Abstract: Solutions for the temperature profile around a moving
heat source are obtained using both analytic and finite element
(FEM) methods. Analytic and FEM solutions are applied to study the
temperature profile in welding. A moving heat source is represented
using both point heat source and uniform distributed disc heat source
models. Analytic solutions are obtained by solving the partial
differential equation for energy conservation in a solid, and FEM
results are provided by simulating welding using the ANSYS
software. Comparison is made for quasi steady state conditions. The
results provided by the analytic solutions are in good agreement with
results obtained by FEM.
Abstract: A number of routing algorithms based on learning
automata technique have been proposed for communication
networks. How ever, there has been little work on the effects of
variation of graph scarcity on the performance of these algorithms. In
this paper, a comprehensive study is launched to investigate the
performance of LASPA, the first learning automata based solution to
the dynamic shortest path routing, across different graph structures
with varying scarcities. The sensitivity of three main performance
parameters of the algorithm, being average number of processed
nodes, scanned edges and average time per update, to variation in
graph scarcity is reported. Simulation results indicate that the LASPA
algorithm can adapt well to the scarcity variation in graph structure
and gives much better outputs than the existing dynamic and fixed
algorithms in terms of performance criteria.
Abstract: The problem of exponential stability and periodicity for a class of cellular neural networks (DCNNs) with time-varying delays is investigated. By dividing the network state variables into subgroups according to the characters of the neural networks, some sufficient conditions for exponential stability and periodicity are derived via the methods of variation parameters and inequality techniques. These conditions are represented by some blocks of the interconnection matrices. Compared with some previous methods, the method used in this paper does not resort to any Lyapunov function, and the results derived in this paper improve and generalize some earlier criteria established in the literature cited therein. Two examples are discussed to illustrate the main results.
Abstract: Knee joint forces are available by in vivo measurement
using an instrumented knee prosthesis for small to moderate knee
flexion but not for high flexion yet. We created a 2D mathematical
model of the lower limb incorporating several new features such as a
patello-femoral mechanism, a thigh-calf contact at high knee flexion
and co-contracting muscles' force ratio, then used it to determine knee
joint forces arising from high knee flexions in four kneeling
conditions: rising with legs in parallel, with one foot forward, with or
without arm use. With arms used, the maximum values of knee joint
force decreased to about 60% of those with arms not used. When rising
with one foot forward, if arms are not used, the forward leg sustains a
force as large as that sustained when rising with legs parallel.
Abstract: An attempt has been made to determine the strength
and impact properties of Cr-Mo steel weld and base materials by
varying the current during manual metal arc welding. Toughness over
a temperature range from -32 to 100°C of base, heat affected zone
(HAZ) and weld zones at three current settings are made. It is
observed that the deterioration in notch toughness at any zone with
the temperature decreases. The values of notch toughness for all
zones at -32°C are almost same for any current settings. The values
of notch toughness at HAZ area are higher than that of weld area due
to the coarsening of ferrite grain of HAZ occurs with higher heat
input. From microhardness and microstructure result, it can be
concluded that large inclusion content in weld deposit is the cause of
lower notch toughness value.
Abstract: Air quality studies were carried out in the towns of
Putrajaya, Petaling Jaya and Nilai in the Malaysian Peninsular. In this
study, the variations of Ozone (O3) concentrations over a four year
period (2008-2011) were investigated using data obtained from the
Malaysian Department of the Environment (DOE). This study aims to
identify and describe the daily and monthly variations of O3
concentrations at the monitoring sites mentioned. The SPPS program
(Statistical Package for the Social Science) was used to analyze this
data in order to obtain the variations of O3 and also to clarify the
relationship between the stations. The findings of the study revealed
that the highest concentration of O3 occurred during the midday and
afternoon (between 13:00-15:00 hrs). The comparison between
stations also showed that highest O3 concentrations were recorded in
Putrajaya. The comparisons of average and maximum concentrations
of O3 for the three stations showed that the strongest significant
correlation was recorded in the Petaling Jaya station with the value
R2= 0.667. Results from this study indicate that in the urban areas of
Peninsular Malaysia, the concentration of O3 depends on the
concentration of NOx. Furthermore, HYSPLIT back trajectories
(-72h) indicated that air-mass transport patterns can also influence the
O3 concentration in the areas studied.
Abstract: In order to investigate water deficit stress on 24 of
soybean (Glycine Max. L) cultivars and lines in temperate climate, an
experiment was conducted in Iran Seed and Plant Improvement
Institute. Stress levels were irrigation after evaporation of 50, 100,
150 mm water from pan, class A. Randomized Completely Block
Design was arranged for each stress levels. Some traits such as, node
number, plant height, pod number per area, grain number per pod,
grain number per area, 1000 grains weight, grain yield and harvest
index were measured. Results showed that water deficit stress had
significant effect on node number, plant height, pod number per area,
grain number per pod, grain number per area, 1000 grains weight and
harvest index. Also all of agronomic traits except harvest index
influenced significantly by cultivars and lines. The least and most
grain yield was belonged to Ronak X Williams and M41 x Clark
respectively.
Abstract: Currently searching through internet is very popular especially in a field of academic. A huge of educational information such as research papers are overload for user. So community-base web sites have been developed to help user search information more easily from process of customizing a web site to need each specifies user or set of user. In this paper propose to use association rule analyze the community group on research paper bookmarking. A set of design goals for community group frameworks is developed and discussed. Additionally Researcher analyzes the initial relation by using association rule discovery between the antecedent and the consequent of a rule in the groups of user for generate the idea to improve ranking search result and development recommender system.
Abstract: In this paper we ultra low-voltage and high speed CMOS domino logic. For supply voltages below 500mV the delay for a ultra low-voltage NAND2 gate is aproximately 10% of a complementary CMOS inverter. Furthermore, the delay variations due to mismatch is much less than for conventional CMOS. Differential domino gates for AND/NAND and OR/NOR operation are presented.
Abstract: A wireless sensor network with a large number of tiny sensor nodes can be used as an effective tool for gathering data in various situations. One of the major issues in wireless sensor networks is developing an energy-efficient routing protocol which has a significant impact on the overall lifetime of the sensor network. In this paper, we propose a novel hierarchical with static clustering routing protocol called Energy-Efficient Protocol with Static Clustering (EEPSC). EEPSC, partitions the network into static clusters, eliminates the overhead of dynamic clustering and utilizes temporary-cluster-heads to distribute the energy load among high-power sensor nodes; thus extends network lifetime. We have conducted simulation-based evaluations to compare the performance of EEPSC against Low-Energy Adaptive Clustering Hierarchy (LEACH). Our experiment results show that EEPSC outperforms LEACH in terms of network lifetime and power consumption minimization.
Abstract: In this research, a part of Aghche basin in Isfahan
province with an area about 2000 hectars, was chosen to be obtain
curve number coefficient runoff and W indicator in second Cook
method By using aerial photos 1968 and 1995, the satellite data of
the IRS in 2008. Then the process of land use changes in the period
of study and its effect on the changes of curve number (CN), W
indicator and surface runoff coefficient (C) of the basin was
investigated. These results showed that on the track of these land use
changes the weight averages curve number (CN), surface runoff
coefficient (C) and W indicator of the basin were increased to 0.92,
0.02 and 0.78 unit in the first period of study and 1.18, 0.03, 0.99
Unit in the second period of study respectively.
Abstract: Tungsten trioxide has been prepared by using P-PTA
as a precursor on alumina substrates by spin coating method.
Palladium introduced on WO3 film via electrolysis deposition by
using palladium chloride as catalytic precursor. The catalytic
precursor was introduced on the series of films with different
morphologies. X-ray diffractometry (XRD), Scanning electron
microscopy (SEM) and XPS were applied to analyze structure and
morphology of the fabricated thin films. Then we measured variation
of samples- electrical conductivity of pure and Pd added films in air
and diluted hydrogen. Addition of Pd resulted in a remarkable
improvement of the hydrogen sensing properties of WO3 by detection
of Hydrogen below 1% at room temperature. Also variation of the
electrical conductivity in the presence of diluted hydrogen revealed
that response of samples depends rather strongly on the palladium
configuration on the surface.
Abstract: Wind turbines with double output induction
generators can operate at variable speed permitting conversion
efficiency maximization over a wide range of wind velocities. This
paper presents the performance analysis of a wind driven double
output induction generator (DOIG) operating at varying shafts speed.
A periodic transient state analysis of DOIG equipped with two
converters is carried out using a hybrid induction machine model.
This paper simulates the harmonic content of waveforms in various
points of drive at different speeds, based on the hybrid model
(dqabc). Then the sinusoidal and trapezoidal pulse-width–modulation
control techniques are used in order to improve the power factor of
the machine and to weaken the injected low order harmonics to the
supply. Based on the frequency spectrum, total harmonics distortion,
distortion factor and power factor. Finally advantages of sinusoidal
and trapezoidal pulse width modulation techniques are compared.
Abstract: Semiconductor materials with coatings have a wide range of applications in MEMS and NEMS. This work uses transfermatrix method for calculating the radiative properties. Dopped silicon is used and the coherent formulation is applied. The Drude model for the optical constants of doped silicon is employed. Results showed that for the visible wavelengths, more emittance occurs in greater concentrations and the reflectance decreases as the concentration increases. In these wavelengths, transmittance is negligible. Donars and acceptors act similar in visible wavelengths. The effect of wave interference can be understood by plotting the spectral properties such as reflectance or transmittance of a thin dielectric film versus the film thickness and analyzing the oscillations of properties due to constructive and destructive interferences. But this effect has not been shown at visible wavelengths. At room temperature, the scattering process is dominated by lattice scattering for lightly doped silicon, and the impurity scattering becomes important for heavily doped silicon when the dopant concentration exceeds1018cm-3 .
Abstract: The increasing competitiveness in manufacturing
industry is forcing manufacturers to seek effective processing
schedules. The paper presents an optimization manufacture
scheduling approach for dependent details processing with given
processing sequences and times on multiple machines. By defining
decision variables as start and end moments of details processing it is
possible to use straightforward variables restrictions to satisfy
different technological requirements and to formulate easy to
understand and solve optimization tasks for multiple numbers of
details and machines. A case study example is solved for seven base
moldings for CNC metalworking machines processed on five
different machines with given processing order among details and
machines and known processing time-s duration. As a result of linear
optimization task solution the optimal manufacturing schedule
minimizing the overall processing time is obtained. The
manufacturing schedule defines the moments of moldings delivery
thus minimizing storage costs and provides mounting due-time
satisfaction. The proposed optimization approach is based on real
manufacturing plant problem. Different processing schedules variants
for different technological restrictions were defined and implemented
in the practice of Bulgarian company RAIS Ltd. The proposed
approach could be generalized for other job shop scheduling
problems for different applications.
Abstract: Whereas in the third generation nuclear reactors,
dimensions of core and also the kind of coolant and enrichment
percent of fuel have significantly changed than the second
generation, therefore in this article the aim is based on a
comparative investigation between two same power reactors of
second and third generations, that the neutronic parameters of both
reactors such as: K∞, Keff and its details and thermal hydraulic
parameters such as: power density, specific power, volumetric heat
rate, released power per fuel volume unit, volume and mass of clad
and fuel (consisting fissile and fertile fuels), be calculated and
compared together. By this comparing the efficiency and
modification of third generation nuclear reactors than second
generation which have same power can be distinguished.
In order to calculate the cited parameters, some information
such as: core dimensions, the pitch of lattice, the fuel matter, the
percent of enrichment and the kind of coolant are used. For
calculating the neutronic parameters, a neutronic program entitled:
SIXFAC and also related formulas have been used. Meantime for
calculating the thermal hydraulic and other parameters, analytical
method and related formulas have been applied.
Abstract: In this paper we present a general formalism for the
establishment of the family of selective regressor affine projection
algorithms (SR-APA). The SR-APA, the SR regularized APA (SR-RAPA),
the SR partial rank algorithm (SR-PRA), the SR binormalized
data reusing least mean squares (SR-BNDR-LMS), and the SR normalized
LMS with orthogonal correction factors (SR-NLMS-OCF)
algorithms are established by this general formalism. We demonstrate
the performance of the presented algorithms through simulations in
acoustic echo cancellation scenario.
Abstract: In recent years, many researches to mine the exploding Web world, especially User Generated Content (UGC) such as
weblogs, for knowledge about various phenomena and events in the physical world have been done actively, and also Web services
with the Web-mined knowledge have begun to be developed for
the public. However, there are few detailed investigations on how accurately Web-mined data reflect physical-world data. It must be
problematic to idolatrously utilize the Web-mined data in public Web services without ensuring their accuracy sufficiently. Therefore,
this paper introduces the simplest Web Sensor and spatiotemporallynormalized
Web Sensor to extract spatiotemporal data about a target
phenomenon from weblogs searched by keyword(s) representing the
target phenomenon, and tries to validate the potential and reliability of the Web-sensed spatiotemporal data by four kinds of granularity
analyses of coefficient correlation with temperature, rainfall, snowfall,
and earthquake statistics per day by region of Japan Meteorological
Agency as physical-world data: spatial granularity (region-s population
density), temporal granularity (time period, e.g., per day vs. per week), representation granularity (e.g., “rain" vs. “heavy rain"), and
media granularity (weblogs vs. microblogs such as Tweets).
Abstract: Automobile Industry has great importance in the
Spanish economy (8,7 % of the active Spanish population is
employed in this sector).The above mentioned sector has been one of
the principal sectors affected by the current economic crisis,
consistently, the budgets in advertising have been severely limited
(46,9 % less in the period of reference), these needs of reduction
have originated a substantial change in the advertising strategy (from
2007 the increase of the advertising investment in Internet is 251,6
%), and increase profitability. The growing use of social media by
consumers therefore makes online consumer conversations an
attractive additional format for Automobile firms to promote
products at a lower cost. This research analyzes the relation between
the activity in Social Media and the design in the car industry,
looking for relations between strategies of design based on Social
Media and sales and a channel of information for companies to know
what the consumer preferences. For this ongoing research we used a
longitudinal withdrawal of information has been used using
information of panel. Managerial and research implications of the
finding are discussed.
Abstract: Most electrical distribution systems are incurring large
losses as the loads are wide spread, inadequate reactive power
compensation facilities and their improper control. A typical static
VAR compensator consists of capacitor bank in binary sequential
steps operated in conjunction with a thyristor controlled reactor of the
smallest step size. This SVC facilitates stepless control of reactive
power closely matching with load requirements so as to maintain
power factor nearer to unity. This type of SVC-s requiring a
appropriately controlled TCR. This paper deals with an air cored
reactor suitable for distribution transformer of 3phase, 50Hz, Dy11,
11KV/433V, 125 KVA capacity. Air cored reactors are designed,
built, tested and operated in conjunction with capacitor bank in five
binary sequential steps. It is established how the delta connected TCR
minimizes the harmonic components and the operating range for
various electrical quantities as a function of firing angle is
investigated. In particular firing angle v/s line & phase currents, D.C.
components, THD-s, active and reactive powers, odd and even triplen
harmonics, dominant characteristic harmonics are all investigated and
range of firing angle is fixed for satisfactory operation. The harmonic
spectra for phase and line quantities at specified firing angles are
given. In case the TCR is operated within the bound specified in this
paper established through simulation studies are yielding the best
possible operating condition particularly free from all dominant
harmonics.