Abstract: New advancement of technology and never satisfying demands of the civilization are putting huge pressure on the natural fuel resources and these resources are at a constant threat to its sustainability. To get the best out of the automobile, the optimum balance between performance and fuel economy is important. In the present state of art, either of the above two aspects are taken into mind while designing and development process which puts the other in the loss as increase in fuel economy leads to decrement in performance and vice-versa. In-depth observation of the vehicle dynamics apparently shows that large amount of energy is lost during braking and likewise large amount of fuel is consumed to reclaim the initial state, this leads to lower fuel efficiency to gain the same performance. Current use of Kinetic Energy Recovery System is only limited to sports vehicles only because of the higher cost of this system. They are also temporary in nature as power can be squeezed only during a small time duration and use of superior parts leads to high cost, which results on concentration on performance only and neglecting the fuel economy. In this paper Kinetic Energy Recovery System for storing the power and then using the same while accelerating has been discussed. The major storing element in this system is a Flat Spiral Spring that will store energy by compression and torsion.
The use of spring ensure the permanent storage of energy until used by the driver unlike present mechanical regeneration system in which the energy stored decreases with time and is eventually lost. A combination of internal gears and spur gears will be used in order to make the energy release uniform which will lead to safe usage. The system can be used to improve the fuel efficiency by assisting in overcoming the vehicle’s inertia after braking or to provide instant acceleration whenever required by the driver. The performance characteristics of the system including response time, mechanical efficiency and overall increase in efficiency are demonstrated. This technology makes the KERS (Kinetic Energy Recovery System) more flexible and economical allowing specific application while at the same time increasing the time frame and ease of usage.
Abstract: In the various working field, vibration may cause injurious to human body. Especially, in case of the vibration which is constantly and repeatedly transferred to the human. That gives serious physical problem, so called, Reynaud phenomenon. In this paper, we propose a vibration transmissibility reduction module with flexure mechanism for personal tools. At first, we select a target personal tool, grass cutter, and measure the level of vibration transmissibility on the hand. And then, we develop the concept design of the module that has stiffness for reduction the vibration transmissibility more than 20%, where the vibration transmissibility is measured with an accelerometer. In addition, the vibration reduction can be enhanced when the interior gap between inner and outer body is filled with silicone gel. This will be verified by the further experiment.
Abstract: Seasonal survey of freshwater snails in different water
courses in Egypt during two successive years included 13 snail
species. They represented by Biomphalaria alexandrina, Bulinus
truncatus, Physa acuta, Helisoma duryi, Lymnaea natalensis,
Planorbis pantries, Cleopatra bulimoides, Lanistes carinatus,
Bellamya unicolor, Melanoides tuberculata, Theodoxus niloticus,
Succinia cleopatra and Valvata nilotica. B. alexandrina was most
abundant during autumn and spring represented by 26and14
snails/site, respectively. B. truncatus was most abundant during
winter (7.7and3.6snails/site) of the two years, respectively. L.
natalensis was represented by 7snails/site in summer. The tolerance
of different snail species to the chemical elements was determined
seasonally and correlated to their abundance. In spring, autumn and
winter, B. alexandrina was significantly found to live under the
highest level of Pb, Cd,Cu, Na, K and Ca concentrations than the
other species (p
Abstract: These Nowadays the explosion of bombs or explosive
materials such as gas and oil near or inside the buildings cause some
losses in installations and building components. This has made the
engineers to make the buildings and their components resistance
against the effects of explosion. These activities lead to provide
regulations and different methods. The above regulations are mostly
focused on the explosion effects resulting from the vehicles around
the buildings. Therefore, the explosion resulting from the vehicles
outside the buildings will be studied in this research.
In the present study, the main goals are to investigate the
explosion load effects on the structures located on the piles with the
specific quantity of plasticity and observing the permissible response
of these structures. The concentrated mass system and the spring with
two degree of freedom will be used to study the structural system.
Abstract: A multi fingered dexterous anthropomorphic hand is
being developed by the authors. The focus of the hand is the
replacement of human operators in hazardous environments and also
in environments where zero tolerance is observed for the human
errors. The robotic hand will comprise of five fingers (four fingers
and one thumb) each having four degrees of freedom (DOF) which
can perform flexion, extension, abduction, adduction and also
circumduction. For the actuation purpose pneumatic muscles and
springs will be used. The paper exemplifies the mechanical design for
the robotic hand. It also describes different mechanical designs that
have been developed before date.
Abstract: Groundwater is one of the most important water resources in Fars province. Based on this study, 95 percent of the total annual water consumption in Fars is used for agriculture, whereas the percentages for domestic and industrial uses are 4 and 1 percent, respectively. Population growth, urban and industrial growth, and agricultural development in Fars have created a condition of water stress. In this province, farmers and other users are pumping groundwater faster than its natural replenishment rate, causing a continuous drop in groundwater tables and depletion of this resource. In this research variation of groundwater level , their effects and ways to help control groundwater levels in some plains of Fars were evaluated .Excessive exploitation of groundwater in Darab, Jahrom, Estahban, Arsanjan, Khir and Niriz plains of Fars caused the groundwater levels fall too fast or to unacceptable levels. The average drawdown of the water table in Arsanjan, Khir. Estahban and Niriz plain plains were 12,8, 9 and 6 meters during 16,11,11 and 13 years ago respectively. This not only reduces available water resources and well yields but also can saline water intrusion, reductions in river flow and in wetland areas , drying springs, and ground subsidence, considerable increase in pumping costs and a significant decline in crop yields as a result of the increasing salinity. Finally based on situation and condition of the aquifer some suggestions are recommended.
Abstract: Saturated two-phase fluid flows are often subject to
pressure induced oscillations. Due to compressibility the vapor
bubbles act as a spring with an asymmetric non-linear characteristic.
The volume of the vapor bubbles increases or decreases differently if
the pressure fluctuations are compressing or expanding;
consequently, compressing pressure fluctuations in a two-phase pipe
flow cause less displacement in the direction of the pipe flow than
expanding pressure fluctuations. The displacement depends on the
ratio of liquid to vapor, the ratio of pressure fluctuations over average
pressure and on the exciting frequency of the pressure fluctuations.
In addition, pressure fluctuations in saturated vapor bubbles cause
condensation and evaporation within the bubbles and change
periodically the ratio between liquid to vapor, and influence the
dynamical parameters for the oscillation. The oscillations are
conforming to an isenthalpic process at constant enthalpy with no
heat transfer and no exchange of work.
The paper describes the governing non-linear equation for twophase
fluid oscillations with condensation and evaporation, and
presents steady state approximate solutions for free and for pressure
induced oscillations. Resonance criteria and stability are discussed.
Abstract: The seismic rehabilitation designs of two reinforced
concrete school buildings, representative of a wide stock of similar
edifices designed under earlier editions of the Italian Technical
Standards, are presented in this paper. The mutual retrofit solution
elaborated for the two buildings consists in the incorporation of a
dissipative bracing system including pressurized fluid viscous springdampers
as passive protective devices. The mechanical parameters,
layouts and locations selected for the constituting elements of the
system; the architectural renovation projects developed to properly
incorporate the structural interventions and improve the appearance
of the buildings; highlights of the installation works already
completed in one of the two structures; and a synthesis of the
performance assessment analyses carried out in original and
rehabilitated conditions, are illustrated. The results of the analyses
show a remarkable enhancement of the seismic response capacities of
both structures. This allows reaching the high performance objectives
postulated in the retrofit designs with much lower costs and
architectural intrusion as compared to traditional rehabilitation
interventions designed for the same objectives.
Abstract: Atmospheric stability plays the most important role in
the transport and dispersion of air pollutants. Different methods are
used for stability determination with varying degrees of complexity.
Most of these methods are based on the relative magnitude of
convective and mechanical turbulence in atmospheric motions.
Richardson number, Monin-Obukhov length, Pasquill-Gifford
stability classification and Pasquill–Turner stability classification, are
the most common parameters and methods. The Pasquill–Turner
Method (PTM), which is employed in this study, makes use of
observations of wind speed, insolation and the time of day to classify
atmospheric stability with distinguishable indices. In this study, a
model is presented to determination of atmospheric stability
conditions using PTM. As a case study, meteorological data of
Mehrabad station in Tehran from 2000 to 2005 is applied to model.
Here, three different categories are considered to deduce the pattern
of stability conditions. First, the total pattern of stability classification
is obtained and results show that atmosphere is 38.77%, 27.26%,
33.97%, at stable, neutral and unstable condition, respectively. It is
also observed that days are mostly unstable (66.50%) while nights are
mostly stable (72.55%). Second, monthly and seasonal patterns are
derived and results indicate that relative frequency of stable
conditions decrease during January to June and increase during June
to December, while results for unstable conditions are exactly in
opposite manner. Autumn is the most stable season with relative
frequency of 50.69% for stable condition, whilst, it is 42.79%,
34.38% and 27.08% for winter, summer and spring, respectively.
Hourly stability pattern is the third category that points out that
unstable condition is dominant from approximately 03-15 GTM and
04-12 GTM for warm and cold seasons, respectively. Finally,
correlation between atmospheric stability and CO concentration is
achieved.
Abstract: In rail vehicles, air springs are very important isolating component, which guarantee good ride comfort for passengers during their trip. In the most new rail–vehicle models, developed by researchers, the thermo–dynamical effects of air springs are ignored and secondary suspension is modeled by simple springs and dampers. As the performance of suspension components have significant effects on rail–vehicle dynamics and ride comfort of passengers, a complete nonlinear thermo–dynamical air spring model, which is a combination of two different models, is introduced. Result from field test shows remarkable agreement between proposed model and experimental data. Effects of air suspension parameters on the system performances are investigated here and then these parameters are tuned to minimize Sperling ride comfort index during the trip. Results showed that by modification of air suspension parameters, passengers comfort is improved and ride comfort index is reduced about 10%.
Abstract: The introduction of sowing technologies into minimum- or no-tillage soil has a number of economical and environmental virtues, such as improving soil properties, decreasing soil erosion and degradation, and saving working time and fuel. However, the main disadvantage of these technologies is that plant residues on the soil surface reduce the quality of the planted crop seeds, thus requiring plant residues to be removed or cut. This paper presents a analysis of disc coulter parameters and an experimental investigation of cutting spring barley straw containing various amounts of moisture with different disc coulters (smooth and notched).
Abstract: This study has investigated a vehicle Lumped
Parameter Model (LPM) in frontal crash. There are several ways for
determining spring and damper characteristics and type of problem
shall be considered as system identification. This study use Genetic
Algorithm (GA) procedure, being an effective procedure in case of
optimization issues, for optimizing errors, between target data
(experimental data) and calculated results (being obtained by
analytical solving). In this study analyzed model in 5-DOF then
compared our results with 5-DOF serial model. Finally, the response
of model due to external excitement is investigated.
Abstract: The Kumamoto area, Kyushu, Japan has 1,041km2 in
area and about 1milion in population. This area is a greatest area in Japan which depends on groundwater for all of drinking water. Quantity of this local groundwater use is about 200MCM during the
year. It is understood that the main recharging area of groundwater exist in the rice field zone which have high infiltrate height ahead of
100mm/ day of the irrigated water located in the middle area of the Shira-River Basin. However, by decrease of the paddy-rice planting
area by urbanization and an acreage reduction policy, the groundwater income and expenditure turned worse. Then Kumamoto city and four
companies expended financial support to increase recharging water to
underground by ponded water in the field from 2004.
In this paper, the author reported the situation of recovery of groundwater by recharge and estimates the efficiency of recharge by
statistical method.
Abstract: The aim of this study is to point out whether personalization of mathematical word problems could affect student achievement or not. The research was applied on two-grades students at spring semester 2008-2009. Before the treatment, students personal data were taken and given to the computer. During the treatment, paper-based personalized problems and paper-based non personalized problems were prepared by computer as the same problems and then these problems were given to students. At the end of the treatment, students- opinion was taken. As a result of this research, it was found out that there were no significant differences between learners through personalized or non-personalized materials, and also there were no significant differences between gender through personalized and non-personalized problems. However, opinion of students was highly positive through the personalized problems.
Abstract: A motion protection system is designed for a parallel
motion platform with subsided cabin. Due to its complex structure,
parallel mechanism is easy to encounter interference problems
including link length limits, joints limits and self-collision. Thus a
virtual spring algorithm in operational space is developed for the
motion protection system to avoid potential damages caused by
interference. Simulation results show that the proposed motion
protection system can effectively eliminate interference problems and
ensure safety of the whole motion platform.
Abstract: Vehicle suspension design must fulfill
some conflicting criteria. Among those is ride comfort
which is attained by minimizing the acceleration
transmitted to the sprung mass, via suspension spring
and damper. Also good handling of a vehicle is a
desirable property which requires stiff suspension and
therefore is in contrast with a vehicle with good ride.
Among the other desirable features of a suspension is
the minimization of the maximum travel of suspension.
This travel which is called suspension working space in
vehicle dynamics literature is also a design constraint
and it favors good ride. In this research a full car 8
degrees of freedom model has been developed and the
three above mentioned criteria, namely: ride, handling
and working space has been adopted as objective
functions. The Multi Objective Programming (MOP)
discipline has been used to find the Pareto Front and
some reasoning used to chose a design point between
these non dominated points of Pareto Front.
Abstract: There are lots of different ways to find the natural
frequencies of a rotating system. One of the most effective methods
which is used because of its precision and correctness is the
application of the transfer matrix. By use of this method the entire
continuous system is subdivided and the corresponding differential
equation can be stated in matrix form. So to analyze shaft that is this
paper issue the rotor is divided as several elements along the shaft
which each one has its own mass and moment of inertia, which this
work would create possibility of defining the named matrix. By
Choosing more elements number, the size of matrix would become
larger and as a result more accurate answers would be earned. In this
paper the dynamics of a rotor-bearing system is analyzed,
considering the gyroscopic effect. To increase the accuracy of
modeling the thickness of the disk and bearings is also taken into
account which would cause more complicated matrix to be solved.
Entering these parameters to our modeling would change the results
completely that these differences are shown in the results. As said
upper, to define transfer matrix to reach the natural frequencies of
probed system, introducing some elements would be one of the
requirements. For the boundary condition of these elements, bearings
at the end of the shaft are modeled as equivalent spring and dampers
for the discretized system. Also, continuous model is used for the
shaft in the system. By above considerations and using transfer
matrix, exact results are taken from the calculations. Results Show
that, by increasing thickness of the bearing the amplitude of vibration
would decrease, but obviously the stiffness of the shaft and the
natural frequencies of the system would accompany growth.
Consequently it is easily understood that ignoring the influences of
bearing and disk thicknesses would results not real answers.
Abstract: Flow-shop scheduling problem (FSP) deals with the
scheduling of a set of jobs that visit a set of machines in the same
order. The FSP is NP-hard, which means that an efficient algorithm
for solving the problem to optimality is unavailable. To meet the
requirements on time and to minimize the make-span performance of
large permutation flow-shop scheduling problems in which there are
sequence dependent setup times on each machine, this paper
develops one hybrid genetic algorithms (HGA). Proposed HGA
apply a modified approach to generate population of initial
chromosomes and also use an improved heuristic called the iterated
swap procedure to improve initial solutions. Also the author uses
three genetic operators to make good new offspring. The results are
compared to some recently developed heuristics and computational
experimental results show that the proposed HGA performs very
competitively with respect to accuracy and efficiency of solution.
Abstract: Coriander is an annual and herbaceous plant, belong to
the apiaceae family. This plant is cultivated world widely. It is well
known for having medicinal properties. The aim of this experiment
was to study seed quality of species grown in Kermanshah
conditions. The experiment was carried out in research farm, Campus
of Agriculture and Natural Resources, Razi University, Kermanshah,
Iran. Coriander (local type) was grown in late spring May (5th and
20th) and Jun (4th and 19th), and plant density (10, 30, 50 and 70
plants m-2) in 2009. The experimental plots were laid out in a
factorial according to a randomized complete block design with three
replications. The fruits were harvest between 83.5 – 106.5 days after
sowing. The essential oil and oil content was extracted by Clevenger
and Soxhlet apparatuses, respectively. Results showed that delay at
planting date increased the oil content. Also, with the increase at
plant density was decreased oil content and essential oil.
Abstract: Various assisted reproductive techniques have been
developed and refined to obtain a large number of offspring from
genetically superior animals or obtain offspring from infertile (or
subfertile) animals. The embryo transfer is one assisted reproductive
technique developed well, aimed at increased productivity of selected
females, disease control, importation and exportation of livestock,
rapid screening of AI sires for genetically recessive characteristics,
treatment or circumvention of certain types of infertility. Embryo
transfer also is a useful research tool for evaluating fetal and maternal
interactions. This technique has been applied to nearly every species
of domestic animal and many species of wildlife and exotic animals,
including humans and non-human primates. The successful of
embryo transfers have been limited to within-animal, homologous
replacement of the embryos. There are several examples of
interspecific and intergeneric embryo transfers in which embryos
implanted but did not develop to term: sheep and goat, mouse and rat.
An immunological rejections and placental incompatibility between
the embryo and the surrogate mother appear to restrict interspecific
embryo transfer/interspecific pregnancy. Recently, preimplantation
embryo manipulation procedures have been applied, such as
technique of inner cell mass transfer. This technique will possible to
overcome the reproductive barrier interspecific embryo
transfer/interspecific pregnancy, if there is a protective mechanism
which prevents recognition of the foreign fetus by the mother of the
other species