Abstract: This paper investigates the application of large scale (LS-PV) two-axis tracking photovoltaic power plant in Al-Jagbob, Libya. A 50MW PV-grid connected (two-axis tracking) power plant design in Al-Jagbob, Libya has been carried out presently. A hetero-junction with intrinsic thin layer (HIT) type PV module has been selected and modeled. A Microsoft Excel-VBA program has been constructed to compute slope radiation, dew-point, sky temperature, and then cell temperature, maximum power output and module efficiency for this system, for tracking system. The results for energy production show that the total energy output is 128.5 GWh/year. The average module efficiency is 16.6%. The electricity generation capacity factor (CF) and solar capacity factor (SCF) were found to be 29.3% and 70.4% respectively. A 50MW two axis tracking power plant with a total energy output of 128.5 GWh/year would reduce CO2 pollution by 85,581 tonnes of each year. The payback time for the proposed LS-PV photovoltaic power plant was found to be 4 years.
Abstract: This paper proposes a new parameter identification
method based on Linear Fractional Transformation (LFT). It is
assumed that the target linear system includes unknown parameters.
The parameter deviations are separated from a nominal system via
LFT, and identified by organizing I/O signals around the separated
deviations of the real system. The purpose of this paper is to apply LFT
to simultaneously identify the parameter deviations in systems with
fewer outputs than unknown parameters. As a fundamental example,
this method is implemented to one degree of freedom vibratory system.
Via LFT, all physical parameters were simultaneously identified in this
system. Then, numerical simulations were conducted for this system to
verify the results. This study shows that all the physical parameters of a
system with fewer outputs than unknown parameters can be effectively
identified simultaneously using LFT.
Abstract: Power flow (PF) study, which is performed to
determine the power system static states (voltage magnitudes and
voltage angles) at each bus to find the steady state operating
condition of a system, is very important and is the most frequently
carried out study by power utilities for power system planning,
operation and control. In this paper, a counterpropagation neural
network (CPNN) is proposed to solve power flow problem under
different loading/contingency conditions for computing bus voltage
magnitudes and angles of the power system. The counterpropagation
network uses a different mapping strategy namely
counterpropagation and provides a practical approach for
implementing a pattern mapping task, since learning is fast in this
network. The composition of the input variables for the proposed
neural network has been selected to emulate the solution process of a
conventional power flow program. The effectiveness of the proposed
CPNN based approach for solving power flow is demonstrated by
computation of bus voltage magnitudes and voltage angles for
different loading conditions and single line-outage contingencies in
IEEE 14-bus system.
Abstract: Human activity is a major concern in a wide variety of
applications, such as video surveillance, human computer interface
and face image database management. Detecting and recognizing
faces is a crucial step in these applications. Furthermore, major
advancements and initiatives in security applications in the past years
have propelled face recognition technology into the spotlight. The
performance of existing face recognition systems declines significantly
if the resolution of the face image falls below a certain level.
This is especially critical in surveillance imagery where often, due to
many reasons, only low-resolution video of faces is available. If these
low-resolution images are passed to a face recognition system, the
performance is usually unacceptable. Hence, resolution plays a key
role in face recognition systems. In this paper we introduce a new
low resolution face recognition system based on mixture of expert
neural networks. In order to produce the low resolution input images
we down-sampled the 48 × 48 ORL images to 12 × 12 ones using
the nearest neighbor interpolation method and after that applying
the bicubic interpolation method yields enhanced images which is
given to the Principal Component Analysis feature extractor system.
Comparison with some of the most related methods indicates that
the proposed novel model yields excellent recognition rate in low
resolution face recognition that is the recognition rate of 100% for
the training set and 96.5% for the test set.
Abstract: In this paper, we propose a new model of English-
Vietnamese bilingual Information Retrieval system. Although there
are so many CLIR systems had been researched and built, the accuracy of searching results in different languages that the CLIR
system supports still need to improve, especially in finding bilingual documents. The problems identified in this paper are the limitation of
machine translation-s result and the extra large collections of document to be found. So we try to establish a different model to overcome these problems.
Abstract: In the urban traffic network, the intersections are the
“bottleneck point" of road network capacity. And the arterials are the
main body in road network and the key factor which guarantees the
normal operation of the city-s social and economic activities. The
rapid increase in vehicles leads to seriously traffic jam and cause the
increment of vehicles- delay. Most cities of our country are
traditional single control system, which cannot meet the need for the
city traffic any longer. In this paper, Synchro6.0 as a platform to
minimize the intersection delay, optimizesingle signal cycle and split
for Zhonghua Street in Handan City. Meanwhile, linear control
system uses to optimize the phase for the t arterial road in this
system. Comparing before and after use the control, capacities and
service levels of this road and the adjacent road have improved
significantly.
Abstract: Long Term Evolution (LTE) is a 4G wireless
broadband technology developed by the Third Generation
Partnership Project (3GPP) release 8, and it's represent the
competitiveness of Universal Mobile Telecommunications System
(UMTS) for the next 10 years and beyond. The concepts for LTE
systems have been introduced in 3GPP release 8, with objective of
high-data-rate, low-latency and packet-optimized radio access
technology. In this paper, performance of different TCP variants
during LTE network investigated. The performance of TCP over
LTE is affected mostly by the links of the wired network and total
bandwidth available at the serving base station. This paper describes
an NS-2 based simulation analysis of TCP-Vegas, TCP-Tahoe, TCPReno,
TCP-Newreno, TCP-SACK, and TCP-FACK, with full
modeling of all traffics of LTE system. The Evaluation of the
network performance with all TCP variants is mainly based on
throughput, average delay and lost packet. The analysis of TCP
performance over LTE ensures that all TCP's have a similar
throughput and the best performance return to TCP-Vegas than other
variants.
Abstract: The prediction of financial time series is a very
complicated process. If the efficient market hypothesis holds, then the predictability of most financial time series would be a rather
controversial issue, due to the fact that the current price contains already all available information in the market. This paper extends
the Adaptive Neuro Fuzzy Inference System for High Frequency
Trading which is an expert system that is capable of using fuzzy reasoning combined with the pattern recognition capability of neural networks to be used in financial forecasting and trading in high
frequency. However, in order to eliminate unnecessary input in the
training phase a new event based volatility model was proposed.
Taking volatility and the scaling laws of financial time series into consideration has brought about the development of the Intraday Seasonality Observation Model. This new model allows the observation of specific events and seasonalities in data and subsequently removes any unnecessary data. This new event based
volatility model provides the ANFIS system with more accurate input
and has increased the overall performance of the system.
Abstract: Herein, we report the different types of surface morphology due to the interaction between the pure protein Insulin (INS) and catanionic surfactant mixture of Sodium Dodecyl Sulfate (SDS) and Cetyl Trimethyl Ammonium Bromide (CTAB) at air/water interface obtained by the Langmuir-Blodgett (LB) technique. We characterized the aggregations by Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM) and Fourier transform infrared spectroscopy (FTIR) in LB films. We found that the INS adsorption increased in presence of catanionic surfactant at air/water interface. The presence of small amount of surfactant induces two-stage growth kinetics due to the pure protein absorption and protein-catanionic surface micelle interaction. The protein remains in native state in presence of small amount of surfactant mixture. Smaller amount of surfactant mixture with INS is producing surface micelle type structure. This may be considered for drug delivery system. On the other hand, INS becomes unfolded and fibrillated in presence of higher amount of surfactant mixture. In both the cases, the protein was successfully immobilized on a glass substrate by the LB technique. These results may find applications in the fundamental science of the physical chemistry of surfactant systems, as well as in the preparation of drug-delivery system.
Abstract: It is well known that a linear dynamic system including
a delay will exhibit limit cycle oscillations when a bang-bang sensor
is used in the feedback loop of a PID controller. A similar behaviour
occurs when a delayed feedback signal is used to train a neural
network. This paper develops a method of predicting this behaviour
by linearizing the system, which can be shown to behave in a manner
similar to an integral controller. Using this procedure, it is possible
to predict the characteristics of the neural network driven limit cycle
to varying degrees of accuracy, depending on the information known
about the system. An application is also presented: the intelligent
control of a spark ignition engine.
Abstract: This paper deals with the modeling and the evaluation of a multiplicative phase noise influence on the bit error ratio in a general space communication system. Our research is focused on systems with multi-state phase shift keying modulation techniques and it turns out, that the phase noise significantly affects the bit error rate, especially for higher signal to noise ratios. These results come from a system model created in Matlab environment and are shown in a form of constellation diagrams and bit error rate dependencies. The change of a user data bit rate is also considered and included into simulation results. Obtained outcomes confirm theoretical presumptions.
Abstract: This paper presents Genetic Algorithm (GA) based
approach for the allocation of FACTS (Flexible AC Transmission
System) devices for the improvement of Power transfer capacity in an
interconnected Power System. The GA based approach is applied on
IEEE 30 BUS System. The system is reactively loaded starting from
base to 200% of base load. FACTS devices are installed in the
different locations of the power system and system performance is
noticed with and without FACTS devices. First, the locations, where
the FACTS devices to be placed is determined by calculating active
and reactive power flows in the lines. Genetic Algorithm is then
applied to find the amount of magnitudes of the FACTS devices. This
approach of GA based placement of FACTS devices is tremendous
beneficial both in terms of performance and economy is clearly
observed from the result obtained.
Abstract: The paper investigates the potential of support vector
machines and Gaussian process based regression approaches to
model the oxygen–transfer capacity from experimental data of
multiple plunging jets oxygenation systems. The results suggest the
utility of both the modeling techniques in the prediction of the
overall volumetric oxygen transfer coefficient (KLa) from operational
parameters of multiple plunging jets oxygenation system. The
correlation coefficient root mean square error and coefficient of
determination values of 0.971, 0.002 and 0.945 respectively were
achieved by support vector machine in comparison to values of
0.960, 0.002 and 0.920 respectively achieved by Gaussian process
regression. Further, the performances of both these regression
approaches in predicting the overall volumetric oxygen transfer
coefficient was compared with the empirical relationship for multiple
plunging jets. A comparison of results suggests that support vector
machines approach works well in comparison to both empirical
relationship and Gaussian process approaches, and could successfully
be employed in modeling oxygen-transfer.
Abstract: The paper gives the pilot results of the project that is
oriented on the use of data mining techniques and knowledge
discoveries from production systems through them. They have been
used in the management of these systems. The simulation models of
manufacturing systems have been developed to obtain the necessary
data about production. The authors have developed the way of
storing data obtained from the simulation models in the data
warehouse. Data mining model has been created by using specific
methods and selected techniques for defined problems of production
system management. The new knowledge has been applied to
production management system. Gained knowledge has been tested
on simulation models of the production system. An important benefit
of the project has been proposal of the new methodology. This
methodology is focused on data mining from the databases that store
operational data about the production process.
Abstract: Nowadays there are several grid connected converter
in the grid system. These grid connected converters are generally the
converters of renewable energy sources, industrial four quadrant
drives and other converters with DC link. These converters are
connected to the grid through a three phase bridge. The standards
prescribe the maximal harmonic emission which could be easily
limited with high switching frequency. The increased switching
losses can be reduced to the half with the utilization of the wellknown
Flat-top modulation. The suggested control method is the
expansion of the Flat-top modulation with which the losses could be
also reduced to the half compared to the Flat-top modulation.
Comparing to traditional control these requirements can be
simultaneously satisfied much better with the DLF (DC Link
Floating) method.
Abstract: A hybrid Photovoltaic/Thermal (PV/T) solar system integrates photovoltaic and solar thermal technologies into one single solar energy device, with dual generation of electricity and heat energy. The aim of the present study is to evaluate the potential for introduction of the PV/T technology into Northern China. For this purpose, outdoor experiments were conducted on a prototype of a PV/T water-heating system. The annual thermal and electrical performances were investigated under the climatic conditions of Beijing. An economic analysis of the system was then carried out, followed by a sensitivity study. The analysis revealed that the hybrid system is not economically attractive with the current market and energy prices. However, considering the continuous commitment of the Chinese government towards policy development in the renewable energy sector, and technological improvements like the increasing cost-effectiveness of PV cells, PV/Thermal technology may become economically viable in the near future.
Abstract: Cenozoic basalts found in Jiangsu province of eastern
China include tholeiites and alkali basalts. The present paper analyzed
the major, trace elements, rare earth elements of these Cenozoic
basalts and combined with Sr-Nd isotopic compositions proposed by
Chen et al. (1990)[1] in the literatures to discuss the petrogenesis of
these basalts and the geochemical characteristics of the source mantle.
Based on major, trace elements and fractional crystallization model
established by Brooks and Nielsen (1982)[2] we suggest that the
basaltic magma has experienced olivine + clinopyroxene fractionation
during its evolution. The chemical compositions of basaltic rocks from
Jiangsu province indicate that these basalts may belong to the same
magmatic system. Spidergrams reveal that Cenozoic basalts from
Jiangsu province have geochemical characteristics similar to those of
ocean island basalts(OIB). The slight positive Nb and Ti anomalies
found in basaltic rocks of this study suggest the presence of Ti-bearing
minerals in the mantle source and these Ti-bearing minerals had
contributed to basaltic magma during partial melting, indicating a
metasomatic event might have occurred before the partial melting.
Based on the Sr vs. Nd isotopic ratio plots, we suggest that Jiangsu
basalts may be derived from partial melting of mantle source which
may represent two-end members mixing of DMM and EM-I. Some
Jiangsu basaltic magma may be derived from partial melting of EM-I
heated by the upwelling asthenospheric mantle or asthenospheric
diapirism.
Abstract: Magnesium is used implant material potentially for
non-toxicity to the human body. Due to the excellent
bio-compatibility, Mg alloys is applied to implants avoiding removal
second surgery. However, it is found commercial magnesium alloys
including aluminum has low corrosion resistance, resulting
subcutaneous gas bubbles and consequently the approach as
permanent bio-materials. Generally, Aluminum is known to pollution
substance, and it raises toxicity to nervous system. Therefore
especially Mg-35Zn-3Ca alloy is prepared for new biodegradable
materials in this study. And the pulsed power is used in
constant-current mode of DC power kinds of anodization. Based on
the aforementioned study, it examines corrosion resistance and
biocompatibility by effect of current and frequency variation. The
surface properties and thickness were compared using scanning
electronic microscopy. Corrosion resistance was assessed via
potentiodynamic polarization and the effect of oxide layer on the body
was assessed cell viability. Anodized Mg-35Zn-3Ca alloy has good
biocompatibility in vitro by current and frequency variation.
Abstract: Logistics outsourcing is a growing trend and measuring its performance, a challenge. It must be consistent with the objectives set for logistics outsourcing, but we have found no objective-based performance measurement system. We have conducted a comprehensive review of the specialist literature to cover this gap, which has led us to identify and define these objectives. The outcome is that we have obtained a list of the most relevant objectives and their descriptions. This will enable us to analyse in a future study whether the indicators used for measuring logistics outsourcing performance are consistent with the objectives pursued with the outsourcing. If this is not the case, a proposal will be made for a set of financial and operational indicators to measure performance in logistics outsourcing that take the goals being pursued into account.
Abstract: The paper presents a computational tool developed for
the evaluation of technical and economic advantages of an innovative
cleaning and conditioning technology of fluidized bed steam/oxygen
gasifiers outlet product gas. This technology integrates into a single
unit the steam gasification of biomass and the hot gas cleaning and
conditioning system. Both components of the computational tool,
process flowsheet and economic evaluator, have been developed
under IPSEpro software. The economic model provides information
that can help potential users, especially small and medium size
enterprises acting in the regenerable energy field, to decide the
optimal scale of a plant and to better understand both potentiality and
limits of the system when applied to a wide range of conditions.