Abstract: This paper reviews the objectives, methods and results of previous studies on biodrying of solid waste in several countries. Biodrying of solid waste is a novel technology in developing countries such as in Malaysia where high moisture content in organic waste makes the segregation process for recycling purposes complicated and diminishes the calorific value for the use of fuel source. In addition, the high moisture content also encourages the breeding of vectors and disease-bearing animals. From the laboratory results, the average moisture content of organic waste, paper, plastics and metals are 58.17%, 37.93%, 29.79% and 1.03% respectively for UKM campus. Biodrying of solid waste is a simple method of waste treatment as well as a cost-efficient technology to dry the solid waste. The process depends on temperature monitoring and air flow control along with the natural biodegradable process of organic waste. This review shows that the biodrying of solid waste method has high potential in treatment and recycling of solid waste, be useful for biodrying study and implementation in Malaysia.
Abstract: The performance and the plasma created by a pulsed
magnetoplasmadynamic thruster for small satellite application is
studied to understand better the ablation and plasma propagation
processes occurring during the short-time discharge. The results can
be applied to improve the quality of the thruster in terms of efficiency,
and to tune the propulsion system to the needs required by the satellite
mission. Therefore, plasma measurements with a high-speed camera
and induction probes, and performance measurements of mass bit
and impulse bit were conducted. Values for current sheet propagation
speed, mean exhaust velocity and thrust efficiency were derived from
these experimental data. A maximum in current sheet propagation
was found by the high-speed camera measurements for a medium
energy input and confirmed by the induction probes. A quasilinear
tendency between the mass bit and the energy input, the current
action integral respectively, was found, as well as a linear tendency
between the created impulse and the discharge energy. The highest
mean exhaust velocity and thrust efficiency was found for the highest
energy input.
Abstract: This paper proposes a method, combining color and layout features, for identifying documents captured from low-resolution handheld devices. On one hand, the document image color density surface is estimated and represented with an equivalent ellipse and on the other hand, the document shallow layout structure is computed and hierarchically represented. Our identification method first uses the color information in the documents in order to focus the search space on documents having a similar color distribution, and finally selects the document having the most similar layout structure in the remaining of the search space.
Abstract: Economically transformers constitute one of the largest investments in a Power system. For this reason, transformer condition assessment and management is a high priority task. If a transformer fails, it would have a significant negative impact on revenue and service reliability. Monitoring the state of health of power transformers has traditionally been carried out using laboratory Dissolved Gas Analysis (DGA) tests performed at periodic intervals on the oil sample, collected from the transformers. DGA of transformer oil is the single best indicator of a transformer-s overall condition and is a universal practice today, which started somewhere in the 1960s. Failure can occur in a transformer due to different reasons. Some failures can be limited or prevented by maintenance. Oil filtration is one of the methods to remove the dissolve gases and prevent the deterioration of the oil. In this paper we analysis the DGA data by regression method and predict the gas concentration in the oil in the future. We bring about a comparative study of different traditional methods of regression and the errors generated out of their predictions. With the help of these data we can deduce the health of the transformer by finding the type of fault if it has occurred or will occur in future. Additional in this paper effect of filtration on the transformer health is highlight by calculating the probability of failure of a transformer with and without oil filtrating.
Abstract: Design and modeling of nonlinear systems require the
knowledge of all inside acting parameters and effects. An empirical
alternative is to identify the system-s transfer function from input and
output data as a black box model. This paper presents a procedure
using least squares algorithm for the identification of a feed drive
system coefficients in time domain using a reduced model based on
windowed input and output data. The command and response of the
axis are first measured in the first 4 ms, and then least squares are
applied to predict the transfer function coefficients for this
displacement segment. From the identified coefficients, the next
command response segments are estimated. The obtained results
reveal a considerable potential of least squares method to identify the
system-s time-based coefficients and predict accurately the command
response as compared to measurements.
Abstract: The purpose of the study was to determine if, among
32 brain injured adults in community rehabilitation programs, there is
a statistically significant relationship between the degree of severity
of brain injury and these adults- level of self-esteem and stress. The
researcher hypothesized there would be a statistically significant
difference and a statistically significant relationship in self-esteem
and stress levels among and TBI adults. A Pearson product moment
correlational analysis was implemented and results found a
statistically significant relationship between self-esteem and stress
levels. Future recommendations were suggested upon completion of
research.
Abstract: Lately, significant work in the area of Intelligent
Manufacturing has become public and mainly applied within the
frame of industrial purposes. Special efforts have been made in the
implementation of new technologies, management and control
systems, among many others which have all evolved the field. Aware
of all this and due to the scope of new projects and the need of
turning the existing flexible ideas into more autonomous and
intelligent ones, i.e.: Intelligent Manufacturing, the present paper
emerges with the main aim of contributing to the design and analysis
of the material flow in either systems, cells or work stations under
this new “intelligent" denomination. For this, besides offering a
conceptual basis in some of the key points to be taken into account
and some general principles to consider in the design and analysis of
the material flow, also some tips on how to define other possible
alternative material flow scenarios and a classification of the states a
system, cell or workstation are offered as well. All this is done with
the intentions of relating it with the use of simulation tools, for which
these have been briefly addressed with a special focus on the Witness
simulation package. For a better comprehension, the previous
elements are supported by a detailed layout, other figures and a few
expressions which could help obtaining necessary data. Such data and
others will be used in the future, when simulating the scenarios in the
search of the best material flow configurations.
Abstract: The objective of this paper is to construct a creativity
composite index designed to capture the growing role of creativity in
driving economic and social development for the 27 European Union
countries.
The paper proposes a new approach for the measurement of EU-27
creative potential and for determining its capacity to attract and
develop creative human capital. We apply a modified version of the
3T model developed by Richard Florida and Irene Tinagli for
constructing a Euro-Creativity Index. The resulting indexes establish
a quantitative base for policy makers, supporting their efforts to
determine the contribution of creativity to economic development.
Abstract: The effect of beak trimming on behavior of two strains
of Thai native pullets kept in floor pens was studied. Six general
activities (standing, crouching, moving, comforting, roosting, and
nesting), 6 beak related activities (preening, feeding, drinking,
pecking at inedible object, feather pecking, and litter pecking), and 4
agonistic activities (head pecking, threatening, avoiding, and fighting)
were measured twice a for 15 consecutive days, started when the
pullets were 19 wk old. It was found that beak trimmed pullets drank
more frequent (P
Abstract: Appropriate description of business processes through
standard notations has become one of the most important assets for
organizations. Organizations must therefore deal with quality faults
in business process models such as the lack of understandability and
modifiability. These quality faults may be exacerbated if business
process models are mined by reverse engineering, e.g., from existing
information systems that support those business processes. Hence,
business process refactoring is often used, which change the internal
structure of business processes whilst its external behavior is
preserved. This paper aims to choose the most appropriate set of
refactoring operators through the quality assessment concerning
understandability and modifiability. These quality features are
assessed through well-proven measures proposed in the literature.
Additionally, a set of measure thresholds are heuristically established
for applying the most promising refactoring operators, i.e., those that
achieve the highest quality improvement according to the selected
measures in each case.
Abstract: The paper presents a simple and an accurate formula
that has been developed for the conduction angle (δ) of a single
phase half-wave or full-wave controlled rectifier with RL load. This
formula can be also used for calculating the conduction angle (δ) in
case of A.C. voltage regulator with inductive load under
discontinuous current mode. The simulation results shows that the
conduction angle calculated from the developed formula agree very
well with that obtained from the exact solution arrived from the
iterative method. Applying the developed formula can reduce the
computational time and reduce the time for manual classroom
calculation. In addition, the proposed formula is attractive for real
time implementations.
Abstract: Pharmaceutical industries and effluents of sewage treatment plants are the main sources of residual pharmaceuticals in water resources. These emergent pollutants may adversely impact the biophysical environment. Pharmaceutical industries often generate wastewater that changes in characteristics and quantity depending on the used manufacturing processes. Carbamazepine (CBZ), {5Hdibenzo [b,f]azepine-5-carboxamide, (C15H12N2O)}, is a significant non-biodegradable pharmaceutical contaminant in the Jordanian pharmaceutical wastewater, which is not removed by the activated sludge processes in treatment plants. Activated carbon may potentially remove that pollutant from effluents, but the high cost involved suggests that more attention should be given to the potential use of low-cost materials in order to reduce cost and environmental contamination. Powders of Jordanian non-metallic raw materials namely, Azraq Bentonite (AB), Kaolinite (K), and Zeolite (Zeo) were activated (acid and thermal treatment) and evaluated by removing CBZ. The results of batch and column techniques experiments showed around 46% and 67% removal of CBZ respectively.
Abstract: An accurate and proficient artificial neural network
(ANN) based genetic algorithm (GA) is developed for predicting of
nanofluids viscosity. A genetic algorithm (GA) is used to optimize
the neural network parameters for minimizing the error between the
predictive viscosity and the experimental one. The experimental
viscosity in two nanofluids Al2O3-H2O and CuO-H2O from 278.15
to 343.15 K and volume fraction up to 15% were used from
literature. The result of this study reveals that GA-NN model is
outperform to the conventional neural nets in predicting the viscosity
of nanofluids with mean absolute relative error of 1.22% and 1.77%
for Al2O3-H2O and CuO-H2O, respectively. Furthermore, the results
of this work have also been compared with others models. The
findings of this work demonstrate that the GA-NN model is an
effective method for prediction viscosity of nanofluids and have
better accuracy and simplicity compared with the others models.
Abstract: The belief K-modes method (BKM) approach is a new
clustering technique handling uncertainty in the attribute values of
objects in both the cluster construction task and the classification one.
Like the standard version of this method, the BKM results depend on
the chosen initial modes. So, one selection method of initial modes
is developed, in this paper, aiming at improving the performances of
the BKM approach. Experiments with several sets of real data show
that by considered the developed selection initial modes method, the
clustering algorithm produces more accurate results.
Abstract: The performance of schedules released to a shop floor may greatly be affected by unexpected disruptions. Thus, this paper considers the flexible job shop scheduling problem when processing times of some operations are represented by a uniform distribution with given lower and upper bounds. The objective is to find a predictive schedule that can deal with this uncertainty. The paper compares two genetic approaches to obtain predictive schedule. To determine the performance of the predictive schedules obtained by both approaches, an experimental study is conducted on a number of benchmark problems.
Abstract: The main aim of this research is to develop a methodology to encourage people's awareness, knowledge and understanding on the participation of flood management for cultural heritage, as the cooperation and interaction among government section, private section, and public section through role-play gaming simulation theory. The format of this research is to develop Role-play gaming simulation from existing documents, game or role-playing from several sources and existing data of the research site. We found that role-play gaming simulation can be implemented to help improving the understanding of the existing problem and the impact of the flood on cultural heritage, and the role-play game can be developed into the tool to improve people's knowledge, understanding and awareness about people's participation for flood management on cultural heritage, moreover the cooperation among the government, private section and public section will be improved through the theory of role-play gaming simulation.
Abstract: The objective of this research is to study of microbial lipid production by locally photosynthetic microalgae and oleaginous yeast via integrated cultivation technique using CO2 emissions from yeast fermentation. A maximum specific growth rate of Chlorella sp. KKU-S2 of 0.284 (1/d) was obtained under an integrated cultivation and a maximum lipid yield of 1.339g/L was found after cultivation for 5 days, while 0.969g/L of lipid yield was obtained after day 6 of cultivation time by using CO2 from air. A high value of volumetric lipid production rate (QP, 0.223 g/L/d), specific product yield (YP/X, 0.194), volumetric cell mass production rate (QX, 1.153 g/L/d) were found by using ambient air CO2 coupled with CO2 emissions from yeast fermentation. Overall lipid yield of 8.33 g/L was obtained (1.339 g/L of Chlorella sp. KKU-S2 and 7.06g/L of T. maleeae Y30) while low lipid yield of 0.969g/L was found using non-integrated cultivation technique. To our knowledge this is the unique report about the lipid production from locally microalgae Chlorella sp. KKU-S2 and yeast T. maleeae Y30 in an integrated technique to improve the biomass and lipid yield by using CO2 emissions from yeast fermentation.
Abstract: As the gradual increase of the enterprise scale, the
firms may possess many manufacturing plants located in different
places geographically. This change will result in the multi-site
production planning problems under the environment of multiple
plants or production resources. Our research proposes the structural
framework to analyze the multi-site planning problems. The analytical
framework is composed of six elements: multi-site conceptual model,
product structure (bill of manufacturing), production strategy,
manufacturing capability and characteristics, production planning
constraints, and key performance indicators. As well as the discussion
of these six ingredients, we also review related literatures in this paper
to match our analytical framework. Finally we take a real-world
practical example of a TFT-LCD manufacturer in Taiwan to explain
our proposed analytical framework for the multi-site production
planning problems.
Abstract: Short Message Service (SMS) has grown in
popularity over the years and it has become a common way of
communication, it is a service provided through General System
for Mobile Communications (GSM) that allows users to send text
messages to others.
SMS is usually used to transport unclassified information, but
with the rise of mobile commerce it has become a popular tool for
transmitting sensitive information between the business and its
clients. By default SMS does not guarantee confidentiality and
integrity to the message content.
In the mobile communication systems, security (encryption)
offered by the network operator only applies on the wireless link.
Data delivered through the mobile core network may not be
protected. Existing end-to-end security mechanisms are provided
at application level and typically based on public key
cryptosystem.
The main concern in a public-key setting is the authenticity of
the public key; this issue can be resolved by identity-based (IDbased)
cryptography where the public key of a user can be derived
from public information that uniquely identifies the user.
This paper presents an encryption mechanism based on the IDbased
scheme using Elliptic curves to provide end-to-end security
for SMS. This mechanism has been implemented over the standard
SMS network architecture and the encryption overhead has been
estimated and compared with RSA scheme. This study indicates
that the ID-based mechanism has advantages over the RSA
mechanism in key distribution and scalability of increasing
security level for mobile service.