Abstract: In this paper electrical characteristics of various kinds
of multiple-gate silicon nanowire transistors (SNWT) with the
channel length equal to 7 nm are compared. A fully ballistic quantum
mechanical transport approach based on NEGF was employed to
analyses electrical characteristics of rectangular and cylindrical
silicon nanowire transistors as well as a Double gate MOS FET. A
double gate, triple gate, and gate all around nano wires were studied
to investigate the impact of increasing the number of gates on the
control of the short channel effect which is important in nanoscale
devices. Also in the case of triple gate rectangular SNWT inserting
extra gates on the bottom of device can improve the application of
device. The results indicate that by using gate all around structures
short channel effects such as DIBL, subthreshold swing and delay
reduces.
Abstract: Series of tellurite glass of the system 78TeO2-10PbO-
10Li2O-(2-x)Nd2O3-xEr2O3, where x = 0.5, 1.0, 1.5 and 2.0 was
successfully been made. A study of upconversion luminescence of
the Nd3+/Er3+ co-doped tellurite glass has been carried out. From
Judd-Ofelt analysis, the experimental lifetime, exp. τ of the glass
serie are found higher in the visible region as they varies from
65.17ms to 114.63ms, whereas in the near infrared region (NIR) the
lifetime are varies from 2.133ms to 2.270ms. Meanwhile, the
emission cross section,σ results are found varies from 0.004 x 1020
cm2 to 1.007 x 1020 cm2 with respect to composition. The emission
spectra of the glass are found been contributed from Nd3+ and Er3+
ions by which nine significant transition peaks are observed. The
upconversion mechanism of the co-doped tellurite glass has been
shown in the schematic energy diagrams. In this works, it is found
that the excited state-absorption (ESA) is still dominant in the
upconversion excitation process as the upconversion excitation
mechanism of the Nd3+ excited-state levels is accomplished through a
stepwise multiphonon process. An efficient excitation energy transfer
(ET) has been observed between Nd3+ as a donor and Er3+ as the
acceptor. As a result, respective emission spectra had been observed.
Abstract: Following the loss of NASA's Space Shuttle
Columbia in 2003, it was determined that problems in the agency's
organization created an environment that led to the accident. One
component of the proposed solution resulted in the formation of the
NASA Engineering Network (NEN), a suite of information retrieval
and knowledge-sharing tools. This paper describes the
implementation of communities of practice, which are formed along
engineering disciplines. Communities of practice enable engineers to
leverage their knowledge and best practices to collaborate and take
information learning back to their jobs and embed it into the
procedures of the agency. This case study offers insight into using
traditional engineering disciplines for virtual collaboration, including
lessons learned during the creation and establishment of NASA-s
communities.
Abstract: Current image-based individual human recognition
methods, such as fingerprints, face, or iris biometric modalities
generally require a cooperative subject, views from certain aspects,
and physical contact or close proximity. These methods cannot
reliably recognize non-cooperating individuals at a distance in the
real world under changing environmental conditions. Gait, which
concerns recognizing individuals by the way they walk, is a relatively
new biometric without these disadvantages. The inherent gait
characteristic of an individual makes it irreplaceable and useful in
visual surveillance.
In this paper, an efficient gait recognition system for human
identification by extracting two features namely width vector of
the binary silhouette and the MPEG-7-based region-based shape
descriptors is proposed. In the proposed method, foreground objects
i.e., human and other moving objects are extracted by estimating
background information by a Gaussian Mixture Model (GMM) and
subsequently, median filtering operation is performed for removing
noises in the background subtracted image. A moving target classification
algorithm is used to separate human being (i.e., pedestrian)
from other foreground objects (viz., vehicles). Shape and boundary
information is used in the moving target classification algorithm.
Subsequently, width vector of the outer contour of binary silhouette
and the MPEG-7 Angular Radial Transform coefficients are taken as
the feature vector. Next, the Principal Component Analysis (PCA)
is applied to the selected feature vector to reduce its dimensionality.
These extracted feature vectors are used to train an Hidden Markov
Model (HMM) for identification of some individuals. The proposed
system is evaluated using some gait sequences and the experimental
results show the efficacy of the proposed algorithm.
Abstract: To evaluate the ability to predict xerostomia after
radiotherapy, we constructed and compared neural network and
logistic regression models. In this study, 61 patients who completed a
questionnaire about their quality of life (QoL) before and after a full
course of radiation therapy were included. Based on this questionnaire,
some statistical data about the condition of the patients’ salivary
glands were obtained, and these subjects were included as the inputs of
the neural network and logistic regression models in order to predict
the probability of xerostomia. Seven variables were then selected from
the statistical data according to Cramer’s V and point-biserial
correlation values and were trained by each model to obtain the
respective outputs which were 0.88 and 0.89 for AUC, 9.20 and 7.65
for SSE, and 13.7% and 19.0% for MAPE, respectively. These
parameters demonstrate that both neural network and logistic
regression methods are effective for predicting conditions of parotid
glands.
Abstract: In this paper, Tobephobia (TBP) alludes to the fear of
failure experienced by teachers to manage curriculum change. TBP is
an emerging concept and it extends the boundaries of research in
terms of how we view achievement and failure in education.
Outcomes-based education (OBE) was introduced fifteen years ago
in South African schools without simultaneously upgrading teachers-
professional competencies. This exploratory research, therefore
examines a simple question: What is the impact of TBP and OBE on
teachers? Teacher ineptitude to cope with the OBE curriculum in the
classroom is a serious problem affecting large numbers of South
African teachers. This exploratory study sought to determine the
perceived negative impact of OBE and TBP on teachers. A survey
was conducted amongst 311 teachers in Port Elizabeth and Durban,
South Africa. The results confirm the very negative impact of TBP
and OBE on teachers. This exploratory study authenticates the
existence of TBP.
Abstract: This study demonstrates the use of Class F fly ash in
combination with lime or lime kiln dust in the full depth reclamation
(FDR) of asphalt pavements. FDR, in the context of this paper, is a
process of pulverizing a predetermined amount of flexible pavement
that is structurally deficient, blending it with chemical additives and
water, and compacting it in place to construct a new stabilized base
course. Test sections of two structurally deficient asphalt pavements
were reclaimed using Class F fly ash in combination with lime and
lime kiln dust. In addition, control sections were constructed using
cement, cement and emulsion, lime kiln dust and emulsion, and mill
and fill. The service performance and structural behavior of the FDR
pavement test sections were monitored to determine how the fly ash
sections compared to other more traditional pavement rehabilitation
techniques. Service performance and structural behavior were
determined with the use of sensors embedded in the road and Falling
Weight Deflectometer (FWD) tests. Monitoring results of the FWD
tests conducted up to 2 years after reclamation show that the cement,
fly ash+LKD, and fly ash+lime sections exhibited two year resilient
modulus values comparable to open graded cement stabilized
aggregates (more than 750 ksi). The cement treatment resulted in a
significant increase in resilient modulus within 3 weeks of
construction and beyond this curing time, the stiffness increase was
slow. On the other hand, the fly ash+LKD and fly ash+lime test
sections indicated slower shorter-term increase in stiffness. The fly
ash+LKD and fly ash+lime section average resilient modulus values
at two years after construction were in excess of 800 ksi. Additional
longer-term testing data will be available from ongoing pavement
performance and environmental condition data collection at the two
pavement sites.
Abstract: Waste corn pulp was investigated as a potential feedstock during vermicomposting using Eisenia fetida. Corn pulp is the major staple food in Southern Africa and constitutes about 25% of the total organic waste. Wastecooked corn pulp was blended with cow dung in the ratio 6:1 respectively to optimize the vermicomposting process. The feedstock was allowed to vermicompost for 30 days. The vermicomposting took place in a 3- tray plastic worm bin. Moisture content, temperature, pH, and electrical conductivity were monitoreddaily. The NPK content was determined at day 30. During vermicomposting, moisture content increased from 27.68% to 52.41%, temperature ranged between 19- 25◦C, pH increased from 5.5 to 7.7, and electrical conductivity decreased from 80000μS/cm to 60000μS/cm. The ash content increased from 11.40% to 28.15%; additionally the volatile matter increased from 1.45% to 10.02%. An odorless, dark brown vermicompost was obtained. The vermicompost NPK content was 4.19%, 1.15%, and 6.18% respectively.
Abstract: Many difficulties are faced in the process of learning
computer programming. This paper will propose a system framework
intended to reduce cognitive load in learning programming. In first
section focus is given on the process of learning and the
shortcomings of the current approaches to learning programming.
Finally the proposed prototype is suggested along with the
justification of the prototype. In the proposed prototype the concept
map is used as visualization metaphor. Concept maps are similar to
the mental schema in long term memory and hence it can reduce
cognitive load well. In addition other method such as part code
method is also proposed in this framework to can reduce cognitive
load.
Abstract: Fructooligosaccharides derived from microbial enzyme especially from fungal sources has been received particular attention due to its beneficial effects as prebiotics and mass production. However, fungal fermentation is always cumbersome due to its broth rheology problem that will eventually affect the production of FOS. This study investigated the efficiency of immobilized cell system using rotating fibrous bed bioreactor (RFBB) in producing fructooligosaccharides (FOS). A comparative picture with respect to conventional stirred tank bioreactor (CSTB) and RFBB has been presented. To demonstrate the effect of agitation intensity and aeration rate, a laboratory-scale bioreactor 2.5 L was operated in three phases (high, medium, low) for 48 hours. Agitation speed has a great influence on P. simplicissimum fermentation for FOS production, where the volumetric FOS productivity using RFBB is increased with almost 4 fold compared to the FOS productivity in CSTB that only 0.319 g/L/h. Rate of FOS production increased up to 1.2 fold when immobilized cells system was employed at aeration rate similar to the freely suspended cells at 2.0 vvm.
Abstract: In this study, active tendons with Proportional Integral
Derivation type controllers were applied to a SDOF and a MDOF
building model. Physical models of buildings were constituted with
virtual springs, dampers and rigid masses. After that, equations of
motion of all degrees of freedoms were obtained. Matlab Simulink
was utilized to obtain the block diagrams for these equations of
motion. Parameters for controller actions were found by using a trial
method. After earthquake acceleration data were applied to the
systems, building characteristics such as displacements, velocities,
accelerations and transfer functions were analyzed for all degrees of
freedoms. Comparisons on displacement vs. time, velocity vs. time,
acceleration vs. time and transfer function (Db) vs. frequency (Hz)
were made for uncontrolled and controlled buildings. The results
show that the method seems feasible.
Abstract: One problem of synthetic sunflower cultivation is an
erratic germination of the seeds. To improve the germination, presowing
seed treatment with an ultrasound was tested. All treatments
were carried out at 40 kHz frequency with the intensities of 40, 60,
80 and 100% of the ultrasonic generator total power (250 W) for the
durations of 5, 10, 15 and 20 minutes. Data on seed germination
percentage, seed vigor index (SVI), root and shoot lengths of
seedlings were collected. The results showed that germination, SVI,
root and shoot lengths of ultrasonic treated seedlings were different
from the control, depending on intensity of the ultrasound. The
effects of ultrasonic treatment were significant on germination,
resulting in a maximum increase of 43% at 40 and 60% intensities
compared to that of the control seeds. In addition, seedlings of these 2
treatments had higher SVI and longer root and shoot lengths than that
of the control seedlings. All treatment durations resulted in higher
germination and SVI, longer root and higher shoot lenghts of
seedlings than the control. Among the duration treatments, only SVI
and seedling root length were significantly different.
Abstract: Current research has explored the impact of
instructional immediacy, defined as those behaviors that help build
close relationships or feelings of closeness, both on cognition and
motivation in the traditional classroom and online classroom;
however, online courses continue to suffer from higher dropout rates.
Based on Albert Bandura-s Social Cognitive Theory, four primary
relationships or interactions in an online course will be explored in
light of how they can provide immediacy thereby reducing student
attrition and improving cognitive learning. The four relationships are
teacher-student, student-student, and student-content, and studentcomputer.
Results of a study conducted with inservice teachers
completing a 14-week online professional development technology
course will be examined to demonstrate immediacy strategies that
improve cognitive learning and reduce student attrition. Results of
the study reveal that students can be motivated through various
interactions and instructional immediacy behaviors which lead to
higher completion rates, improved self-efficacy, and cognitive
learning.
Abstract: The common bean is the most important grain legume for direct human consumption in the world and BCMV is one of the world's most serious bean diseases that can reduce yield and quality of harvested product. To determine the best tolerance index to BCMV and recognize tolerant genotypes, 2 experiments were conducted in field conditions. Twenty five common bean genotypes were sown in 2 separate RCB design with 3 replications under contamination and non-contamination conditions. On the basis of the results of indices correlations GMP, MP and HARM were determined as the most suitable tolerance indices. The results of principle components analysis indicated 2 first components totally explained 98.52% of variations among data. The first and second components were named potential yield and stress susceptible respectively. Based on the results of BCMV tolerance indices assessment and biplot analysis WA8563-4, WA8563-2 and Cardinal were the genotypes that exhibited potential seed yield under contamination and noncontamination conditions.
Abstract: The number of framework conceived for e-learning
constantly increase, unfortunately the creators of learning materials
and educational institutions engaged in e-formation adopt a
“proprietor" approach, where the developed products (courses,
activities, exercises, etc.) can be exploited only in the framework
where they were conceived, their uses in the other learning
environments requires a greedy adaptation in terms of time and
effort. Each one proposes courses whose organization, contents,
modes of interaction and presentations are unique for all learners,
unfortunately the latter are heterogeneous and are not interested by
the same information, but only by services or documents adapted to
their needs. Currently the new tendency for the framework
conceived for e-learning, is the interoperability of learning materials,
several standards exist (DCMI (Dublin Core Metadata Initiative)[2],
LOM (Learning Objects Meta data)[1], SCORM (Shareable Content
Object Reference Model)[6][7][8], ARIADNE (Alliance of Remote
Instructional Authoring and Distribution Networks for Europe)[9],
CANCORE (Canadian Core Learning Resource Metadata
Application Profiles)[3]), they converge all to the idea of learning
objects. They are also interested in the adaptation of the learning
materials according to the learners- profile. This article proposes an
approach for the composition of courses adapted to the various
profiles (knowledge, preferences, objectives) of learners, based on
two ontologies (domain to teach and educational) and the learning
objects.
Abstract: The topic of surface flattening plays a vital role in the field of computer aided design and manufacture. Surface flattening enables the production of 2D patterns and it can be used in design and manufacturing for developing a 3D surface to a 2D platform, especially in fashion design. This study describes surface flattening based on minimum energy methods according to the property of different fabrics. Firstly, through the geometric feature of a 3D surface, the less transformed area can be flattened on a 2D platform by geodesic. Then, strain energy that has accumulated in mesh can be stably released by an approximate implicit method and revised error function. In some cases, cutting mesh to further release the energy is a common way to fix the situation and enhance the accuracy of the surface flattening, and this makes the obtained 2D pattern naturally generate significant cracks. When this methodology is applied to a 3D mannequin constructed with feature lines, it enhances the level of computer-aided fashion design. Besides, when different fabrics are applied to fashion design, it is necessary to revise the shape of a 2D pattern according to the properties of the fabric. With this model, the outline of 2D patterns can be revised by distributing the strain energy with different results according to different fabric properties. Finally, this research uses some common design cases to illustrate and verify the feasibility of this methodology.
Abstract: It-s known that incorporating prior knowledge into support
vector regression (SVR) can help to improve the approximation
performance. Most of researches are concerned with the incorporation
of knowledge in the form of numerical relationships. Little work,
however, has been done to incorporate the prior knowledge on the
structural relationships among the variables (referred as to Structural
Prior Knowledge, SPK). This paper explores the incorporation of SPK
in SVR by constructing appropriate admissible support vector kernel
(SV kernel) based on the properties of reproducing kernel (R.K).
Three-levels specifications of SPK are studied with the corresponding
sub-levels of prior knowledge that can be considered for the method.
These include Hierarchical SPK (HSPK), Interactional SPK (ISPK)
consisting of independence, global and local interaction, Functional
SPK (FSPK) composed of exterior-FSPK and interior-FSPK. A
convenient tool for describing the SPK, namely Description Matrix
of SPK is introduced. Subsequently, a new SVR, namely Motivated
Support Vector Regression (MSVR) whose structure is motivated
in part by SPK, is proposed. Synthetic examples show that it is
possible to incorporate a wide variety of SPK and helpful to improve
the approximation performance in complex cases. The benefits of
MSVR are finally shown on a real-life military application, Air-toground
battle simulation, which shows great potential for MSVR to
the complex military applications.
Abstract: Many computational techniques were applied to
solution of heat conduction problem. Those techniques were the
finite difference (FD), finite element (FE) and recently meshless
methods. FE is commonly used in solution of equation of heat
conduction problem based on the summation of stiffness matrix of
elements and the solution of the final system of equations. Because
of summation process of finite element, convergence rate was
decreased. Hence in the present paper Cellular Automata (CA)
approach is presented for the solution of heat conduction problem.
Each cell considered as a fixed point in a regular grid lead to the
solution of a system of equations is substituted by discrete systems of
equations with small dimensions. Results show that CA can be used
for solution of heat conduction problem.
Abstract: Text-based game is supposed to be a low resource
consumption application that delivers good performances when
compared to graphical-intensive type of games. But, nowadays, some
of the online text-based games are not offering performances that are
acceptable to the users. Therefore, an online text-based game called
Star_Quest has been developed in order to analyze its behavior under
different performance measurements. Performance metrics such as
throughput, scalability, response time and page loading time are
captured to yield the performance of the game. The techniques in
performing the load testing are also disclosed to exhibit the viability
of our work. The comparative assessment between the results
obtained and the accepted level of performances are conducted as to
determine the performance level of the game. The study reveals that
the developed game managed to meet all the performance objectives
set forth.
Abstract: This paper suggests an improved integer frequency
offset (IFO) estimation scheme using P1 symbol for orthogonal
frequency division multiplexing (OFDM) based the second generation
terrestrial digital video broadcasting (DVB-T2) system. Proposed
IFO estimator is designed by a low-complexity blind IFO estimation
scheme, which is implemented with complex additions. Also, we
propose active carriers (ACs) selection scheme in order to prevent
performance degradation in blind IFO estimation. The simulation
results show that under the AWGN and TU6 channels, the proposed
method has low complexity than conventional method and almost
similar performance in comparison with the conventional method.