
affecting the signal intensity to enhance the visibility and detectability
of images. Superparamagnetic Iron Oxide (SPIO) nanoparticles,
coated with dextran or carboxydextran are currently available for
clinical MR imaging of the liver. Most SPIO contrast agents are
T2 shortening agents and Resovist (Ferucarbotran) is one of a
clinically tested, organ-specific, SPIO agent which has a low
molecular carboxydextran coating. The enhancement effect of
Resovist depends on its relaxivity which in turn depends on factors
like magnetic field strength, concentrations, nanoparticle properties,
pH and temperature. Therefore, this study was conducted to
investigate the impact of field strength and different contrast
concentrations on enhancement effects of Resovist. The study
explored the MRI signal intensity of Resovist in the physiological
range of plasma from T2-weighted spin echo sequence at three
magnetic field strengths: 0.47 T (r1=15, r2=101), 1.5 T (r1=7.4,
r2=95), and 3 T (r1=3.3, r2=160) and the range of contrast
concentrations by a mathematical simulation. Relaxivities of r1 and r2
(L mmol-1 Sec-1) were obtained from a previous study and the selected
concentrations were 0.05, 0.06, 0.07, 0.08, 0.09, 0.1, 0.2, 0.3, 0.4, 0.5,
0.6, 0.7, 0.8, 0.9, 1.0, 2.0, and 3.0 mmol/L. T2-weighted images were
simulated using TR/TE ratio as 2000 ms /100 ms. According to the
reference literature, with increasing magnetic field strengths, the
r1 relaxivity tends to decrease while the r2 did not show any
systematic relationship with the selected field strengths. In parallel,
this study results revealed that the signal intensity of Resovist at lower
concentrations tends to increase than the higher concentrations. The
highest reported signal intensity was observed in the low field strength
of 0.47 T. The maximum signal intensities for 0.47 T, 1.5 T and 3 T
were found at the concentration levels of 0.05, 0.06 and 0.05 mmol/L,
respectively. Furthermore, it was revealed that, the concentrations
higher than the above, the signal intensity was decreased
exponentially. An inverse relationship can be found between the field
strength and T2 relaxation time, whereas, the field strength was
increased, T2 relaxation time was decreased accordingly. However,
resulted T2 relaxation time was not significantly different between
0.47 T and 1.5 T in this study. Moreover, a linear correlation of
transverse relaxation rates (1/T2, s–1) with the concentrations of
Resovist can be observed. According to these results, it can conclude
that the concentration of SPIO nanoparticle contrast agents and the
field strengths of MRI are two important parameters which can affect the signal intensity of T2-weighted SE sequence. Therefore, when MR
imaging those two parameters should be considered prudently.