Abstract: Thewake flow behind two yawed side-by-sidecircular
cylinders is investigated using athree-dimensional vorticity probe.
Four yaw angles (α), namely, 0°, 15°, 30° and 45° and twocylinder
spacing ratios T*
of 1.7 and 3.0 were tested. For T*
= 3.0, there exist
two vortex streets and the cylinders behave as independent and
isolated ones. The maximum contour value of the coherent streamwise
vorticity ~* ωx
is only about 10% of that of the spanwise vorticity ~* ωz
.
With the increase of α,
~* ωx
increases whereas ~* ωz
decreases. At α =
45°, ~* ωx
is about 67% of ~* ωz
.For T* = 1.7, only a single peak is
detected in the energy spectrum. The spanwise vorticity contours have
an organized pattern only at α = 0°. The maximum coherent vorticity
contours of ~* ω x
and ~* ωz
for T*
= 1.7 are about 30% and 7% of those
for T*
= 3.0.The independence principle (IP)in terms of Strouhal
numbers is applicable in both wakes when α< 40°.
Abstract: A design problem of non-uniform circular antenna arrays for maximum reduction of both the side lobe level (SLL) and first null beam width (FNBW) is dealt with. This problem is modeled as a simple optimization problem. The method of Firefly algorithm (FFA) is used to determine an optimal set of current excitation weights and antenna inter-element separations that provide radiation pattern with maximum SLL reduction and much improvement on FNBW as well. Circular array antenna laid on x-y plane is assumed. FFA is applied on circular arrays of 8-, 10-, and 12- elements. Various simulation results are presented and hence performances of side lobe and FNBW are analyzed. Experimental results show considerable reductions of both the SLL and FNBW with respect to those of the uniform case and some standard algorithms GA, PSO and SA applied to the same problem.
Abstract: This paper describes optimal thinning of an Elliptical
Cylindrical Array (ECA) of uniformly excited isotropic antennas
which can generate directive beam with minimum relative Side Lobe
Level (SLL). The Particle Swarm Optimization (PSO) method, which
represents a new approach for optimization problems in
electromagnetic, is used in the optimization process. The PSO is used
to determine the optimal set of ‘ON-OFF’ elements that provides a
radiation pattern with maximum SLL reduction. Optimization is done
without prefixing the value of First Null Beam Width (FNBW). The
variation of SLL with element spacing of thinned array is also
reported. Simulation results show that the number of array elements
can be reduced by more than 50% of the total number of elements in
the array with a simultaneous reduction in SLL to less than -27dB.
Abstract: Bone Anchored Hearing Implants (BAHI) are
routinely used in patients with conductive or mixed hearing loss, e.g.
if conventional air conduction hearing aids cannot be used. New
sound processors and new fitting software now allow the adjustment
of parameters such as loudness compression ratios or maximum
power output separately. Today it is unclear, how the choice of these
parameters influences aided speech understanding in BAHI users.
In this prospective experimental study, the effect of varying the
compression ratio and lowering the maximum power output in a
BAHI were investigated.
Twelve experienced adult subjects with a mixed hearing loss
participated in this study. Four different compression ratios (1.0; 1.3;
1.6; 2.0) were tested along with two different maximum power output
settings, resulting in a total of eight different programs. Each
participant tested each program during two weeks. A blinded Latin
square design was used to minimize bias.
For each of the eight programs, speech understanding in quiet and
in noise was assessed. For speech in quiet, the Freiburg number test
and the Freiburg monosyllabic word test at 50, 65, and 80 dB SPL
were used. For speech in noise, the Oldenburg sentence test was
administered.
Speech understanding in quiet and in noise was improved
significantly in the aided condition in any program, when compared
to the unaided condition. However, no significant differences were
found between any of the eight programs. In contrast, on a subjective
level there was a significant preference for medium compression
ratios of 1.3 to 1.6 and higher maximum power output.
Abstract: Fuel rod analysis program transient (FRAPTRAN)
code was used to study the fuel rod performance during a postulated
large break loss of coolant accident (LBLOCA) in Maanshan nuclear
power plant (NPP). Previous transient results from thermal hydraulic
code, TRACE, with the same LBLOCA scenario, were used as input
boundary conditions for FRAPTRAN. The simulation results showed
that the peak cladding temperatures and the fuel centerline
temperatures were all below the 10CFR50.46 LOCA criteria. In
addition, the maximum hoop stress was 18 MPa and the oxide
thickness was 0.003mm for the present simulation cases, which are all
within the safety operation ranges. The present study confirms that this
analysis method, the FRAPTRAN code combined with TRACE, is an
appropriate approach to predict the fuel integrity under LBLOCA with
operational ECCS.
Abstract: In this paper, we present an autonomous guidance service by combinating the position information
from NFC and the orientation information from 6 a 6 axis acceleration and
terrestrial magnetism sensor. We developed an algorithm to calculate the device orientation
based on the data from acceleration and terrestrial magnetism sensor.With this function,
a autonomous guidance service can be provided, according the visitors's position and orientation.
This service may be convient for old people or disables or children.
Abstract: Green mussels (Perna viridis) can effectively remove
nutrients from seawater through their filtration process. This study
aims to estimate “net” nutrient removal rate by green mussel through
calculation of nutrient uptake and release. Nutrients (carbon, nitrogen
and phosphorus) uptake was calculated based on the mussel filtration
rate. Nutrient release was evaluated from carbon, nitrogen and
phosphorus released as mussel faeces. By subtracting nutrient release
from nutrient uptake, net nutrient removal by green mussel can be
found as 3302, 380 and 124 mg/year/indv. Mass balance model was
employed to simulate nutrient removal in actual green mussel
farming conditions. Mussels farm area, seawater flow rate, and
amount of mussels were considered in the model. Results show that
although larger quantity of green mussel farms lead to higher nutrient
removal rate, the maximum green mussel cultivation should be taken
into consideration as nutrients released through mussel excretion can
strongly affect marine ecosystem.
Abstract: Although a lot of importance has been given to resistance analysis for various vessel types, explicit guidelines applied to multihull vessels have not been clearly defined. The purpose of this investigation is to highlight the importance of the vessel’s layout in terms of three axes, the transverse (separation), the longitudinal (stagger) and the vertical (draught) with respect to resistance analysis. When a vessel has the potential to experience less resistance at a particular range of speeds a vast selection of opportunities are made available for both the commercial and leisure market.
Abstract: The results of an experimental program conducted on seventeen simply supported concrete beams to study the effect of transverse reinforcement on the behavior of lap splice of steel reinforcement in tension zones in high strength concrete beams, are presented. The parameters included in the experimental program were the concrete compressive strength, the lap splice length, the amount of transverse reinforcement provided within the splice region, and the shape of transverse reinforcement around spliced bars. The experimental results showed that the displacement ductility increased and the mode of failure changed from splitting bond failure to flexural failure when the amount of transverse reinforcement in splice region increased, and the compressive strength increased up to 100 MPa. The presence of transverse reinforcement around spliced bars had pronounced effect on increasing the ultimate load, the ultimate deflection, and the displacement ductility. The prediction of maximum steel stresses for spliced bars using ACI 318-05 building code was compared with the experimental results. The comparison showed that the effect of transverse reinforcement around spliced bars has to be considered into the design equations for lap splice length in high strength concrete beams.
Abstract: This paper presents an improved ant colony optimization (IACO) for solving the reliability redundancy allocation problem (RAP) in order to maximize system reliability. To improve the performance of ACO algorithm, two additional techniques, i.e. neighborhood search, and re-initialization process are presented. To show its efficiency and effectiveness, the proposed IACO is applied to solve three RAPs. Additionally, the results of the proposed IACO are compared with those of the conventional heuristic approaches i.e. genetic algorithm (GA), particle swarm optimization (PSO) and ant colony optimization (ACO). The experimental results show that the proposed IACO approach is comparatively capable of obtaining higher quality solution and faster computational time.
Abstract: Drought is universally acknowledged as a phenomenon associated with scarcity of water. The Standardized Precipitation Index (SPI) expresses the actual rainfall as standardized departure from rainfall probability distribution function. In this study severity and spatial pattern of meteorological drought was analyzed in the Puruliya District, West Bengal, India using multi-temporal SPI. Daily gridded data for the period 1971-2005 from 4 rainfall stations surrounding the study area were collected from IMD, Pune, and used in the analysis. Geographic Information System (GIS) was used to generate drought severity maps for the different time scales and months of the year. Temporal SPI graphs show that the maximum SPI value (extreme drought) occurs in station 3 in the year 1993. Mild and moderate droughts occur in the central portion of the study area. Severe and extreme droughts were mostly found in the northeast, northwest and the southwest part of the region.
Abstract: Evaluating and measuring the performance parameters of wheels and tillage equipments under controlled conditions obligates the use of soil bin facility. In this research designing, constructing and evaluating a single-wheel tester has been studied inside a soil bin. The tested wheel was directly driven by the electric motor. Vertical load was applied by a power bolt on wheel. This tester can measure required draft force, the depth of tire sinkage, contact area between wheel and soil, and soil stress at different depths and in the both alongside and perpendicular to the direction of traversing. In order to evaluate the system preparation, traction force was measured by the connected S-shaped load cell as arms between the wheel-tester and carriage. Treatments of forward speed, slip, and vertical load at a constant pressure were investigated in a complete randomized block design. The results indicated that the traction force increased at constant wheel load. The results revealed that the maximum traction force was observed within the %15 of slip.
Abstract: Present paper deals with an evaluation of magnitude of changes in biomass and net primary productivity at ‘Gujar Tal’ sloppy lake margin at Jaunpur in tropical semi-arid region of eastern U.P. (India). The study site abandoned or neglected lands (50 ×125 m) was divided into two zones, i.e. upper zone (up-land) and lower zone (low-land). Maximum biomass in the upper zone of dominant weed Desmostachya bipinnata (L.) Stapf. was 207.47 g m-2 and ‘rest weeds’ was 457.45 g m-2 both in the month of September. In contrast, the peak biomass value in the lower zone of dominant weed Oryza rufipogon Griff. was 1571.44 g m-2 in October and ‘rest weeds’ 270.65 g m-2 in February. Among the two zones, the peak total community biomass was observed 1655.62 g m-2 (October) in the lower zone while its peak value for the upper zone 457.45 g m-2 (September) was comparatively low. Maximum percentage contribution of dominant weeds (D. bipinnata and O. rufipogon) in the respective upper and lower zones and ‘rest weeds’ in both the zones varied in different months in the total community biomass. The peak net primary productivity of dominant weed (D. bipinnata) was 2.09g m-2 day-1 (September) and ‘rest weeds’ was 2.37 g m-2 day-1 (August) in the upper zone, while the lower zone for O. rufipogon was 5.25 g m-2 day-1 (June) as this zone was inundated later and ‘rest weeds’ was 2.08 g m-2 day-1 (January, 2009). The annual net production of total community at site I was highest, 409.58 g m-2 yr-1 in the upper zone followed by 395.58 g m-2 per eight month in the lower zone as this zone was flooded with water during rainy season. The site significance of variations in biomass in relation to plant species was tested by analysis of variance. It was significant between months in all the two zones (p
Abstract: By hand pollination was conducted to evaluated different pollen sources and their affects on fruit set and quality of wax apple. The following parameters were recorded: fruit set, seed set, fruit characteristics. Results showed that fruit set percentage with seed were significantly high in ‘Long Red B’ when ‘Black’, ‘Thyto’ were used as pollen parents. Pollen of ‘Black’, ‘Thyto’ resulted in high fruit weight, fruit diameter, fruit length, bigger flesh thickness, better total soluble solids as compared with other pollens. The observation of pollen-growth in vitro revealed that pollen germination at 15% sucrose concentration are required for optimum pollen germination with the high pollen germination were found in ‘Black’, ‘Thyto’. From the result, we concluded that ‘Black’, ‘Thyto’ were proved to be good pollinizers in ‘Long Red B’. Therefore, artificial cross-pollination using ‘Black’, ‘Thyto’ as pollinizers were strongly recommended for ‘Long Red B’ cultivar in wax apple orchard.
Abstract: The present work deals with the optimal placement of piezoelectric actuators on a thin plate using Modified Control Matrix and Singular Value Decomposition (MCSVD) approach. The problem has been formulated using the finite element method using ten piezoelectric actuators on simply supported plate to suppress first six modes. The sizes of ten actuators are combined to outline one actuator by adding the ten columns of control matrix to form a column matrix. The singular value of column control matrix is considered as the fitness function and optimal positions of the actuators are obtained by maximizing it with GA. Vibration suppression has been studied for simply supported plate with piezoelectric patches in optimal positions using Linear Quadratic regulator) scheme. It is observed that MCSVD approach has given the position of patches adjacent to each-other, symmetric to the centre axis and given greater vibration suppression than other previously published results on SVD.
Abstract: Pervaporation has the potential to be an alternative to the other traditional separation processes such as distillation,
adsorption, reverse osmosis and extraction. This study investigates the separation of phenol from water using a polyurethane membrane by pervaporation by applying the modified Maxwell-Stephen model. The modified Maxwell-Stefan model takes into account the non-ideal multi-component solubility effect, nonideal diffusivity of all permeating components, concentration dependent density of the membrane and diffusion coupling to predict various fluxes. Four cases has been developed to investigate the process parameters effects on the flux and weight fraction of phenol in the permeate values namely feed concentration, membrane thickness, operating temperature and operating downstream pressure. The model could
describe semi-quantitatively the performance of the pervaporation membrane for the given system as a very good agreement between the observed and theoretical fluxes was observed.
Abstract: In the present study, effect of critical medium components (a total of fifteen components) on ethanol production from waste cashew apple juice (CAJ) using yeast Saccharomyces diasticus was studied. A statistical response surface methodology
(RSM) based Plackett-Burman Design (PBD) was used for the design of experiments. The design contains a total of 32 experimental trails. The effect of medium components on ethanol was studied at two different levels such as low concentration level (-) and high concentration levels (+). The dependent variables selected in this study were ethanol concentration (g/L) and cellmass concentration (g/L). Data obtained from RSM on ethanol production were subjected to analysis of variance (ANOVA). In general, initial substrate concentration significantly influenced the microbial growth and product formation. Of the medium components evaluated, CAJ concentration, yeast extract, (NH4)2SO4, and malt extract showed significant effect on ethanol fermentation. A second-order polynomial model was used to predict the experimental data and the model fitted the data with a high correlation coefficient (R2 > 0.98).
Maximum ethanol (15.3 g/L) and biomass (6.4 g/L) concentrations
were obtained at the optimum medium composition and at optimum
condition (temperature-30°C; initial pH-6.8) after 72 h fermentation
using S.diasticus.
Abstract: The effect of viscosity ratio (λ, defined as viscosity of surrounding medium/viscosity of fluid jet) on stability of axisymmetric (m=0) and asymmetric (m=1) modes of perturbation on a liquid-liquid jet in presence of radial electric field (E0 ), is studied using linear stability analysis. The viscosity ratio is shown to have a damping effect on both the modes of perturbation. However
the effect was found more pronounced for the m=1 mode as compared to m=1 mode. Investigating the effect of both E0 and λ
simultaneously, an operating diagram is generated, which clearly shows the regions of dominance of the two modes for a range of
electric field and viscosity ratio values.
Abstract: This paper deals with use of pond ash and RBI Grade 81 for improvement in CBR values of clayey soil and grade-III materials used for base course of flexible pavement. The pond ash is a thermal power plant waste and RBI Grade 81 is chemical soil stabilizer. The geotechnical properties like Maximum Dry Density (MDD), Optimum Moisture Content (OMC), Unconfined Compressive Strength (UCS), CBR value and Differential Free Swell (DFS) index of soil are tested in the laboratory for different mixes of soil, pond ash and RBI Grade 81 for different proportions. The mixes of grade-III material, pond ash and RBI Grade 81 tested for CBR test. From the study it is found that the geotechnical properties of clayey soil are improved significantly, if pond ash added with RBI Grade 81. The optimum mix recommended for subgrade is soil: pond ash: RBI Grade 81 in proportions of 76:20:4. The CBR value of grade-III base course treated with 20% pond ash and 4% RBI Grade 81 is increased by 125.93% as compared to untreated grade-III base course.
Abstract: International market expansion involves a strategic process of market entry decision through which a firm expands its operation from domestic to the international domain. Hence, entry timing choices require the needs to balance the early entry risks and the problems in losing opportunities as a result of late entry into a new market. Questionnaire surveys administered to 115 Malaysian construction firms operating in 51 countries worldwide have resulted in 39.1 percent response rate. Factor analysis was used to determine the most significant factors affecting entry timing choices of the firms to penetrate the international market. A logistic regression analysis used to examine the firms’ entry timing choices, indicates that the model has correctly classified 89.5 per cent of cases as late movers. The findings reveal that the most significant factor influencing the construction firms’ choices as late movers was the firm factor related to the firm’s international experience, resources, competencies and financing capacity. The study also offers valuable information to construction firms with intention to internationalize their businesses.