Abstract: This paper presents the study of strengthening R/C
beams with large circular and square opening located at flexure zone
by Carbon Fiber Reinforced Polymer (CFRP) laminates. A total of
five beams were tested to failure under four point loading to
investigate the structural behavior including crack patterns, failure
mode, ultimate load and load deflection behaviour. Test results show
that large opening at flexure reduces the beam capacity and stiffness;
and increases cracking and deflection. A strengthening configuration
was designed for each un-strengthened beams based on their
respective crack patterns. CFRP laminates remarkably restore the
beam capacity of beam with large circular opening at flexure location
while 10% re-gain of beam capacity with square opening. The use of
CFRP laminates with the designed strengthening configuration could
significantly reduce excessive cracking and deflection and increase
the ultimate capacity and stiffness of beam.
Abstract: This study was conducted to evaluate the anti-diabetic
properties of ethanolic extract of two plants commonly used in folk
medicine, Mormodica charantia (bitter melon) and Trigonella
foenum-graecum (fenugreek). The study was performed on STZinduced
diabetic rats (DM type-I). Plant extracts of these two plants
were given to STZ diabetic rats at the concentration of 500 mg/kg
body weight ,50 mg/kg body weight respectively. Cidophage®
(metformin HCl) were administered to another group to support the
results at a dose of 500 mg/kg body weight, the ethanolic extracts and
Cidophage administered orally once a day for four weeks using a
stomach tube and; serum samples were obtained for biochemical
analysis. The extracts caused significant decreases in glucose levels
compared with diabetic control rats. Insulin secretions were increased
after 4 weeks of treatment with Cidophage® compared with the
control non-diabetic rats. Levels of AST and ALT liver enzymes were
normalized by all treatments. Decreases in liver cholesterol,
triglycerides, and LDL in diabetic rats were observed with all
treatments. HDL levels were increased by the treatments in the
following order: bitter melon, Cidophage®, and fenugreek. Creatinine
levels were reduced by all treatments. Serum nitric oxide and
malonaldehyde levels were reduced by all extracts. GSH levels were
increased by all extracts. Extravasation as measured by the Evans
Blue test increased significantly in STZ-induced diabetic animals.
This effect was reversed by ethanolic extracts of bitter melon or
fenugreek.
Abstract: Papaya and banana bars were developed incorporating
inulin (IN) and fructooligosaccharides (FOS) (Liquid and Powder
form) in various proportions. The control bars were standardized
using 70% fruit pulp, 30% sugar, 0.3% citric acid while the treated
bars were standardized with 70% fruit pulp, 15% sugar, 15% of IN
and FOS and 0.3% citric acid. Among the various proportions tested,
papaya bars with 90% FOS (Powder) + 10% IN and banana bars with
90% FOS (liquid) + 10% IN were sensorially best accepted. The
study revealed that addition of IN and FOS improved the sensory
scores. The Physico-chemical and proximatecomposition analysis
revealed slight changes in brix°, total sugars, reducing sugars, nonreducing
sugars, moisture, protein, fat, vitamin C, ash, iron,
zinc, calcium and crude fibre between control and treated fruit bars.
Further the glycemic index of papaya bar was reduced from 65 to 54
when treated with FOS and IN.
Abstract: Thousands of masters athletes participate
quadrennially in the World Masters Games (WMG), yet this cohort
of athletes remains proportionately under-investigated. Due to a
growing global obesity pandemic in context of benefits of physical
activity across the lifespan, the prevalence of obesity in this unique
population was of particular interest. Data gathered on a sub-sample
of 535 football code athletes, aged 31-72 yrs ( =47.4, s =±7.1),
competing at the Sydney World Masters Games (2009) demonstrated
a significantly (p
Abstract: In order to Study the efficacy application of green
manure as chickpea pre plant, field experiments were carried out in
2007 and 2008 growing seasons. In this research the effects of
different strategies for soil fertilization were investigated on grain
yield and yield component, minerals, organic compounds and
cooking time of chickpea. Experimental units were arranged in splitsplit
plots based on randomized complete blocks with three
replications. Main plots consisted of (G1): establishing a mixed
vegetation of Vicia panunica and Hordeum vulgare and (G2):
control, as green manure levels. Also, five strategies for obtaining the
base fertilizer requirement including (N1): 20 t.ha-1 farmyard manure;
(N2): 10 t.ha-1 compost; (N3): 75 kg.ha-1 triple super phosphate;
(N4): 10 t.ha-1 farmyard manure + 5 t.ha-1 compost and (N5): 10 t.ha-1
farmyard manure + 5 t.ha-1 compost + 50 kg.ha-1 triple super
phosphate were considered in sub plots. Furthermoree four levels of
biofertilizers consisted of (B1): Bacillus lentus + Pseudomonas
putida; (B2): Trichoderma harzianum; (B3): Bacillus lentus +
Pseudomonas putida + Trichoderma harzianum; and (B4): control
(without biofertilizers) were arranged in sub-sub plots. Results
showed that integrating biofertilizers (B3) and green manure (G1)
produced the highest grain yield. The highest amounts of yield were
obtained in G1×N5 interaction. Comparison of all 2-way and 3-way
interactions showed that G1N5B3 was determined as the superior
treatment. Significant increasing of N, P2O5, K2O, Fe and Mg content
in leaves and grains emphasized on superiority of mentioned
treatment because each one of these nutrients has an approved role in
chlorophyll synthesis and photosynthesis abilities of the crops. The
combined application of compost, farmyard manure and chemical
phosphorus (N5) in addition to having the highest yield, had the best
grain quality due to high protein, starch and total sugar contents, low
crude fiber and reduced cooking time.
Abstract: This paper describes fast and efficient method for page segmentation of document containing nonrectangular block. The segmentation is based on edge following algorithm using small window of 16 by 32 pixels. This segmentation is very fast since only border pixels of paragraph are used without scanning the whole page. Still, the segmentation may contain error if the space between them is smaller than the window used in edge following. Consequently, this paper reduce this error by first identify the missed segmentation point using direction information in edge following then, using X-Y cut at the missed segmentation point to separate the connected columns. The advantage of the proposed method is the fast identification of missed segmentation point. This methodology is faster with fewer overheads than other algorithms that need to access much more pixel of a document.
Abstract: In an emergency, combining Wireless Sensor Network's data with the knowledge gathered from various other information sources and navigation algorithms, could help safely guide people to a building exit while avoiding the risky areas. This paper presents an emergency response and navigation support architecture for data gathering, knowledge manipulation, and navigational support in an emergency situation. At normal state, the system monitors the environment. When an emergency event detects, the system sends messages to first responders and immediately identifies the risky areas from safe areas to establishing escape paths. The main functionalities of the system include, gathering data from a wireless sensor network which is deployed in a multi-story indoor environment, processing it with information available in a knowledge base, and sharing the decisions made, with first responders and people in the building. The proposed architecture will act to reduce risk of losing human lives by evacuating people much faster with least congestion in an emergency environment.
Abstract: Signature amortization schemes have been introduced
for authenticating multicast streams, in which, a single signature is
amortized over several packets. The hash value of each packet is
computed, some hash values are appended to other packets, forming
what is known as hash chain. These schemes divide the stream into
blocks, each block is a number of packets, the signature packet in
these schemes is either the first or the last packet of the block.
Amortization schemes are efficient solutions in terms of computation
and communication overhead, specially in real-time environment.
The main effictive factor of amortization schemes is it-s hash chain
construction. Some studies show that signing the first packet of each
block reduces the receiver-s delay and prevents DoS attacks, other
studies show that signing the last packet reduces the sender-s delay.
To our knowledge, there is no studies that show which is better, to
sign the first or the last packet in terms of authentication probability
and resistance to packet loss.
In th is paper we will introduce another scheme for authenticating
multicast streams that is robust against packet loss, reduces the
overhead, and prevents the DoS attacks experienced by the receiver
in the same time. Our scheme-The Multiple Connected Chain signing
the First packet (MCF) is to append the hash values of specific
packets to other packets,then append some hashes to the signature
packet which is sent as the first packet in the block. This scheme
is aspecially efficient in terms of receiver-s delay. We discuss and
evaluate the performance of our proposed scheme against those that
sign the last packet of the block.
Abstract: This paper presents a new compact analytical model of
the gate leakage current in high-k based nano scale MOSFET by
assuming a two-step inelastic trap-assisted tunneling (ITAT) process
as the conduction mechanism. This model is based on an inelastic
trap-assisted tunneling (ITAT) mechanism combined with a semiempirical
gate leakage current formulation in the BSIM 4 model. The
gate tunneling currents have been calculated as a function of gate
voltage for different gate dielectrics structures such as HfO2, Al2O3
and Si3N4 with EOT (equivalent oxide thickness) of 1.0 nm. The
proposed model is compared and contrasted with santaurus
simulation results to verify the accuracy of the model and excellent
agreement is found between the analytical and simulated data. It is
observed that proposed analytical model is suitable for different highk
gate dielectrics simply by adjusting two fitting parameters. It was
also shown that gate leakages reduced with the introduction of high-k
gate dielectric in place of SiO2.
Abstract: Mostly, pedestrian-car accidents occurred at a
signalized interaction is because pedestrians cannot across the
intersection safely within the green light. From the viewpoint of
pedestrian, there might have two reasons. The first one is pedestrians
cannot speed up to across the intersection, such as the elders. The other
reason is pedestrians do not sense that the signal phase is going to
change and their right-of-way is going to lose. Developing signal logic
to protect pedestrian, who is crossing an intersection is the first
purpose of this study. Another purpose of this study is improving the
reliability and reduce delay of public transportation service. Therefore,
bus preemption is also considered in the designed signal logic. In this
study, the traffic data of the intersection of Chong-Qing North Road
and Min-Zu West Road, Taipei, Taiwan, is employed to calibrate and
validate the signal logic by simulation. VISSIM 5.20, which is a
microscopic traffic simulation software, is employed to simulate the
signal logic. From the simulated results, the signal logic presented in
this study can protect pedestrians crossing the intersection
successfully. The design of bus preemption can reduce the average
delay. However, the pedestrian safety and bus preemptive signal will
influence the average delay of cars largely. Thus, whether applying the
pedestrian safety and bus preemption signal logic to an isolated
intersection or not should be evaluated carefully.
Abstract: The purpose of this study is to analyze the visual
preference of patterns in pedestrian roads. In this study, animation was
applied for the estimation of dynamic streetscape. Six patterns of
pedestrian were selected in order to analyze the visual preference. The
shapes are straight, s-curve, and zigzag. The ratio of building's height
and road's width are 2:1 and 1:1. Twelve adjective pairs used in the
field investigation were selected from adjectives which are used
usually in the estimation of streetscape. They are interesting-boring,
simple-complex, calm-noisy, open-enclosed, active-inactive,
lightly-depressing, regular-irregular, unique-usual, rhythmic-not
rhythmic, united-not united, stable-unstable, tidy-untidy.
Dynamic streetscape must be considered important in pedestrian
shopping mall and park because it will be an attraction. So, s-curve
pedestrian road, which is the most beautiful as a result of this study,
should be designed in this area. Also, the ratio of building's height and
road's width along pedestrian road should be reduced.
Abstract: The present work involves measurements to examine
the effects of initial conditions on aerodynamic and acoustic
characteristics of a Jet at M=0.8 by changing the orientation of sharp
edged orifice plate. A thick plate with chamfered orifice presented divergent and convergent openings when it was flipped over. The centerline velocity was found to decay more rapidly for divergent
orifice and that was consistent with the enhanced mass entrainment
suggesting quicker spread of the jet compared with that from the convergent orifice. The mixing layer region elucidated this effect of
initial conditions at an early stage – the growth was found to be comparatively more pronounced for the divergent orifice resulting in
reduced potential core size. The acoustic measurements, carried out in the near field noise region outside the jet within potential core
length, showed the jet from the divergent orifice to be less noisy. The frequency spectra of the noise signal exhibited that in the initial
region of comparatively thin mixing layer for the convergent orifice,
the peak registered a higher SPL and a higher frequency as well. The noise spectra and the mixing layer development suggested a direct correlation between the coherent structures developing in the initial
region of the jet and the noise captured in the surrounding near field.
Abstract: Grasslands of Iran are encountered with a vast
desertification and destruction. Some legumes are plants of forage
importance with high palatability. Studied legumes in this project are
Onobrychis, Medicago sativa (alfalfa) and Trifolium repens. Seeds
were cultivated in research field of Kaboutarabad (33 km East of
Isfahan, Iran) with an average 80 mm. annual rainfall. Plants were
cultivated in a split plot design with 3 replicate and two water
treatments (weekly irrigation, and under stress with same amount per
15 days interval). Water entrance to each plots were measured by
Partial flow. This project lasted 20 weeks. Destructive samplings
(1m2 each time) were done weekly. At each sampling plants were
gathered and weighed separately for each vegetative parts. An Area
Meter (Vista) was used to measure root surface and leaf area. Total
shoot and root fresh and dry weight, leaf area index and soil coverage
were evaluated too. Dry weight was achieved in 750c oven after 24
hours. Statgraphic and Harvard Graphic software were used to
formulate and demonstrate the parameters curves due to time. Our
results show that Trifolium repens has affected 60 % and Medicago
sativa 18% by water stress. Onobrychis total fresh weight was
reduced 45%. Dry weight or Biomass in alfalfa is not so affected by
water shortage. This means that in alfalfa fields we can decrease the
irrigation amount and have some how same amount of Biomass.
Onobrychis show a drastic decrease in Biomass. The increases in
total dry matter due to time in studied plants are formulated. For
Trifolium repens if removal or cattle entrance to meadows do not
occurred at perfect time, it will decrease the palatability and water
content of the shoots. Water stress in a short period could develop the
root system in Trifolium repens, but if it last more than this other
ecological and soil factors will affect the growth of this plant. Low
level of soil water is not so important for studied legume forges. But
water shortage affect palatability and water content of aerial parts.
Leaf area due to time in studied legumes is formulated. In fact leaf
area is decreased by shortage in available water. Higher leaf area
means higher forage and biomass production. Medicago and
Onobrychis reach to the maximum leaf area sooner than Trifolium
and are able to produce an optimum soil cover and inhibit the
transpiration of soil water of meadows. Correlation of root surface to
Total biomass in studied plants is formulated. Medicago under water
stress show a 40% decrease in crown cover while at optimum
condition this amount reach to 100%. In order to produce forage in
areas without soil erosion Medicago is the best choice even with a
shortage in water resources. It is tried to represent the growth
simulation of three famous Forage Legumes. By growth simulation
farmers and range managers could better decide to choose best plant
adapted to water availability without designing different time and
labor consuming field experiments.
Abstract: Text categorization is the problem of classifying text
documents into a set of predefined classes. After a preprocessing
step, the documents are typically represented as large sparse vectors.
When training classifiers on large collections of documents, both the
time and memory restrictions can be quite prohibitive. This justifies
the application of feature selection methods to reduce the
dimensionality of the document-representation vector. In this paper,
we present three feature selection methods: Information Gain,
Support Vector Machine feature selection called (SVM_FS) and
Genetic Algorithm with SVM (called GA_SVM). We show that the
best results were obtained with GA_SVM method for a relatively
small dimension of the feature vector.
Abstract: Knowledge sharing culture contributes to a positive
working environment. Currently, there is no platform for the Faculty
of Industrial Information Technology (FIIT), Unisel academic staff to
share knowledge among them. As it is done manually, the sharing
process is through common meeting or by any offline discussions.
There is no repository for future retrieval. However, with open
source solution the development of knowledge based application may
reduce the cost tremendously. In this paper we discuss about the
domain on which this knowledge portal is being developed and also
the deployment of open source tools such as JOOMLA, PHP
programming language and MySQL. This knowledge portal is
evidence that open source tools also reliable in developing
knowledge based portal. These recommendations will be useful to
the open source community to produce more open source products in
future.
Abstract: Particle damping is a technique to reduce the
structural vibrations by means of placing small metallic particles
inside a cavity that is attached to the structure at location of high
vibration amplitudes. In this paper, we have presented an analytical
model to simulate the particle damping of two dimensional transient
vibrations in structure operating under high centrifugal loads. The
simulation results show that this technique remains effective as long
as the ratio of the dynamic acceleration of the structure to the applied
centrifugal load is more than 0.1. Particle damping increases with the
increase of particle to structure mass ratio. However, unlike to the
case of particle damping in the absence of centrifugal loads where
the damping efficiency strongly depends upon the size of the cavity,
here this dependence becomes very weak. Despite the simplicity of
the model, the simulation results are considerably in good agreement
with the very scarce experimental data available in the literature for
particle damping under centrifugal loads.
Abstract: The orthogonal processes to shape the triangle steel plate into a equilateral vertical steel are examined by an incremental elasto-plastic finite-element method based on an updated Lagrangian formulation. The highly non-linear problems due to the geometric changes, the inelastic constitutive behavior and the boundary conditions varied with deformation are taken into account in an incremental manner. On the contact boundary, a modified Coulomb friction mode is specially considered. A weighting factor r-minimum is employed to limit the step size of loading increment to linear relation. In particular, selective reduced integration was adopted to formulate the stiffness matrix. The simulated geometries of verticality could clearly demonstrate the vertical processes until unloading. A series of experiments and simulations were performed to validate the formulation in the theory, leading to the development of the computer codes. The whole deformation history and the distribution of stress, strain and thickness during the forming process were obtained by carefully considering the moving boundary condition in the finite-element method. Therefore, this modeling can be used for judging whether a equilateral vertical steel can be shaped successfully. The present work may be expected to improve the understanding of the formation of the equilateral vertical steel.
Abstract: One of the main objectives of order reduction is to
design a controller of lower order which can effectively control the
original high order system so that the overall system is of lower
order and easy to understand. In this paper, a simple method is
presented for controller design of a higher order discrete system.
First the original higher order discrete system in reduced to a lower
order model. Then a Proportional Integral Derivative (PID)
controller is designed for lower order model. An error minimization
technique is employed for both order reduction and controller
design. For the error minimization purpose, Differential Evolution
(DE) optimization algorithm has been employed. DE method is
based on the minimization of the Integral Squared Error (ISE)
between the desired response and actual response pertaining to a
unit step input. Finally the designed PID controller is connected to
the original higher order discrete system to get the desired
specification. The validity of the proposed method is illustrated
through a numerical example.
Abstract: Any use of energy in industrial productive activities is combined with various environment impacts. Withintransportation,
this fact was not only found among land transport, railways and maritime transport, but also in the air transport industry. An effective climate protection requires strategies and measures for reducing all
greenhouses gas emissions, in particular carbon dioxide, and must
take into account the economic, ecologic and social aspects. It seem simperative now to develop and manufacture environmentally
friendly products and systems, to reduce consumption and use less
resource, and to save energy and power. Today-sproducts could
better serve these requirements taking into account the integration of
a power management system into the electrical power system.This
paper gives an overview of an approach ofpower management with
load prioritization in modernaircraft. Load dimensioning and load
management strategies on current civil aircraft will be presented and
used as a basis for the proposed approach.
Abstract: One of the major pollutants in the environment is arsenic (As). Due to the toxic effects of As to all organisms, its remediation is necessary. Conventional technologies used in the remediation of As contaminated soils are expensive and may even compromise the structure of the soil. An attractive alternative is phytoremediation, which is the use of plants which can take up the contaminant in their tissues. Plant growth promoting bacteria (PGPB) has been known to enhance growth of plants through several mechanisms such as phytohormone production, phosphate solubilization, siderophore production and 1-aminocyclopropane-1- carboxylate (ACC) deaminase production, which is an essential trait that aids plants especially under stress conditions such as As stress. Twenty one bacteria were isolated from As-contaminated soils in the vicinity of the Janghang Smelter in Chungnam Province, South Korea. These exhibited high tolerance to either arsenite (As III) or arsenate (As V) or both. Most of these isolates possess several plant growth promoting traits which can be potentially exploited to increase phytoremediation efficiency. Among the identified isolates is Pseudomonas sp. JS1215, which produces ACC deaminase, indole acetic acid (IAA), and siderophore. It also has the ability to solubilize phosphate. Inoculation of JS1215 significantly enhanced root and shoot length and biomass accumulation of maize under normal conditions. In the presence of As, particularly in lower As level, inoculation of JS1215 slightly increased root length and biomass. Ethylene increased with increasing As concentration, but was reduced by JS1215 inoculation. JS1215 can be a potential bioinoculant for increasing phytoremediation efficiency.