Abstract: Saturated two-phase fluid flows are often subject to
pressure induced oscillations. Due to compressibility the vapor
bubbles act as a spring with an asymmetric non-linear characteristic.
The volume of the vapor bubbles increases or decreases differently if
the pressure fluctuations are compressing or expanding;
consequently, compressing pressure fluctuations in a two-phase pipe
flow cause less displacement in the direction of the pipe flow than
expanding pressure fluctuations. The displacement depends on the
ratio of liquid to vapor, the ratio of pressure fluctuations over average
pressure and on the exciting frequency of the pressure fluctuations.
In addition, pressure fluctuations in saturated vapor bubbles cause
condensation and evaporation within the bubbles and change
periodically the ratio between liquid to vapor, and influence the
dynamical parameters for the oscillation. The oscillations are
conforming to an isenthalpic process at constant enthalpy with no
heat transfer and no exchange of work.
The paper describes the governing non-linear equation for twophase
fluid oscillations with condensation and evaporation, and
presents steady state approximate solutions for free and for pressure
induced oscillations. Resonance criteria and stability are discussed.
Abstract: Technology of thin film deposition is of interest in
many engineering fields, from electronic manufacturing to corrosion
protective coating. A typical deposition process, like that developed
at the University of Eindhoven, considers the deposition of a thin,
amorphous film of C:H or of Si:H on the substrate, using the
Expanding Thermal arc Plasma technique. In this paper a computing
procedure is proposed to simulate the flow field in a deposition
chamber similar to that at the University of Eindhoven and a
sensitivity analysis is carried out in terms of: precursor mass flow
rate, electrical power, supplied to the torch and fluid-dynamic
characteristics of the plasma jet, using different nozzles. To this
purpose a deposition chamber similar in shape, dimensions and
operating parameters to the above mentioned chamber is considered.
Furthermore, a method is proposed for a very preliminary evaluation
of the film thickness distribution on the substrate. The computing
procedure relies on two codes working in tandem; the output from
the first code is the input to the second one. The first code simulates
the flow field in the torch, where Argon is ionized according to the
Saha-s equation, and in the nozzle. The second code simulates the
flow field in the chamber. Due to high rarefaction level, this is a
(commercial) Direct Simulation Monte Carlo code. Gas is a mixture
of 21 chemical species and 24 chemical reactions from Argon plasma
and Acetylene are implemented in both codes. The effects of the
above mentioned operating parameters are evaluated and discussed
by 2-D maps and profiles of some important thermo-fluid-dynamic
parameters, as per Mach number, velocity and temperature. Intensity,
position and extension of the shock wave are evaluated and the
influence of the above mentioned test conditions on the film
thickness and uniformity of distribution are also evaluated.
Abstract: Roadways in Amman city face many problems consequent upon poor drainage systems. Evaluation tools are necessary to identify those roads needing improvement in their drainage system, and those needing regular maintenance. This work aims at evaluating drainage conditions in selected roadways in Amman city with the intent of identifying the problems encountered in their drainage systems. Three sites in the vicinity of Amman city have been selected and then inspected via several field visits to determine the state of their existing drainage systems and define the major problems encountered in these systems. The evaluation tool used in this study is based on visual inspection supported by photographs that depicted the defined problems. Following the field assessment, the drainage system in each road was rated as excellent, fair, good, or poor. The study reveals that more than 60% of the roadways in the selected sites were in poor drainage conditions, which lead to tremendous environmental problems. This assessment serves as a guide for local decision makers to help plan for the maintenance of Amman city roadways drainage systems, and propose ways of managing the associated problems.
Abstract: This paper proposes new enhancement models to the
methods of nonlinear anisotropic diffusion to greatly reduce speckle
and preserve image features in medical ultrasound images. By
incorporating local physical characteristics of the image, in this case
scatterer density, in addition to the gradient, into existing tensorbased
image diffusion methods, we were able to greatly improve the
performance of the existing filtering methods, namely edge
enhancing (EE) and coherence enhancing (CE) diffusion. The new
enhancement methods were tested using various ultrasound images,
including phantom and some clinical images, to determine the
amount of speckle reduction, edge, and coherence enhancements.
Scatterer density weighted nonlinear anisotropic diffusion
(SDWNAD) for ultrasound images consistently outperformed its
traditional tensor-based counterparts that use gradient only to weight
the diffusivity function. SDWNAD is shown to greatly reduce
speckle noise while preserving image features as edges, orientation
coherence, and scatterer density. SDWNAD superior performances
over nonlinear coherent diffusion (NCD), speckle reducing
anisotropic diffusion (SRAD), adaptive weighted median filter
(AWMF), wavelet shrinkage (WS), and wavelet shrinkage with
contrast enhancement (WSCE), make these methods ideal
preprocessing steps for automatic segmentation in ultrasound
imaging.
Abstract: Under the limitation of investment budget, a utility
company is required to maximize the utilization of their existing
assets during their life cycle satisfying both engineering and financial
requirements. However, utility does not have knowledge about the
status of each asset in the portfolio neither in terms of technical nor
financial values. This paper presents a knowledge based model for
the utility companies in order to make an optimal decision on power
transformer with their utilization. CommonKADS methodology, a
structured development for knowledge and expertise representation,
is utilized for designing and developing knowledge based model. A
case study of One MVA power transformer of Nepal Electricity
Authority is presented. The results show that the reusable knowledge
can be categorized, modeled and utilized within the utility company
using the proposed methodologies. Moreover, the results depict that
utility company can achieve both engineering and financial benefits
from its utilization.
Abstract: The Knowledge Management (KM) Criteria is an
essential foundation to evaluate KM outcomes. Different sets of
criteria were developed and tailored by many researchers to
determine the results of KM initiatives. However, literature review
has emphasized on incomplete set of criteria for evaluating KM
outcomes. Hence, this paper tried to address the problem of
determining the criteria for measuring knowledge management
outcomes among different types of Malaysian organizations.
Successively, this paper was assumed to develop widely accepted
criteria to measure success of knowledge management efforts for
Malaysian organizations. Our analysis approach was based on the
ANOVA procedure to compare a set of criteria among different types
of organizations. This set of criteria was exploited from literature
review. It is hoped that this study provides a better picture for
different types of Malaysian organizations to establish a
comprehensive set of criteria due to measure results of KM programs.
Abstract: Cloud computing is becoming more and more matured over the last few years and consequently the demands for better cloud services is increasing rapidly. One of the research topics to improve cloud services is the desktop computing in virtualized environment. This paper aims at the development of an adaptive virtual desktop service in cloud computing platform based on our previous research on the virtualization technology. We implement cloud virtual desktop and application software streaming technology that make it possible for providing Virtual Desktop as a Service (VDaaS). Given the development of remote desktop virtualization, it allows shifting the user’s desktop from the traditional PC environment to the cloud-enabled environment, which is stored on a remote virtual machine rather than locally. This proposed effort has the potential to positively provide an efficient, resilience and elastic environment for online cloud service. Users no longer need to burden the platform maintenances and drastically reduces the overall cost of hardware and software licenses. Moreover, this flexible remote desktop service represents the next significant step to the mobile workplace, and it lets users access their desktop environments from virtually anywhere.
Abstract: Thirty six samples from each (aerobic and anoxic)
activated sludge were collected from two wastewater treatment plants
with MBRs in Berlin, Germany. The samples were prepared for count
and definition of fungal isolates; these isolates were purified by
conventional techniques and identified by microscopic examination.
Sixty tow species belonging to 28 genera were isolated from
activated sludge samples under aerobic conditions (28 genera and 58
species) and anoxic conditions (26 genera and 52 species). The
obtained data show that, Aspergillus was found at 94.4% followed by
Penicillium 61.1 %, Fusarium (61.1 %), Trichoderma (44.4 %) and
Geotrichum candidum (41.6 %) species were the most prevalent in all
activated sludge samples. The study confirmed that fungi can thrive
in activated sludge and sporulation, but isolated in different numbers
depending on the effect of aeration system. Some fungal species in
our study are saprophytic, and other a pathogenic to plants and
animals.
Abstract: The aim of the present paper is to investigate the
interdependency among ego-identity status, autobiographical memory
and cultural life story schema. The study shows considerable
differences between autobiographical memory characteristics and
“family script", which is typical for participants (adolescents, M age
years = 17.84, SD = 1.18, N = 58), with different ego-identity
statuses. Participants with diffused ego-identity status recalled fewer
autobiographical memories. Additionally, this group of participants
recalled fewer events from their parents- life. Participants with
moratorium ego-identity status dated their first recollections to a later
age than others, and recalled fewer memories relating to their
childhood. Participants with achieved identity status recalled more
self-defining memories and events from their parents- life. They used
more functions from the autobiographical memory. There weren-t
any significant differences between the foreclosed identity status
group and the others. These findings support the idea of a
bidirectional relation between culture, memory and self.
Abstract: In this paper, the effect of modified clay on the
mechanical efficiency of epoxy resin is examined. Studies by X ray
diffraction and microscopic transient electron method show that
modified clay distribution in polymer area is intercalated kind.
Examination the results of mechanical tests shows that existence of
modified clay in epoxy area increases pressure yield strength, tension
module and nano composite fracture toughness in relate of pure
epoxy. By microscopic examinations it is recognized too that the
action of toughness growth of this kind of nano composite is due to
crack deflection, formation of new surfaces and fracture of clay piles.
Abstract: The soil ecology of the organic and mineral soil layers
of laurel-leaved and Cryptomeria japonica forest in the Kasuga-yama
Hill Primeval Forest (Nara, Japan) was assessed. The number of
bacteria obtained by the dilution plate count method was less than
0.05% of those counted by the direct microscopic count. We therefore
found that forest soil contains large numbers of non-culturable
bacteria compared with agricultural soils. The numbers of bacteria and
fungi obtained by both the dilution plate count and the direct
microscopic count were larger in the deeper horizons (F and H) of the
organic layer than in the mineral soil layer. This suggests that active
microbial metabolism takes place in the organic layer. The numbers of
bacteria and the length of fungal hyphae obtained by the direct count
method were greater in the H horizon than in the F horizon. The direct
microscopic count revealed numerous non-culturable bacteria and
fungi in the soil. The ratio of fungal to bacterial biomass was lower in
the laurel-leaved forest soil. The fungal biomass was therefore
relatively low in the laurel-leaved forest soil due to differences in
forest vegetation.
Abstract: The manufacturing transmission line tower parts has
being generated hazardous waste which is required proper disposal
of waste for protection of land pollution. Manufacturing Process in
the manufacturing of steel angle, plates, pipes, channels are passes
through conventional, semi automatic and CNC machines for
cutting, marking, punching, drilling, notching, bending operations.
All fabricated material Coated with thin layer of Zinc in Galvanizing
plant where molten zinc is used for coating. Prior to Galvanizing,
chemical like 33% concentrated HCl Acid, ammonium chloride and
d-oil being used for pretreatment of iron. The bath of water with
sodium dichromate is used for cooling and protection of the
galvanized steel. For the heating purpose the furnace oil burners are
used. These above process the Zinc dross, Zinc ash, ETP sludge and
waste pickled acid generated as hazardous waste. The RPG has
made captive secured land fill site, since 1997 since then it was
using for disposal of hazardous waste after completion of SLF
(Secured land fill) site. The RPG has raised height from ground
level then now it is being used for disposal of waste as he designed
the SLF after in creasing height of from GL it is functional without
leach ate or adverse impacts in the environment.
Abstract: This research is designed for helping a WAPbased mobile phone-s user in order to analyze of logistics in the traffic area by applying and designing the accessible processes from mobile user to server databases. The research-s design comprises Mysql 4.1.8-nt database system for being the server which there are three sub-databases, traffic light – times of intersections in periods of the day, distances on the road of area-blocks where are divided from the main sample-area and speeds of sample vehicles (motorcycle, personal car and truck) in periods of the day. For interconnections between the server and user, PHP is used to calculate distances and travelling times from the beginning point to destination, meanwhile XHTML applied for receiving, sending and displaying data from PHP to user-s mobile. In this research, the main sample-area is focused at the Huakwang-Ratchada-s area, Bangkok, Thailand where usually the congested point and 6.25 km2 surrounding area which are split into 25 blocks, 0.25 km2 for each. For simulating the results, the designed server-database and all communicating models of this research have been uploaded to www.utccengineering.com/m4tg and used the mobile phone which supports WAP 2.0 XHTML/HTML multimode browser for observing values and displayed pictures. According to simulated results, user can check the route-s pictures from the requiring point to destination along with analyzed consuming times when sample vehicles travel in various periods of the day.
Abstract: Functional imaging procedures for the non-invasive assessment of tissue microcirculation are highly requested, but require a mathematical approach describing the trans- and intercapillary passage of tracer particles. Up to now, two theoretical, for the moment different concepts have been established for tracer kinetic modeling of contrast agent transport in tissues: pharmacokinetic compartment models, which are usually written as coupled differential equations, and the indicator dilution theory, which can be generalized in accordance with the theory of lineartime- invariant (LTI) systems by using a convolution approach. Based on mathematical considerations, it can be shown that also in the case of an open two-compartment model well-known from functional imaging, the concentration-time course in tissue is given by a convolution, which allows a separation of the arterial input function from a system function being the impulse response function, summarizing the available information on tissue microcirculation. Due to this reason, it is possible to integrate the open two-compartment model into the system-theoretic concept of indicator dilution theory (IDT) and thus results known from IDT remain valid for the compartment approach. According to the long number of applications of compartmental analysis, even for a more general context similar solutions of the so-called forward problem can already be found in the extensively available appropriate literature of the seventies and early eighties. Nevertheless, to this day, within the field of biomedical imaging – not from the mathematical point of view – there seems to be a trench between both approaches, which the author would like to get over by exemplary analysis of the well-known model.
Abstract: We consider a typical problem in the assembly of
printed circuit boards (PCBs) in a two-machine flow shop system to
simultaneously minimize the weighted sum of weighted tardiness and
weighted flow time. The investigated problem is a group scheduling
problem in which PCBs are assembled in groups and the interest is to
find the best sequence of groups as well as the boards within each
group to minimize the objective function value. The type of setup
operation between any two board groups is characterized as carryover
sequence-dependent setup time, which exactly matches with the real
application of this problem. As a technical constraint, all of the
boards must be kitted before the assembly operation starts (kitting
operation) and by kitting staff. The main idea developed in this paper
is to completely eliminate the role of kitting staff by assigning the
task of kitting to the machine operator during the time he is idle
which is referred to as integration of internal (machine) and external
(kitting) setup times. Performing the kitting operation, which is a
preparation process of the next set of boards while the other boards
are currently being assembled, results in the boards to continuously
enter the system or have dynamic arrival times. Consequently, a
dynamic PCB assembly system is introduced for the first time in the
assembly of PCBs, which also has characteristics similar to that of
just-in-time manufacturing. The problem investigated is
computationally very complex, meaning that finding the optimal
solutions especially when the problem size gets larger is impossible.
Thus, a heuristic based on Genetic Algorithm (GA) is employed. An
example problem on the application of the GA developed is
demonstrated and also numerical results of applying the GA on
solving several instances are provided.
Abstract: Dexamethasone (Dex) is a synthetic glucocorticoid
that is used in therapy. However prolonged treatments with high
doses are often required. This causes side effects that interfere with
the activity of several endocrine systems, including the gonadotropic
axis.
The aim of our study is to determine the effect of Dex on testicular
function in prepubertal Wistar rats.
Newborn Wistar rats are submitted to intraperitoneal injection of
Dex (1μg of Dex dissolved in NaCl 0.9% / 5g bw) for 20 days and
then sacrificed at the age of 40days. A control group received NaCl
0.9%. The rat is weighed daily. The plasmatic levels of testosterone,
LH and FSH were measured by radioimmunoassay. A histomorphometric
study was performed on sections of testis.
Treated groups showed a significant decrease in body weight (p
Abstract: Hand gesture is one of the typical methods used in
sign language for non-verbal communication. It is most commonly
used by people who have hearing or speech problems to
communicate among themselves or with normal people. Various sign
language systems have been developed by manufacturers around the
globe but they are neither flexible nor cost-effective for the end
users. This paper presents a system prototype that is able to
automatically recognize sign language to help normal people to
communicate more effectively with the hearing or speech impaired
people. The Sign to Voice system prototype, S2V, was developed
using Feed Forward Neural Network for two-sequence signs
detection. Different sets of universal hand gestures were captured
from video camera and utilized to train the neural network for
classification purpose. The experimental results have shown that
neural network has achieved satisfactory result for sign-to-voice
translation.
Abstract: In the present study, development of salbutamol
sulphate nanoparticles that adhere to gastric mucus was investigated.
Salbutamol sulphate has low bioavailability due to short transit time in
gastric. It also has a positive surface charge that provides hurdles to be
encapsulated by the positively strong mucoadhesive polymer of
chitosan. To overcome the difficulties, the surface charge of active
ingredient was modified using several nonionic and anionic
stomach-specific polymers. The nanoparticles were prepared using
ionotropic gelation technique. The evaluation involved determination
of particle size, zeta potential, entrapment efficiency, in vitro drug
release and in vitro mucoadhesion test. Results exhibited that the use
of anionic alginate polymer was more satisfactory than that of
nonionic polymer. Characteristics of the particles was nano-size, high
encapsulation efficiency, fulfilled the drug release requirements and
adhesive towards stomach for around 11 hours. This result shows that
the salbutamol sulphate nanoparticles can be utilized for improvement
its delivery.
Abstract: The use of renewable energy sources incl. biogas has become topical in accordance with the increasing demand for energy, decrease of fossil energy resources and the efforts to reduce greenhouse gas emissions as well as to increase energy independence from the territories where fossil energy resources are available.
As the technologies of biogas production from agricultural biomass develop, risk assessment and risk management become necessary for farms producing such a renewable energy. The need for risk assessments has become particularly topical when discussions on changing the biogas policy in the EU take place, which may influence the development of the sector in the future, as well as the operation of existing biogas facilities and their income level.
The current article describes results of the risk assessment for farms producing biomass from agriculture biomass in Latvia, the risk assessment system included 24 risks, that affect the whole biogas production process and the obtained results showed the high significance of political and production risks.
Abstract: In elevating performance in competetive sports, an
athlete must continously train in achieving maximum
performance,but needs to pay attention to recovery therapy, that is to
recover from fatigue as well as injury.The correct recovery therapy
will assist in process of recovery and helps in the training in
achieving better performace. Binahong (Anredera cordifolia) was
proven empirically by the locals in assisting speedy recovery from an
injury.Clinical research with lab animals receiving blunt trauma
injury, microscopically shown signs of: 1) redness, 2) heatiness, 3)
swelling and, 4) lack of activity. There is also microscopic indication
of: 1) infiltration of inflame cells (migration of cells to the trauma
area), 2) Cells necrosis, 3) Congestion (as a result of dead red blood
cells), 4) uedema. On administration of Binahong for 3 days, there is
a significant drop of 5% in cell inflammation, 2% increase of
fibroblast (cell membrance) count.Conclutin: Binahong do assist in
reducing cell inflammation and increase counts of cells fibroblast.
Suggestion: In helping athlete's to recover from force injury, we need
study about Binahong's roots to inflammation cell and healing of
injuried cell.