Abstract: A flaw or drift from expected operational performance in one component (NAND, PMIC, controller, DRAM, etc.) may affect the reliability of the entire Solid State Drive (SSD) system. Therefore, it is important to ensure the required quality of each individual component through qualification testing specified using standards or user requirements. Qualification testing is time-consuming and comes at a substantial cost for product manufacturers. A highly technical team, from all the eminent stakeholders is embarking on reliability prediction from beginning of new product development, identify critical to reliability parameters, perform full-blown characterization to embed margin into product reliability and establish control to ensure the product reliability is sustainable in the mass production. The paper will discuss a comprehensive development framework, comprehending SSD end to end from design to assembly, in-line inspection, in-line testing and will be able to predict and to validate the product reliability at the early stage of new product development. During the design stage, the SSD will go through intense reliability margin investigation with focus on assembly process attributes, process equipment control, in-process metrology and also comprehending forward looking product roadmap. Once these pillars are completed, the next step is to perform process characterization and build up reliability prediction modeling. Next, for the design validation process, the reliability prediction specifically solder joint simulator will be established. The SSD will be stratified into Non-Operating and Operating tests with focus on solder joint reliability and connectivity/component latent failures by prevention through design intervention and containment through Temperature Cycle Test (TCT). Some of the SSDs will be subjected to the physical solder joint analysis called Dye and Pry (DP) and Cross Section analysis. The result will be feedbacked to the simulation team for any corrective actions required to further improve the design. Once the SSD is validated and is proven working, it will be subjected to implementation of the monitor phase whereby Design for Assembly (DFA) rules will be updated. At this stage, the design change, process and equipment parameters are in control. Predictable product reliability at early product development will enable on-time sample qualification delivery to customer and will optimize product development validation, effective development resource and will avoid forced late investment to bandage the end-of-life product failures. Understanding the critical to reliability parameters earlier will allow focus on increasing the product margin that will increase customer confidence to product reliability.
Abstract: PERMATApintar® National Gifted Center is, to the author’s best of knowledge, the first center in Malaysia that provides a platform for Malaysian talented students with high ability in thinking. This center has built a teaching and learning biology curriculum that suits the ability of these gifted students. The level of PERMATApintar® biology curriculum is basically higher than the national biology curriculum. Here, the foundation students are exposed to the PERMATApintar® biology curriculum at the age of as early as 11 years old. This center practices a 4-time-a-year examination system to monitor the academic performances of the students. Generally, most of the time, male students show no or low interest towards biology subject compared to female students. This study is to investigate the association of students’ gender and their academic performances in biology examination. A total of 39 students’ scores in twelve sets of biology examinations in 3 years have been collected and analyzed by using the statistical analysis. Based on the analysis, there are no significant differences between male and female students against the biology academic performances with a significant level of p = 0.05. This indicates that gender is not associated with the scores of biology examinations among the students. Another result showed that the average score for male studenta was higher than the female students. Future research can be done by comparing the biology academic achievement in Malaysian National Examination (Sijil Pelajaran Malaysia, SPM) between the Foundation 3 students (Grade 9) and Level 2 students (Grade 11) with similar PERMATApintar® biology curriculum.
Abstract: The effect of needle diameter on the morphological structure of electrospun n-Bi2O3/epoxy-PVA nanofibers has been investigated using three different types of needle diameters. The results were observed and investigated using two techniques of scanning electron microscope (SEM). The first technique is backscattered SEM while the second is secondary electron SEM. The results demonstrate that there is a correlation between the needle diameter and the morphology of electrospun nanofibers. As the internal needle diameter decreases, the average nanofiber diameter decreases and the fibers get thinner and smoother without agglomeration or beads formation. Moreover, with small needle diameter the nanofibrous porosity get larger compared with large needle diameter.
Abstract: In construction, concrete is one of the materials that can commonly be used as for structural elements. Concrete consists of cement, sand, aggregate and water. Concrete can be added with admixture in the wet condition to suit the design purpose such as to prolong the setting time to improve workability. For strength improvement, concrete is being added with other hybrid materials to increase strength; this is because the tensile strength of concrete is very low in comparison to the compressive strength. This paper shows the usage of a waterproofing agent in concrete to enhance the tensile strength. High tensile concrete is expensive because the concrete mix needs fiber and also high cement content to be incorporated in the mix. High tensile concrete being used for structures that are being imposed by high impact dynamic load such as blast loading that hit the structure. High tensile concrete can be defined as a concrete mix design that achieved 30%-40% tensile strength compared to its compression strength. This research evaluates the usage of a waterproofing agent in a concrete mix as an element of reinforcement to enhance the tensile strength. According to the compression and tensile test, it shows that the concrete mix with a waterproofing agent enhanced the mechanical properties of the concrete. It is also show that the composite concrete with waterproofing is a high tensile concrete; this is because of the tensile is between 30% and 40% of the compression strength. This mix is economical because it can produce high tensile concrete with low cost.
Abstract: River is one of important water sources for many activities including industrial and domestic usage such as daily usage, transportation, power supply and recreational activities. However, increasing activities in a river has grown the sources of pollutant enters the water bodies, and degraded the water quality of the river. It becomes a challenge to develop an effective river management to ensure the water sources of the river are well managed and regulated. In Malaysia, several approaches for river management have been implemented such as Integrated River Basin Management (IRBM) program for coordinating the management of resources in a natural environment based on river basin to ensure their sustainability lead by Department of Drainage and Irrigation (DID), Malaysia. Nowadays, Total Maximum Daily Load (TMDL) is one of the best approaches for river management in Malaysia. TMDL implementation is regulated and implemented in the United States. A study on the development of TMDL in Malacca River has been carried out by doing water quality monitoring, the development of water quality model by using Environmental Fluid Dynamic Codes (EFDC), and TMDL implementation plan. The implementation of TMDL will help the stakeholders and regulators to control and improve the water quality of the river. It is one of the good approaches for river management in Malaysia.
Abstract: The problem of degradation of agricultural residues
from palm oil industry is increasing due to its expansion.
Lignocelloulosic waste from these industry represent large amount of
unutilized resources, this is due to their high lignin content. Since
white rot fungi are capable of degrading lignin, its potential for the
degradation of lignocelloulosic waste from palm oil industry was
accessed. The lignocellluloses content was measured before and after
biodegradation and the rate of reduction was determined. From the
results of the biodegradation, it was observed that hemicellulose
reduces by 22.62%, cellulose by 20.97% and lignin by 10.65% from
the initials lignocelluloses contents. Thus, to improve the digestibility
of palm oil mesocarp fibre, treatment by white rot-fungi is
recommended.
Abstract: Banana pseudo-stem and fruit-bunch-stem are
agricultural residues that can be used for conversion to bio-char, biooil,
and gases by using thermochemical process. The aim of this work
is to characterize banana pseudo-stem and banana fruit-bunch-stem
through proximate analysis, elemental analysis, chemical analysis,
thermo-gravimetric analysis, and heating calorific value. The ash
contents of the banana pseudo-stem and banana fruit-bunch-stem are
11.0 mf wt.% and 20.6 mf wt.%; while the carbon content of banana
pseudo-stem and fruit-bunch-stem are 37.9 mf wt.% and 35.58 mf
wt.% respectively. The molecular formulas for banana stem and
banana fruit-bunch-stem are C24H33NO26 and C19H29NO33
respectively. The measured higher heating values of banana pseudostem
and banana fruit-bunch-stem are 15.5MJ/kg and 12.7 MJ/kg
respectively. By chemical analysis, the lignin, cellulose, and
hemicellulose contents in the samples will also be presented. The
feasibility of the banana wastes to be a feedstock for thermochemical
process in comparison with other biomass will be discussed in this
paper.
Abstract: This study was conducted to generate empirical evidence on validity and reliability of the item of Competency Assessment Implementation (CAI) Instrument using Rasch Model for polythomous data aided by Winstep software version 3.68. The construct validity was examined by analyzing the point-measure correlation index (PTMEA), infit and outfit MNSQ values; meanwhile the reliability was examined by analyzing item reliability index. A survey technique was used as the major method with the CAI instrument on 156 teachers from vocational schools. The results have shown that the reliability of CAI Instrument items were between 0.80 and 0.98. PTMEA Correlation is in positive values, in which the item is able to distinguish between the ability of the respondent. Statistical data obtained show that out of 154 items, 12 items from the instrument suggested to be omitted. This study is hoped could bring a new direction to the process of data analysis in educational research.
Abstract: Rubric is a very important tool for teachers and students for a variety of purposes. Teachers use the rubric for evaluating student work while students use rubrics for self-assessment. Therefore, this paper was emphasized scoring rubric as a scoring tool for teachers in an environment of Competency Based Education and Training (CBET) in Malaysia Vocational College. A total of three teachers in the fields of electrical and electronics engineering were interviewed to identify how the use of rubrics practiced since vocational transformation implemented in 2012. Overall holistic rubric used to determine the performance of students in the skills area.
Abstract: Buzan mind mapping is an efficient system of note-taking that makes revision a fun thing to do for students. Tony Buzan has been teaching children all over the world for the past thirty years and has proved that mind maps are the magic formula in the classroom for everyone. The purpose of this paper is to discuss the importance of Buzan mind mapping as a note-taking technique for the secondary school students. This paper also examines the mind mapping technique, advantages and disadvantages of hand-drawn mind maps. Samples of students’ mind maps were presented and discussed.
Abstract: Grinding requires high specific energy and the consequent development of high temperature at tool-workpiece contact zone impairs workpiece quality by inducing thermal damage to the surface. Finishing grinding process requires component to be cut more than one pass. This paper deals with an investigation on the effect of multipass cutting on grinding performance in term of surface roughness and surface defect. An experimental set-up has been developed for this and a detailed comparison has been done with a single pass and various numbers of cutting pass. Results showed that surface roughness increase with the increase in a number of cutting pass. Good surface finish of 0.26μm was obtained for single pass cutting and 0.73μm for twenty pass cutting. It was also observed that the thickness of the white layer increased with the increased in a number of cutting pass.
Abstract: The potential of using herbal Betula alba (BA) and Convolvulus arvensis (CA) as a natural antioxidant for food applications were investigated. Each plant extract was prepared by using pure ethanol, different concentration of ethanol aqueous solutions, including 50% and 75%, 50% methanol aqueous and water. Total phenolic content (TPC) was determined using Folin–Ciocalteau method and antioxidant activity were analyzed by 2,2-diphenyl-1-picrylhydrazyl (DPPH) radicals, trolox equivalent antioxidant capacity (TEAC), Oxygen radical absorbance capacity (ORAC) and ferric reducing antioxidant power (FRAP) respectively. Ethanol extract of CA exhibited the highest TPC and antioxidant activity; however BA showed varies of antioxidant activity value in each assay. The BA and CA exhibit the potential sources of natural antioxidant for food commodities.
Abstract: The increase popularity of multimedia application especially in image processing places a great demand on efficient data storage and transmission techniques. Network communication such as wireless network can easily be intercepted and cause of confidential information leaked. Unfortunately, conventional compression and encryption methods are too slow; it is impossible to carry out real time secure image processing. In this research, Embedded Zerotree Wavelet (EZW) encoder which specially designs for wavelet compression is examined. With this algorithm, three methods are proposed to reduce the processing time, space and security protection that will be secured enough to protect the data.
Abstract: The purpose of this study is to determine in what
ways elementary education prospective teachers are being informed
about innovations and to explain the role of social influence in the
usage process of a technological innovation in terms of genders. The
study group consisted of 300 prospective teachers, including 234
females and 66 males. Data have been collected by a questionnaire
developed by the researchers. The result of the study showed that,
while prospective teachers are being informed about innovations
most frequently by mass media, they rarely seek to take expert
advice. In addition, analysis of results showed that the social
influence on females were significantly higher than males in usage
process of a technological innovation.
Abstract: Sensor Network are emerging as a new tool for
important application in diverse fields like military surveillance,
habitat monitoring, weather, home electrical appliances and others.
Technically, sensor network nodes are limited in respect to energy
supply, computational capacity and communication bandwidth. In
order to prolong the lifetime of the sensor nodes, designing efficient
routing protocol is very critical. In this paper, we illustrate the
existing routing protocol for wireless sensor network using data
centric approach and present performance analysis of these protocols.
The paper focuses in the performance analysis of specific protocol
namely Directed Diffusion and SPIN. This analysis reveals that the
energy usage is important features which need to be taken into
consideration while designing routing protocol for wireless sensor
network.
Abstract: Many attempts have been made to strengthen Feistel based block ciphers. Among the successful proposals is the key- dependent S-box which was implemented in some of the high-profile ciphers. In this paper a key-dependent permutation box is proposed and implemented on DES as a case study. The new modified DES, MDES, was tested against Diehard Tests, avalanche test, and performance test. The results showed that in general MDES is more resistible to attacks than DES with negligible overhead. Therefore, it is believed that the proposed key-dependent permutation should be considered as a valuable primitive that can help strengthen the security of Substitution-Permutation Network which is a core design in many Feistel based block ciphers.
Abstract: Salary risk and demographic risk have been identified
as main risks in analyzing pension expenditure particularly in
Defined Benefit pension plan. Therefore, public pension plan in
Malaysia is studied to analyze pension expenditure due to salary and
demographic risk. Through the literature review and interview session
with several officers in public sector, factors affecting pension
expenditure are determined. Then, the inter-relationships between
these factors are analyzed through causal loop diagram. The System
Dynamics model is later developed using iThink software to show how
demographic and salary changes affect the pension expenditure. Then, by
using actual data, the impact of different policy scenarios on pension
expenditure is analyzed. It is shown that dynamics simulation model of
pension expenditure is useful to evaluate the impact of changes and
policy decisions on risk particularly involving demographic and salary risk.
Abstract: Void formation in underfill is considered as failure
in flip chip manufacturing process. Void formation possibly caused
by several factors such as poor soldering and flux residue during
die attach process, void entrapment due moisture contamination,
dispense pattern process and setting up the curing process. This
paper presents the comparison of single step and two steps curing
profile towards the void and black dots formation in underfill for
Hi-CTE Flip Chip Ceramic Ball Grid Array Package (FC-CBGA).
Statistic analysis was conducted to analyze how different factors
such as wafer lot, sawing technique, underfill fillet height and
curing profile recipe were affected the formation of voids and
black dots. A C-Mode Scanning Aqoustic Microscopy (C-SAM)
was used to scan the total count of voids and black dots. It was
shown that the 2 steps curing profile provided solution for void
elimination and black dots in underfill after curing process.
Abstract: Malware is software which was invented and meant for doing harms on computers. Malware is becoming a significant threat in computer network nowadays. Malware attack is not just only involving financial lost but it can also cause fatal errors which may cost lives in some cases. As new Internet Protocol version 6 (IPv6) emerged, many people believe this protocol could solve most malware propagation issues due to its broader addressing scheme. As IPv6 is still new compares to native IPv4, some transition mechanisms have been introduced to promote smoother migration. Unfortunately, these transition mechanisms allow some malwares to propagate its attack from IPv4 to IPv6 network environment. In this paper, a proof of concept shall be presented in order to show that some existing IPv4 malware detection technique need to be improvised in order to detect malware attack in dual-stack network more efficiently. A testbed of dual-stack network environment has been deployed and some genuine malware have been released to observe their behaviors. The results between these different scenarios will be analyzed and discussed further in term of their behaviors and propagation methods. The results show that malware behave differently on IPv6 from the IPv4 network protocol on the dual-stack network environment. A new detection technique is called for in order to cater this problem in the near future.
Abstract: Possible advantages of technology in educational
context required the defining boundaries of formal and informal
learning. Increasing opportunity to ubiquitous learning by
technological support has revealed a question of how to discover
the potential of individuals in the spontaneous environments such as
social networks. This seems to be related with the question of what
purposes in social networks have been being used? Social networks
provide various advantages in educational context as collaboration,
knowledge sharing, common interests, active participation and
reflective thinking. As a consequence of these, the purpose of this
study is composed of proposing a new model that could determine
factors which effect adoption of social network applications for usage
in educational context. While developing a model proposal, the
existing adoption and diffusion models have been reviewed and they
are thought to be suitable on handling an original perspective instead
of using completely other diffusion or acceptance models because of
different natures of education from other organizations. In the
proposed model; social factors, perceived ease of use, perceived
usefulness and innovativeness are determined four direct constructs
that effect adoption process. Facilitating conditions, image,
subjective norms and community identity are incorporated to model
as antecedents of these direct four constructs.