Development of a Robot Assisted Centrifugal Casting Machine for Manufacturing Multi-Layer Journal Bearing and High-Tech Machine Components

Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.

Authors:

• Mohammad Syed Ali Molla
• Mohammed Azim
• Mohammad Esharuzzaman

Keywords:

• Casting
• cylinder liners
• journal bearing
• robot.

References:

[1] John Campbell, “Complete Casting Handbook”, Butterworth-
Heinemann, Langford Lane, Kidlington, Oxford OX5 IGB, UK, 1st
Edition, 2011.
[2] A.K. Chakrabarti, “Casting Technology and Cast Alloys”, Prentice-Hall
of India Pvt. Ltd., New Delhi- 110001, Edition- S2015.
[3] Ernest P. De Garmo; J. T. Black.; Ronald A. Kohser (2003), “Materials
and Processes in Manufacturing” (9th ed.), Wiley, p. 277, ISBN 0-471-
65653-4.
[4] E. Wernholt, “Multivariable Frequency Domain Identification of
Industrial Robots”, Division of Automatic Control; ISBN 978-91-85895-
72-4 ISSN 0345-7524.
[5] L.E. Bruzzone, R.M. Molfino, M. Zoppi, “Mechatronic design of a
parallel robot for high-speed, impedance-controlled manipulation” Proc.
of the 11th Mediterranean Conference on Control and Automation, June
18-20, 2003, Rhodes, Greece.
[6] Academons; “Robotics”, Written in 2002; Paper #027856.
[7] F. Lange and G. Hirzinger, "Stability Preserving Sensor-Based Control
for Robots with Positional Interface", IEEE International Conference on
Robots and Automation (ICRA2005), April 2005, Barcelona, Spain.
[8] L.E. Bruzzone, R.M. Molfino, M. Zoppi, G. Zurlo, “Experimental tests
on the prototype of an impedance controlled three-degree-of-freedom
parallel robot” Proceedings of RAAD’ 03, 12th International Workshop
on Robotics in Alpe-Adria-Danube Region.
[9] H. Flordal, D. Spensieri, K. Akesson, M. Fabian, “Supervision of
multiple industrial robots: optimal and collision free work cycles”
Control Applications, 2004. Proceedings of the 2004 IEEE International Conference; Volume 2, Issue, 2-4 Sept. 2004 Page(s): 1404 - 1409
Vol.2.