Abstract: An enhanced particle swarm optimization algorithm
(PSO) is presented in this work to solve the non-convex OPF
problem that has both discrete and continuous optimization variables.
The objective functions considered are the conventional quadratic
function and the augmented quadratic function. The latter model
presents non-differentiable and non-convex regions that challenge
most gradient-based optimization algorithms. The optimization
variables to be optimized are the generator real power outputs and
voltage magnitudes, discrete transformer tap settings, and discrete
reactive power injections due to capacitor banks. The set of equality
constraints taken into account are the power flow equations while the
inequality ones are the limits of the real and reactive power of the
generators, voltage magnitude at each bus, transformer tap settings,
and capacitor banks reactive power injections. The proposed
algorithm combines PSO with Newton-Raphson algorithm to
minimize the fuel cost function. The IEEE 30-bus system with six
generating units is used to test the proposed algorithm. Several cases
were investigated to test and validate the consistency of detecting
optimal or near optimal solution for each objective. Results are
compared to solutions obtained using sequential quadratic
programming and Genetic Algorithms.
Abstract: Development of artificial neural network (ANN) for
prediction of aluminum workpieces' surface roughness in ultrasonicvibration
assisted turning (UAT) has been the subject of the present
study. Tool wear as the main cause of surface roughness was also
investigated. ANN was trained through experimental data obtained
on the basis of full factorial design of experiments. Various
influential machining parameters were taken into consideration. It
was illustrated that a multilayer perceptron neural network could
efficiently model the surface roughness as the response of the
network, with an error less than ten percent. The performance of the
trained network was verified by further experiments. The results of
UAT were compared with the results of conventional turning
experiments carried out with similar machining parameters except for
the vibration amplitude whence considerable reduction was observed
in the built-up edge and the surface roughness.
Abstract: Current systems for face recognition techniques often
use either SVM or Adaboost techniques for face detection part and use
PCA for face recognition part. In this paper, we offer a novel method
for not only a powerful face detection system based on
Six-segment-filters (SSR) and Adaboost learning algorithms but also
for a face recognition system. A new exclusive face detection
algorithm has been developed and connected with the recognition
algorithm. As a result of it, we obtained an overall high-system
performance compared with current systems. The proposed algorithm
was tested on CMU, FERET, UNIBE, MIT face databases and
significant performance has obtained.
Abstract: A reduced-bit multiplication algorithm based on the ancient Vedic multiplication formulae is proposed in this paper. Both the Vedic multiplication formulae, Urdhva tiryakbhyam and Nikhilam, are first discussed in detail. Urdhva tiryakbhyam, being a general multiplication formula, is equally applicable to all cases of multiplication. It is applied to the digital arithmetic and is shown to yield a multiplier architecture which is very similar to the popular array multiplier. Due to its structure, it leads to a high carry propagation delay in case of multiplication of large numbers. Nikhilam Sutra, on the other hand, is more efficient in the multiplication of large numbers as it reduces the multiplication of two large numbers to that of two smaller numbers. The framework of the proposed algorithm is taken from this Sutra and is further optimized by use of some general arithmetic operations such as expansion and bit-shifting to take advantage of bit-reduction in multiplication. We illustrate the proposed algorithm by reducing a general 4x4-bit multiplication to a single 2 x 2-bit multiplication operation.
Abstract: In this paper, a method for deriving a group priority vector in the Fuzzy Analytic Network Process (FANP) is proposed. By introducing importance weights of multiple decision makers (DMs) based on their experiences, the Fuzzy Preferences Programming Method (FPP) is extended to a fuzzy group prioritization problem in the FANP. Additionally, fuzzy pair-wise comparison judgments are presented rather than exact numerical assessments in order to model the uncertainty and imprecision in the DMs- judgments and then transform the fuzzy group prioritization problem into a fuzzy non-linear programming optimization problem which maximize the group satisfaction. Unlike the known fuzzy prioritization techniques, the new method proposed in this paper can easily derive crisp weights from incomplete and inconsistency fuzzy set of comparison judgments and does not require additional aggregation producers. Detailed numerical examples are used to illustrate the implement of our approach and compare with the latest fuzzy prioritization method.
Abstract: There is increasing pressure on, and decline of
mopane woodlands due to increasing use and competition for
mopane resources in Zimbabwe in Namibia. Community management strategies, based largely on local knowledge are
evidently unable to cope. Research has generated potentially useful
information for mopane woodland management, but this information
has not been utilized. The work reported in this paper sought to add value to research work conducted on mopane woodlands by
developing effective community-based mopane woodland
management regimes that were based on both local and scientific
knowledge in Zimbabwe and Namibia. The conditions under which research findings were likely to be adopted for mopane woodland management by communities were investigated. The study was conducted at two sites each in Matobo and Omusati Districts in Zimbabwe and Namibia respectively. The mopane woodland
resources in the two study areas were assessed using scientific
ecological methods. A range of participatory methods was used to collect information on use of mopane woodland resources by communities, institutional arrangements governing access to and use
of these resources and to evaluate scientific knowledge for
applicability in local management regimes. Coppicing, thinning and
pollarding were the research generated management methods evaluated. Realities such as availability of woodland resources and
social roles and responsibilities influenced preferences for woodland
management interventions
Abstract: There are very complex communication systems, as
the multifunction radar, MFAR (Multi-Function Array Radar), where
functions are integrated all together, and simultaneously are
performed the classic functions of tracking and surveillance, as all
the functions related to the communication, countermeasures, and
calibration. All these functions are divided into the tasks to execute.
The task scheduler is a key element of the radar, since it does the
planning and distribution of energy and time resources to be shared
and used by all tasks. This paper presents schedulers based on the use
of multiple queue. Several schedulers have been designed and
studied, and it has been made a comparative analysis of different
performed schedulers. The tests and experiments have been done by
means of system software simulation. Finally a suitable set of radar
characteristics has been selected to evaluate the behavior of the task
scheduler working.
Abstract: This work presents a novel means of extracting fixedlength parameters from voice signals, such that words can be recognized
in linear time. The power and the zero crossing rate are first
calculated segment by segment from a voice signal; by doing so, two
feature sequences are generated. We then construct an FIR system
across these two sequences. The parameters of this FIR system, used
as the input of a multilayer proceptron recognizer, can be derived by
recursive LSE (least-square estimation), implying that the complexity of overall process is linear to the signal size. In the second part of
this work, we introduce a weighting factor λ to emphasize recent
input; therefore, we can further recognize continuous speech signals.
Experiments employ the voice signals of numbers, from zero to nine, spoken in Mandarin Chinese. The proposed method is verified to
recognize voice signals efficiently and accurately.
Abstract: The main problem is that there is a very low innovation performance in Latvia. Since Latvia is a Member State of European Union, it also shall have to fulfill the set targets and to improve innovative results.Universities are one of the main performers to provide innovative capacity of country. University, industry and government need to cooperate for getting best results.The intellectual property is one of the indicators to determine innovation level in the country or organization, and patents are one of the characteristics of intellectual property.The objective of the article is to determine indicators characterizing innovative environment in Latvia and influence of the development of universities on them.The methods that will be used in the article to achieve the objectives are quantitative and qualitative analysis of the literature, statistical data analysis and graphical analysis methods.
Abstract: The objective of this paper is to study the analysis and testing for determining the torsional stiffness of the student formula-s space frame. From past study, the space frame for Chulalongkorn University Student Formula team used in 2011 TSAE Auto Challenge Student Formula in Thailand was designed by considering required mass and torsional stiffness based on the numerical method and experimental method. The numerical result was compared with the experimental results to verify the torsional stiffness of the space frame. It can be seen from the large error of torsional stiffness of 2011 frame that the experimental result can not verify by the numerical analysis due to the different between the numerical model and experimental setting. In this paper, the numerical analysis and experiment of the same 2011 frame model is performed by improving the model setting. The improvement of both numerical analysis and experiment are discussed to confirm that the models from both methods are same. After the frame was analyzed and tested, the results are compared to verify the torsional stiffness of the frame. It can be concluded that the improved analysis and experiments can used to verify the torsional stiffness of the space frame.
Abstract: Since the actuator capacity is limited, in the real
application of active control systems under sever earthquakes it is
conceivable that the actuators saturate, hence the actuator saturation
should be considered as a constraint in design of optimal controllers.
In this paper optimal design of active controllers for nonlinear
structures by considering actuator saturation, has been studied. The
proposed method for designing optimal controllers is based on
defining an optimization problem which the objective has been to
minimize the maximum displacement of structure when a limited
capacity for actuator has been used. To this end a single degree of
freedom (SDF) structure with a bilinear hysteretic behavior has been
simulated under a white noise ground acceleration of different
amplitudes. Active tendon control mechanism, comprised of prestressed
tendons and an actuator, and extended nonlinear Newmark
method based instantaneous optimal control algorithm have been
used. To achieve the best results, the weights corresponding to
displacement, velocity, acceleration and control force in the
performance index have been optimized by the Distributed Genetic
Algorithm (DGA). Results show the effectiveness of the proposed
method in considering actuator saturation. Also based on the
numerical simulations it can be concluded that the actuator capacity
and the average value of required control force are two important
factors in designing nonlinear controllers which consider the actuator
saturation.
Abstract: This paper describes various stages of design and prototyping of a modular robot for use in various industrial applications. The major goal of current research has been to design and make different robotic joints at low cost capable of being assembled together in any given order for achieving various robot configurations. Five different types of joins were designed and manufactured where extensive research has been carried out on the design of each joint in order to achieve optimal strength, size, modularity, and price. This paper presents various stages of research and development undertaken to engineer these joints that include material selection, manufacturing, and strength analysis. The outcome of this research addresses the birth of a new generation of modular industrial robots with a wider range of applications and greater efficiency.
Abstract: Variable speed drives are growing and varying. Drives expanse depend on progress in different part of science like power system, microelectronic, control methods, and so on. Artificial intelligent contains hard computation and soft computation. Artificial intelligent has found high application in most nonlinear systems same as motors drive. Because it has intelligence like human but there are no sentimental against human like angriness and.... Artificial intelligent is used for various points like approximation, control, and monitoring. Because artificial intelligent techniques can use as controller for any system without requirement to system mathematical model, it has been used in electrical drive control. With this manner, efficiency and reliability of drives increase and volume, weight and cost of them decrease.
Abstract: Today, numerical simulation is a powerful tool to
solve various hydraulic engineering problems. The aim of this
research is numerical solutions of shallow water equations using
finite volume method for Simulations of dam break over wet and dry
bed. In order to solve Riemann problem, Roe-s approximate solver is
used. To evaluate numerical model, simulation was done in 1D and
2D states. In 1D state, two dam break test over dry bed (with and
without friction) were studied. The results showed that Structural
failure around the dam and damage to the downstream constructions
in bed without friction is more than friction bed. In 2D state, two
tests for wet and dry beds were done. Generally in wet bed case,
waves are propagated to canal sides but in dry bed it is not
significant. Therefore, damage to the storage facilities and
agricultural lands in wet bed case is more than in dry bed.
Abstract: In this study a neural network (NN) was proposed to
predict the sorption of binary mixture of copper-cobalt ions into
clinoptilolite as ion-exchanger. The configuration of the
backpropagation neural network giving the smallest mean square
error was three-layer NN with tangent sigmoid transfer function at
hidden layer with 10 neurons, linear transfer function at output layer
and Levenberg-Marquardt backpropagation training algorithm.
Experiments have been carried out in the batch reactor to obtain
equilibrium data of the individual sorption and the mixture of coppercobalt
ions. The obtained modeling results have shown that the used
of neural network has better adjusted the equilibrium data of the
binary system when compared with the conventional sorption
isotherm models.
Abstract: These This paper looks into frameworks which aim at
furthering the discussion of the role of regenerative design practices
in a city-s historic core and the tool of urban design to achieve urban
revitalization on the island of Cyprus. It also examines the region-s
demographic mix, the effectiveness of its governmental coordination
and the strategies of adaptive reuse and strategic investments in older
areas with existing infrastructure. The two main prongs of
investigation will consider the effect of the existing and proposed
changes in the physical infrastructure and fabric of the city, as well as
the catalytic effect of sustainable urban design practices. Through this
process, the work hopes to integrate the contained potential within
the existing historic core and the contributions and participation of
the migrant and immigrant populations to the local economy. It also
examines ways in which this coupling of factors can bring to the front
the positive effects of this combined effort on an otherwise sluggish
local redevelopment effort. The data for this study is being collected
and organized as part of ongoing urban design and development
student workshop efforts in urban planning and design education.
The work is presented in graphic form and includes data collected
from interviews with study area organizations and the community at
large. Planning work is also based on best practices initiated by the
staff of the Nicosia Master Plan task force, which coordinates holistic
planning efforts for the historic center of the city of Nicosia.
Abstract: As current business environment is demanding a
constant adaptation of companies, the planning and strategic
management should be an ongoing and natural process in all kind of
organizations. The use of management and monitoring strategic
performance tools such as the Balanced Scorecard (BSC) have been
popular; even to Small and Medium-sized Enterprises. This paper
aims to investigate whether the BSC is being used in monitoring the
performance of small businesses, particularly in small fuel retailers
companies, which are competing in co-branding; and if not, it aims to
identify its strategic orientation in order to recommend a possible
strategy map for those managers that are willing to adopt this model
as an alternative to traditional ones for organizational performance
evaluation, which often focus only on evaluation of the
organizational financial performance.
Abstract: In this paper we propose a method for vision systems
to consistently represent functional dependencies between different
visual routines along with relational short- and long-term knowledge
about the world. Here the visual routines are bound to visual properties
of objects stored in the memory of the system. Furthermore,
the functional dependencies between the visual routines are seen
as a graph also belonging to the object-s structure. This graph is
parsed in the course of acquiring a visual property of an object to
automatically resolve the dependencies of the bound visual routines.
Using this representation, the system is able to dynamically rearrange
the processing order while keeping its functionality. Additionally, the
system is able to estimate the overall computational costs of a certain
action. We will also show that the system can efficiently use that
structure to incorporate already acquired knowledge and thus reduce
the computational demand.
Abstract: Breastfeeding is an important concept in the maternal life of a woman. In this paper, we focus on exclusive breastfeeding. Exclusive breastfeeding is the feeding of a baby on no other milk apart from breast milk. This type of breastfeeding is very important during the first six months because it supports optimal growth and development during infancy and reduces the risk of obliterating diseases and problems. Moreover, in Mauritius, exclusive breastfeeding has decreased the incidence and/or severity of diarrhea, lower respiratory infection and urinary tract infection. In this paper, we give an overview of exclusive breastfeeding in Mauritius and the factors influencing it. We further analyze the local practices of exclusive breastfeeding using the Generalized Poisson regression model and the negative-binomial model since the data are over-dispersed.
Abstract: Brain ArterioVenous Malformation (BAVM) is an abnormal tangle of brain blood vessels where arteries shunt directly into veins with no intervening capillary bed which causes high pressure and hemorrhage risk. The success of treatment by embolization in interventional neuroradiology is highly dependent on the accuracy of the vessels visualization. In this paper the performance of clustering techniques on vessel segmentation from 3- D rotational angiography (3DRA) images is investigated and a new technique of segmentation is proposed. This method consists in: preprocessing step of image enhancement, then K-Means (KM), Fuzzy C-Means (FCM) and Expectation Maximization (EM) clustering are used to separate vessel pixels from background and artery pixels from vein pixels when possible. A post processing step of removing false-alarm components is applied before constructing a three-dimensional volume of the vessels. The proposed method was tested on six datasets along with a medical assessment of an expert. Obtained results showed encouraging segmentations.